[Elecraft] K3 NR triggering
Hi Steve I also seem to get the impression that the selected NR setting is not exacty the same as the selected level within in the menu versus turning the DSP NR on and off without entering the menu, if that makes sense. What I am finding is that 2-4 when applied from within the menu, does not sound like 2-4 when directly turning the NR on and off without entering the menu. It sounds different after you go and turn NR off and then on again. Maybe its just the latency in the DSP that I am noticing. Anyway new firmware, new learning curve, who knows? Anyone else notice this? I also seem to get the impression that the noise blanker is working much better, especially the DSP blanker, which is great. 73 Craig VK3HE __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 NR triggering
Steve Ellington wrote: I just had a CW QSO on a noisy 80m. Here's what I noticed with NR set for F1-3. BW set for 2.5 kHz. QRN very loud! I pushed NR. Band goes almost totally silent. Calling CQ with the bug was like being in TX mode but I was using QSK as always. Wow...Nice and quiet. Then someone answered my CQ. On his very first DIT, the noise level jumped up and stayed up throughout the entire QSO. It was quieter than no NR at all but why should it stay that way??? Remember that NR is an adaptive filter. When you perturb it with a coherent signal it rebuilds the filter around that signal. F1 is the longest tap setting which means it has the greatest stored data stream and will take the longest to respond when you add new data (i.e. a signal). Once the new input to the filter (signal plus noise) is steady state, the filter will then stay in that state until the inputs change again (i.e. when the signal goes away). 73, Bill -- View this message in context: http://n2.nabble.com/K3-NR-triggering-tp3521099p3524344.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 NR in Ver 3.27
I have just installed 3.27 and the NR is a disaster. On turning it on there is virtually no AF output even at maximum AF gain setting. I have turned the K3 off and on but to no avail. Also there are big birdies on 40m (I haven't checked any other bands) which I am sure were not there before I upgraded from 3.25. Has anyone any ideas . If not it looks as if I will need to go back to 3.25. Barry VK2BJ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 NR
Joe: I listended with a Heil ProSet last night... I will check the impedance, dont know it offhand. True, a mismatch would add to the effect. -lu- - Original Message Follows - From: Joe Subich, W4TV li...@subich.com To: 'Lu Romero - W4LT' lrom...@ij.net, elecraft@mailman.qth.net Subject: RE: [Elecraft] [K3] K3 NR Date: Wed, 26 Aug 2009 22:19:23 -0400 I prefer the sound of the 3.25 version for ssb, its cleaner and somewhat less bright (flatter in response). I had to tweak the RX EQ to add some bass in the 3.27 version or it sounds harsh in my headsets (I dont use speakers hardly ever, btw). What is the impedance of your headphones? With anything less than 100 Ohms or so, the stock 10 uF headphone coupling caps cause a significant LF roll off - particularly with 8 Ohm cans. 73, ... Joe, W4TV -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Lu Romero - W4LT Sent: Wednesday, August 26, 2009 10:09 PM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] [K3] K3 NR Lyle: Just played with the NR in both SSB and CW, on 80 and 40. First, I can hear the change of the filters now without turning things on and off, as you mentioned it would work. The frequency response is decidedly less flat (less bassy) than the sound of 3.25. For CW, the 3 and 4 settings are much more efficient, not so in SSB, where the 1 and 2 settings are much cleaner sounding and better copy. I found that with no antenna and with the RF gain turned to 12 o'clock... Turn on the NR and all receiver white noise mutes and slowly ramps up. That's a recursive effect, I guess. I prefer the sound of the 3.25 version for ssb, its cleaner and somewhat less bright (flatter in response). I had to tweak the RX EQ to add some bass in the 3.27 version or it sounds harsh in my headsets (I dont use speakers hardly ever, btw). Inteligibility is marginally better with 3.27 on ssb and quite a bit better on CW, so you have drifted a bit to the CW side of the equation, but with a decent compromise for SSB. No more boingy peakyness in any mode, which is good, and the level while it still drops a bit, is better behaved. Can I assume from some comments I have read here that the NR process is pre EQ and AGC? How exactly do the processes stack in the radio architecture? If NR is at the top of the stack, a decent fix might be to somehow gang these three processes using presets so that they can be set up ahead of time and recalled from a memory button by the user. As an old brodcaster, we used to preset things in Switchers (vision mixers to UK readers) using a process called E-MEM... Which could recall preset parameters in salvos to preset multiple settings. This might work here. This would be handy in a contest environment where a minimum of tweaking and rapid adaptation to changing conditions is needed... You could play outside of a contest and create the settings then in the heat of battle, recall them with a single button push from a canned setup. It wouldnt be perfect for any environment, but it might mean the difference between working a mult and not working a mult. And multipliers, after all, are :) As you said, every receiving environment is different, but some generalizations can be made and being able to recall the multiple settings would be a definite plus feature of the radio. Thanks for letting us test these iterations. Lu Romero - W4LT K3 # 3192 Lyle Johnson wrote: ...For now I'll treat the parameter as an opaque series of magic numbers. The way the new beta NR works is: Fx-y x selects the length of the filter. F1 = 121 taps, F2 = 91 taps, F3 = 61 taps, F4 = 31 taps (The Beta 3.25 release used FIR filters of 61 taps.) y selects values of Beta (gain), decay, and delay (how long the NR algorithm waits to process a signal) (The Beta 3.5 release used the x parameter for these selections) 73, Lyle KK7P ___ ___ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- View this message in context: http://n2.nabble.com/K3-NR-tp3515659p3520809.html Sent from the [K3] mailing list archive at Nabble.com. ___ ___ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] K3 NR triggering
Thanks for the nice explanation Bill. It is effective but weird. Somone needs to make a movie. Steve N4LQ n...@carolina.rr.com - Original Message - From: Bill W4ZV btipp...@alum.mit.edu To: elecraft@mailman.qth.net Sent: Thursday, August 27, 2009 7:12 AM Subject: Re: [Elecraft] [K3] K3 NR triggering Steve Ellington wrote: I just had a CW QSO on a noisy 80m. Here's what I noticed with NR set for F1-3. BW set for 2.5 kHz. QRN very loud! I pushed NR. Band goes almost totally silent. Calling CQ with the bug was like being in TX mode but I was using QSK as always. Wow...Nice and quiet. Then someone answered my CQ. On his very first DIT, the noise level jumped up and stayed up throughout the entire QSO. It was quieter than no NR at all but why should it stay that way??? Remember that NR is an adaptive filter. When you perturb it with a coherent signal it rebuilds the filter around that signal. F1 is the longest tap setting which means it has the greatest stored data stream and will take the longest to respond when you add new data (i.e. a signal). Once the new input to the filter (signal plus noise) is steady state, the filter will then stay in that state until the inputs change again (i.e. when the signal goes away). 73, Bill -- View this message in context: http://n2.nabble.com/K3-NR-triggering-tp3521099p3524344.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR in Ver 3.27
Do you have any RX EQ on? Is this CW or SSB? What bandwidth are you operating at? Have you tried with AFX on and off? Plenty of audio here. 73 Ian On 27 Aug 2009, at 27August13:00, Barry Simpson wrote: I have just installed 3.27 and the NR is a disaster. On turning it on there is virtually no AF output even at maximum AF gain setting. I have turned the K3 off and on but to no avail. Also there are big birdies on 40m (I haven't checked any other bands) which I am sure were not there before I upgraded from 3.25. Has anyone any ideas . If not it looks as if I will need to go back to 3.25. Barry VK2BJ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- Ian J Maude, G0VGS SysOp GB7MBC HB9DRV-9 DX Clusters Member RSGB, GQRP 9838, FISTS 14077 | K3 #455 http://www.amateurradiotraining.org __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR triggering
I also seem to get the impression that the selected NR setting is not exacty the same as the selected level within in the menu versus turning the DSP NR on and off without entering the menu, if that makes sense. The NR is an adaptive filter. When you turn it off, it is completely reset: all buffers are flushed and filter coefficients zeroed. When you move from setting to setting with the NR adjust feature, the buffers are not flushed nor are the coefficients reset. Instead, the new settings are applied to the current state of the filter. So, it takes from a few tens of milliseconds to perhaps a couple of seconds for the filter to adapt to the new settings. 73, Lyle KK7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR in Ver 3.27
I have just installed 3.27 and the NR is a disaster. On turning it on there is virtually no AF output even at maximum AF gain setting. I have turned the K3 off and on but to no avail. Were you tuned to a signal at the time, or just band noise? If just noise, then the NR was doing its job. Please start with setting F1-1. This is the lightest NR action. 73, Lyle KK7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR triggering
