Re: [OSL | CCIE_Voice] call disconnected after couple of seconds, cannot hear any thing when picked up.
Hi Sergio, You r the man, Tanx it solves the problem and works like a charm. Regards, Jeremy On Tue, Oct 21, 2008 at 7:58 AM, Sergio Polizer [EMAIL PROTECTED]wrote: Jeremy, Check if your MC3810 requires no use-proxy FXSZONE default inbound-to terminal under gatekeeper configuration. It worked for me with a ATA (h323) for calls *from* CallManager. HTH Sergio. -- Date: Sat, 18 Oct 2008 14:50:03 +1100 From: [EMAIL PROTECTED] To: [EMAIL PROTECTED] CC: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] call disconnected after couple of seconds, cannot hear any thing when picked up. Hi Scott, I uncheck that already, IPIPGW config : Current configuration : 4926 bytes ! ! Last configuration change at 19:00:36 AUS Fri Mar 1 2002 ! NVRAM config last updated at 18:42:19 AUS Fri Mar 1 2002 ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname C2600 ! boot-start-marker boot-end-marker ! ! no aaa new-model memory-size iomem 10 clock timezone AUS 10 network-clock-participate slot 1 no network-clock-participate wic 0 ip cef ! ! ! ! no ip domain lookup ! ! ! frame-relay switching isdn switch-type primary-ni voice-card 1 dsp services dspfarm ! ! ! ! voice service voip allow-connections h323 to h323 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! controller T1 1/0 framing esf clock source internal linecode b8zs pri-group timeslots 1-10,24 ! controller T1 1/1 framing esf clock source internal linecode b8zs pri-group timeslots 1-10,24 ! controller E1 1/2 ds0-group 0 timeslots 1-2 type r2-digital r2-semi-compelled ani ! controller E1 1/3 ! ip tftp source-interface Loopback10 ! ! ! ! ! interface Loopback0 ip address 7.7.7.7 255.255.255.255 ! interface Loopback2 ip address 2.2.2.2 255.255.255.0 ip route-cache same-interface h323-gateway voip interface h323-gateway voip id IPIPGWZONE ipaddr 7.7.7.7 1719 h323-gateway voip h323-id IPIPGW ! interface Loopback10 no ip address ! interface FastEthernet0/0 no ip address duplex auto speed auto ! interface FastEthernet0/0.200 encapsulation dot1Q 200 ip address 200.0.0.254 255.255.255.0 ! interface Serial0/0 no ip address shutdown clock rate 115200 ! interface Service-Engine0/0 no ip address shutdown ! interface Serial0/1 no ip address encapsulation frame-relay clock rate 115200 frame-relay intf-type dce frame-relay route 109 interface Serial0/3 901 ! interface Serial0/2 no ip address encapsulation frame-relay clock rate 115200 frame-relay intf-type dce frame-relay route 209 interface Serial0/3 902 ! interface Serial0/3 no ip address encapsulation frame-relay clock rate 115200 frame-relay intf-type dce frame-relay route 901 interface Serial0/1 109 frame-relay route 902 interface Serial0/2 209 ! interface Serial1/0:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn protocol-emulate network isdn incoming-voice voice no cdp enable ! interface Serial1/1:23 no ip address encapsulation hdlc isdn switch-type primary-ni isdn protocol-emulate network isdn incoming-voice voice no cdp enable ! router ospf 1 log-adjacency-changes network 0.0.0.0 255.255.255.255 area 0 ! no ip forward-protocol nd ip route 10.0.0.0 255.255.255.0 FastEthernet0/0 ! ! no ip http server no ip http secure-server ! ! ! tftp-server flash:2500.bin ! control-plane ! ! ! voice-port 1/0:23 ! voice-port 1/1:23 ! voice-port 1/2:0 ! ! mgcp ! sccp local FastEthernet0/0.200 sccp ccm 200.0.0.254 identifier 1 sccp ! sccp ccm group 1 associate ccm 1 priority 1 associate profile 1 register XCODER ! dspfarm profile 1 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 4 associate application SCCP ! ! dial-peer voice 5000 pots destination-pattern 098215... direct-inward-dial forward-digits 8 ! dial-peer voice 4000 pots destination-pattern 06134... direct-inward-dial forward-digits 4 ! dial-peer voice 30 pots destination-pattern 01144334... - Show quoted text - port 1/2:0 forward-digits 8 ! dial-peer voice 200 pots incoming called-number . direct-inward-dial port 1/2:0 ! dial-peer voice 600 voip destination-pattern session target ras dtmf-relay h245-alphanumeric codec g711ulaw ! dial-peer voice 601 voip destination-pattern 3... session target ras dtmf-relay h245-alphanumeric codec g711ulaw ! gateway timer receive-rtp 1200 ! ! ! ! gatekeeper zone local CCMZONE abc.com 7.7.7.7 zone local HQZONE abc.com zone local IPIPGWCCMZONE abc.com zone local IPIPGWZONE abc.com zone local FXSZONE abc.com invia IPIPGWZONE outvia IPIPGWZONE enable-intrazone no zone subnet CCMZONE default enable zone
[OSL | CCIE_Voice] what is this suppose to mean? different Codecs show up as G711 and G729 on the call parties for a call,
Hi, suppose following scenario: IPPHONE1 CCM--HQGK/PSTN-BR2 (CME)IPPHONE 2 I force CCM to use G729, by creating region using G729. call coming from ip phone1 to GK via trunk from CCM and GK routes it to HQ. HQ transfer it to PSTN and then call goes to BR2 and IPphone 2. On IPPHONE1 -G729 on HQ ---using show call active voiceG729 on PSTN router --G711 on IPPHONE2 G711 Why I see two different codec on PSTN router and IP phone1? How come codec changes from G729 to G711? How can I prevent it and see G729 on IPphone2 as well? Jeremy
[OSL | CCIE_Voice] [HELP]: PSTN Gateway Backbone GK configuration
Hello Experts, I am setting up my LAB planning to run PSTN GW Backbone (PSTN) – GK on the same router (2821) Can someone help me out with the configuration or sample. Regards, Shadab
Re: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration
Thanks Marwa, I got the same at the below mentioned location. Seeing the configuration, I found that translation-profile is applied under voice-ports, however NO translation-profile is created; just seeing translation-rules??? Any advice! -Shadab From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of marwa Sent: Wednesday, October 22, 2008 3:51 PM To: Shadab Abbasi (moabbasi); ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration Hello, You can find the initial configurations for all the devices in the Proctor Labs support forum: http://proctorlabs.com/forum/ To access the forum, simply create a Proctor Labs account, which is free of charge, and use those credentials to enter the support forum. You'll find the configs you're looking for in the Voice FAQ section. Marwa - Original Message - From: Shadab Abbasi (moabbasi) mailto:[EMAIL PROTECTED] To: ccie_voice@onlinestudylist.com Sent: Wednesday, October 22, 2008 10:54 AM Subject: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration Hello Experts, I am setting up my LAB planning to run PSTN GW Backbone (PSTN) - GK on the same router (2821) Can someone help me out with the configuration or sample? Regards, Shadab
Re: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration
hello, here is the conf in the attachment Eng./ Marwa Ahmed , M.Sc. Systems Engineering of Egypt (S.E.E) CCVP Cisco IP Communications Support Specialist CCNP Senior Customer Support Engineer Tel : +2 02 22921100 Fax : +2 02 22901673 e-mail : [EMAIL PROTECTED] - Original Message - From: Shadab Abbasi (moabbasi) To: marwa ; ccie_voice@onlinestudylist.com Sent: Wednesday, October 22, 2008 12:36 PM Subject: RE: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration Thanks Marwa, I got the same at the below mentioned location. Seeing the configuration, I found that translation-profile is applied under voice-ports, however NO translation-profile is created; just seeing translation-rules??? Any advice! -Shadab From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of marwa Sent: Wednesday, October 22, 2008 3:51 PM To: Shadab Abbasi (moabbasi); ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration Hello, You can find the initial configurations for all the devices in the Proctor Labs support forum: http://proctorlabs.com/forum/ To access the forum, simply create a Proctor Labs account, which is free of charge, and use those credentials to enter the support forum. You'll find the configs you're looking for in the Voice FAQ section. Marwa - Original Message - From: Shadab Abbasi (moabbasi) To: ccie_voice@onlinestudylist.com Sent: Wednesday, October 22, 2008 10:54 AM Subject: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration Hello Experts, I am setting up my LAB planning to run PSTN GW Backbone (PSTN) - GK on the same router (2821) Can someone help me out with the configuration or sample? Regards, Shadab All - a few have asked what our default configs look like - they are the same for every lab and have a base level of IP connectivity. This does NOT mean that every L3 interface is