Here it is. El jue., 12 mar. 2020 a las 16:40, Peter C. Wallace (<p...@mesanet.com>) escribió:
> On Thu, 12 Mar 2020, Leonardo Marsaglia wrote: > > > Date: Thu, 12 Mar 2020 16:28:56 -0300 > > From: Leonardo Marsaglia <ldmarsag...@gmail.com> > > Reply-To: "Enhanced Machine Controller (EMC)" > > <emc-users@lists.sourceforge.net> > > To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net > > > > Subject: Re: [Emc-users] 6i24 + 7i44 configuration > > > > Well, the only place where the 6i24 pins could've made contact is > against the GPU aluminum heatsink. Unfortunately I can't reposition any of > the boards so I can only isolate the bottom face of the 6i24. Next board > surely will be an ethernet one. > > >About the problem of not seing the gpio.000 in the parameters. Could it be > >a firmware issue? > > Yes please run > > sudo mesaflash --device 6i24 --readhmid > pins.txt > > and post the results here > > El jue., 12 mar. 2020 a las 16:17, Peter C. Wallace (<p...@mesanet.com>) > escribiÿÿ: > > > On Thu, 12 Mar 2020, Gene Heskett wrote: > > > > > Date: Thu, 12 Mar 2020 14:52:47 -0400 > > > From: Gene Heskett <ghesk...@shentel.net> > > > Reply-To: "Enhanced Machine Controller (EMC)" > > > <emc-users@lists.sourceforge.net> > > > To: emc-users@lists.sourceforge.net > > > Subject: Re: [Emc-users] 6i24 + 7i44 configuration > > > > > > On Thursday 12 March 2020 12:23:06 Leonardo Marsaglia wrote: > > > > > Well, I checked the cable for continuity on those pins and everything > > > seems to be ok. I still can't output pulses from those pins. I can > > > only sense the direction changing. The only thing I can come up with > > > is to shift to stepgen 1 and 2 for X and Z and leave stepgen 0 unused. > > > At least until I can solve the problem. > > > > >Theres also the possibility of a damaged output gate in the fpga. they > > >are only 3.3 volt fpga's, and 5 volts is enough to write their obits. > > > > Not quite true, the FPGA I/O bits are 5V tolerant (and safe to about +7V) > > What > > typically damages outputs is negative inputs without current limiting. 1V > > of HF > > noise without some current limit will damage and short the input > > protection > > diodes. This is easy to generate just by touching bare FPGA pins to frame > > ground > > in a system with motor drives (step drives, servo drives, VFDs all > > generate > > significant ground bumping, often multiple volts in the frame ground) > > > > > > >I damaged a couple 7i90HD's until I put 7i42TA's into the setup for > > >overvoltage buffers, no problems since and they do give you nice screw > > >terminals for hookups. My current setup has 2 blown stepgens so I have > > >4 enabled, useing 2 and 3 in place of 0 and 1. Thats a custom hal file > > >but no problem for me, and LCNC doesn't care if you diddle the hal file > > >to fix our stupids. :) So if there are spares, use them. > > > > > El jue., 12 mar. 2020 a las 11:03, Gene Heskett > > > (<ghesk...@shentel.net>) > > > > > > escribiÿÿÿÿ: > > > > On Thursday 12 March 2020 08:53:39 Leonardo Marsaglia wrote: > > > > > I'm going to check the flat cable, that I'm missing. > > > > > > > > > > El jue., 12 mar. 2020 a las 9:48, Leonardo Marsaglia > > > > > (<ldmarsag...