7xxx-series port adapters PA-MC-xT1 do have integrated CSU/DSUs.
Contrast with 16xx/26xx/36xx-series network modules NM-xFEyCT1 and
NM-xFEyCT1-CSU where you have to specify with or without.
Not sure about the discontinued CX-MIP cards; hope that's not what you're
looking for.
-Gabriel
ACS, and the IOS config guides for
security and AAA, I was able to pass first try by a non-scary margin.
-Gabriel
**NOTE: New CCNA/CCDA List has been formed. For more information go to
http://www.groupstudy.com/list/Associates.html
_
UPDATED Posting Guidelines: ht
<[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
>
>
> Hello Group,
>
> is it possible and does it work, whenn I place two Gigabit-Ethernet ports,
one
> Fast-Etjernet port and one OC3 port in a 7507 router?
http://www.cisco.com/cgi-bin/front.x/config_root.pl for
is *not* supported in the IP Only feature
set, and that it *is* supported in the Enterprise feature set for most of
the low-to-mid grade routers. Not sure about IP Plus, Desktop, or other
medium-feature grades.
-Gabriel
**NOTE: New CCNA/CCDA List has been formed. For more information g
tween vlan?
Assuming 2 VLANs numbers 1 and 2, make sure you have "bridge irb", "bridge 1
route IP", "bridge 2 route IP", "int bvi 1" with appropriate IP address, and
"int bvi 2" with appropriate IP address all configured.
I've had no end of trou
"Priscilla Oppenheimer" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Where did these questions come from? Please specify the source (book,
etc.)
> so that we know we aren't disobeying the NDA and giving you answers from
an
> actual test. These sure sound lik
Your instructor is confusing FECN/BECN with Discard-Eligible.
""Miller, Nathan (AZ15)"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I have received conflicting answers to this question from a number of
> sources to include a Cisco Certified Instructor in a
<[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
>
>I have my DSL line in right now, is there any labs I can do using DSL
with
> my 5 Cisco router? they are (4) 25XX and (1) 4000...
Not unless you also have a DSL-to-(something else most likely Ethernet)
brid
I know it seems counter-intuitive, but you might try looking through that
output for such important codewords as "memory", "flash" and "non-volatile".
"Study Cisco" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi All,
>
> Could you tell me actually what is t
""Cthulu, CCIE Candidate"" <[EMAIL PROTECTED]> wrote in message
8qb0n2$cip$[EMAIL PROTECTED]">news:8qb0n2$cip$[EMAIL PROTECTED]...
>
> Anyways, I am going to learn it, adn learn it good. My question is: can
I
> set up any of the interfaces to dynamically acquire an IP address via
DHCP?
> I want
http://www.cisco.com/partner/visio/ if you have a Partner-grade CCO login.
Also, if you're a partner, check out http://www.cisco.com/partner/cnd/ for
the Cisco Network Designer tool which does Visio-style diagrams plus can
generate complete bills of materials, pricing, and more; trick is you have
Also, and importantly: While ISL tags *all* frames with VLAN info, 802.1Q
does *not*: Traffic on the "native" VLAN is forwarded unaltered. So, an
802.1Q trunk will not work at all if the native VLANs are not identical,
whereas an ISL trunk can if nothing goes wrong.
-Gabriel McCall,
2500s: fixed ports, slower, cheaper
2600s: modular ports, faster, more expensive
If you're only going to use the router in one role and you don't need the
performance, get a 2500. If you want to be able to use the router with
multiple interface types in multiple scenarios, get a newer more modula
""¡Shawn.!"" <[EMAIL PROTECTED]> wrote in message
8q7lvt$16d$[EMAIL PROTECTED]">news:8q7lvt$16d$[EMAIL PROTECTED]...