Lyle: Maybe a quick lesson on proper use of the NR filter would help us. Thinks likeIf F1-1 doesn't work, do we go to F1-2 or F2-1 or should we skip a few F's. Should we turn NR off then back on every time we make a change? Does changing NR settings while receiving a cw signal matter or should one change settings with no signal? I guess I got spoiled by the IC-7800's NR. With it, you just turn it on and the noise disappeared. Steve N4LQ n...@carolina.rr.com - Original Message - From: Lyle Johnson k...@wavecable.com To: Craig vk...@yahoo.com Cc: elecraft@mailman.qth.net Sent: Thursday, August 27, 2009 9:10 AM Subject: Re: [Elecraft] K3 NR triggering I also seem to get the impression that the selected NR setting is not exacty the same as the selected level within in the menu versus turning the DSP NR on and off without entering the menu, if that makes sense. The NR is an adaptive filter. When you turn it off, it is completely reset: all buffers are flushed and filter coefficients zeroed. When you move from setting to setting with the NR adjust feature, the buffers are not flushed nor are the coefficients reset. Instead, the new settings are applied to the current state of the filter. So, it takes from a few tens of milliseconds to perhaps a couple of seconds for the filter to adapt to the new settings. 73, Lyle KK7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR in Ver 3.27
I operate a lot on CW nets, with the b/w set to 700Hz, no EQ, AFX on, and use the NR to increase the apparent S/N ratio, and also to soften the effect of band noise on the ears. Before v3.25, this was frustrating because the NR took appreciable time to build the filter, and appeared to do so on each code element; the overall effect was to make the code sound mushy and harder to copy. Then v3.25 came along, and it made a big improvement. The mushiness was gone and by experimenting with the various settings, I could find a sweet point where the filters were not too aggressive and yet an appreciable improvement in copy was obtained. With v3.27, the filtering became even more focussed and this morning I used a 3-3 setting to pull weaker stations out of the noise on 40m, which was having one of it's less stellar days. I think the guys at Aptos are definitely going in the right direction, especially for the CW side of things. I've tried the NR on a couple of SSB nets, but there the improvement was less easy to pick out -- though I think it IS an improvement when you find the correct setting. Not a scientific review, just very subjective $.02 worth. 73, Van W1WCG __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR triggering
Thinks likeIf F1-1 doesn't work, do we go to F1-2 or F2-1 or should we skip a few F's. Depends on the noise, the signal, the levels and the nature of the artifacts of NR you best tolerate. F1-x builds sharper filters, while F4-x typically has more attenuation... Should we turn NR off then back on every time we make a change? It usually won't adapt any faster if you do. Does changing NR settings while receiving a cw signal matter or should one change settings with no signal? Since you are trying to maximize the intelligibility of the signal, I'd only adjust it if there is a signal. I normally leave mine at F1-1 unless there is a good reason to change it. But that is for my antenna (3 element SteppIR), noise level (rural), band (20m daytime), mode (SSB), AGC settings (default THR and SLP) and typical signals (weak to moderate) I encounter here. 73, Lyle KK7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR (what is the equiv to F3-1 from 3.25?)
hi... i'm one of the folks who is less happy with the 3.27 implementation of NR than the 3.25. i've been trying to do a 'scientific' comparison of the two, so i can record the audio and upload for others to hear/analyze (non trivial since band conditions and QSO's don't seem to last between loading of the FW) in any event, i'm listening right now to an LSB QSO on 7.182.50. receive EQ is totally flat, noise level here is about an S5. using 3.25, if i set the NR to F3-1, the noise drops down by about 50-75% and the audio peaks up (sharper/more intelligable) about 25% i then load 3.27 but can't find any settings that are similar... even F1-1 gives me a distinct ringing/echo (echo is not quite right... its more like the old spring reverb's of my youth!)... i think that F1-3 should at least match the taps of 3.25, but can i completely replicate the filter response of 3.25's F3-1? btw, i know there's a fair bit of multi-variable confusion and well, it works fine here, which is to be expected in beta testing... but given that (even with the small sample of this thread) folks seem to 'clump' into the two camps of works great and say what? i'm wondering if there's something else at play here? another bit of code that's specific to production run variation, or a change in the underlying DSP circuitry/programming during the life of the K3? lyle, is there, perhaps, a chart/form you could suggest for testing with some instructions (ie, make receive bandwidth flat, for SSB 40m, adjust bw/passband/etc., serial no of K3, etc?)... then those of us interested in more rigorous testing can provide some kind of unified feedback? i'm a beta tester for some other hw/sw consumer products and the reporting requirements usually establish a baseline so the engineers can look for patterns. (oh, and THANKS for all the hard work... if this were easy it wouldn't be half as much fun!) 73 robin (K9RDG) __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K3] firmware load failure
I had latest beta (3.27) loaded and thought I'd save the configuration. It failed with a prompt regarding EEPROM 000.013. I thought I'd reload the firmware again (3.27) but it stopped, saying that it couldn't load MCU. The K3 was frozen with MCU LD on VFO B and TX light flashing. It would not turn off. I restarted the Utility and got the same message. I turned off the power supply and when restarting the K3, it shows the same MCU LD on VFO B but the fans are running and the screen light is no longer lit. The is the first issue I've ever had with firmware loading. No of course the K3 is inoperable. The utility is (Mac 1.2.3.18) Couldn't see anything in the Troubleshooting section of the manual. Help Please! Gary W7TEA K3 (1001) -- View this message in context: http://n2.nabble.com/firmware-load-failure-tp3526724p3526724.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] firmware load failure
Gees. Thought I'd remember that it is almost always something simple. My logger program was also running. Dumb. Anyway, all fixed and apologize for the wasted bandwidth. Gary W7TEA W7TEA wrote: I had latest beta (3.27) loaded and thought I'd save the configuration. It failed with a prompt regarding EEPROM 000.013. I thought I'd reload the firmware again (3.27) but it stopped, saying that it couldn't load MCU. The K3 was frozen with MCU LD on VFO B and TX light flashing. It would not turn off. I restarted the Utility and got the same message. I turned off the power supply and when restarting the K3, it shows the same MCU LD on VFO B but the fans are running and the screen light is no longer lit. The is the first issue I've ever had with firmware loading. No of course the K3 is inoperable. The utility is (Mac 1.2.3.18) Couldn't see anything in the Troubleshooting section of the manual. Help Please! Gary W7TEA K3 (1001) -- View this message in context: http://n2.nabble.com/firmware-load-failure-tp3526724p3526834.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] firmware load failure
That will definitely cause a problem. :) Glad you got it going. Please ignore my off-list email. David, W4SMT --- On Thu, 8/27/09, W7TEA gt...@mac.com wrote: From: W7TEA gt...@mac.com Subject: Re: [Elecraft] [K3] firmware load failure To: elecraft@mailman.qth.net Date: Thursday, August 27, 2009, 10:52 AM Gees. Thought I'd remember that it is almost always something simple. My logger program was also running. Dumb. Anyway, all fixed and apologize for the wasted bandwidth. Gary W7TEA W7TEA wrote: I had latest beta (3.27) loaded and thought I'd save the configuration. It failed with a prompt regarding EEPROM 000.013. I thought I'd reload the firmware again (3.27) but it stopped, saying that it couldn't load MCU. The K3 was frozen with MCU LD on VFO B and TX light flashing. It would not turn off. I restarted the Utility and got the same message. I turned off the power supply and when restarting the K3, it shows the same MCU LD on VFO B but the fans are running and the screen light is no longer lit. The is the first issue I've ever had with firmware loading. No of course the K3 is inoperable. The utility is (Mac 1.2.3.18) Couldn't see anything in the Troubleshooting section of the manual. Help Please! Gary W7TEA K3 (1001) -- View this message in context: http://n2.nabble.com/firmware-load-failure-tp3526724p3526834.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] One last rehash on tuning hash
In answer to Joe Planisky, here's my rehash on hash. My K3 which is factory built still has some tuning hash but it's now at a much lower in level, doesn't move the s-meter (with or without preamp) and is only centered around 28000 +/- 5 KHz. I can barely hear it now. I haven't added the h/w mod. Because this K3 is factory built and never been opened, lets assume it is properly built with cables and fasteners properly positioned and seated. Eric's comment: The h/w mod does not really impact the noise at all. It is required though and is there to maintain reliable signaling between the main processor and the synthesizers when the CPU to Synct serial bus speed is increased with SPI=2. Its the change to SPI=2 that reduces the noise. I've read some conflicting comments on the need to make the h/w mod. I gather it's Eric's position that it's necessary to keep the signals clean between the main MCU and synthesiszers. Before seeing this latest comment I was left thinking the h/w mod would also further reduce the tuning hash. With all this in mind I can live with small amount of remaining tuning hash. And, this K3 has been running in this configuration for almost a month without any signs of problems that could relate to omitting the h/w part of change. Cheers to the Elecraft team. John, W1QS K3 s/n 2274 K2 s/n 4204 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR (what is the equiv to F3-1 from 3.25?)