necessarily created for you - some are your responsibility to create. This goes also for L2 VLANs - they may be created - but not applied or trunked to the router for L3 routing - again the candidate's responsibility. ALSO PLEASE NOTE: This configuration is based on the IP Addressing Scheme akin to all IPexpert Voice products. Also note that these base configs are specific to Pod 25 (so as to correlate with this posting here: http://proctorlabs.com/forum/showflat.php?Cat=Board=VFAQNumber=23583page=0view=collapsedsb=5o=fpart=1 )- so if you are using this for your own lab please be aware that the 2nd octet of your IP address will change depending on the Pod number you choose as your home pod. --- ** BEGIN HQ Router *** --- ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname P25-HQ-RTR ! boot-start-marker boot system flash:c2800nm-adventerprisek9_ivs-mz.124-3g.bin boot-end-marker ! logging buffered 51200 warnings ! no aaa new-model ! resource policy ! network-clock-participate wic 0 network-clock-select 1 T1 0/0/0 ip subnet-zero ! ! ip cef ! ! no ip domain lookup ! ! voice-card 0 no dspfarm ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! controller T1 0/0/0 description ** Connected to PSTN-WAN Controller T1 0/1/0 for T1 Data ** framing esf linecode b8zs channel-group 0 timeslots 1-24 ! ! ! ! ! interface Loopback0 ip address 172.25.100.1 255.255.255.0 ip ospf network point-to-point ! interface FastEthernet0/0 no ip address shutdown duplex auto speed auto ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0:0 no ip address encapsulation frame-relay IETF frame-relay lmi-type ansi ! interface Serial0/0/0:0.1 point-to-point description ** Frame Relay PVC to BR1 Site ** ip address 162.25.101.1 255.255.255.0 ip ospf mtu-ignore frame-relay interface-dlci 201 ! interface Serial0/0/0:0.2 point-to-point description ** Frame Relay PVC to BR2 Site ** ip address 162.25.102.1 255.255.255.0 ip ospf mtu-ignore frame-relay interface-dlci 202 ! router ospf 1 log-adjacency-changes network 10.25.100.0 0.0.0.255 area 0 network 10.25.200.0 0.0.0.255 area 0 network 162.25.101.0 0.0.0.255 area 0 network 162.25.102.0 0.0.0.255 area 0 network 172.25.100.0 0.0.0.255 area 0 ! ip classless ! ! ip http server ip http authentication local no ip http secure-server ! ! ! ! ! control-plane ! ! ! ! ! ! ! ! ! ! gatekeeper shutdown ! ! line con 0 exec-timeout 0 0 logging synchronous line aux 0 line vty 0 4 privilege level 15 no login transport input telnet line vty 5 15 privilege level 15 no login transport input telnet ! scheduler allocate
Re: [OSL | CCIE_Voice] Fwd: AC User Broadcast Hunting
You are correct. This feature only works with user/line. Cheers! From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Jacob Owen Sent: Tuesday, October 21, 2008 7:11 PM To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Fwd: AC User Broadcast Hunting All, I think the issue: This works only when the members of the hunt group are user/line. This does not work when the hunt group uses directory numbers as members. I had them set as directory numbers. Good info to know Mark Cardwell | Systems Engineer | MidAtlantic | Presidio Networked Solutions 7601 Ora Glen Drive, Suite 100, Greenbelt, MD 20770 | mailto:[EMAIL PROTECTED] D: 571.225.0132 | http://www.presidio.com/ -- Forwarded message -- From: Jacob Owen [EMAIL PROTECTED] Date: Tue, Oct 21, 2008 at 7:06 PM Subject: AC User Broadcast Hunting To: ccie_voice@onlinestudylist.com I have Attendant Console setup and working well for Circular and First Available hunting but for some reason when I change it to Broadcast Hunting and reset the ICD service and AC CTI Route Point and make a call all I get is Music on hold when being placed in the queue. I have my AC Application up and running but no broadcast calls are being shown, is their something special I am supposed to do to get this to function? Thanks for any help. -- Jacob Owen CCIE #14063 (RS, Service Provider), CCDP, CCVP -- Jacob Owen CCIE #14063 (RS, Service Provider), CCDP, CCVP
Re: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration
I am using the below config, it is working for me, try it: - isdn switch-type primary-ni ! voice-card 0 no dspfarm ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! controller E1 0/2/0 pri-group timeslots 1-3,16 ! controller T1 0/3/0 framing esf linecode b8zs pri-group timeslots 1-3,24 ! controller T1 0/3/1 framing esf linecode b8zs pri-group timeslots 1-3,24 ! ! ! ! ! ! interface Serial0/2/0:15 no ip address isdn switch-type primary-ni isdn protocol-emulate network isdn incoming-voice voice no cdp enable ! interface Serial0/3/0:23 no ip address isdn switch-type primary-ni isdn protocol-emulate network isdn incoming-voice voice no cdp enable ! interface Serial0/3/1:23 no ip address isdn switch-type primary-ni isdn protocol-emulate network isdn incoming-voice voice no cdp enable ! ! voice-port 0/2/0:15 ! voice-port 0/3/0:23 ! voice-port 0/3/1:23 ! ! ! ! ! dial-peer voice 10 pots destination-pattern 915535 incoming called-number . port 0/3/0:23 ! dial-peer voice 11 pots destination-pattern 902773 port 0/3/1:23 ! dial-peer voice 12 pots destination-pattern 01176 incoming called-number . port 0/2/0:15 ! ! ! ! telephony-service load 7960-7940 P00403020214 max-ephones 4 max-dn 12 ip source-address 192.168.41.1 port 2000 create cnf-files version-stamp 7960 Feb 19 2007 15:52:07 max-conferences 8 gain -6 ! ! ephone-dn 1 number 911 ! ! ephone-dn 2 number 0119876543210 ! ! ephone-dn 3 number 902463 ! ! ephone-dn 4 number 916435 ! ! ephone-dn 5 number 212555 ! ! ephone 1 mac-address button 1:1 2:2 3:3 4:4 5:5 For the conection beteen PSTN router and your gw you need to create a crossover cable to connect the E1 / T1 make the connection as follows: 14 25 41 52 Regards, Bala. --- On Wed, 22/10/08, Shadab Abbasi (moabbasi) [EMAIL PROTECTED] wrote: From: Shadab Abbasi (moabbasi) [EMAIL PROTECTED] Subject: Re: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration To: marwa [EMAIL PROTECTED], ccie_voice@onlinestudylist.com Date: Wednesday, 22 October, 2008, 4:06 PM Thanks Marwa, I got the same at the below mentioned location. Seeing the configuration, I found that translation-profile is applied under voice-ports, however NO translation-profile is created; just seeing translation-rules??? Any advice! -Shadab From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of marwa Sent: Wednesday, October 22, 2008 3:51 PM To: Shadab Abbasi (moabbasi); ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration Hello, You can find the initial configurations for all the devices in the Proctor Labs support forum: http://proctorlabs.com/forum/ To access the forum, simply create a Proctor Labs account, which is free of charge, and use those credentials to enter the support forum. You'll find the configs you're looking for in the Voice FAQ section. Marwa - Original Message - From: Shadab Abbasi (moabbasi) To: ccie_voice@onlinestudylist.com Sent: Wednesday, October 22, 2008 10:54 AM Subject: [OSL | CCIE_Voice] FW: PSTN Gateway Backbone GK configuration Hello Experts, I am setting up my LAB planning to run PSTN GW Backbone (PSTN) – GK on the same router (2821) Can someone help me out with the configuration or sample? Regards, Shadab Get your preferred Email name! Now you can @ymail.com and @rocketmail.com. http://mail.promotions.yahoo.com/newdomains/aa/
Re: [OSL | CCIE_Voice] Same Config CM Phone drops to CUE
telephony-servicecall-forward pattern .T That fixed it. Thanks! On Tue, Oct 21, 2008 at 1:30 AM, Yung Hung [EMAIL PROTECTED] wrote: Also make sure you're allowing connections: Voice service voip Allow h323 to sip** *From:* [EMAIL PROTECTED] [mailto: [EMAIL PROTECTED] *On Behalf Of *Ricardo Arevalo *Sent:* Monday, October 20, 2008 10:08 PM *To:* Ryan Trauernicht *Cc:* ccie_voice@onlinestudylist.com *Subject:* Re: [OSL | CCIE_Voice] Same Config CM Phone drops to CUE Ryan, In telephony-service add the commando: call-forward pattern .T //r.a. On Mon, Oct 20, 2008 at 11:25 PM, Ryan Trauernicht [EMAIL PROTECTED] wrote: CMGKCME Phone then to CUE on no answer. Call just drops when trying to goto CUe. I know CUE supports G711 only, so I have a transcoder on the CME router and shows registered show sdspfarm units. Any reason on CUE that would happen from the following version: Installed Packages: - Installer 2.2.1 - Thirdparty 2.3.2 - Bootloader (Primary) 2.1.2 - Infrastructure 2.3.4 - Global 2.3.4 - GPL Infrastructure 2.3.0 - Voice Mail 2.3.2 - Bootloader (Secondary) 2.1.2 - Core 2.3.4 - Auto Attendant 2.3.0 Sorry for the flood of emails the past few minutes.