@gmail.com>) > > > > > > > > > > escribiÿÿÿÿ > > > > > > > > I was gonna suggest that, Leonardo, I've had flat cables that had > > > > gone funkity in just a year because they needed another trip thru > > > > the vice to bring the crimps and the idc connectors fully together > > > > because they never fully latched the first time. And age of the > > > > connector can be important if its not visibly gold flashed. Those > > > > tend to get intermittent in 5 to 10 years. Cut the old connector off > > > > flush and put a new plated connector on it if its still long enough > > > > to reach, or order both connectors and enough cable to make a new > > > > one that will reach. > > > > > > > > > > Hello again, > > > > > > > > > > > > I'm almost done with testing, but I have a little problem with > > > > > > the 7i52s on stepgen 0. I can measure the direction pin changing > > > > > > with or without /TX0BENA enabled (that is gpio 023 on 0 since I > > > > > > have the 7i52s on P2 of the 6i24), I don't know if this is > > > > > > normal. And also, I can't sense any pulses comming out of > > > > > > stepgen 0, but stepgen 1 is working ok. > > > > > > > > > > > > I'm I missing something? > > > > > > > > > > > > Thank you! > > > > > > > > > > > > El lun., 9 mar. 2020 a las 20:33, andrew beck > > > > > > (<andrewbeck0...@gmail.com>) > > > > > > > > > > > > escribiÿÿÿÿ: > > > > > >> Hey just a quick question on this. Is it possible to take one > > > > > >> is these iso > > > > > >> files update to linuxcnc 2.8 and then load it all onto a USB so > > > > > >> I don't have to go through the whole update thing every time I > > > > > >> want to install linuxcnc 2.8 on mint? > > > > > >> > > > > > >> Regards > > > > > >> > > > > > >> Andrew > > > > > >> > > > > > >> On Tue, Mar 10, 2020, 10:58 AM Robert Murphy > > > > > >> <robert.mur...@gmx.com> > > > > > >> > > > > > >> wrote: > > > > > >> > They are =E2=80=9Ctesting=E2=80=9D in case the guy who put > > > > > >> > them together mes= > > > > > >> > sed up. > > > > > >> > All they are is a std Mint ISO with what is required to run > > > > > >> > linuxcnc. > > > > > >> > > > > > >> They > > > > > >> > > > > > >> > c= > > > > > >> > an be installed and are good for a system, so far as no one > > > > > >> > has reported any= > > > > > >> > major issues. > > > > > >> > Please read the first page fully, then follow the link to the > > > > > >> > > > > > >> appropriate > > > > > >> > > > > > >> > pa= > > > > > >> > ge, read that and download.=20 > > > > > >> > > > > > > >> > Composed with my Crayons=20 > > > > > >> > > > > > > >> > On 10 Mar 2020, at 04:31, Leonardo Marsaglia > > > > > >> > <ldmarsag...@gmail.com> > > > > > >> > > > > > > >> > wrote: > > > > > >> > >>=20 > > > > > >> > >> The kernel in the latest ISOs, from my testing, has better > > > > > >> > >> latency > > > > > >> > > > > > >> than > > > > > >> > > > > > >> > >> the K=3D > > > > > >> > >> ona kernel. Cinnamon is quite resource hungry, MATE is > > > > > >> > >> next and XFCE > > > > > >> > > > > > >> is > > > > > >> > > > > > >> > >> the l=3D > > > > > >> > >> ightest of the three.