I thought Lyle's email quoted below was very helpful: The way the new beta NR works is: Fx-y selects the length of the filter. F1 = 121 taps, F2 = 91 taps, F3 = 61 taps, F4 = 31 taps (The Beta 3.25 release used FIR filters of 61 taps.) y selects values of Beta (gain), decay, and delay (how long the NR algorithm waits to process a signal) (The Beta 3.5 release used the x parameter for these selections) 73, Lyle KK7P 73, Bill K9YEQ K2 #35; KX1 #35; K3 #1744; mini mods ATS-3B __ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] One last rehash on tuning hash
What Eric says is quite correct. Some of the confusion a few days ago was around the fact that I had completely different issue surface right after installing the hardware mod that suggested it was necessary to upgrade the firmware if the hardware mod is done. That's not true. The hardware mod simply equips the K3 to handle a faster bus rate that can be selected in the MENU with 3.24 or later firmware. The mod does not interfere with using the original bus rate. The faster bus rate reduces the tuning noise on the K3s tested. Normally, you'll need to remove the antenna or listen on a *very* quiet 6, 10, or 60 meter band to hear the VFO tuning noise. Don't forget there are other potential sources for noise, birdies, etc. Among them are loose/missing case screws (but don't over-tighten them - it doesn't help to make them tighter once they are firmly seated) and cables for the KRX3 subreceiver module not routed per the instructions. The KRX3 manual has details about the cable routing that must be observed for best results. It's worth checking these things if there are any sort of noises or birdies, especially if they seem to have gotten worse or suddenly appeared after working on your K3. One case screw that's often overlooked is on the side of the K3 near the forward end of the handle. It makes sure that side is held securely against the front panel shield inside. Ron AC7AC -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of John Lawrence Sent: Thursday, August 27, 2009 8:08 AM To: elecraft@mailman.qth.net Subject: [Elecraft] One last rehash on tuning hash In answer to Joe Planisky, here's my rehash on hash. My K3 which is factory built still has some tuning hash but it's now at a much lower in level, doesn't move the s-meter (with or without preamp) and is only centered around 28000 +/- 5 KHz. I can barely hear it now. I haven't added the h/w mod. Because this K3 is factory built and never been opened, lets assume it is properly built with cables and fasteners properly positioned and seated. Eric's comment: The h/w mod does not really impact the noise at all. It is required though and is there to maintain reliable signaling between the main processor and the synthesizers when the CPU to Synct serial bus speed is increased with SPI=2. Its the change to SPI=2 that reduces the noise. I've read some conflicting comments on the need to make the h/w mod. I gather it's Eric's position that it's necessary to keep the signals clean between the main MCU and synthesiszers. Before seeing this latest comment I was left thinking the h/w mod would also further reduce the tuning hash. With all this in mind I can live with small amount of remaining tuning hash. And, this K3 has been running in this configuration for almost a month without any signs of problems that could relate to omitting the h/w part of change. Cheers to the Elecraft team. John, W1QS K3 s/n 2274 K2 s/n 4204 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR
I loaded bata 3.27 yesterday have played with it on cw and ssb so far I like what I hear the NR is more to my liking adding the AFX is a nice touch to get the audio to pop out a bit. The bands are not the best here for me using a Hy Tower vertical as the only HF antenna I would say that 3.27 is an over all improvement so far as I see and hear it. Regards Art ka9zap Eric Swartz - WA6HHQ, Elecraft wrote: Hi Gary, Please remember that this is a -beta test- release and not a formal final K3 f/w release. The purpose of any beta test release is to test new features and gather constructive feedback. It is not something you should be using to form a final judgment or complain loudly about, sine we certainly will react to feedback on it and respond with follow on releases. That's the whole point of releasing a beta test release before making it final. It gives us real feedback from a much broader swath of users than we ever could get in the lab. Also, have no fear, we are working to provide the best NR out there for BOTH SSB and CW ops. That's why we are experimenting with it in these beta test releases. Stay tuned! And thanks to everyone for the constructive feedback. We really appreciate it. 73, Eric rfenab...@gmail.com wrote: Well the SSB folks lose out yet again on the latest FW revision. Just when the next to useless NR was made to work we have yet another version that favours one mode over others. Rather disappointing result but that appears to be the way of the k3 world at times. Great radio for some but so great for others perhaps..:-( Don't know could be a replacement but the search has started. Gary VK4WT __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] NR in the latest K3 firmware released yesterday
I find this to be a great improvement on SSB for weaker ones buried in the noise. With NR turned on to the F1-1 setting I could pull out the weak JAs and VK/ZLs this morning on 40 SSB. It truly works well without to much of the hollow in the tunnel reception. Turning up the NR settings beyond the first doesn't seem to offer improvement. On CW the improvement isn't that great unless I open up the bandwidth to the F1 SSB filter. With FL2 turned on to about 300 Hz the weak signal improvement isn't as pronounced as on SSB. I guess the question is to know if narrow band CW signals can expect the same level of improvement using any DSP NR algorithm? Also, the CW mode auto tune tap on SPOT is slick. I'll keep that. Nice going Lyle 73, John, W1QS K3 s/n 2274 K2 s/n 4204 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Looking for an XV50
Prefer unbuilt if you have one that sitten around drawing dust. Please e-mail direct ! Thanks and 73: JerryN0JRN __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR
Lyle, Is the noise reduction more or less aggressive with a larger number of taps (length) of the filter? 73, ... Joe, W4TV -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Lyle Johnson Sent: Wednesday, August 26, 2009 4:23 PM To: Bob Cunnings Cc: Elecraft Subject: Re: [Elecraft] K3 NR ...For now I'll treat the parameter as an opaque series of magic numbers. The way the new beta NR works is: Fx-y x selects the length of the filter. F1 = 121 taps, F2 = 91 taps, F3 = 61 taps, F4 = 31 taps (The Beta 3.25 release used FIR filters of 61 taps.) y selects values of Beta (gain), decay, and delay (how long the NR algorithm waits to process a signal) (The Beta 3.5 release used the x parameter for these selections) 73, Lyle KK7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR
Is the noise reduction more or less aggressive with a larger number of taps (length) of the filter? It is less aggressive with more taps. There is also a different coloring of the audio. 73, Lyle KK7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR (what is the equiv to F3-1 from 3.25?)