Re: [OSL | CCIE_Voice] what is this suppose to mean? different Codecs show up as G711 and G729 on the call parties for a call,
my PSTN is 2600 router with 2xT1 and 2xE1, link between Br2 and pstn is E1---R2 signaling and between HQ and pstn is T1,PRI Br2 not registered to GK, just HQ and CCM registered to GK Tanx Jeremy On Thu, Oct 23, 2008 at 2:32 AM, Ricardo Arevalo [EMAIL PROTECTED] wrote: Jeremy, the call in this segment: ...GK/PSTN-BR2 (CME)... Is actually a PSTN call? i mean are you using any ISDN or R2 line? Or Is it an Gatekeeper handled call? (BR2 registered to GK) //r.a. On Wed, Oct 22, 2008 at 4:20 AM, jeremy co [EMAIL PROTECTED]wrote: Hi, suppose following scenario: IPPHONE1 CCM--HQGK/PSTN-BR2 (CME)IPPHONE 2 I force CCM to use G729, by creating region using G729. call coming from ip phone1 to GK via trunk from CCM and GK routes it to HQ. HQ transfer it to PSTN and then call goes to BR2 and IPphone 2. On IPPHONE1 -G729 on HQ ---using show call active voiceG729 on PSTN router --G711 on IPPHONE2 G711 Why I see two different codec on PSTN router and IP phone1? How come codec changes from G729 to G711? How can I prevent it and see G729 on IPphone2 as well? Jeremy
Re: [OSL | CCIE_Voice] what is this suppose to mean? different Codecs show up as G711 and G729 on the call parties for a call,
Ok, so in this case, the call from HQ to GK is a G729 call as defined by your region. Then the call is routed to PSTN by the GK. The BR2 receive tha call as G711 as default a codec and send it to any internal phone. All the call coming from PSTN are handled by default as G711 calls. //r.a. On Wed, Oct 22, 2008 at 11:39 AM, jeremy co [EMAIL PROTECTED] wrote: my PSTN is 2600 router with 2xT1 and 2xE1, link between Br2 and pstn is E1---R2 signaling and between HQ and pstn is T1,PRI Br2 not registered to GK, just HQ and CCM registered to GK Tanx Jeremy On Thu, Oct 23, 2008 at 2:32 AM, Ricardo Arevalo [EMAIL PROTECTED] wrote: Jeremy, the call in this segment: ...GK/PSTN-BR2 (CME)... Is actually a PSTN call? i mean are you using any ISDN or R2 line? Or Is it an Gatekeeper handled call? (BR2 registered to GK) //r.a. On Wed, Oct 22, 2008 at 4:20 AM, jeremy co [EMAIL PROTECTED]wrote: Hi, suppose following scenario: IPPHONE1 CCM--HQGK/PSTN-BR2 (CME)IPPHONE 2 I force CCM to use G729, by creating region using G729. call coming from ip phone1 to GK via trunk from CCM and GK routes it to HQ. HQ transfer it to PSTN and then call goes to BR2 and IPphone 2. On IPPHONE1 -G729 on HQ ---using show call active voiceG729 on PSTN router --G711 on IPPHONE2 G711 Why I see two different codec on PSTN router and IP phone1? How come codec changes from G729 to G711? How can I prevent it and see G729 on IPphone2 as well? Jeremy
Re: [OSL | CCIE_Voice] what is this suppose to mean? different Codecs show up as G711 and G729 on the call parties for a call,
Jeremy, the call in this segment: ...GK/PSTN-BR2 (CME)... Is actually a PSTN call? i mean are you using any ISDN or R2 line? Or Is it an Gatekeeper handled call? (BR2 registered to GK) //r.a. On Wed, Oct 22, 2008 at 4:20 AM, jeremy co [EMAIL PROTECTED] wrote: Hi, suppose following scenario: IPPHONE1 CCM--HQGK/PSTN-BR2 (CME)IPPHONE 2 I force CCM to use G729, by creating region using G729. call coming from ip phone1 to GK via trunk from CCM and GK routes it to HQ. HQ transfer it to PSTN and then call goes to BR2 and IPphone 2. On IPPHONE1 -G729 on HQ ---using show call active voiceG729 on PSTN router --G711 on IPPHONE2 G711 Why I see two different codec on PSTN router and IP phone1? How come codec changes from G729 to G711? How can I prevent it and see G729 on IPphone2 as well? Jeremy
[OSL | CCIE_Voice] Problem with PVDM-2 Conference registration
Hi All, I have an ongoing problem with creating a media resources on CME router. I create 2 dspfarm profiles, configure SCCP, register with CME... Transcoding registeres fine, but Conferencing does not. Here is part of the config, and the SCCP status: voice-card 0 dspfarm dsp services dspfarm ! sccp local GigabitEthernet0/0.123 sccp ccm 10.10.66.254 identifier 1 sccp ip precedence 3 sccp ! sccp ccm group 1 bind interface GigabitEthernet0/0.123 associate ccm 1 priority 1 associate profile 1 register cfb001da10466d8 associate profile 2 register mtp001da10466d8 ! dspfarm profile 2 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 4 associate application SCCP ! dspfarm profile 1 conference codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 2 associate application SCCP ! telephony-service sdspfarm units 2 sdspfarm tag 1 cfb001da10466d8 sdspfarm tag 2 mtp001da10466d8 ip source-address 10.10.66.254 port 2000 max-conferences 2 gain -6 ! - R7-BR2#sh sccp SCCP Admin State: UP Gateway IP Address: 142.103.66.254, Port Number: 2000 IP Precedence: 3 User Masked Codec list: None Call Manager: 142.103.66.254, Port Number: 2000 Priority: N/A, Version: 3.1, Identifier: 1 Transcoding Oper State: ACTIVE - Cause Code: NONE Active Call Manager: 142.103.66.254, Port Number: 2000 TCP Link Status: CONNECTED, Profile Identifier: 2 Reported Max Streams: 8, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30 Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30 Conferencing Oper State: ACTIVE_IN_PROGRESS - Cause Code: CCM_REGISTER_FAILED Active Call Manager: 142.103.66.254, Port Number: 2000 TCP Link Status: NOT_CONNECTED, Profile Identifier: 1 Reported Max Streams: 16, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: g729br8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30 Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
Re: [OSL | CCIE_Voice] Multiple Cisco IP Communicator
If you wish to purchase I have voucher codes that give you 35% off - and you only need to purchase one license to be allowed to run many instances - if they are one machine. Only catch is the voucher code I generate has to be used within one week - so unicast me if you would like one. -- Mark Snow CCIE #14073 (Voice, Security) Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.309.413.4097 Mailto: [EMAIL PROTECTED] -- Join our free online support and peer group communities: http://www.IPexpert.com/communities -- IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On- Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. -- On Oct 20, 2008, at 11:21 AM, KIZILCABOLUK DENIZ wrote: I installed the IP-Blue from Proctorlabs but it gave me error everytime try to open its settings and closed itself. Than I installed new version from ipblue.com it worked but wants me to purchase. Deniz From: Jacob Owen [mailto:[EMAIL PROTECTED] Sent: Monday, October 20, 2008 5:04 PM To: KIZILCABOLUK DENIZ Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Multiple Cisco IP Communicator From what I Have been told it isn't possible, that's why IP Blue is the preferred way to get this to work. I use the EZVPN approach to connect to Proctorlabs and have about 2-3 PC's that I can remote desktop too and run IP Communicator from them. Works like a champ. On Mon, Oct 20, 2008 at 10:53 AM, KIZILCABOLUK DENIZ [EMAIL PROTECTED] wrote: Hi, How can I open multiple IP Communicator on my laptop? Do you have an idea? Thanks, Deniz -- Jacob Owen CCIE #14063 (RS, Service Provider), CCDP, CCVP
