On Thursday 12 March 2020 08:53:39 Leonardo Marsaglia wrote: > I'm going to check the flat cable, that I'm missing. > > El jue., 12 mar. 2020 a las 9:48, Leonardo Marsaglia > (<ldmarsag...@gmail.com>) > > escribió > : I was gonna suggest that, Leonardo, I've had flat cables that had gone funkity in just a year because they needed another trip thru the vice to bring the crimps and the idc connectors fully together because they never fully latched the first time. And age of the connector can be important if its not visibly gold flashed. Those tend to get intermittent in 5 to 10 years. Cut the old connector off flush and put a new plated connector on it if its still long enough to reach, or order both connectors and enough cable to make a new one that will reach.
> > Hello again, > > > > I'm almost done with testing, but I have a little problem with the > > 7i52s on stepgen 0. I can measure the direction pin changing with or > > without /TX0BENA enabled (that is gpio 023 on 0 since I have the > > 7i52s on P2 of the 6i24), I don't know if this is normal. And also, > > I can't sense any pulses comming out of stepgen 0, but stepgen 1 is > > working ok. > > > > I'm I missing something? > > > > Thank you! > > > > El lun., 9 mar. 2020 a las 20:33, andrew beck > > (<andrewbeck0...@gmail.com>) > > > > escribió: > >> Hey just a quick question on this. Is it possible to take one is > >> these iso > >> files update to linuxcnc 2.8 and then load it all onto a USB so I > >> don't have to go through the whole update thing every time I want > >> to install linuxcnc 2.8 on mint? > >> > >> Regards > >> > >> Andrew > >> > >> On Tue, Mar 10, 2020, 10:58 AM Robert Murphy > >> <robert.mur...@gmx.com> > >> > >> wrote: > >> > They are =E2=80=9Ctesting=E2=80=9D in case the guy who put them > >> > together mes= > >> > sed up. > >> > All they are is a std Mint ISO with what is required to run > >> > linuxcnc. > >> > >> They > >> > >> > c= > >> > an be installed and are good for a system, so far as no one has > >> > reported any= > >> > major issues. > >> > Please read the first page fully, then follow the link to the > >> > >> appropriate > >> > >> > pa= > >> > ge, read that and download.=20 > >> > > >> > Composed with my Crayons=20 > >> > > >> > On 10 Mar 2020, at 04:31, Leonardo Marsaglia > >> > <ldmarsag...@gmail.com> > >> > > >> > wrote: > >> > >>=20 > >> > >> The kernel in the latest ISOs, from my testing, has better > >> > >> latency > >> > >> than > >> > >> > >> the K=3D > >> > >> ona kernel. Cinnamon is quite resource hungry, MATE is next > >> > >> and XFCE > >> > >> is > >> > >> > >> the l=3D > >> > >> ightest of the three.=3D20 > >> > >> Wireless can have a negative effect . Out of interest what > >> > >> machine or mother=3D > >> > >> board specs have you got at your disposal? > >> > > > >> > >=20 > >> > >=20 > >> > > I'm using an ASUS A58M-5 with a PCI-Express gpu. I didn't wan > >> > > to use > >> > >> the > >> > >> > > onboard just in case it increases the latency. The > >> > > microprocessor is > >> > >> an > >> > >> > > AMD A4 4000. > >> > >=20 > >> > > El lun., 9 mar. 2020 a las 14:27, Leonardo Marsaglia > >> > > >> > (<ldmarsaglia@gmail.c= > >> > om>) > >> > > >> > > escribi=C3=B3: > >> > >=20 > >> > > > >> > >> Why? > >> > >> > >> > >>> The link I gave was to ISO images for prempt-rt and rtai. > >> > >>>=20 > >> > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > >>so-wi= > >> > >> > th-rtai-and-rt?start=3D0 > >> > < > >> > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > >>so-wi=th-rtai-and-rt?start=3D0 > >> > >> > >>=20 > >> > >>=20 > >> > >> I tried the one on the link to the other thread because the > >> > >> ones > >> > >> shared > >> > >> > o= > >> > n > >> > > >> > >> drive are meant to be used as live cd for testing, at least > >> > >> that's > >> > >> what > >> > >> > i= > >> > t > >> > > >> > >> says there. But I can give it a try after work. Let me know if > >> > >> I > >> > >> missed > >> > >> > >> something. > >> > >>=20 > >> > >> El lun., 9 mar. 2020 a las 14:13, Robert Murphy (< > >> > >> robert.mur...