hi... thanks for the reply... yes, i read lyle's description of the two filters, which is how i knew that the 3.25 filters all had an FIR of 61 taps... what i'm looking for (in order do to an honest A:B comparison between 3.25 and 3.27 on my rig) is what Fx-y on 3.27 would most closely match the F3-1 configuration of 3.25 73 robin (K9RDG) Date: Thu, 27 Aug 2009 10:18:54 -0500 From: Bill k9...@live.com Subject: Re: [Elecraft] K3 NR (what is the equiv to F3-1 from 3.25?) To: elecraft@mailman.qth.net I thought Lyle's email quoted below was very helpful: The way the new beta NR works is: Fx-y selects the length of the filter. F1 = 121 taps, F2 = 91 taps, F3 = 61 taps, F4 = 31 taps (The Beta 3.25 release used FIR filters of 61 taps.) y selects values of Beta (gain), decay, and delay (how long the NR algorithm waits to process a signal) (The Beta 3.5 release used the x parameter for these selections) 73, Lyle KK7P 73, Bill K9YEQ K2 #35; KX1 #35; K3 #1744; mini mods ATS-3B __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] One last rehash on tuning hash
Hi John, This is not a personal position - Its official current Elecraft company policy. :-) To be totally clear, if you enable 'VCO MD, SPI 2 for the VFO noise reduction, you MUST ultimately make the corresponding h/w mod. Its OK to test without making the mod to see if 'SPI 2' helps your situation, but then you ultimately must do the h/w mod. Failure to do so, when using 'SPI 2', may cause your K3 frequency tuning to be unreliable at random times, depending upon a wide range of variables, including band, temperature, supply voltage, type and number of options installed etc. The display frequency will tune normally, but the actual Synthesizer frequency, may not always follow correctly. Of course, if the 'VCO MD, SPI' menu entry is left at the default of 'SPI 1', you do -not- need to make the h/w mod. (Note: regarding the confusion in this: Ron's original posting where he thought he had a problem turned out to be a red herring. Upon further investigation we found he had fast tuning turned -on- for his RIT control and was not aware of it. He was also seeing the actual freq display change on his K3, which was the result of bumping the RIT control in this mode with RIT=OFF. :-) 73, Eric WA6HHQ Elecraft John Lawrence wrote: In answer to Joe Planisky, here's my rehash on hash. My K3 which is factory built still has some tuning hash but it's now at a much lower in level, doesn't move the s-meter (with or without preamp) and is only centered around 28000 +/- 5 KHz. I can barely hear it now. I haven't added the h/w mod. Because this K3 is factory built and never been opened, lets assume it is properly built with cables and fasteners properly positioned and seated. Eric's comment: The h/w mod does not really impact the noise at all. It is required though and is there to maintain reliable signaling between the main processor and the synthesizers when the CPU to Synct serial bus speed is increased with SPI=2. Its the change to SPI=2 that reduces the noise. I've read some conflicting comments on the need to make the h/w mod. I gather it's Eric's position that it's necessary to keep the signals clean between the main MCU and synthesiszers. Before seeing this latest comment I was left thinking the h/w mod would also further reduce the tuning hash. With all this in mind I can live with small amount of remaining tuning hash. And, this K3 has been running in this configuration for almost a month without any signs of problems that could relate to omitting the h/w part of change. Cheers to the Elecraft team. John, W1QS __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 Shift
Hello All, I built S/N 1354 from a kit , with FW 3.25 , I have installed most of the mods. I operate digi modes some of the time and I need to set the shift to 1.25 instead of 1.50 to be centered in the IF strip. It's been this way ever since I built it. I'm not sure what I have setup wrong . All filters are 8 pole . With the new shift steps set to 10 hz the shift control knob needs to be set all the way to the left ( 1.28 ) to be centered. Also on 160 M when I rotate the RIT knob fast to change the frequency I have some kind of image, Not sure what this is ?? Thanks for your help 73 Ken K5DNL __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 NR triggering
It's become obvious to me that the most of the full time CW ops on the reflector were very happy with the fast responding, instant changing, very aggressive filters on the Pre 3.25 NR. So long as you didn't choose a filter that was too aggressive for your needs, I never found that I cut out any CW tones. As matter of fact, I found that with the old NR I was able to actually Enhance CW tones. I DO NOT find this to be the case with either 3.25, or 3.27. Without an Audio peak filter on the K3, I much prefer what I had previously. As a late night, high QRM 30meter DXer I find that I enjoyed the ability to switch between filter groups and hear the results instantaneously. Unlike SSB where you can wait that extra second, on CW, every dit and dah counts. Instead of trying to find a single NR DSP that would satisfy both groups, which seems near impossible to do. Wouldn't it be best to implement some way to have the OLD NR on CW mode, and then perhaps something like 3.25 or 3.27 on SSB mode? This way the CW guys, like myself, can enjoy the serious filter ability of the old NR, and the SSB guys can enjoy the pipeless artifacts when using NR in SSB mode. Some times you can't satisfy all the people all the time with one road. But you can send them in different directions and try to help them both at the same time. N6MQL _ Get back to school stuff for them and cashback for you. http://www.bing.com/cashback?form=MSHYCBpubl=WLHMTAGcrea=TEXT_MSHYCB_BackToSchool_Cashback_BTSCashback_1x1 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR triggering
FWIW, I strongly agree with N6MQL's suggestion. Bill W5WVO The Smiths (N6MQL) wrote: Instead of trying to find a single NR DSP that would satisfy both groups, which seems near impossible to do. Wouldn't it be best to implement some way to have the OLD NR on CW mode, and then perhaps something like 3.25 or 3.27 on SSB mode? This way the CW guys, like myself, can enjoy the serious filter ability of the old NR, and the SSB guys can enjoy the pipeless artifacts when using NR in SSB mode. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Shift
Hi Ken. You can save two unique filter setups using the NORM knob. 1. First, hold NORM to clear any shift to give you a good starting point. 2. Now set desired WIDTH and SHIFT the FC to where you want it. 3. Now do a LONG HOLD of the NORM knob till you see SAVE. Rotate the knob while you have it pressed to the left to save your custome filter to setting 1. 4. Do the same process and rotate to the knob to the RIGHT to save setting 2. I do this for SSTV and PSK. Its a quick and easy way to recall a custome filter for digital modes. Also, If you use DXLabs (and I believe others can do this as well but its very easy in DXL) you can enter CAT commands by mode. So when I use WinWarbler and select PSK it automatically sets the shift and the BW, and power output to what I want. No need to go to the radio to make any changes. It just happens. Hope this helps! - 73, Greg - AB7R Whidbey Island WA NA-065 On Thu Aug 27 10:51 , Ken Roberson sent: Hello All, I built S/N 1354 from a kit , with FW 3.25 , I have installed most of the mods. I operate digi modes some of the time and I need to set the shift to 1.25 instead of 1.50 to be centered in the IF strip. It's been this way ever since I built it. I'm not sure what I have setup wrong . All filters are 8 pole . With the new shift steps set to 10 hz the shift control knob needs to be set all the way to the left ( 1.28 ) to be centered. Also on 160 M when I rotate the RIT knob fast to change the frequency I have some kind of image, Not sure what this is ?? Thanks for your help 73 Ken K5DNL __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: Elecraft@mailman.qth.net','','','')Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K3] Unable to perform opt.3 callibration for 1ppm xtal
Hi, I have the 1 ppm xtal and want to do the #3 callibration option. I've read the book and checked what I was doing several times. I also have the latest firmware (3.27 beta) installed. I keep pushing 1 and I don't get the REF xxCAL, it just doesn't seem to be an option. What am I missing? Suggestions... -- View this message in context: http://n2.nabble.com/Unable-to-perform-opt-3-callibration-for-1ppm-xtal-tp3529355p3529355.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] Unable to perform opt.3 callibration for 1ppm xtal
