Does anyone know what model microphone Frank is using for SSB around the
0:30 mark?
On Mon, May 30, 2016 at 3:49 PM Peter Pauly wrote:
> https://www.youtube.com/watch?v=0ORBxLV72n4
> __
> Elecraft mailing list
> Home:
All,
I found it convenient to program the PF2 key to toggle the ATU/THRU function
with one button push. I have the PF1 key programmed as DUAL WATCH during the
winter months for Fox hunts and programmed as RX Preamp in summer for Field ops.
Myron WVØHPrinted on Recycled Data Original
Hi Tom:
There is a menu setting for the ATU which lets you put it in BYPass.
The AlexLoop is tuned manually. It’s pretty easy: with your KX3 set to the
operating band of choice, simply tune the tuning knob on the antenna until you
hear a peak in background noise. It’s very pronounced, so
On Mon,5/30/2016 5:36 PM, Ron Castro wrote:
Is there some reason why I should do this differently?
Yes. When you turn the K3 off with its power switch, it writes current
conditions to its RAM. When you turn it back on, it loads those
settings. When you drop power to the K3, that write
Hi Just a note...the next release due in June will support the SDRPLAY dongle
as a Panadapter. The SDRPLAY will offer a maximum spectral bandwidth of 1.8
Mhz, unlike the 192 kHz displays of other Panadapters. In addition, there will
be no need for a sound card with this device. Look for it
On 5/30/2016 8:36 PM, Ron Castro wrote:
I'm setting my K3 up at a remote facility where I can turn the 12 VDC power
supply on and off remotely, but if I turn it off, the K3 shuts down and
can't be started without using the Remote Power On/Off on pin 8 of the ACC
connector. My question: Since I
Re "Try it with 1 KW, it will really surprise
you. And sadly, I don't think a Reynolds Wrap hat
will protect you if you're close.: Not to worry,
because the AlexLoop would fail very quickly if
subjected to a kW! I'd not want to be under it or
anywhere near it in that case.
73, Phil W7OX
Please read and study the microKEYER II Users Manual!
All PTT inputs (PTT port, 2nd PTT Port, WinKey PTT, Foot switch, mic
PTT, etc.) are in parallel (just like the K3). The PTT Outputs are
selected on the PTT Tab in microHAM Router - with PTT1 being the PTT
connector on the mic cable and PTT2
I'm setting my K3 up at a remote facility where I can turn the 12 VDC power
supply on and off remotely, but if I turn it off, the K3 shuts down and
can't be started without using the Remote Power On/Off on pin 8 of the ACC
connector. My question: Since I will be using the power supply to turn
Thanks for the feedback Fred. So I'll have to turn off the internal KX3 ATU?
How do I do that?
Also have you seen or read anything on the Chameleon F loop? I saw a few things
on You Tube. Similar to the Alex Loop.
Doesn't the Alex Loop tune itself?
73
Tom
W1PDI
Sent from my iPhone
> On May
On Mon,5/30/2016 12:09 PM, Dan - VA3MA wrote:
When one makes it personal
Dan,
My apology if you were offended. Perhaps you're new to Elecraft. Many of
us began buying their radios when they only sold kits, and everyone
built their own. Indeed, many of us OTs built Heathkits. Elecraft
Hi Tom,
Yes, I have had good success with the Alex Loop on PSK-31 using 3 to 5
watts out from a high rise condo while on vacation. Bands I used was 20
& 17 meters. I have not had much luck on SSB or CW no matter what
antenna I used because of too much steel, concrete & man made noise.
The
I replaced my Buddipole with an Alex and use it a lot in the field ...
understand that as I accumulate birthdays, "field" more and more means a
drive-to a park or friendly hill. It works better than the BP ever did,
I can set it up in 5 min, it is fairly insensitive to ground and
surrounding
On 5/30/2016 7:27 PM, Jim Rodenkirch wrote:
Wayne/Eric: I do lots of "runs" during contests and after completing a CQ run
and waiting for the "next cycle" I find, often, when a station returns my
CQ, if I hit a dit key to cancel the "beacon mode," the calling station
stops sending (he heard my
I've been successfully running JT-65, WSPR this weekend on my KX2 @ 2.6 Watts
and monitoring the PA temp on the VFO B display. The ambient temp in the shack
was about 21C, at the end of the WSPR Tx cycles the PA Temp gets up to about
58C. (20m, 30m, 40m frequency does not seem to matter). Look
I have tried the MFJ 1788 MagLoop and the TW2010. Both are good choices. The
Magloop is good for up to a bit more than 100 watts. The TW2010 is better made
and easier to operate and will handle a full gallon. Both are portable but the
TW2010 is light and rugged.