> 100 Base T uses 2 pair (CAT 5)
Technically "100baseTX", no? I thought "100baseT" was a generic term
referring to either TX or T4. I'd also really like to know what the official
<[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> HP 100VG was a short lived 100 mbps networking technology that used all
> eight wires. This enabled it to even run over category 3 cable as long as
> none of the wires was being used for phone services.
Ah, 100V
""alex campbell"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hello all,
>
> I have a cisco 2620 router...running IOS 12.0, I have also just got a 4T
> serial card,
> every time I power up the router...I get the message 'Unspecified Card in
> Port 1'.
> I h
"Mohamed Abdallah" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hello,
>
>
> I have a Cisco Router 2501 ( One Ethernet + Two Sync. serial ports )
> I want to connect one its serial port ( NON ISDN port ) to ISDN BRI
> line provided by the our PTT
>
>
> Does
""Ejay Hire"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Where can I find out what the newest version of the IOS software and
> End-of-life product like a 3202 router will run?
www.cisco.com, "Software Center", "Cisco IOS Upgrade Planner". CCO Login
requi
""Hubert Pun"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi
>
> what does the "access-list 100 permit ip host 0.0.0.0 host 0.0.0.0"
> applied to an interface do?
I can't think that it would do anything useful. The "host" keyword means
"match all bits", s
They have a copyright issue page at
http://www.samw.com/global/legal_statements.asp? , however; the fact that
they even have such a page is bad news. I'd probably bypass their procedure
and just email their lawyer with the news that you're informing *your*
lawyer, and see what happens.
"Priscilla
examples of what you're trying to do or
what your environment is?
-Gabriel McCall, CCDP/CCNP+Sec
""EXT-Crosby, David M"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I am looking for real life examples of layer 2
y and
large is an excellent tool.
It doesn't let you configure an NM-1FE into a 26xx, though, even though it's
a working configuration.
-Gabriel McCall, CCDP/CCNP+Sec
""Chuck Larrieu"" <[EMAIL PROTECTED]> wrote in message
008401c01ab8$94deade0$[EMAIL PROT
h thing.
You should have done something like this:
6509-1> (enable) set password consolepass
> Usage: set password
6509-1> (enable) set password
> Enter old password:
etc.
Hope this helps...
Gabriel McCall, CCDP/CCNP+Sec
""Lists Wizard"" <[EMAIL PROTECTED
In a static topology, there's no need for a dynamic routing protocol. Only
when the lack of flexibility and slow (manual) reconfiguration become issues
do you need to think about routing protocols. For a simple, stable network,
use static routes.
-Gabriel McCall, CCDP/CCNP+Sec
"jeo
You can, and it does work, but it's not a Cisco-supported configuration. I'm
guessing because of backplane/ throughput issues, but I've never heard any
official explanation.
I've verified this with NM-1FE's... haven't tried with the new FE/WIC
modules.
-Gabriel
does support the SPEED
command, but if you have a 2-port ethernet module it's definitely just
10mbps.
-Gabriel McCall, CCDP/CCNP+Sec
""Lonnie Paschall"" <[EMAIL PROTECTED]> wrote in message
8pj5mq$fbn$[EMAIL PROTECTED]">news:8pj5mq$fbn$[EMAIL PROTECTED]...
>
No problems here. Problem's on your side.
""g_study"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I have been trying to go to http://www.cisco.com for about 4 days an it
> apears to be down. Is anyone else having any problems?
>
> **NOTE: New CCNA/CCDA List
e MSFC Sup, I can get a
good router with serial ports for a lot less than the FlexWan card plus port
adapter.
-Gabriel McCall, CCDP/CCNP+Sec
**NOTE: New CCNA/CCDA List has been formed. For more information go to
http://www.groupstudy.com/list/Associates.html
_
UPDAT
http://www.cisco.com/univercd/cc/td/doc/pcat/2500.htm
<[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
>
> Folks,
> Someone kindly furnish me with the details(part number e.t.c.) of
> the DRAM required for upgrading a 2500, any useful info will be
app
rvers...