That feature hasn't been implemented yet. 73 de James K2QI On Thu, Aug 27, 2009 at 3:14 PM, 4Z5TO 4z...@iarc.org wrote: Hi, I have the 1 ppm xtal and want to do the #3 callibration option. I've read the book and checked what I was doing several times. I also have the latest firmware (3.27 beta) installed. I keep pushing 1 and I don't get the REF xxCAL, it just doesn't seem to be an option. What am I missing? Suggestions... -- View this message in context: http://n2.nabble.com/Unable-to-perform-opt-3-callibration-for-1ppm-xtal-tp3529355p3529355.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- 73 de James K2QI __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR triggering
Some times you can't satisfy all the people all the time with one road. Truer words were never spoken! I'm a full time CW operator (well, 99.9% CW, 0.1% digital modes.) I played with the pre-3.25 NR quite a bit and I was never able to find a setting that made a CW signal easier to copy, so I never actually used it in a QSO. Post-3.25, I find I'm now using it more often than not. My preference would be for progress to continue in the 3.25/3.27 direction. Of course, ideally they'll come up with a way to let each operator use what works best for them. 73 -- Joe KB8AP On Aug 27, 2009, at 11:18 AM, The Smiths wrote: It's become obvious to me that the most of the full time CW ops on the reflector were very happy with the fast responding, instant changing, very aggressive filters on the Pre 3.25 NR. So long as you didn't choose a filter that was too aggressive for your needs, I never found that I cut out any CW tones. As matter of fact, I found that with the old NR I was able to actually Enhance CW tones. I DO NOT find this to be the case with either 3.25, or 3.27. Without an Audio peak filter on the K3, I much prefer what I had previously. As a late night, high QRM 30meter DXer I find that I enjoyed the ability to switch between filter groups and hear the results instantaneously. Unlike SSB where you can wait that extra second, on CW, every dit and dah counts. Instead of trying to find a single NR DSP that would satisfy both groups, which seems near impossible to do. Wouldn't it be best to implement some way to have the OLD NR on CW mode, and then perhaps something like 3.25 or 3.27 on SSB mode? This way the CW guys, like myself, can enjoy the serious filter ability of the old NR, and the SSB guys can enjoy the pipeless artifacts when using NR in SSB mode. Some times you can't satisfy all the people all the time with one road. But you can send them in different directions and try to help them both at the same time. N6MQL __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] Unable to perform opt.3 callibration for 1ppm xtal
Thanks. I'm 2 for 2 now. Where did I miss that? Ok folks, nothing to see here. Move along... K2QI wrote: That feature hasn't been implemented yet. 73 de James K2QI On Thu, Aug 27, 2009 at 3:14 PM, 4Z5TO 4z...@iarc.org wrote: Hi, I have the 1 ppm xtal and want to do the #3 callibration option. I've read the book and checked what I was doing several times. I also have the latest firmware (3.27 beta) installed. I keep pushing 1 and I don't get the REF xxCAL, it just doesn't seem to be an option. What am I missing? Suggestions... -- View this message in context: http://n2.nabble.com/Unable-to-perform-opt-3-callibration-for-1ppm-xtal-tp3529355p3529355.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- 73 de James K2QI __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- View this message in context: http://n2.nabble.com/Unable-to-perform-opt-3-callibration-for-1ppm-xtal-tp3529355p3529459.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] New K2 build - encoder problem
If you haven't already found the problem. Another thing you can check is U2. With the rig off, 3,4,5,6 11,12,13,14 should all read 100K ohms to VCC pin(18) With the rig on, these should all normally be at VCC voltage. -- bw...@fastmail.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K2 Noise Blanker Problem
I built my K2 some months back with the KNB2 option. The noise blanker has never been effective against any type of noise. The MCU recognizes the blanker, it draws the proper amount of current, but just doesn't seem to do anything. Before drinking the Kool-Aid (TM) I was pretty much a Kenwood man and was used to ineffective noise blankers so I ended up blowing it off. I recently built a K1, and the NB in it works FB. This got me thinking, and besides Elecraft would never release a NB that was useless--it violates the Tao of Elecraft. Yesterday I built another KNB2 (any excuse) and installed it in my K2. Same result! I checked all the solder joints, component values, RF board mods. It makes no difference whether it is NB1, NB2, HI or LO, the preamp is on or off--nothing. No change in S-meter reading, no change in audio. Any ideas, oh mighty brains? Thanks, Eric WD6DB(lost in noise) __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K2 Noise Blanker Problem
I built my K2 some months back with the KNB2 option. The noise blanker has never been effective against any type of noise. The MCU recognizes the blanker, it draws the proper amount of current, but just doesn't seem to do anything. Before drinking the Kool-Aid (TM) I was pretty much a Kenwood man and was used to ineffective noise blankers so I ended up blowing it off. I recently built a K1, and the NB in it works FB. This got me thinking, and besides Elecraft would never release a NB that was useless--it violates the Tao of Elecraft. Yesterday I built another KNB2 (any excuse) and installed it in my K2. Same result! I checked all the solder joints, component values, RF board mods. It makes no difference whether it is NB1, NB2, HI or LO, the preamp is on or off--nothing. No change in S-meter reading, no change in audio. Any ideas, oh mighty brains? Thanks, Eric WD6DB(lost in noise) __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K2 Noise Blanker Problem
I built my K2 some months back with the KNB2 option. The noise blanker has never been effective against any type of noise. The MCU recognizes the blanker, it draws the proper amount of current, but just doesn't seem to do anything. Before drinking the Kool-Aid (TM) I was pretty much a Kenwood man and was used to ineffective noise blankers so I ended up blowing it off. I recently built a K1, and the NB in it works FB. This got me thinking, and besides Elecraft would never release a NB that was useless--it violates the Tao of Elecraft. Yesterday I built another KNB2 (any excuse) and installed it in my K2. Same result! I checked all the solder joints, component values, RF board mods. It makes no difference whether it is NB1, NB2, HI or LO, the preamp is on or off--nothing. No change in S-meter reading, no change in audio. Any ideas, oh mighty brains? Thanks, Eric WD6DB(lost in noise) __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR - Audio Artifact on Button Press F1-x (Beta 3.27)
ok... this is something that other folks can absolutely test (grin) i have audio feedback (button beeps) turned on in my K3 and i've been playing with the 3.25 and 3.27 beta's i just noticed that with 3.27 that when i either 'turn on' or 'turn off' (momentary press) or long-press the NR button and the filter is set to either F1-1, F1-2, F1-3 or F1-4, the button beep is not a clean beep sound (sine wave?) but a little 'dirty' like there are some overtone/harmonics mixed in... you can possibly hear this through the speak, if you have great hearing, but it is very obvious with headphones (i'm using the sony mdr-v6) if you set the filter to F2-x, or F3-x, then the beep is perfectly clean and sweet (like a stravinsky concerto!) extra wrinkle... i have NB off but had NOTCH set to auto... turning the notch filter off or to manual seems to 'change' this behaviour, but not in a predictable way... with the notch filter off the button beeps are clean (i think) but sometimes turning the notch back on makes the beeps dirty again, and sometimes not... wish i could be more clear. btw, i'm doing all this testing with the audio level down to zero, listening through phones to just the beeps (yah, sometimes that's safer than trying to call CQ) some kind of interaction in the DSP between the NR code and NOTCH code? wondering if anyone else can repeat this and, if so, are you having success with the new 3.27 NR modes in SSB? many thanks to anyone who can do this test! 73 robin (K9RDG) __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR triggering