Re: [OSL | CCIE_Voice] Multiple Cisco IP Communicator
Yes that is correct you can not run multiple instances of IPC on your one machine unless you have virtual machines running. On Mon, Oct 20, 2008 at 10:53 AM, KIZILCABOLUK DENIZ [EMAIL PROTECTED] wrote: Hi, How can I open multiple IP Communicator on my laptop? Do you have an idea? Thanks, Deniz
Re: [OSL | CCIE_Voice] Callmanager URL's and Directory Paths
Unless you are using DNS - always a good idea to set to IP. Shouldn't matter so long as the MoHDropAudioFilesHere folder exists on the SAME machine as the the TFTP server. However - if say the MoH Audio Xlator service is running on the Pub and you were instructed (for whatever odd reason) to make the Sub the TFTP server - then you would need the IP address of the Sub there (unless you have a hosts file on the Pub with the Sub hostname and proper IP address). HTH, -- Mark Snow CCIE #14073 (Voice, Security) Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.309.413.4097 Mailto: [EMAIL PROTECTED] -- Join our free online support and peer group communities: http://www.IPexpert.com/communities -- IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On- Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. -- On Oct 21, 2008, at 1:56 PM, Kevin Porter wrote: When it comes to setting URL’s and Directory Path’s in CallManager Services, should the Default TFTP Path for the Cisco MOH Audio Translator Service be changed to an IP or is it OK to leave the Server Hostname… Thanks, Kevin Kevin Porter Systems Engineer L4 Netelligent Corporation 400 South Woods Mill Drive, Suite 105 St. Louis, MO 63017 Office: (314) 392-6921 Cell: (314) 852-1252 Fax: (314) 392-9760 [EMAIL PROTECTED] www.netelligent.com Bridging The Gap Between Good and GREAT IP Communications!
[OSL | CCIE_Voice] Antw: Problem with PVDM-2 Conference registration
Hi Michael, Hardware Conferencing is not supported with CCME 3.3. When you want to use a Hardware Conferencebridge with CCME you have to use CCME Version 4.0 or maybe higher, i don´t remember it at the moment. HTH /Robert Michael Shavrov[EMAIL PROTECTED] schrieb am Mittwoch, 22. Oktober 2008 um 18:57 in Nachricht 93f2ba42c46071d4f82376100596cbc2: Hi All, I have an ongoing problem with creating a media resources on CME router. I create 2 dspfarm profiles, configure SCCP, register with CME... Transcoding registeres fine, but Conferencing does not. Here is part of the config, and the SCCP status: voice-card 0 dspfarm dsp services dspfarm ! sccp local GigabitEthernet0/0.123 sccp ccm 10.10.66.254 identifier 1 sccp ip precedence 3 sccp ! sccp ccm group 1 bind interface GigabitEthernet0/0.123 associate ccm 1 priority 1 associate profile 1 register cfb001da10466d8 associate profile 2 register mtp001da10466d8 ! dspfarm profile 2 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 4 associate application SCCP ! dspfarm profile 1 conference codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 2 associate application SCCP ! telephony-service sdspfarm units 2 sdspfarm tag 1 cfb001da10466d8 sdspfarm tag 2 mtp001da10466d8 ip source-address 10.10.66.254 port 2000 max-conferences 2 gain -6 ! - R7-BR2#sh sccp SCCP Admin State: UP Gateway IP Address: 142.103.66.254, Port Number: 2000 IP Precedence: 3 User Masked Codec list: None Call Manager: 142.103.66.254, Port Number: 2000 Priority: N/A, Version: 3.1, Identifier: 1 Transcoding Oper State: ACTIVE - Cause Code: NONE Active Call Manager: 142.103.66.254, Port Number: 2000 TCP Link Status: CONNECTED, Profile Identifier: 2 Reported Max Streams: 8, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30 Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30 Conferencing Oper State: ACTIVE_IN_PROGRESS - Cause Code: CCM_REGISTER_FAILED Active Call Manager: 142.103.66.254, Port Number: 2000 TCP Link Status: NOT_CONNECTED, Profile Identifier: 1 Reported Max Streams: 16, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: g729br8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30 Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
Re: [OSL | CCIE_Voice] Problem with PVDM-2 Conference registration
Michael, It may seem weird but i have noticed until I set the Max-ephones X command my MTP/CONF resources won't register to CCME. It's worth a shot, i know it usually is only an issue when setting a transcoder on HQ since it inherintly doesn't have ephones registered to it and therefore that command is usually missing. Try it and see what happens On Wed, Oct 22, 2008 at 12:57 PM, Michael Shavrov [EMAIL PROTECTED]wrote: Hi All, I have an ongoing problem with creating a media resources on CME router. I create 2 dspfarm profiles, configure SCCP, register with CME... Transcoding registeres fine, but Conferencing does not. Here is part of the config, and the SCCP status: voice-card 0 dspfarm dsp services dspfarm ! sccp local GigabitEthernet0/0.123 sccp ccm 10.10.66.254 identifier 1 sccp ip precedence 3 sccp ! sccp ccm group 1 bind interface GigabitEthernet0/0.123 associate ccm 1 priority 1 associate profile 1 register cfb001da10466d8 associate profile 2 register mtp001da10466d8 ! dspfarm profile 2 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 4 associate application SCCP ! dspfarm profile 1 conference codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 2 associate application SCCP ! telephony-service sdspfarm units 2 sdspfarm tag 1 cfb001da10466d8 sdspfarm tag 2 mtp001da10466d8 ip source-address 10.10.66.254 port 2000 max-conferences 2 gain -6 ! - R7-BR2#sh sccp SCCP Admin State: UP Gateway IP Address: 142.103.66.254, Port Number: 2000 IP Precedence: 3 User Masked Codec list: None Call Manager: 142.103.66.254, Port Number: 2000 Priority: N/A, Version: 3.1, Identifier: 1 Transcoding Oper State: ACTIVE - Cause Code: NONE Active Call Manager: 142.103.66.254, Port Number: 2000 TCP Link Status: CONNECTED, Profile Identifier: 2 Reported Max Streams: 8, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30 Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30 Conferencing Oper State: ACTIVE_IN_PROGRESS - Cause Code: CCM_REGISTER_FAILED Active Call Manager: 142.103.66.254, Port Number: 2000 TCP Link Status: NOT_CONNECTED, Profile Identifier: 1 Reported Max Streams: 16, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: g729br8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30 Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30 -- Jacob Owen CCIE #14063 (RS, Service Provider), CCDP, CCVP