CAB-OCTAL-ASYNC has RJ-45s; CAB-OCTAL-MODEM has DB-25's, and CAB-OCTAL-KIT
has RJ-45s and includes DB-25 adapters.
Getting the right cable for your application always helps. =)
-Gabriel
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/gu
""David R. Lease"" <[EMAIL PROTECTED]> wrote in message
01cd01bfd6c0$36d8b560$[EMAIL PROTECTED]">news:01cd01bfd6c0$36d8b560$[EMAIL PROTECTED]...
> We have five very competent folks maintaining and expanding a
> client's network. A CCIE, two CCNPs, an MCSE + CCNP, and a
> MCSE+I.
>
> Last week, h
d at
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat5000/rel_4_3/cmdref/d
_cmd.htm#22633 )
That should fix it.
-Gabriel
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
"Sammi" <[EMAIL PROTECTED]> wrote in message
news:[EMAIL PROTECTED]...
> Hi all,
> I would like to obtain the 30-day evaluation of Cisco Centri
firewall.
Product discontinued August 1998:
http://www.cisco.com/warp/public/cc/cisco/mkt/gen/bulletin/security/78
6_pp.htm
If you need a NT-platform s
o
be what you wind up with in that case, or a 12000 if you really need lots of
routed gigabit.
If you just need switched gig, get a 3508 or a 4912.
-Gabriel McCall
CCDP/CCNP+Security
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list ar
t... Thanks in
advance.
Gabriel McCall
CCDP/CCNP+Security
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.groupstudy.com
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Or use control-P for "P"revious command... control-N ("N"ext) is the
same as the down-arrow.
There's probably a way to cnfigure HyperTerminal so the arrows work
properly, but I just always use the control-codes for cursor movement.
""Douglas James Howe"" <[EMAIL PROTECTED]> wrote in message
8it7
""Chen, Frank"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> We are going to upgrade our PIX1 to PIX520. But the sales not only
from
> agent but Cisco told us we could not transfer our original license to the
> new equipment. We have to trade in our PI
"MATTHEW BRINSFIELD" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I have 2 Sylvan Prometric vouchers good for taking the CCIE written test.
> This test costs $200.00 to take at a Sylvan testing center. I am willing
to
> sell both for $300.00, or will sell s
Shouldn't it, for maximum elegance, be "Permit 0.0.0.0 255.255.255.254"? Not
that it winds up mattering, but "2" is the 7th bit of the octet, not the
8th; it'll be wildcarded out. Any even number would work, of course; what
matters is that the last bit is 0 not 1.
> -Original Message-
>
Or heat... intermittent failures can often be resolved to a heat-sensitive
connection somewhere along the way, especially if your problems show up in
the summer but not winter.
"Daniel Cotts" <[EMAIL PROTECTED]> wrote in message
303479FA060CD211B893F805A88A5E38CE@EXCHANGE1">news:303479FA060CD
""Shahir Boshra"" <[EMAIL PROTECTED]> wrote in message
8jetug$6j7$[EMAIL PROTECTED]">news:8jetug$6j7$[EMAIL PROTECTED]...
> I sent this reply some days ago, but never found its way to the group.
>
> Well, apparently this is a punctuation error, they were comparing
> "encapsulated SNA priority" wi
but it doesnt go into the
router config mode. i know for dlsw i have to get an IBM featured IOS and
for ipx there is another IOS. is there any IOS which features isis, dlsw
and ipx in one image?
any information or URLs to this issue would be greatly appreciated,
gabriel
_
Suaveguru,
The community attribute is a way to group destinations in a certain community and
apply routing decisions (accept, prefer,
redistribute, etc.) according to those communities.
Please read the BGP case studies section 2 example:
http://www.cisco.com/warp/public/459/14.html
gabriel
Hi group,
i would appreciate if someone could roughly estimate the amount and depth of Appletalk
knowledge one has to have for the CIT test.