=3D20 > > > > > >> > >> Wireless can have a negative effect . Out of interest what > > > > > >> > >> machine or mother=3D > > > > > >> > >> board specs have you got at your disposal? > > > > > >> > > > > > > > >> > >=20 > > > > > >> > >=20 > > > > > >> > > I'm using an ASUS A58M-5 with a PCI-Express gpu. I didn't > > > > > >> > > wan to use > > > > > >> > > > > > >> the > > > > > >> > > > > > >> > > onboard just in case it increases the latency. The > > > > > >> > > microprocessor is > > > > > >> > > > > > >> an > > > > > >> > > > > > >> > > AMD A4 4000. > > > > > >> > >=20 > > > > > >> > > El lun., 9 mar. 2020 a las 14:27, Leonardo Marsaglia > > > > > >> > > > > > > >> > (<ldmarsaglia@gmail.c= > > > > > >> > om>) > > > > > >> > > > > > > >> > > escribi=C3=B3: > > > > > >> > >=20 > > > > > >> > > > > > > > >> > >> Why? > > > > > >> > >> > > > > > >> > >>> The link I gave was to ISO images for prempt-rt and rtai. > > > > > >> > >>>=20 > > > > > >> > > > > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mi > > > > > >>nt-i so-wi= > > > > > >> > > > > > >> > th-rtai-and-rt?start=3D0 > > > > > >> > < > > > > > >> > > > > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mi > > > > > >>nt-i so-wi=th-rtai-and-rt?start=3D0 > > > > > >> > > > > > >> > >>=20 > > > > > >> > >>=20 > > > > > >> > >> I tried the one on the link to the other thread because > > > > > >> > >> the ones > > > > > >> > > > > > >> shared > > > > > >> > > > > > >> > o= > > > > > >> > n > > > > > >> > > > > > > >> > >> drive are meant to be used as live cd for testing, at > > > > > >> > >> least that's > > > > > >> > > > > > >> what > > > > > >> > > > > > >> > i= > > > > > >> > t > > > > > >> > > > > > > >> > >> says there. But I can give it a try after work. Let me > > > > > >> > >> know if I > > > > > >> > > > > > >> missed > > > > > >> > > > > > >> > >> something. > > > > > >> > >>=20 > > > > > >> > >> El lun., 9 mar. 2020 a las 14:13, Robert Murphy (< > > > > > >> > > > > > >> robert.mur...@gmx.com > > > > > >> > > > > > >> > >)= > > > > > >> > > > > > > > >> > >> escribi=C3=B3: > > > > > >> > >>=20 > > > > > >> > >> > > > > > >> > >>> The kernel in the latest ISOs, from my testing, has > > > > > >> > >>> better latency > > > > > >> > > > > > >> than > > > > > >> > > > > > >> > >>> the K=3D > > > > > >> > >>> ona kernel. Cinnamon is quite resource hungry, MATE is > > > > > >> > >>> next and > > > > > >> > > > > > >> XFCE is > > > > > >> > > > > > >> > >>> the l=3D > > > > > >> > >>> ightest of the three.=3D20 > > > > > >> > >>> Wireless can have a negative effect . Out of interest > > > > > >> > >>> what machine > > > > > >> > > > > > >> or > > > > > >> > > > > > >> > >>> mother=3D > > > > > >> > >>> board specs have you got at your disposal? > > > > > >> > >>>=20 > > > > > >> > >>> Composed with my Crayons=3D20 > > > > > >> > >>>=20 > > > > > >> > >>> > > > > > >> > >>>>> On 10 Mar 2020, at 02:10, andy pugh > > > > > >> > >>>>> <bodge...@gmail.com> wrote: =3D20 > > > > > >> > >>>>> On Mon, 9 Mar 2020 at 14:18, Leonardo Marsaglia < > > > > > >> > > > > > > >> > ldmarsag...@gmail.com= > > > > > >> > > > > > > >> > >>> w=3D > > > > > >> > >>> > > > > > >> > >>> rote: > > > > > >> > >>>>> =3D20 > > > > > >> > >>>>> I tried Cinnamon desktop and intalled the kernel > > > > > >> > >>>>> following the > > > > > >> > >>> > > > > > >> > >>> instructio=3D > > > > > >> > >>> ns > > > > > >> > >>> > > > > > >> > >>>>> here : > > > > > >> > >>>>>=20 > > > > > >> > > > > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc > > > > > >>-on- linux= > > > > > >> > > > > > >> > -=3D > > > > > >> > < > > > > > >> > > > > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc > > > > > >>-on- linux=-=3D > > > > > >> > > > > > >> > >>> mint-19-1-quick-and-easy-installation?start=3D3D0 > > > > > >> > >>> < > > > > > >> > > > > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc > > > > > >>-on- linu= > > > > > >> > > > > > >> > x-=3Dmint-19-1-quick-and-easy-installation?start=3D3D0 > > > > > >> > < > > > > > >> > > > > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc > > > > > >>-on- linu=x-=3Dmint-19-1-quick-and-easy-installation?start=3D3D0 > > > > > >> > > > > > >> > >>>> =3D20 > > > > > >> > >>>> Why? > > > > > >> > >>>> =3D20 > > > > > >> > >>>> The link I gave was to ISO images for prempt-rt and > > > > > >> > >>>> rtai. =3D20 > > > > > >> > >>>>=20 > > > > > >> > > > > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mi > > > > > >>nt-i so-wi= > > > > > >> > > > > > >> > th=3D > > > > > >> > < > > > > > >> > > > > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mi > > > > > >>nt-i so-wi=th=3D > > > > > >> > > > > > >> > >>> -rtai-and-rt?start=3D3D0 > > > > > >> > >>> < > > > > > >> > > > > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mi > > > > > >>nt-i so-w= > > > > > >> > > > > > >> > ith=3D-rtai-and-rt?start=3D3D0 > > > > > >> > < > > > > > >> > > > > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mi > > > > > >>nt-i so-w=ith=3D-rtai-and-rt?start=3D3D0 > > > > > >> > > > > > > Cheers, Gene Heskett > > -- > > "There are four boxes to be used in defense of liberty: > > soap, ballot, jury, and ammo. Please use in that order." > > -Ed Howdershelt (Author) > > If we desire respect for the law, we must first make the law respectable. > > - Louis D. Brandeis > > Genes Web page <http://geneslinuxbox.net:6309/gene> > > > > > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > Peter Wallace > > Mesa Electronics > > > > (\__/) > > (='.'=) This is Bunny. Copy and paste bunny into your > > (")_(") signature to help him gain world domination. > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > > Peter Wallace > Mesa Electronics > > (\__/) > (='.'=) This is Bunny. Copy and paste bunny into your > (")_(") signature to help him gain world domination. > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users >
Configuration Name: HOSTMOT2 General configuration information: BoardName : MESA5I24 FPGA Size: 25 KGates FPGA Pins: 256 Number of IO Ports: 3 Width of one I/O port: 24 Clock Low frequency: 33.3333 MHz Clock High frequency: 200.0000 MHz IDROM Type: 3 Instance Stride 0: 4 Instance Stride 1: 64 Register Stride 0: 256 Register Stride 1: 256 Modules in configuration: Module: WatchDog There are 1 of WatchDog in configuration Version: 0 Registers: 3 BaseAddress: 0C00 ClockFrequency: 33.333 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: IOPort There are 3 of IOPort in configuration Version: 0 Registers: 5 BaseAddress: 1000 ClockFrequency: 33.333 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: MuxedQCount There are 12 of MuxedQCount in configuration Version: 4 Registers: 5 BaseAddress: 3600 ClockFrequency: 33.333 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: MuxedQCountSel There are 1 of MuxedQCountSel in configuration Version: 0 Registers: 0 BaseAddress: 0000 ClockFrequency: 33.333 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: SSerial There are 1 of SSerial in configuration Version: 0 Registers: 6 BaseAddress: 5B00 ClockFrequency: 33.333 MHz Register Stride: 256 bytes