Re: [OSL | CCIE_Voice] Problem with PVDM-2 Conference registration
I have experienced the same situation as Jacob. In fact, when the conference bridge registers, you can see an ephone type registration. Scott Hardesty | Cisco Engineer | MidAtlantic | Presidio Networked Solutions 7601 Ora Glen Drive, Suite 100, Greenbelt, MD 20770 | mailto:[EMAIL PROTECTED] D: 301.313.2041 | C: 443.789.1219 | http://www.presidio.com/ From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Jacob Owen Sent: Wednesday, October 22, 2008 2:39 PM To: Michael Shavrov Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Problem with PVDM-2 Conference registration Michael, It may seem weird but i have noticed until I set the Max-ephones X command my MTP/CONF resources won't register to CCME. It's worth a shot, i know it usually is only an issue when setting a transcoder on HQ since it inherintly doesn't have ephones registered to it and therefore that command is usually missing. Try it and see what happens On Wed, Oct 22, 2008 at 12:57 PM, Michael Shavrov [EMAIL PROTECTED] wrote: Hi All, I have an ongoing problem with creating a media resources on CME router. I create 2 dspfarm profiles, configure SCCP, register with CME... Transcoding registeres fine, but Conferencing does not. Here is part of the config, and the SCCP status: voice-card 0 dspfarm dsp services dspfarm ! sccp local GigabitEthernet0/0.123 sccp ccm 10.10.66.254 identifier 1 sccp ip precedence 3 sccp ! sccp ccm group 1 bind interface GigabitEthernet0/0.123 associate ccm 1 priority 1 associate profile 1 register cfb001da10466d8 associate profile 2 register mtp001da10466d8 ! dspfarm profile 2 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 4 associate application SCCP ! dspfarm profile 1 conference codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 2 associate application SCCP ! telephony-service sdspfarm units 2 sdspfarm tag 1 cfb001da10466d8 sdspfarm tag 2 mtp001da10466d8 ip source-address 10.10.66.254 port 2000 max-conferences 2 gain -6 ! - R7-BR2#sh sccp SCCP Admin State: UP Gateway IP Address: 142.103.66.254, Port Number: 2000 IP Precedence: 3 User Masked Codec list: None Call Manager: 142.103.66.254, Port Number: 2000 Priority: N/A, Version: 3.1, Identifier: 1 Transcoding Oper State: ACTIVE - Cause Code: NONE Active Call Manager: 142.103.66.254, Port Number: 2000 TCP Link Status: CONNECTED, Profile Identifier: 2 Reported Max Streams: 8, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30 Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30 Conferencing Oper State: ACTIVE_IN_PROGRESS - Cause Code: CCM_REGISTER_FAILED Active Call Manager: 142.103.66.254, Port Number: 2000 TCP Link Status: NOT_CONNECTED, Profile Identifier: 1 Reported Max Streams: 16, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: g729br8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30 Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30 -- Jacob Owen CCIE #14063 (RS, Service Provider), CCDP, CCVP
Re: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration
Looks like you right - I've tried it with both, PVDM and PVDM2. In both cases transcoder registers instantly, but conferencing does not. I will try to upgrade IOS on one of the router to CME 4.0 and see if it will solve the problem with the same config. - Original Message - From: Robert Schuknecht [EMAIL PROTECTED] To: ccie_voice@onlinestudylist.com; [EMAIL PROTECTED] Sent: Wednesday, October 22, 2008 2:26 PM Subject: Antw: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration Hi Michael, Hardware Conferencing is not supported with CCME 3.3. When you want to use a Hardware Conferencebridge with CCME you have to use CCME Version 4.0 or maybe higher, i don´t remember it at the moment. HTH /Robert Michael Shavrov[EMAIL PROTECTED] schrieb am Mittwoch, 22. Oktober 2008 um 18:57 in Nachricht 93f2ba42c46071d4f82376100596cbc2: Hi All, I have an ongoing problem with creating a media resources on CME router. I create 2 dspfarm profiles, configure SCCP, register with CME... Transcoding registeres fine, but Conferencing does not. Here is part of the config, and the SCCP status: voice-card 0 dspfarm dsp services dspfarm ! sccp local GigabitEthernet0/0.123 sccp ccm 10.10.66.254 identifier 1 sccp ip precedence 3 sccp ! sccp ccm group 1 bind interface GigabitEthernet0/0.123 associate ccm 1 priority 1 associate profile 1 register cfb001da10466d8 associate profile 2 register mtp001da10466d8 ! dspfarm profile 2 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 4 associate application SCCP ! dspfarm profile 1 conference codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 2 associate application SCCP ! telephony-service sdspfarm units 2 sdspfarm tag 1 cfb001da10466d8 sdspfarm tag 2 mtp001da10466d8 ip source-address 10.10.66.254 port 2000 max-conferences 2 gain -6 ! - R7-BR2#sh sccp SCCP Admin State: UP Gateway IP Address: 142.103.66.254, Port Number: 2000 IP Precedence: 3 User Masked Codec list: None Call Manager: 142.103.66.254, Port Number: 2000 Priority: N/A, Version: 3.1, Identifier: 1 Transcoding Oper State: ACTIVE - Cause Code: NONE Active Call Manager: 142.103.66.254, Port Number: 2000 TCP Link Status: CONNECTED, Profile Identifier: 2 Reported Max Streams: 8, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30 Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30 Conferencing Oper State: ACTIVE_IN_PROGRESS - Cause Code: CCM_REGISTER_FAILED Active Call Manager: 142.103.66.254, Port Number: 2000 TCP Link Status: NOT_CONNECTED, Profile Identifier: 1 Reported Max Streams: 16, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: g729br8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30 Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
[OSL | CCIE_Voice] Configuring Voice-Card for DSPFarm
Quick question...when configuring the Voice-Card to act as a dspfarm, I have seen almost all the IPExpert config's to look like this.. Voice-card 0 dspfarm dsp services dspfarm but, in the real world, I can not do this with a shared PVDM that is terminating voice circuits (PRI, FXS, FXO, etc...). I have had to use the following config: Voice-card 0 no dspfarm dsp services dspfarm So, the question is this, is there anything wrong with my config that would cause issues? Thanks, Kevin Kevin Porter Systems Engineer L4 Netelligent Corporation 400 South Woods Mill Drive, Suite 105 St. Louis, MO 63017 Office: (314) 392-6921 Cell: (314) 852-1252 Fax: (314) 392-9760 [EMAIL PROTECTED] www.netelligent.com Bridging The Gap Between Good and GREAT IP Communications!