Thanks in advance,
gabriel
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
suggestions what the reason for the high "not a gateway" output might be?
thanks in advance,
Gabriel
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
and
debugs is a must.
The resources: CIT book by Chappell/Farkas, Boson #2, Priscillas flash cards and the
list.
Any suggestions how to start preparing for the CCIE written? I just started reading
Doyle's book..
gabriel
_
FAQ, list archives, and subscrip
locker of the Z3?
Relax, its just a piece of paper.
gabriel
CCNP :-)
- Original Message -
From: "REMI IBIDUNNI" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Wednesday, December 06, 2000 8:47 AM
Subject: CCNP
>
> Folks,
> Can someone tell m
t the
bandwidth left ?
(i am thinking on something but i'm not sure)
Thank you
-------
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco Certified Network Professional
Cisco Certified Design Associate
S&T Romania
tel: +401 20 40 300
fax:
Hello
I found the "neighbor" option in my routers under "router eigrp..." but i
found no info on what that might do
Does anybody know ?
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco Certified Networ
?
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco Certified Network Professional
Cisco Certified Design Associate
S&T Romania
tel: +401 20 40 300
fax: +401 20 40 310
---
> -Original Message-
> From: Javier Contreras [SMTP:[EMAIL
steps to make a 2610 boot from tftp ?
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco Certified Network Professional
Cisco Certified Design Associate
S&T Romania
tel: +401 20 40
Hello,
if you configure policy routing to route certain packets through interface
S0
is there a way to automatically redirect packets through interface S1 if S0
is down ?
thanks,
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco
this is basic setup :-)
i'm thinking on something more complicated so i want to keep policy routing
:-)
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco Certified Network Professional
Cisco Certified Design Associate
S&T Ro
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco Certified Network Professional
Cisco Certified Design Associate
S&T Romania
tel: +401 20 40 300
fax: +401 20 40 310
---
> -Original Message-
> From: Brian [SMTP:[EMAIL
the CCIE LAN switching book:
-CGMP/IGMP
-VTP
-L3 switching
-VLAN
-Trunking (no ATM, no FDDI)
-STP
Combined with the Boson Test, would that be enough to pass the exam?
Gabriel
> Please advice me .
> BTW,I use ACRC courebook and CCO, Is that enough covering the whole exam
> objective
6/147).
hope this helps,
Gabriel
- Original Message -
From: "sniffer" <[EMAIL PROTECTED]>
Newsgroups: groupstudy.cisco
To: <[EMAIL PROTECTED]>
Sent: Thursday, October 12, 2000 1:04 PM
Subject: dynamic vlan membership
> hi, everyone
> I have a question about the d
Hi group,
i checked the CCO but found nothing on this subject. Is there an IOS command to
configure a 2924XL switch to use
cut-through/store-and-forward/etc. switching?
thanks in advance,
Gabriel
_
FAQ, list archives, and subscription info: http
commands
- no ATM, FDDI, VMPS
I used the Ciscopress LAN switching book by Clark/Hamilton and some CCO stuff. COLT
was usefull to identify my weak areas.
50% NP now and still a looong way to go...
Thanks to everyone for keeping the list lively.
Gabriel
_
FAQ, list
Hi group
Got a question regarding compression:
Can a Cisco 800, 1720 or 2620 (without AIM) provide ppp (payload)compression for a
2mbit serial line? I dont know if the processor
is able to handle this...
I would appreciate answers from the practical viewpoint.
thanks in advance,
Gabriel
""Brad Ellis"" <[EMAIL PROTECTED]> wrote in message
8ug2vr$kgp$[EMAIL PROTECTED]">news:8ug2vr$kgp$[EMAIL PROTECTED]...
> Also, I believe you can NOT use a WIC-2T in a 36xx router.