I would like to still see some kind of APF filter to peak up weak cw, I'm still always looking for more volume or gain against the noise floor. For me its hard to compare something from a couple of months ago to what I have now in firmware but for the impressions or notes taken back with other firmware set ups, with varying band conditions I really can't tell unless you had two radios side by side to compare in real time both on the same antenna at the same time with no a/b switching. Out of 4 cw attempts at my daily cw fix only one had enough level of volume s/n that was a comfortable arm chair copy, another fellow K3 owner at a camp ground in Mo. I would go for the dual firmware one for CW and the other for SSB also, 3.27 does well on SSB with the audio response, so far I like it a lot. Regards Art ka9zap Some times you can't satisfy all the people all the time with one road. Truer words were never spoken! I'm a full time CW operator (well, 99.9% CW, 0.1% digital modes.) I played with the pre-3.25 NR quite a bit and I was never able to find a setting that made a CW signal easier to copy, so I never actually used it in a QSO. Post-3.25, I find I'm now using it more often than not. My preference would be for progress to continue in the 3.25/3.27 direction. Of course, ideally they'll come up with a way to let each operator use what works best for them. 73 -- Joe KB8AP On Aug 27, 2009, at 11:18 AM, The Smiths wrote: It's become obvious to me that the most of the full time CW ops on the reflector were very happy with the fast responding, instant changing, very aggressive filters on the Pre 3.25 NR. So long as you didn't choose a filter that was too aggressive for your needs, I never found that I cut out any CW tones. As matter of fact, I found that with the old NR I was able to actually Enhance CW tones. I DO NOT find this to be the case with either 3.25, or 3.27. Without an Audio peak filter on the K3, I much prefer what I had previously. As a late night, high QRM 30meter DXer I find that I enjoyed the ability to switch between filter groups and hear the results instantaneously. Unlike SSB where you can wait that extra second, on CW, every dit and dah counts. Instead of trying to find a single NR DSP that would satisfy both groups, which seems near impossible to do. Wouldn't it be best to implement some way to have the OLD NR on CW mode, and then perhaps something like 3.25 or 3.27 on SSB mode? This way the CW guys, like myself, can enjoy the serious filter ability of the old NR, and the SSB guys can enjoy the pipeless artifacts when using NR in SSB mode. Some times you can't satisfy all the people all the time with one road. But you can send them in different directions and try to help them both at the same time. N6MQL __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Installing New Mods in K3
I have just installed the K3 VFO Tuning Noise Reduction mod and the K3 Automatic Front-End Protection mod in my newest K3. The mods went in well, but on the NoiseTuning Reduction mod, I did find the two vias on the left (viewing the RF board from the bottom) full of solder. I cut the 470 ohm resistor and soldered it in the proper via. I then cut the 1N4148 and soldered the anode in the proper via. The loose ends of these components were then cut and soldered together. Regarding the Automatic Front-End mod, be careful not to use too much solder on the right end of R56. I did, and created a bridge to the adjacent via. I had to use my desoldering gun to remove the excess solder. Now for the good news. While making these mods, I noticed that the KRX3 Subout Connector mod will be easily accessable. It is located under the bottom front panel same as the above mods. R8 is located on the right central part of the exposed RF board. The SMD resistor should not be hard to replace. I presume Elecraft will make this resistor available. Maybe it will be included in the P3 kit. Roy Morris W4WFB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Load failure on DSP v
I am getting the following failure to load the latest firmware. To get the load complete I tried sending only the new firmware. After several attempts in each of the DSP loads, the data was finally accepted. Any ideas as to what might be the cause... This is not the first time the difficulty was experience. Could a full reset and reload remove any corrupt resident software or is that accomplished with each firmware update? 13:55:11 K3 Utility Version 1.2.8.10 13:55:11 OS Version 5.1 Build 2600 Windows XP 13:58:56 Opening connection to ftp.elecraft.com 13:58:56 InternetConnect completed with error 12029: A connection with the server could not be established 13:58:56 Ready 13:58:57 K3 MCU version 03.25. COM3 RS-232 speed 38400 bps 13:59:02 Opening connection to ftp.elecraft.com 13:59:04 Copying files to C:\Documents and Settings\Bill\Application Data\Elecraft\BetaTest\k3fw3r25 13:59:05 Copied K3UtilityVersionInfo.txt from Elecraft 13:59:05 Copied 1 files from Elecraft to C:\Documents and Settings\Bill\Application Data\Elecraft\BetaTest\k3fw3r25 13:59:05 Ready 13:59:05 K3 MCU version 03.25. COM3 RS-232 speed 38400 bps 14:02:47 Opening connection to ftp.elecraft.com 14:02:51 Cancel Button completed with error 1223: The operation was canceled by the user. 14:02:51 Ready 14:02:52 K3 MCU version 03.25. COM3 RS-232 speed 38400 bps 14:03:15 Sending firmware file hmcu0327.hex to MCU 14:04:24 Loaded MCU firmware version 03.27. Radio responded with version 03.27 14:04:24 MCU firmware load is complete 14:04:28 Sending firmware file hfpf0102.hex to FPF 14:05:14 Loaded FPF firmware version 01.02. Radio responded with version 01.02 14:05:14 FPF firmware load is complete 14:05:15 Sending firmware file TBOOT7.HEX to DSP1 14:05:17 Sending firmware file hdsp0224.hex to DSP1 14:05:53 Sending firmware file DTBL0011.HEX to DSP1 14:07:49 Loaded DSP1 firmware version 02.24. Radio responded with version 02.21 14:07:49 DSP1 firmware load failed 17:00:51 Ready 17:00:51 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:01:08 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:01:40 Sending firmware file hmcu0327.hex to MCU 17:02:49 Loaded MCU firmware version 03.27. Radio responded with version 03.27 17:02:49 MCU firmware load is complete 17:02:53 Sending firmware file hfpf0102.hex to FPF 17:03:39 Loaded FPF firmware version 01.02. Radio responded with version 01.02 17:03:39 FPF firmware load is complete 17:03:40 Sending firmware file TBOOT7.HEX to DSP1 17:03:42 Sending firmware file hdsp0224.hex to DSP1 17:04:18 Sending firmware file DTBL0011.HEX to DSP1 17:06:14 Loaded DSP1 firmware version 02.24. Radio responded with version 02.21 17:06:14 DSP1 firmware load failed 17:08:08 Ready 17:08:08 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:09:54 K3 Utility Version 1.2.8.10 17:09:54 OS Version 5.1 Build 2600 Windows XP 17:09:54 Serial Port COM3 is open 17:09:54 Polling K3 17:09:55 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:10:27 Sending firmware file hmcu0327.hex to MCU 17:11:35 Loaded MCU firmware version 03.27. Radio responded with version 03.27 17:11:35 MCU firmware load is complete 17:11:39 Sending firmware file hfpf0102.hex to FPF 17:12:25 Loaded FPF firmware version 01.02. Radio responded with version 01.02 17:12:25 FPF firmware load is complete 17:12:26 Sending firmware file TBOOT7.HEX to DSP1 17:12:28 Sending firmware file hdsp0224.hex to DSP1 17:13:05 Sending firmware file DTBL0011.HEX to DSP1 17:15:01 Loaded DSP1 firmware version 02.24. Radio responded with version 02.21 17:15:01 DSP1 firmware load failed 17:15:15 Ready 17:15:15 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:15:28 Sending firmware file TBOOT7.HEX to DSP1 17:15:30 Sending firmware file hdsp0224.hex to DSP1 17:16:06 Sending firmware file DTBL0011.HEX to DSP1 17:18:02 Loaded DSP1 firmware version 02.24. Radio responded with version 02.24 17:18:02 DSP1 firmware load is complete 17:18:03 Sending firmware file TBOOT7.HEX to DSP2 17:18:05 Sending firmware file haux0224.hex to DSP2 17:18:41 Sending firmware file DTBL0011.HEX to DSP2 17:20:37 Loaded DSP2 firmware version 02.24. Radio responded with version 02.21 17:20:37 DSP2 firmware load failed 17:29:55 Ready 17:29:55 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:30:14 Sending firmware file TBOOT7.HEX to DSP2 17:30:16 Sending firmware file haux0224.hex to DSP2 17:30:51 Sending firmware file DTBL0011.HEX to DSP2 17:32:49 Loaded DSP2 firmware version 02.24. Radio responded with version 02.24 17:32:49 DSP2 firmware load is complete 17:32:49 Ready 17:32:49 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 73, Bill K9YEQ K2 #35; KX1 #35; K3 #1744; mini mods ATS-3B __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list:
