Well, I checked the cable for continuity on those pins and everything seems to be ok. I still can't output pulses from those pins. I can only sense the direction changing. The only thing I can come up with is to shift to stepgen 1 and 2 for X and Z and leave stepgen 0 unused. At least until I can solve the problem.
El jue., 12 mar. 2020 a las 11:03, Gene Heskett (<ghesk...@shentel.net>) escribió: > On Thursday 12 March 2020 08:53:39 Leonardo Marsaglia wrote: > > > I'm going to check the flat cable, that I'm missing. > > > > El jue., 12 mar. 2020 a las 9:48, Leonardo Marsaglia > > (<ldmarsag...@gmail.com>) > > > > escribió > > : > I was gonna suggest that, Leonardo, I've had flat cables that had gone > funkity in just a year because they needed another trip thru the vice to > bring the crimps and the idc connectors fully together because they > never fully latched the first time. And age of the connector can be > important if its not visibly gold flashed. Those tend to get > intermittent in 5 to 10 years. Cut the old connector off flush and put a > new plated connector on it if its still long enough to reach, or order > both connectors and enough cable to make a new one that will reach. > > > > Hello again, > > > > > > I'm almost done with testing, but I have a little problem with the > > > 7i52s on stepgen 0. I can measure the direction pin changing with or > > > without /TX0BENA enabled (that is gpio 023 on 0 since I have the > > > 7i52s on P2 of the 6i24), I don't know if this is normal. And also, > > > I can't sense any pulses comming out of stepgen 0, but stepgen 1 is > > > working ok. > > > > > > I'm I missing something? > > > > > > Thank you! > > > > > > El lun., 9 mar. 2020 a las 20:33, andrew beck > > > (<andrewbeck0...@gmail.com>) > > > > > > escribió: > > >> Hey just a quick question on this. Is it possible to take one is > > >> these iso > > >> files update to linuxcnc 2.8 and then load it all onto a USB so I > > >> don't have to go through the whole update thing every time I want > > >> to install linuxcnc 2.8 on mint? > > >> > > >> Regards > > >> > > >> Andrew > > >> > > >> On Tue, Mar 10, 2020, 10:58 AM Robert Murphy > > >> <robert.mur...@gmx.com> > > >> > > >> wrote: > > >> > They are =E2=80=9Ctesting=E2=80=9D in case the guy who put them > > >> > together mes= > > >> > sed up. > > >> > All they are is a std Mint ISO with what is required to run > > >> > linuxcnc. > > >> > > >> They > > >> > > >> > c= > > >> > an be installed and are good for a system, so far as no one has > > >> > reported any= > > >> > major issues. > > >> > Please read the first page fully, then follow the link to the > > >> > > >> appropriate > > >> > > >> > pa= > > >> > ge, read that and download.=20 > > >> > > > >> > Composed with my Crayons=20 > > >> > > > >> > On 10 Mar 2020, at 04:31, Leonardo Marsaglia > > >> > <ldmarsag...@gmail.com> > > >> > > > >> > wrote: > > >> > >>=20 > > >> > >> The kernel in the latest ISOs, from my testing, has better > > >> > >> latency > > >> > > >> than > > >> > > >> > >> the K=3D > > >> > >> ona kernel. Cinnamon is quite resource hungry, MATE is next > > >> > >> and XFCE > > >> > > >> is > > >> > > >> > >> the l=3D > > >> > >> ightest of the three.=3D20 > > >> > >> Wireless can have a negative effect . Out of interest what > > >> > >> machine or mother=3D > > >> > >> board specs have you got at your disposal? > > >> > > > > >> > >=20 > > >> > >=20 > > >> > > I'm using an ASUS A58M-5 with a PCI-Express gpu. I didn't wan > > >> > > to use > > >> > > >> the > > >> > > >> > > onboard just in case it increases the latency. The > > >> > > microprocessor is > > >> > > >> an > > >> > > >> > > AMD A4 4000. > > >> > >=20 > > >> > > El lun., 9 mar. 2020 a las 14:27, Leonardo Marsaglia > > >> > > > >> > (<ldmarsaglia@gmail.c= > > >> > om>) > > >> > > > >> > > escribi=C3=B3: > > >> > >=20 > > >> > > > > >> > >> Why? > > >> > >> > > >> > >>> The link I gave was to ISO images for prempt-rt and rtai. > > >> > >>>=20 > > >> > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > > >>so-wi= > > >> > > >> > th-rtai-and-rt?start=3D0 > > >> > < > > >> > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > > >>so-wi=th-rtai-and-rt?start=3D0 > > >> > > >> > >>=20 > > >> > >>=20 > > >> > >> I tried the one on the link to the other thread because the > > >> > >> ones > > >> > > >> shared > > >> > > >> > o= > > >> > n > > >> > > > >> > >> drive are meant to be used as live cd for testing, at least > > >> > >> that's > > >> > > >> what > > >> > > >> > i= > > >> > t > > >> > > > >> > >> says there. But I can give it a try after work. Let me know if > > >> > >> I > > >> > > >> missed > > >> > > >> > >> something. > > >> > >>=20 > > >> > >> El lun., 9 mar. 2020 a las 14:13, Robert Murphy (< > > >> > > >> robert.mur...