@gmx.com > >> > >> > >)= > >> > > > >> > >> escribi=C3=B3: > >> > >>=20 > >> > >> > >> > >>> The kernel in the latest ISOs, from my testing, has better > >> > >>> latency > >> > >> than > >> > >> > >>> the K=3D > >> > >>> ona kernel. Cinnamon is quite resource hungry, MATE is next > >> > >>> and > >> > >> XFCE is > >> > >> > >>> the l=3D > >> > >>> ightest of the three.=3D20 > >> > >>> Wireless can have a negative effect . Out of interest what > >> > >>> machine > >> > >> or > >> > >> > >>> mother=3D > >> > >>> board specs have you got at your disposal? > >> > >>>=20 > >> > >>> Composed with my Crayons=3D20 > >> > >>>=20 > >> > >>> > >> > >>>>> On 10 Mar 2020, at 02:10, andy pugh <bodge...@gmail.com> > >> > >>>>> wrote: =3D20 > >> > >>>>> On Mon, 9 Mar 2020 at 14:18, Leonardo Marsaglia < > >> > > >> > ldmarsag...@gmail.com= > >> > > >> > >>> w=3D > >> > >>> > >> > >>> rote: > >> > >>>>> =3D20 > >> > >>>>> I tried Cinnamon desktop and intalled the kernel following > >> > >>>>> the > >> > >>> > >> > >>> instructio=3D > >> > >>> ns > >> > >>> > >> > >>>>> here : > >> > >>>>>=20 > >> > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc-on- > >>linux= > >> > >> > -=3D > >> > < > >> > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc-on- > >>linux=-=3D > >> > >> > >>> mint-19-1-quick-and-easy-installation?start=3D3D0 > >> > >>> < > >> > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc-on- > >>linu= > >> > >> > x-=3Dmint-19-1-quick-and-easy-installation?start=3D3D0 > >> > < > >> > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc-on- > >>linu=x-=3Dmint-19-1-quick-and-easy-installation?start=3D3D0 > >> > >> > >>>> =3D20 > >> > >>>> Why? > >> > >>>> =3D20 > >> > >>>> The link I gave was to ISO images for prempt-rt and rtai. > >> > >>>> =3D20 > >> > >>>>=20 > >> > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > >>so-wi= > >> > >> > th=3D > >> > < > >> > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > >>so-wi=th=3D > >> > >> > >>> -rtai-and-rt?start=3D3D0 > >> > >>> < > >> > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > >>so-w= > >> > >> > ith=3D-rtai-and-rt?start=3D3D0 > >> > < > >> > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > >>so-w=ith=3D-rtai-and-rt?start=3D3D0 > >> > >> > >>>> =3D20 > >> > >>>> --=3D20 > >> > >>>> atp > >> > >>>> "A motorcycle is a bicycle with a pandemonium attachment and > >> > >>>> is designed for the especial use of mechanical geniuses, > >> > >>>> daredevils > >> > >> and > >> > >> > >>>> lunatics." > >> > >>>> =3DE2=3D80=3D94 George Fitch, Atlanta Constitution > >> > >>>> Newspaper, 1912 =3D20 > >> > >>>> =3D20 > >> > >>>> _______________________________________________ > >> > >>>> Emc-users mailing list > >> > >>>> Emc-users@lists.sourceforge.net > >> > >>>> https://lists.sourceforge.net/lists/listinfo/emc-users > >> > >>> > >> > >>>=20 > >> > >>>=20 > >> > >>>=20 > >> > >>> _______________________________________________ > >> > >>> Emc-users mailing list > >> > >>> Emc-users@lists.sourceforge.net > >> > >>> https://lists.sourceforge.net/lists/listinfo/emc-users > >> > >>>=20 > >> > >> > >> > >>=20 > >> > > > >> > >=20 > >> > > _______________________________________________ > >> > > Emc-users mailing list > >> > > Emc-users@lists.sourceforge.net > >> > > https://lists.sourceforge.net/lists/listinfo/emc-users > >> > > >> > _______________________________________________ > >> > Emc-users mailing list > >> > Emc-users@lists.sourceforge.net > >> > https://lists.sourceforge.net/lists/listinfo/emc-users > >> > >> _______________________________________________ > >> Emc-users mailing list > >> Emc-users@lists.sourceforge.net > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users Cheers, Gene Heskett -- "There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order." -Ed Howdershelt (Author) If we desire respect for the law, we must first make the law respectable. - Louis D. Brandeis Genes Web page <http://geneslinuxbox.net:6309/gene> _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