[Elecraft] Correction - K3 IF Output Buffer Gain Mod
In a previous email I referred to the mod changing R8 on the RF board as the KRX3 SubOut Connector mod. I was referring to the K3 IF Output Buffer Gain mod. Sorry for the mistake. Roy Morris W4WFB __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 NR triggering
Joe and all, As I understand the changes, in the pre-3.27 NR situation, there were audio peaks in the response envelope - so it worked very well (similar to an APF) for some who used a CW pitch near the peaks, but there were others who used other sidetone pitches and they were not happy with the CW NR at all. The peaking in the response made SSB NR unusable for me, but now it enhances the signal while getting rid of the noise - Yes, I hear a bit of 'hollowness', but that is acceptable to me - at least I can hear and understand SSB signals down near the noise level. The key to finding the right NR settings is to adjust them while listening to a signal - if there is no signal, any of the NR settings can reduce the noise, but it may not be a setting that is suitable for the band conditions, antenna, noise type or signal strength. With 3.27 on 20 meters at my location, I use F1-x through F2-4 on SSB, but the F3-x and F4-x give me some signal attenuation - many CW operators have reported that F3-x and F4-x work well for them on CW. Experiment with it a bit, but do it while listening to the weakest signal that you wish to hear, and you should be able to find what will work best for you under those band and noise conditions. 73, Don W3FPR Joe Planisky wrote: Some times you can't satisfy all the people all the time with one road. Truer words were never spoken! I'm a full time CW operator (well, 99.9% CW, 0.1% digital modes.) I played with the pre-3.25 NR quite a bit and I was never able to find a setting that made a CW signal easier to copy, so I never actually used it in a QSO. Post-3.25, I find I'm now using it more often than not. My preference would be for progress to continue in the 3.25/3.27 direction. Of course, ideally they'll come up with a way to let each operator use what works best for them. 73 -- Joe KB8AP __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 headphone config question
I want to listen to my K3 with stereo headphones only. However if I unplug my headphones, I'd like the internal speaker to turn on. I studied this in the manual and am still not clear. This is the way my CONFIG is set up: CONFIG:SPKRS 2 CONFIG:SPKR+PH no Is this correct? Paul N4LCD __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 headphone config question
I want to listen to my K3 with stereo headphones only. However if I unplug my headphones, I'd like the internal speaker to turn on. I studied this in the manual and am still not clear. This is the way my CONFIG is set up: CONFIG:SPKRS 2 CONFIG:SPKR+PH no Is this correct? That will work. If you have a subrx installed, you can set SPKRS 1 so you'll hear it when you unplug the headphones. 73, Lyle KK7P __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K2 Noise Blanker Problem
Eric, First do a test to see if your NB is working at all. Remove the antenna, turn on the Preamp, then tap on the case of Q21 with a screwdriver. The taps will create impulse noise in the receiver which should be blanked when NB1 or NB2 is turned on. Be careful to differentiate between the clicks from the impulse noise and the rush of 'antenna/band noise' that happens because the screwdriver shaft can act as an antenna. If you find the NB is responding to that test, but it still does not help with your noise source, you can try widening the gate time a bit - try adding an additional .001 uF capacitor in parallel with C11 (just soleder ti to the solder pads for a test - if that helps, you can either leave the parallel cpacitor in place or change C11 to .002 uF. Other values may help as well, so some experimentation may be of help. If the noise gate is widened too much you will begin to notice holes on the received signal. 73, Don W3FPR eric norris wrote: I built my K2 some months back with the KNB2 option. The noise blanker has never been effective against any type of noise. The MCU recognizes the blanker, it draws the proper amount of current, but just doesn't seem to do anything. Before drinking the Kool-Aid (TM) I was pretty much a Kenwood man and was used to ineffective noise blankers so I ended up blowing it off. I recently built a K1, and the NB in it works FB. This got me thinking, and besides Elecraft would never release a NB that was useless--it violates the Tao of Elecraft. Yesterday I built another KNB2 (any excuse) and installed it in my K2. Same result! I checked all the solder joints, component values, RF board mods. It makes no difference whether it is NB1, NB2, HI or LO, the preamp is on or off--nothing. No change in S-meter reading, no change in audio. Any ideas, oh mighty brains? Thanks, Eric WD6DB(lost in noise) __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html No virus found in this incoming message. Checked by AVG - www.avg.com Version: 8.5.409 / Virus Database: 270.13.70/2329 - Release Date: 08/27/09 08:11:00 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [K3] firmware load failure
Same thing happened here until I discovered I still had my virtual port splitter running. Scared the heck out of me but all is well now. Funny how those ports have to be correct! David Fleming-2 wrote: That will definitely cause a problem. :) Glad you got it going. Please ignore my off-list email. David, W4SMT --- On Thu, 8/27/09, W7TEA gt...@mac.com wrote: From: W7TEA gt...@mac.com Subject: Re: [Elecraft] [K3] firmware load failure To: elecraft@mailman.qth.net Date: Thursday, August 27, 2009, 10:52 AM Gees. Thought I'd remember that it is almost always something simple. My logger program was also running. Dumb. Anyway, all fixed and apologize for the wasted bandwidth. Gary W7TEA W7TEA wrote: I had latest beta (3.27) loaded and thought I'd save the configuration. It failed with a prompt regarding EEPROM 000.013. I thought I'd reload the firmware again (3.27) but it stopped, saying that it couldn't load MCU. The K3 was frozen with MCU LD on VFO B and TX light flashing. It would not turn off. I restarted the Utility and got the same message. I turned off the power supply and when restarting the K3, it shows the same MCU LD on VFO B but the fans are running and the screen light is no longer lit. The is the first issue I've ever had with firmware loading. No of course the K3 is inoperable. The utility is (Mac 1.2.3.18) Couldn't see anything in the Troubleshooting section of the manual. Help Please! Gary W7TEA K3 (1001) -- View this message in context: http://n2.nabble.com/firmware-load-failure-tp3526724p3526834.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html -- View this message in context: http://n2.nabble.com/firmware-load-failure-tp3526724p3531254.html Sent from the [K3] mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] October QST Product Review: Flex 3K
QST's Product Review of the Flex-3000 is available to ARRL members at: http://www.arrl.org/members-only/prodrev/pdf/pr0910.pdf It's an interesting exercise to drag the Key Measurement Summary next to the K3 and Flex 5K models. Wide and narrow blocking gain compression shows about 10dB worse than the Flex 5K, and almost 30 dB worse than the K3. The following note in the Key section caught my eye: Blocking level exceeds the threshold of ADC clippng. Paul, W9AC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Load failure on DSP v