@gmx.com > > >> > > >> > >)= > > >> > > > > >> > >> escribi=C3=B3: > > >> > >>=20 > > >> > >> > > >> > >>> The kernel in the latest ISOs, from my testing, has better > > >> > >>> latency > > >> > > >> than > > >> > > >> > >>> the K=3D > > >> > >>> ona kernel. Cinnamon is quite resource hungry, MATE is next > > >> > >>> and > > >> > > >> XFCE is > > >> > > >> > >>> the l=3D > > >> > >>> ightest of the three.=3D20 > > >> > >>> Wireless can have a negative effect . Out of interest what > > >> > >>> machine > > >> > > >> or > > >> > > >> > >>> mother=3D > > >> > >>> board specs have you got at your disposal? > > >> > >>>=20 > > >> > >>> Composed with my Crayons=3D20 > > >> > >>>=20 > > >> > >>> > > >> > >>>>> On 10 Mar 2020, at 02:10, andy pugh <bodge...@gmail.com> > > >> > >>>>> wrote: =3D20 > > >> > >>>>> On Mon, 9 Mar 2020 at 14:18, Leonardo Marsaglia < > > >> > > > >> > ldmarsag...@gmail.com= > > >> > > > >> > >>> w=3D > > >> > >>> > > >> > >>> rote: > > >> > >>>>> =3D20 > > >> > >>>>> I tried Cinnamon desktop and intalled the kernel following > > >> > >>>>> the > > >> > >>> > > >> > >>> instructio=3D > > >> > >>> ns > > >> > >>> > > >> > >>>>> here : > > >> > >>>>>=20 > > >> > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc-on- > > >>linux= > > >> > > >> > -=3D > > >> > < > > >> > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc-on- > > >>linux=-=3D > > >> > > >> > >>> mint-19-1-quick-and-easy-installation?start=3D3D0 > > >> > >>> < > > >> > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc-on- > > >>linu= > > >> > > >> > x-=3Dmint-19-1-quick-and-easy-installation?start=3D3D0 > > >> > < > > >> > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/36822-linuxcnc-on- > > >>linu=x-=3Dmint-19-1-quick-and-easy-installation?start=3D3D0 > > >> > > >> > >>>> =3D20 > > >> > >>>> Why? > > >> > >>>> =3D20 > > >> > >>>> The link I gave was to ISO images for prempt-rt and rtai. > > >> > >>>> =3D20 > > >> > >>>>=20 > > >> > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > > >>so-wi= > > >> > > >> > th=3D > > >> > < > > >> > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > > >>so-wi=th=3D > > >> > > >> > >>> -rtai-and-rt?start=3D3D0 > > >> > >>> < > > >> > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > > >>so-w= > > >> > > >> > ith=3D-rtai-and-rt?start=3D3D0 > > >> > < > > >> > > >> https://forum.linuxcnc.org/9-installing-linuxcnc/38308-linux-mint-i > > >>so-w=ith=3D-rtai-and-rt?start=3D3D0 > > >> > > >> > >>>> =3D20 > > >> > >>>> --=3D20 > > >> > >>>> atp > > >> > >>>> "A motorcycle is a bicycle with a pandemonium attachment and > > >> > >>>> is designed for the especial use of mechanical geniuses, > > >> > >>>> daredevils > > >> > > >> and > > >> > > >> > >>>> lunatics." > > >> > >>>> =3DE2=3D80=3D94 George Fitch, Atlanta Constitution > > >> > >>>> Newspaper, 1912 =3D20 > > >> > >>>> =3D20 > > >> > >>>> _______________________________________________ > > >> > >>>> Emc-users mailing list > > >> > >>>> Emc-users@lists.sourceforge.net > > >> > >>>> https://lists.sourceforge.net/lists/listinfo/emc-users > > >> > >>> > > >> > >>>=20 > > >> > >>>=20 > > >> > >>>=20 > > >> > >>> _______________________________________________ > > >> > >>> Emc-users mailing list > > >> > >>> Emc-users@lists.sourceforge.net > > >> > >>> https://lists.sourceforge.net/lists/listinfo/emc-users > > >> > >>>=20 > > >> > >> > > >> > >>=20 > > >> > > > > >> > >=20 > > >> > > _______________________________________________ > > >> > > Emc-users mailing list > > >> > > Emc-users@lists.sourceforge.net > > >> > > https://lists.sourceforge.net/lists/listinfo/emc-users > > >> > > > >> > _______________________________________________ > > >> > Emc-users mailing list > > >> > Emc-users@lists.sourceforge.net > > >> > https://lists.sourceforge.net/lists/listinfo/emc-users > > >> > > >> _______________________________________________ > > >> Emc-users mailing list > > >> Emc-users@lists.sourceforge.net > > >> https://lists.sourceforge.net/lists/listinfo/emc-users > > > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > Cheers, Gene Heskett > -- > "There are four boxes to be used in defense of liberty: > soap, ballot, jury, and ammo. Please use in that order." > -Ed Howdershelt (Author) > If we desire respect for the law, we must first make the law respectable. > - Louis D. Brandeis > Genes Web page <http://geneslinuxbox.net:6309/gene> > > > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