>
> -Brad Ellis
> CCIE#5796
> [EMAIL PROTECTED]
You can't use a WIC-2T in the older NM-1E2W modules; however, the ne
A !H indicates that the router at that hop doesn't know anything about the target
address; the packet comes back to the source with
a message saying "No Forwarding Address".
gabriel
- Original Message -
From: "Jason yee" <[EMAIL PROTECTED]>
To:
be before ALL traffic exceeds the rate limit
gabriel
- Original Message -
From: "Yee, Jason" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Tuesday, November 21, 2000 7:20 AM
Subject: access-list for DDOS attack
>
>
> hi ,
>
> Anyone knows wh
Boson #1 and COLT test and read the Ciscopress BCRAN book by Paquet (except
for the chapter dealing with the 700's). The
list, off course, is also a great resource.
gabriel
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
R
Hi there,
i am looking for config samples for an IPSec setup between a cisco =
(1720) router and a linux box with NAT enabled on both devices.=20
any advice is welcome,
gabriel
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
/iosplanner.cgi?
get_crypto=&data_from=&hardware_name=1720&software_name=&release_name=&majorR
el=12.1&state=:HW
any idea why there is no IPSec 3DES 12.1 IOS in the download center?
Is the VPN module needed for 128k bandwidth or can the CPU handle the
software encryption on a 1720 ?
th
published april 15. i found the first volume to be excellent but what about
the second?
is the bgp part as good as halabis 2nd edition?
thanks,
gabriel
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=1688&t=1688
--
F
WS-X5213A, would this
module be sufficient?
thanks in advance,
gabriel
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=5885&t=5885
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.htm
this is the small document that may help you a lot
regards,
Gabriel Barrios
INVENSYS PROCESS SYSTEMS VENEZUELA
T: 58-212-2675868 ext. 105
F: 58-212-2670964
M: 58-416-8.235171
C: [EMAIL PROTECTED]
-Original Message-
From: Larry Brown [mailto:[EMAIL PROTECTED]]
Sent: Wednesday
8.448
E3 480 34.368
E4 1.920 139.264
T1 24 1.544
T2 96 6.312
T3 672 44.736
T4 4.032 274.176
i expect this may help a little...:-)
Regards,
Gabriel
Gabriel Barrios
INVENSYS PROCESS SYSTEMS VENEZUELA
T: 58-212-2675868 ext. 1
just type:
#conf t
#no service config
^Z
#copy run start
this will disable looking for configs
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco product manager, CCNA, CCDA
S&T Romania
tel: +401 20 40 300
fax: +401 20 40
hello
in 3 hours i will go for the CIT exam. anybody has last minutte advices ?
10x
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco product manager, CCNA, CCDA
S&T Romania
tel: +401 20 40 300
fax: +401 20 40
ntact me.
Thank you,
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco product manager, CCNP, CCDA
S&T Romania
tel: +401 20 40 300
fax: +401 20 40 310
---
__
there is a 30 min. extension for the non-english natives.
The difference may come from there.
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco product manager, CCNP, CCDA
S&T Romania
tel: +401 20 40 300
fax: +401 20 40
but couldnt find any l2tp&vpdn (we need both
running on this machine) feature for this
platform.
TIA,
Gabriel Nickel
Hello
I have a
line aux 0
transport input all
that works ok for my terminal server;
the only thing you should be careful about is to check for the async line
number assigned to the AUX line ( use #sh line)
Good luck
---
Gabriel Neagoe, GN379-RIPE
what do "#show line" result ?
-------
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco product manager, CCNP, CCDA
S&T Romania
tel: +401 20 40 300
fax: +401 20 40 310
---
>
Hello,
is there any serious interest in an irc
channel dedicated to those who study for their ccnp 2.0?
I am taking BSCN in 2 weeks or
so...
/Gabriel
understanding the packets chose this path because of the eBGP administrative
distance (20). Do we have to decrease the OSPF distance to >20? In addition
static routing is not desirable (there would be too many networks to
announce).