Sorry you are having this experience, Bill. Could you turn Verbise mode on and send me the loader dialog of the failing DSP1 load. The utility should leave the dialog open on failing loads so that you can copy the text into an email TU Dick, K6KR Sent from my iPhone On Aug 27, 2009, at 3:38 PM, Bill k9...@live.com wrote: I am getting the following failure to load the latest firmware. To get the load complete I tried sending only the new firmware. After several attempts in each of the DSP loads, the data was finally accepted. Any ideas as to what might be the cause... This is not the first time the difficulty was experience. Could a full reset and reload remove any corrupt resident software or is that accomplished with each firmware update? 13:55:11 K3 Utility Version 1.2.8.10 13:55:11 OS Version 5.1 Build 2600 Windows XP 13:58:56 Opening connection to ftp.elecraft.com 13:58:56 InternetConnect completed with 12029: A connection with the server could not be established 13:58:56 Ready 13:58:57 K3 MCU version 03.25. COM3 RS-232 speed 38400 bps 13:59:02 Opening connection to ftp.elecraft.com 13:59:04 Copying files to C:\Documents and Settings\Bill\Application Data\Elecraft\BetaTest\k3fw3r25 13:59:05 Copied K3UtilityVersionInfo.txt from Elecraft 13:59:05 Copied 1 files from Elecraft to C:\Documents and Settings\Bill\Application Data\Elecraft\BetaTest\k3fw3r25 13:59:05 Ready 13:59:05 K3 MCU version 03.25. COM3 RS-232 speed 38400 bps 14:02:47 Opening connection to ftp.elecraft.com 14:02:51 Cancel Button completed with error 1223: The operation was canceled by the user. 14:02:51 Ready 14:02:52 K3 MCU version 03.25. COM3 RS-232 speed 38400 bps 14:03:15 Sending firmware file hmcu0327.hex to MCU 14:04:24 Loaded MCU firmware version 03.27. Radio responded with version 03.27 14:04:24 MCU firmware load is complete 14:04:28 Sending firmware file hfpf0102.hex to FPF 14:05:14 Loaded FPF firmware version 01.02. Radio responded with version 01.02 14:05:14 FPF firmware load is complete 14:05:15 Sending firmware file TBOOT7.HEX to DSP1 14:05:17 Sending firmware file hdsp0224.hex to DSP1 14:05:53 Sending firmware file DTBL0011.HEX to DSP1 14:07:49 Loaded DSP1 firmware version 02.24. Radio responded with version 02.21 14:07:49 DSP1 firmware load failed 17:00:51 Ready 17:00:51 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:01:08 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:01:40 Sending firmware file hmcu0327.hex to MCU 17:02:49 Loaded MCU firmware version 03.27. Radio responded with version 03.27 17:02:49 MCU firmware load is complete 17:02:53 Sending firmware file hfpf0102.hex to FPF 17:03:39 Loaded FPF firmware version 01.02. Radio responded with version 01.02 17:03:39 FPF firmware load is complete 17:03:40 Sending firmware file TBOOT7.HEX to DSP1 17:03:42 Sending firmware file hdsp0224.hex to DSP1 17:04:18 Sending firmware file DTBL0011.HEX to DSP1 17:06:14 Loaded DSP1 firmware version 02.24. Radio responded with version 02.21 17:06:14 DSP1 firmware load failed 17:08:08 Ready 17:08:08 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:09:54 K3 Utility Version 1.2.8.10 17:09:54 OS Version 5.1 Build 2600 Windows XP 17:09:54 Serial Port COM3 is open 17:09:54 Polling K3 17:09:55 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:10:27 Sending firmware file hmcu0327.hex to MCU 17:11:35 Loaded MCU firmware version 03.27. Radio responded with version 03.27 17:11:35 MCU firmware load is complete 17:11:39 Sending firmware file hfpf0102.hex to FPF 17:12:25 Loaded FPF firmware version 01.02. Radio responded with version 01.02 17:12:25 FPF firmware load is complete 17:12:26 Sending firmware file TBOOT7.HEX to DSP1 17:12:28 Sending firmware file hdsp0224.hex to DSP1 17:13:05 Sending firmware file DTBL0011.HEX to DSP1 17:15:01 Loaded DSP1 firmware version 02.24. Radio responded with version 02.21 17:15:01 DSP1 firmware load failed 17:15:15 Ready 17:15:15 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:15:28 Sending firmware file TBOOT7.HEX to DSP1 17:15:30 Sending firmware file hdsp0224.hex to DSP1 17:16:06 Sending firmware file DTBL0011.HEX to DSP1 17:18:02 Loaded DSP1 firmware version 02.24. Radio responded with version 02.24 17:18:02 DSP1 firmware load is complete 17:18:03 Sending firmware file TBOOT7.HEX to DSP2 17:18:05 Sending firmware file haux0224.hex to DSP2 17:18:41 Sending firmware file DTBL0011.HEX to DSP2 17:20:37 Loaded DSP2 firmware version 02.24. Radio responded with version 02.21 17:20:37 DSP2 firmware load failed 17:29:55 Ready 17:29:55 K3 MCU version 03.27. COM3 RS-232 speed 38400 bps 17:30:14 Sending firmware file TBOOT7.HEX to DSP2 17:30:16 Sending firmware file haux0224.hex to DSP2 17:30:51 Sending firmware file DTBL0011.HEX to DSP2 17:32:49 Loaded DSP2 firmware version 02.24. Radio responded with version 02.24 17:32:49 DSP2 firmware load is complete 17:32:49 Ready
[Elecraft] 3.27 NR Works fine here
Hi Guys, I have just upgraded to the latest Beta release, using the new NR algorithm. In my opinion, it is the best it has ever been ! My only qualifier...I only operate SSB mode. 73 Glenn VK4BG __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K2 - Connecting the K2 to a RigBlaster Pro and computer
Evening All I think it's time for a bit more of the combined wisdom of the list before I proceed. The rig is a K2. It has all the internal modules except the ATU at this point. I have successfully used both HRD and K2 Remote to control the K2. The RigBlaster Pro is several years old. It was connected to an Icom - 706 until tonight, but only really used for PSK31 with Digipan. P1, the mic jumper block has been reconfigured to the K2. And an on air test was satisfactory. It's now time to configure P16 for Rig Ctl, CW, PTT, FSK, etc. I believe that diagram #9 on page 29 of my manual is the correct configuration. Then the 232 cables would be compter to RigBlaster 232-A, and RigBlaster 232-B to K2. Is this correct? And finally, what experience do others have in connecting and using the K2 with a RigBlaster? Any recommendations on other hookups that work best? Maybe some that aren't obvious? TNX to All de KD0R David __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] W2 Watt meter
Hi Everybody; It sure would be nice to take a peak at the W2 manual especially since it is listed as shipping sometime between 2009-08/30 and 09/07. 73's, Bob K7HBG __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] W2 Watt meter
We're working on it right now. I'll post a preliminary version as soon as we have it. 73, Eric --- k7hbg @dslextreme.com wrote: Hi Everybody; It sure would be nice to take a peak at the W2 manual especially since it is listed as shipping sometime between 2009-08/30 and 09/07. 73's, Bob K7HBG __ _..._ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] 3.27 NR Works fine here
hi glenn... since i'm one of the SSB operating folks who is having problems with 3.27 NR (but not 3.25) i'm wondering if you might answer some questions: 1. can you tell me your rig serial no/when it was mfg 2. what setting(s) are you using under NR and do you have AGC Fast or AGC Slow? 3. without NR on, what's the background noise S-level, and how much above that (if any) is the audio signal you're trying to pull out 4. are you using the 2.7 or 2.8khz roofing filter 5. what settings do you have BW/SHIFT/Hi/Low set at 6. when you turn NR on, what do you hear? (instant clean audio or a slow build-up? any echo effects or other audible artifacts?) 7. are you listening through the internal speaker/external speaker/phones and if stereo, do you have AFX on (and what setting) 8. have you altered your factory AGC settings under CONFIG from the defaults and if so, what settings are you using? 9. are you using a flat RX eq curve, or have you made any changes? 10. there is no question 10. i'm being a pain in the ss i know, so many thanks in advance for any info you can provide (and anyone else who is liking/loving 3.27 for SSB if you could answer these questions, that'd be great too!) 73, Glenn! robin (K9RDG) Hi Guys, I have just upgraded to the latest Beta release, using the new NR algorithm. In my opinion, it is the best it has ever been ! My only qualifier...I only operate SSB mode. 73 Glenn VK4BG __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] NR for Dummys
Where can I buy the book? Let's start with SSB on 3.27 (for me at this time). Will somebody send me the non-factory settings you have changed and what you have them set to that give you the what you see as the best setting (at any particular instant). I know this will change by conditions, antenna, location, etc. BUT, I would like somewhere to start AND have an idea which settings you change that help you in addition to the NR settings. Is this impossible? Huge thanks, 73, de Jim KG0KP __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html