Re: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration
Michael, I am running CME version 3.3 and I can register a hardware conference Transcoder. I would make sure you have enough ephones. SEE BELOW, EPHONE-3 has registed using the gi0/0 interface BR2#sho ephone registered ephone-1 Mac:0011.BB53.7636 TCP socket:[6] activeLine:0 REGISTERED in SCCP ver 6 mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 IP:142.107.66.11 50031 Telecaster 7940 keepalive 54 max_line 2 button 1: dn 1 number 4001 CH1 IDLE CH2 IDLE Username: phnOne Password: null ephone-2 Mac:0014.A963.9EDF TCP socket:[5] activeLine:0 REGISTERED in SCCP ver 6 mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 IP:142.107.66.12 50035 Telecaster 7940 keepalive 54 max_line 2 button 1: dn 2 number 4002 CH1 IDLE CH2 IDLE Username: phoneTwo Password: null ephone-3 Mac:0011.9348.0940 TCP socket:[2] activeLine:0 REGISTERED in SCCP ver 0 + Authentication mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 IP:142.107.66.254 39825 Unknown 51 keepalive 6 max_line 0 SEE that the SCCP Conference bridge is ACTIVE BR2#sho Oct 22 20:23:10.488: %SYS-5-CONFIG_I: Configured from console by consolesccp SCCP Admin State: UP Gateway IP Address: 142.107.66.254, Port Number: 2000 IP Precedence: 5 User Masked Codec list: None Call Manager: 142.107.71.254, Port Number: 2000 Priority: N/A, Version: 3.1, Identifier: 1 Conferencing Oper State: ACTIVE - Cause Code: NONE Active Call Manager: 142.107.71.254, Port Number: 2000 TCP Link Status: CONNECTED, Profile Identifier: 1 Reported Max Streams: 16, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: g729br8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 BR2#sho ver Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(3j), R ELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Fri 14-Dec-07 03:18 by stshen ROM: System Bootstrap, Version 12.3(11r)T1, RELEASE SOFTWARE (fc1) BR2 uptime is 1 day, 16 hours, 39 minutes System returned to ROM by reload at 15:23:51 CEST Mon Oct 20 2008 System restarted at 04:44:21 CEST Tue Oct 21 2008 System image file is flash:c3845-advipservicesk9-mz.124-3j.bin Scott Hardesty | Cisco Engineer | MidAtlantic | Presidio Networked Solutions 7601 Ora Glen Drive, Suite 100, Greenbelt, MD 20770 | mailto:[EMAIL PROTECTED] D: 301.313.2041 | C: 443.789.1219 | http://www.presidio.com/ -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Michael Shavrov Sent: Wednesday, October 22, 2008 3:01 PM To: Robert Schuknecht; ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration Looks like you right - I've tried it with both, PVDM and PVDM2. In both cases transcoder registers instantly, but conferencing does not. I will try to upgrade IOS on one of the router to CME 4.0 and see if it will solve the problem with the same config. - Original Message - From: Robert Schuknecht [EMAIL PROTECTED] To: ccie_voice@onlinestudylist.com; [EMAIL PROTECTED] Sent: Wednesday, October 22, 2008 2:26 PM Subject: Antw: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration Hi Michael, Hardware Conferencing is not supported with CCME 3.3. When you want to use a Hardware Conferencebridge with CCME you have to use CCME Version 4.0 or maybe higher, i don´t remember it at the moment. HTH /Robert Michael Shavrov[EMAIL PROTECTED] schrieb am Mittwoch, 22. Oktober 2008 um 18:57 in Nachricht 93f2ba42c46071d4f82376100596cbc2: Hi All, I have an ongoing problem with creating a media resources on CME router. I create 2 dspfarm profiles, configure SCCP, register with CME... Transcoding registeres fine, but Conferencing does not. Here is part of the config, and the SCCP status: voice-card 0 dspfarm dsp services dspfarm ! sccp local GigabitEthernet0/0.123 sccp ccm 10.10.66.254 identifier 1 sccp ip precedence 3 sccp ! sccp ccm group 1 bind interface GigabitEthernet0/0.123 associate ccm 1 priority 1 associate profile 1 register cfb001da10466d8 associate profile 2 register mtp001da10466d8 ! dspfarm profile 2 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 maximum sessions 4 associate application SCCP ! dspfarm profile 1 conference codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 2 associate application SCCP ! telephony-service sdspfarm units 2 sdspfarm tag 1
Re: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration
Scott, Do you register the conferencing DSP to the CME on the same router? How your configure your CME? I see thet your gateway IP address on SCCP is 142.107.66.254, but the DSP registers to the CallManager, which is 142.107.71.254. Are they on the same box? Do you register CME IP source with Loopback interface? Sincerely, Mike - Original Message - From: Hardesty, Scott [EMAIL PROTECTED] To: Michael Shavrov [EMAIL PROTECTED]; Robert Schuknecht [EMAIL PROTECTED]; ccie_voice@onlinestudylist.com Sent: Wednesday, October 22, 2008 3:28 PM Subject: RE: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration Michael, I am running CME version 3.3 and I can register a hardware conference Transcoder. I would make sure you have enough ephones. SEE BELOW, EPHONE-3 has registed using the gi0/0 interface BR2#sho ephone registered ephone-1 Mac:0011.BB53.7636 TCP socket:[6] activeLine:0 REGISTERED in SCCP ver 6 mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 IP:142.107.66.11 50031 Telecaster 7940 keepalive 54 max_line 2 button 1: dn 1 number 4001 CH1 IDLE CH2 IDLE Username: phnOne Password: null ephone-2 Mac:0014.A963.9EDF TCP socket:[5] activeLine:0 REGISTERED in SCCP ver 6 mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 IP:142.107.66.12 50035 Telecaster 7940 keepalive 54 max_line 2 button 1: dn 2 number 4002 CH1 IDLE CH2 IDLE Username: phoneTwo Password: null ephone-3 Mac:0011.9348.0940 TCP socket:[2] activeLine:0 REGISTERED in SCCP ver 0 + Authentication mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 IP:142.107.66.254 39825 Unknown 51 keepalive 6 max_line 0 SEE that the SCCP Conference bridge is ACTIVE BR2#sho Oct 22 20:23:10.488: %SYS-5-CONFIG_I: Configured from console by consolesccp SCCP Admin State: UP Gateway IP Address: 142.107.66.254, Port Number: 2000 IP Precedence: 5 User Masked Codec list: None Call Manager: 142.107.71.254, Port Number: 2000 Priority: N/A, Version: 3.1, Identifier: 1 Conferencing Oper State: ACTIVE - Cause Code: NONE Active Call Manager: 142.107.71.254, Port Number: 2000 TCP Link Status: CONNECTED, Profile Identifier: 1 Reported Max Streams: 16, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: g729br8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 BR2#sho ver Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(3j), R ELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Fri 14-Dec-07 03:18 by stshen ROM: System Bootstrap, Version 12.3(11r)T1, RELEASE SOFTWARE (fc1) BR2 uptime is 1 day, 16 hours, 39 minutes System returned to ROM by reload at 15:23:51 CEST Mon Oct 20 2008 System restarted at 04:44:21 CEST Tue Oct 21 2008 System image file is flash:c3845-advipservicesk9-mz.124-3j.bin Scott Hardesty | Cisco Engineer | MidAtlantic | Presidio Networked Solutions 7601 Ora Glen Drive, Suite 100, Greenbelt, MD 20770 | mailto:[EMAIL PROTECTED] D: 301.313.2041 | C: 443.789.1219 | http://www.presidio.com/ -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Michael Shavrov Sent: Wednesday, October 22, 2008 3:01 PM To: Robert Schuknecht; ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration Looks like you right - I've tried it with both, PVDM and PVDM2. In both cases transcoder registers instantly, but conferencing does not. I will try to upgrade IOS on one of the router to CME 4.0 and see if it will solve the problem with the same config. - Original Message - From: Robert Schuknecht [EMAIL PROTECTED] To: ccie_voice@onlinestudylist.com; [EMAIL PROTECTED] Sent: Wednesday, October 22, 2008 2:26 PM Subject: Antw: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration Hi Michael, Hardware Conferencing is not supported with CCME 3.3. When you want to use a Hardware Conferencebridge with CCME you have to use CCME Version 4.0 or maybe higher, i don´t remember it at the moment. HTH /Robert Michael Shavrov[EMAIL PROTECTED] schrieb am Mittwoch, 22. Oktober 2008 um 18:57 in Nachricht 93f2ba42c46071d4f82376100596cbc2: Hi All, I have an ongoing problem with creating a media resources on CME router. I create 2 dspfarm profiles, configure SCCP, register with CME... Transcoding registeres fine, but Conferencing does not. Here is part of the config, and the SCCP status: voice-card 0 dspfarm dsp services dspfarm ! sccp local GigabitEthernet0/0.123 sccp ccm 10.10.66.254 identifier 1
[OSL | CCIE_Voice] CME-CUE Transcoder Issue
If I place a call that is G729 to CME that is set to call-forward all to a CUE mailbox, I can only hear the greeting and leave a message, no problem. If an Ephone-dn or ephone-hunt forwards to CUE with either call-forward noan, call-forward busy or forwards to another DN that is call-forward all, the call stays connected, I see the Transcoder connect, but I can not hear the greeting and can not leave a message. Anybody seen this behavior before? Thanks, Kevin Kevin Porter Systems Engineer L4 Netelligent Corporation 400 South Woods Mill Drive, Suite 105 St. Louis, MO 63017 Office: (314) 392-6921 Cell: (314) 852-1252 Fax: (314) 392-9760 [EMAIL PROTECTED] www.netelligent.com Bridging The Gap Between Good and GREAT IP Communications!