Any input would be much
appreciated,
Gabriel
as a part of many ospf sample
configurations frame relay is used. is a detailed knowledge of frame
relay required for BSCN or are the basics sufficient?
thanks for any input
/gabriel
Please could someone clarify the difference between IOS "T" and non-"T" releases ?
Thanks in advance,
/gabriel
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://www.g
usually
:-)
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco product manager, CCNP, CCDA
S&T Romania
tel: +401 20 40 300
fax: +401 20 40 310
---
> -Original Message-
>
ts it receives) ; i'm
thinking on this beacuse of a practical case with thousands of subnets
announced through BGP by an unpolite peer, and there is not a good idea to
filter the routes received.
Regards,
-------
Gabriel Neagoe, GN379-RIPE
Networking
Hello,
I think is best to use only one address, and do BGP to your ISPs (moving DNS
inside your network is a good idea also).
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
CCNP, CCDA
S&T Romania
tel: +401 20 40 300
fax: +401 2
the
memory and put it in the router
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
CCNP, CCDA
S&T Romania
tel: +401 20 40 300
fax: +401 20 40 310
---
> -Original Message-
> F
fibers and they can offer one wavelength to you.
-------
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
CCNP, CCDA
S&T Romania
tel: +401 20 40 300
fax: +401 20 40 310
---
> -Original Message--
what do "sh ip bgp sum" and "sh ip bgp nei" produce ?
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
CCNP, CCDA
S&T Romania
tel: +401 20 40 300
fax: +401 20 40 310
Guide for EIGRP, OSPF and BGP. BGP Case Studies
/gabriel
**NOTE: New CCNA/CCDA List has been formed. For more information go to
http://www.groupstudy.com/list/Associates.html
_
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives
Hi group!
Has anyone read both the BCMSN book by Cisco Press and McGraw-Hill and can comment on
these? after reading the amazon reviews i
still dont know which one to buy...
thanks in advance
/gabriel
**NOTE: New CCNA/CCDA List has been formed. For more information go to
http
ccess-list 101 indicates an extended access list. the syntax is:
access-list {number} {permit|deny} {protocol} {source} {destination} {port}
one any for the source and one for the destination.
HTH,
gabriel
___
UPDATED Posting Guidelines: http://www.groupstudy.com/
ding of the IOS 12.1 BGP Config Guide plus the BGP part of the
Large Scale IP Networks Design Guide from the Cisco Docu sufficient for the BSCN
BGP part? Any input would be appreciated.
Thanks,
Gabriel
HEllo everybody
I have just passed Foundation routing & switching exam ( it was tough ) and
I am heading for CIT.
What are the best materials to study for CIT ?
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco product man
could this happen because you have to use a crossover cable between the hub
and the switch ?
or
are there any VLANs on the catalyst ?
---
Gabriel Neagoe, GN379-RIPE
Networking solutions consultant
Cisco product manager, CCNA, CCDA
S&T Romania
ICIT content that has two OCTET_STRING !!!
Can anybody help me?
Thanks, Gabi.
--
-----
Gabriel Lopez Millan - Grupo ANTS-CIRCuS
Facultad de Informatica
Universidad de Murcia (Espaqa) Tfo: +34 968367645
Message Posted at:
http://www.groupstudy.com
My own answer :-))
The problem was that envelopedData is signed with user Certificate, not with
self Signed
Certificate.
Cheers, Gabi.
Gabriel Lopez Millan escribis:
> Hi all. I think it's a offtopic question, but I need help !!
>
> I'm deploy a SCEP Server to work with
: failed to set self auth context
1w3d: %SYS-3-HARIKARI: Process Crypto PKI RECV top-level routine exited
What's mean ? !!
Thanks in advance
--
-
Gabriel Lopez Millan - Grupo ANTS-CIRCuS
Facultad de Informatica
Universidad de Murcia (Espaqa) Tfo
95 matches
Mail list logo