Instance Stride: 64 bytes Module: StepGen There are 12 of StepGen in configuration Version: 2 Registers: 10 BaseAddress: 2000 ClockFrequency: 33.333 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Module: LED There are 1 of LED in configuration Version: 0 Registers: 1 BaseAddress: 0200 ClockFrequency: 33.333 MHz Register Stride: 256 bytes Instance Stride: 4 bytes Configuration pin-out: IO Connections for P4 Pin# I/O Pri. func Sec. func Chan Pin func Pin Dir 1 0 IOPort SSerial 0 RXData1 (In) 3 1 IOPort SSerial 0 RXData2 (In) 5 2 IOPort SSerial 0 RXData3 (In) 7 3 IOPort SSerial 0 RXData4 (In) 9 4 IOPort SSerial 0 TXData1 (Out) 11 5 IOPort SSerial 0 TXEn1 (Out) 13 6 IOPort SSerial 0 TXData2 (Out) 15 7 IOPort SSerial 0 TXEn2 (Out) 17 8 IOPort SSerial 0 TXData3 (Out) 19 9 IOPort SSerial 0 TXEn3 (Out) 21 10 IOPort SSerial 0 TXData4 (Out) 23 11 IOPort SSerial 0 TXEn4 (Out) 25 12 IOPort SSerial 0 RXData5 (In) 27 13 IOPort SSerial 0 RXData6 (In) 29 14 IOPort SSerial 0 RXData7 (In) 31 15 IOPort SSerial 0 RXData8 (In) 33 16 IOPort SSerial 0 TXData5 (Out) 35 17 IOPort SSerial 0 TXEn5 (Out) 37 18 IOPort SSerial 0 TXData6 (Out) 39 19 IOPort SSerial 0 TXEn6 (Out) 41 20 IOPort SSerial 0 TXData7 (Out) 43 21 IOPort SSerial 0 TXEn7 (Out) 45 22 IOPort SSerial 0 TXData8 (Out) 47 23 IOPort SSerial 0 TXEn8 (Out) IO Connections for P3 Pin# I/O Pri. func Sec. func Chan Pin func Pin Dir 1 24 IOPort None 3 25 IOPort MuxedQCount 3 MuxQ-A (In) 5 26 IOPort MuxedQCount 3 MuxQ-B (In) 7 27 IOPort MuxedQCount 3 MuxQ-IDX (In) 9 28 IOPort MuxedQCount 4 MuxQ-A (In) 11 29 IOPort MuxedQCount 4 MuxQ-B (In) 13 30 IOPort MuxedQCount 4 MuxQ-IDX (In) 15 31 IOPort MuxedQCount 5 MuxQ-A (In) 17 32 IOPort MuxedQCount 5 MuxQ-B (In) 19 33 IOPort MuxedQCount 5 MuxQ-IDX (In) 21 34 IOPort MuxedQCountSel 6 MuxSel0 (Out) 23 35 IOPort StepGen 11 Step/Table1 (Out) 25 36 IOPort StepGen 11 Dir/Table2 (Out) 27 37 IOPort StepGen 10 Step/Table1 (Out) 29 38 IOPort StepGen 10 Dir/Table2 (Out) 31 39 IOPort StepGen 9 Step/Table1 (Out) 33 40 IOPort StepGen 9 Dir/Table2 (Out) 35 41 IOPort StepGen 8 Step/Table1 (Out) 37 42 IOPort StepGen 8 Dir/Table2 (Out) 39 43 IOPort StepGen 7 Step/Table1 (Out) 41 44 IOPort StepGen 7 Dir/Table2 (Out) 43 45 IOPort StepGen 6 Step/Table1 (Out) 45 46 IOPort StepGen 6 Dir/Table2 (Out) 47 47 IOPort None IO Connections for P2 Pin# I/O Pri. func Sec. func Chan Pin func Pin Dir 1 48 IOPort None 3 49 IOPort MuxedQCount 0 MuxQ-A (In) 5 50 IOPort MuxedQCount 0 MuxQ-B (In) 7 51 IOPort MuxedQCount 0 MuxQ-IDX (In) 9 52 IOPort MuxedQCount 1 MuxQ-A (In) 11 53 IOPort MuxedQCount 1 MuxQ-B (In) 13 54 IOPort MuxedQCount 1 MuxQ-IDX (In) 15 55 IOPort MuxedQCount 2 MuxQ-A (In) 17 56 IOPort MuxedQCount 2 MuxQ-B (In) 19 57 IOPort MuxedQCount 2 MuxQ-IDX (In) 21 58 IOPort MuxedQCountSel 0 MuxSel0 (Out) 23 59 IOPort StepGen 5 Step/Table1 (Out) 25 60 IOPort StepGen 5 Dir/Table2 (Out) 27 61 IOPort StepGen 4 Step/Table1 (Out) 29 62 IOPort StepGen 4 Dir/Table2 (Out) 31 63 IOPort StepGen 3 Step/Table1 (Out) 33 64 IOPort StepGen 3 Dir/Table2 (Out) 35 65 IOPort StepGen 2 Step/Table1 (Out) 37 66 IOPort StepGen 2 Dir/Table2 (Out) 39 67 IOPort StepGen 1 Step/Table1 (Out) 41 68 IOPort StepGen 1 Dir/Table2 (Out) 43 69 IOPort StepGen 0 Step/Table1 (Out) 45 70 IOPort StepGen 0 Dir/Table2 (Out) 47 71 IOPort None
_______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