Re: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration
Conf bridge shows active in terms of registered to CUCME - but can you start a conf call between three phones and show that the dsps are actually 'in-use'? I understand that you have registered it - however I don't think it will show that the hardware dsps actually in use. The only way to do this in CUCME 3.3 was to have 2 T1's loop back-to- back to each other with a crossover cable, configure a bunch of individual trunk connections (one for each channel), and then join the multicast IP address sort-of 'listening in' on each trunk connection. Config is basically the same as is used in LMR deployments. Anyway - try the con-call and send us the results if you would! Cheers, -- Mark Snow CCIE #14073 (Voice, Security) Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.309.413.4097 Mailto: [EMAIL PROTECTED] -- Join our free online support and peer group communities: http://www.IPexpert.com/communities -- IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On- Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. -- On Oct 22, 2008, at 3:28 PM, Hardesty, Scott wrote: Michael, I am running CME version 3.3 and I can register a hardware conference Transcoder. I would make sure you have enough ephones. SEE BELOW, EPHONE-3 has registed using the gi0/0 interface BR2#sho ephone registered ephone-1 Mac:0011.BB53.7636 TCP socket:[6] activeLine:0 REGISTERED in SCCP ver 6 mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 IP:142.107.66.11 50031 Telecaster 7940 keepalive 54 max_line 2 button 1: dn 1 number 4001 CH1 IDLE CH2 IDLE Username: phnOne Password: null ephone-2 Mac:0014.A963.9EDF TCP socket:[5] activeLine:0 REGISTERED in SCCP ver 6 mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 IP:142.107.66.12 50035 Telecaster 7940 keepalive 54 max_line 2 button 1: dn 2 number 4002 CH1 IDLE CH2 IDLE Username: phoneTwo Password: null ephone-3 Mac:0011.9348.0940 TCP socket:[2] activeLine:0 REGISTERED in SCCP ver 0 + Authentication mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 IP:142.107.66.254 39825 Unknown 51 keepalive 6 max_line 0 SEE that the SCCP Conference bridge is ACTIVE BR2#sho Oct 22 20:23:10.488: %SYS-5-CONFIG_I: Configured from console by consolesccp SCCP Admin State: UP Gateway IP Address: 142.107.66.254, Port Number: 2000 IP Precedence: 5 User Masked Codec list: None Call Manager: 142.107.71.254, Port Number: 2000 Priority: N/A, Version: 3.1, Identifier: 1 Conferencing Oper State: ACTIVE - Cause Code: NONE Active Call Manager: 142.107.71.254, Port Number: 2000 TCP Link Status: CONNECTED, Profile Identifier: 1 Reported Max Streams: 16, Reported Max OOS Streams: 0 Supported Codec: g711ulaw, Maximum Packetization Period: 30 Supported Codec: g711alaw, Maximum Packetization Period: 30 Supported Codec: g729ar8, Maximum Packetization Period: 60 Supported Codec: g729abr8, Maximum Packetization Period: 60 Supported Codec: g729r8, Maximum Packetization Period: 60 Supported Codec: g729br8, Maximum Packetization Period: 60 Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30 BR2#sho ver Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(3j), R ELEASE SOFTWARE (fc1) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2007 by Cisco Systems, Inc. Compiled Fri 14-Dec-07 03:18 by stshen ROM: System Bootstrap, Version 12.3(11r)T1, RELEASE SOFTWARE (fc1) BR2 uptime is 1 day, 16 hours, 39 minutes System returned to ROM by reload at 15:23:51 CEST Mon Oct 20 2008 System restarted at 04:44:21 CEST Tue Oct 21 2008 System image file is flash:c3845-advipservicesk9-mz.124-3j.bin Scott Hardesty | Cisco Engineer | MidAtlantic | Presidio Networked Solutions 7601 Ora Glen Drive, Suite 100, Greenbelt, MD 20770 | mailto:[EMAIL PROTECTED] D: 301.313.2041 | C: 443.789.1219 | http://www.presidio.com/ -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] ] On Behalf Of Michael Shavrov Sent: Wednesday, October 22, 2008 3:01 PM To: Robert Schuknecht; ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration Looks like you right - I've tried it with both, PVDM and PVDM2. In both cases transcoder registers instantly, but conferencing does not. I will try to upgrade IOS on one of the router to CME 4.0 and see if it will solve the problem with the same config. - Original Message - From: Robert Schuknecht [EMAIL PROTECTED] To: ccie_voice@onlinestudylist.com; [EMAIL PROTECTED] Sent: Wednesday, October 22, 2008 2:26 PM Subject: Antw: [OSL | CCIE_Voice] Problem with PVDM-2 Conferenceregistration Hi Michael, Hardware Conferencing is not supported with CCME
[OSL | CCIE_Voice] problem with calls comming in via h323 to CME, can't reach CUE(busy)
Doing this scenario: CCM -- h323trunk -- GK -- CME -- ephone OK PSTN -- CME -- CUE OK CCM -- h323trunk -- GK -- CME -- CUE fails Regardless of selected codec. Any suggestions? Config from CME router: Current configuration : 6164 bytes ! ! Last configuration change at 04:09:53 UTC Sat Oct 18 2008 ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname BR2 ! boot-start-marker boot-end-marker ! enable password cisco ! no aaa new-model ! resource policy ! memory-size iomem 15 network-clock-participate slot 1 voice-card 1 dspfarm dsp services dspfarm ! ip cef ! ! no ip dhcp use vrf connected ip dhcp excluded-address 10.130.0.1 10.130.0.99 ip dhcp excluded-address 10.130.0.120 10.130.0.254 ! ip dhcp pool ITS network 10.130.0.0 255.255.255.0 option 150 ip 10.130.0.1 default-router 10.130.0.1 ! ! no ip domain lookup ! ! stcapp ccm-group 1 ! isdn switch-type primary-net5 ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip ! ! ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference 3 g729r8 ! ! ! ! ! ! ! ! --More-- Oct 18 04:18:16.407: h323chan_chn_process_read_socket: fd=2 of type CONNECTED has data voice translation-rule 1000 rule 1 /^76301/ /1/ ! voice translation-rule 7630 rule 1 /^1/ /76301/ ! ! voice translation-profile 4digits translate called 1000 ! voice translation-profile 8digitout translate calling 7630 ! ! ! ! ! ! controller E1 1/0 pri-group timeslots 1-3,16 ! controller E1 1/1 ! ! ! ! ! interface Loopback0 ip address 10.10.32.3 255.255.255.255 ip ospf network point-to-point h323-gateway voip interface h323-gateway voip id ccm ipaddr 10.10.32.1 1719 h323-gateway voip tech-prefix 1 h323-gateway voip bind srcaddr 10.10.32.3 ! interface FastEthernet0/0 no ip address duplex auto speed auto ! interface FastEthernet0/0.30 description BR2 Data Vlan 30 encapsulation dot1Q 30 native ip address 10.30.0.1 255.255.255.0 no snmp trap link-status ! interface FastEthernet0/0.130 description BR2 Voice Vlan 130 encapsulation dot1Q 130 ip address 10.130.0.1 255.255.255.0 no snmp trap link-status ! interface Serial0/0 no ip address encapsulation frame-relay IETF no fair-queue frame-relay lmi-type ansi ! interface Serial0/0.1 point-to-point ip address 10.10.33.130 255.255.255.128 frame-relay interface-dlci 102 ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice voice no cdp enable ! interface Service-Engine2/0 ip unnumbered FastEthernet0/0.130 service-module ip address 10.130.0.2 255.255.255.0 service-module ip default-gateway 10.130.0.1 ! router ospf 1 log-adjacency-changes network 10.10.32.3 0.0.0.0 area 0 network 10.10.33.128 0.0.0.127 area 0 network 10.30.0.0 0.0.0.255 area 0 network 10.130.0.0 0.0.0.255 area 0 ! ip route 10.130.0.2 255.255.255.255 Service-Engine2/0 ! ! ip http server no ip http secure-server ip http path flash: --More-- Oct 18 04:19:01.435: h323chan_chn_process_read_socket: fd=2 of type CONNECTED has data ! ! ! ! tftp-server flash:P003-07-4-00.bin tftp-server flash:P003-07-4-00.sbn tftp-server flash:P00307020200.bin tftp-server flash:P00307020200.loads tftp-server flash:P00307020200.sb2 tftp-server flash:P00307020200.sbn tftp-server flash:P00403020214.bin ! control-plane ! ! ! voice-port 1/0:15 translation-profile incoming 4digits ! ccm-manager sccp local FastEthernet0/0.130 ! ! sccp local FastEthernet0/0.130 sccp sccp ccm 10.130.0.1 priority 1 sccp ip precedence 3 sccp mtp sessions 1 sccp codec g729ar8 mask sccp codec g729br8 mask sccp codec g729abr8 mask ! dspfarm transcoder maximum sessions 3 dspfarm confbridge maximum sessions 3 dspfarm codec g729 vad disable dspfarm ! ! dial-peer voice 1 pots incoming called-number . direct-inward-dial ! dial-peer voice 999 pots translation-profile outgoing 8digitout destination-pattern 999 port 1/0:15 forward-digits all ! dial-peer voice 1600 voip destination-pattern 1[126]00 voice-class codec 1 session protocol sipv2 session target ipv4:10.130.0.2 incoming called-number 1[126].. no vad ! dial-peer voice 2 voip voice-class codec 1 incoming called-number . ! gateway timer receive-rtp 1200 ! ! ! ! gatekeeper shutdown ! ! telephony-service load 7910 P00403020214 load 7960-7940 P00307020200 max-ephones 10 max-dn 15 ip source-address 10.130.0.1 port 2000 auto assign 1 to 2 service dnis dir-lookup timeouts interdigit 7 system message BR2 sdspfarm units 1 sdspfarm transcode sessions 1 sdspfarm tag 1 mtp001360f655a0 network-locale GB create cnf-files version-stamp Jan 01 2002 00:00:00 voicemail 1600 max-conferences 8 gain -6 moh flash:music-on-hold.au web admin system name admin
Re: [OSL | CCIE_Voice] problem with calls comming in via h323 to CME, can't reach CUE(busy)
It was enabled, removed it, no change. Thanks anyway Med venlig hilsen Flemming Ortvald Network System Eng. NetDesign A/S +45 7241 4346 From: chunmei chen [mailto:[EMAIL PROTECTED] Sent: 23. oktober 2008 00:13 To: Flemming Ortvald Subject: Re: [OSL | CCIE_Voice] problem with calls comming in via h323 to CME, can't reach CUE(busy) Have you selected Wait for Far End H.245 Terminal Capability Set on H323 Trunk, if so you may want to disable it. --- On Wed, 10/22/08, Flemming Ortvald [EMAIL PROTECTED] wrote: From: Flemming Ortvald [EMAIL PROTECTED] Subject: [OSL | CCIE_Voice] problem with calls comming in via h323 to CME, can't reach CUE(busy) To: ccie_voice@onlinestudylist.com Date: Wednesday, October 22, 2008, 2:39 PM Doing this scenario: CCM -- h323trunk -- GK -- CME -- ephone OK PSTN -- CME -- CUE OK CCM -- h323trunk -- GK -- CME -- CUE fails Regardless of selected codec. Any suggestions? Config from CME router: Current configuration : 6164 bytes ! ! Last configuration change at 04:09:53 UTC Sat Oct 18 2008 ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname BR2 ! boot-start-marker boot-end-marker ! enable password cisco ! no aaa new-model ! resource policy ! memory-size iomem 15 network-clock-participate slot 1 voice-card 1 dspfarm dsp services dspfarm ! ip cef ! ! no ip dhcp use vrf connected ip dhcp excluded-address 10.130.0.1 10.130.0.99 ip dhcp excluded-address 10.130.0.120 10.130.0.254 ! ip dhcp pool ITS network 10.130.0.0 255.255.255.0 option 150 ip 10.130.0.1 default-router 10.130.0.1 ! ! no ip domain lookup ! ! stcapp ccm-group 1 ! isdn switch-type primary-net5 ! ! ! voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip ! ! ! voice class codec 1 codec preference 1 g711ulaw codec preference 2 g711alaw codec preference 3 g729r8 ! ! ! ! ! ! ! ! --More-- Oct 18 04:18:16.407: h323chan_chn_process_read_socket: fd=2 of type CONNECTED has data voice translation-rule 1000 rule 1 /^76301/ /1/ ! voice translation-rule 7630 rule 1 /^1/ /76301/ ! ! voice translation-profile 4digits translate called 1000 ! voice translation-profile 8digitout translate calling 7630 ! ! ! ! ! ! controller E1 1/0 pri-group timeslots 1-3,16 ! controller E1 1/1 ! ! ! ! ! interface Loopback0 ip address 10.10.32.3 255.255.255.255 ip ospf network point-to-point h323-gateway voip interface h323-gateway voip id ccm ipaddr 10.10.32.1 1719 h323-gateway voip tech-prefix 1 h323-gateway voip bind srcaddr 10.10.32.3 ! interface FastEthernet0/0 no ip address duplex auto speed auto ! interface FastEthernet0/0.30 description BR2 Data Vlan 30 encapsulation dot1Q 30 native ip address 10.30.0.1 255.255.255.0 no snmp trap link-status ! interface FastEthernet0/0.130 description BR2 Voice Vlan 130 encapsulation dot1Q 130 ip address 10.130.0.1 255.255.255.0 no snmp trap link-status ! interface Serial0/0 no ip address encapsulation frame-relay IETF no fair-queue frame-relay lmi-type ansi ! interface Serial0/0.1 point-to-point ip address 10.10.33.130 255.255.255.128 frame-relay interface-dlci 102 ! interface FastEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial1/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice voice no cdp enable ! interface Service-Engine2/0 ip unnumbered FastEthernet0/0.130 service-module ip address 10.130.0.2 255.255.255.0 service-module ip default-gateway 10.130.0.1 ! router ospf 1 log-adjacency-changes network 10.10.32.3 0.0.0.0 area 0 network 10.10.33.128 0.0.0.127 area 0 network 10.30.0.0 0.0.0.255 area 0 network 10.130.0.0 0.0.0.255 area 0 ! ip route 10.130.0.2 255.255.255.255 Service-Engine2/0 ! ! ip http server no ip http secure-server ip http path flash: --More-- Oct 18 04:19:01.435: h323chan_chn_process_read_socket: fd=2 of type CONNECTED has data ! ! ! ! tftp-server flash:P003-07-4-00.bin tftp-server flash:P003-07-4-00.sbn tftp-server flash:P00307020200.bin tftp-server flash:P00307020200.loads tftp-server flash:P00307020200.sb2 tftp-server flash:P00307020200.sbn tftp-server flash:P00403020214.bin ! control-plane ! ! ! voice-port 1/0:15 translation-profile incoming 4digits ! ccm-manager sccp local FastEthernet0/0.130 ! ! sccp local FastEthernet0/0.130 sccp sccp ccm 10.130.0.1 priority 1 sccp ip precedence 3 sccp mtp sessions 1 sccp codec g729ar8 mask sccp codec g729br8 mask sccp codec g729abr8 mask ! dspfarm transcoder maximum sessions 3 dspfarm confbridge maximum sessions 3 dspfarm codec g729 vad disable dspfarm ! ! dial-peer voice 1 pots incoming called-number . direct-inward-dial ! dial-peer voice 999 pots translation-profile outgoing 8digitout destination-pattern 999 port 1/0:15 forward-digits all ! dial-peer voice 1600 voip destination-pattern 1[126]00