Ramón E. Tristani Sr. NQ9V
Has anyone had much success using either an Alex Loop or Chameleon P Loop
antenna with their KX3? I have few antenna options in an apartment situation
and throwing a 25 foot long wire into a nearby tree has not worked for me.
Even tried loading up a 33 foot long aluminum balcony railing with no
Wayne/Eric: I do lots of "runs" during contests and after completing a CQ run
and waiting for the "next cycle" I find, often, when a station returns my
CQ, if I hit a dit key to cancel the "beacon mode," the calling station
stops sending (he heard my dit and 'pauses').
Could sumpin' be done,
https://www.youtube.com/watch?v=0ORBxLV72n4
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
> I've gone through the CONFIG and Menu and changed things, including
> upping the output number, while listening on earbuds plugged to the
> LINE OUT, but an hearing nothing.
Try powered (amplified) speakers ... the Line Out may not have enough
"oomph" to drive ear buds.
> Am I missing some
My K3 is not putting anything out on the rear panel LINE OUT connector.
I've gone through the CONFIG and Menu and changed things, including
upping the output number, while listening on earbuds plugged to the
LINE OUT, but an hearing nothing. Am I missing some config item?
Dave, W5UN
Don't worry Joe, the FT817 fanboys will just add 160m and 6m on top of 2m/70cm
to the list of bands that the KX2 doesn't support :-) Meanwhile the rest of us
will be on air having fun making contacts with our fine easy-to-use Elecraft
gear;-)
73, Matt VK2RQ
On Mon, May 30, 2016 at 9:04 AM
I disconnected my PX3 and KX3 from my KXPA100 to take on a SOTA activation.
When I returned I connected everything as it was before, and when I try to
turn on the KXPA100 from the KX3 "PA Mode" to on, the amp will not turn on,
and after a few seconds the PA Mode goes to off. I disconnect the PX3
Elecraft is looking for some booth help for the following two upcoming
shoes:
*SeaPac in Seaside Oregon: June 4th and 5th. **
*
*HamCom in Irving Texas June 10th and 11th. *
Any time you are able to give us will be great, hopefully 2 hours at a
time if possible. Saturday mornings are the
Thanks for the reply Joe,, I didn't explain very well.
I am trying to work with Airlink express, I have com6 set on PTT2 on the
router, (com6 shows on the router as open). PTT1 is none (no com port)
And com6 for RTS on Airlink setup.
Going to transmit a red triangle comes up on com6, but only
Edward
Your test results are much appreciated! Any very informative!
Thank you kind sir
Would be interesting to be able to compare a newer KX3 with rev E boards to
your past test results
73
Dan
> On May 30, 2016, at 2:05 PM, Edward R Cole wrote:
>
> I ran extensive
Jim
When one makes it personal
I'm done
Have a happy day and enjoy ham radio
72
> On May 30, 2016, at 1:24 PM, Jim Brown wrote:
>
>> On Mon,5/30/2016 4:50 AM, D Howard wrote:
>> I thought at the price I paid for the KX3 I shouldn't have to do the
>> compensation
Thanks to everyone wh o wroke and helped me. It is TX'ing again. I had TX set
on the SL too low, turned it up and Bingo!
Thanks again to everyone.
Dcik N5XRD
__
Elecraft mailing list
Home:
I ran extensive frequency drift measurements on the KX3 in 2014,
purchasing an aftermarket heat sink for my KX3. After running the
temperature compensation procedure I reported:
I re-ran the JT65 testing sequences to measure frequency drift
after temperature compensation was done.
On Mon,5/30/2016 4:50 AM, D Howard wrote:
I thought at the price I paid for the KX3 I shouldn't have to do the
compensation nor run the KX3 at such reduced power once compensated. My trusty
old FT817 worked fine.
That's your problem, not Elecraft's. The KX3 was specifically designed
as a
Elecraft does not do the extended temperature comp because it would add too
much to the price of the radio for a feature that only a few people need.
I’m surprised when people buy a KX3, then are upset that it performs to its
specs instead of performing much better than specified. Both the
Perhaps you meant to emphasize there's no " as small a rig on the market as
the KX2," Joe
I own a KX3 and expect it has more "features" than the KX2 and it's nearly
"as portable" as the KX2looking at a K3S ad believe it has more features
as well..agree?
Jim R.
--
View this message
Howdy Fellow Elecrafters:
As I anxiously wait for my KX2 to arrive I'd like to congratulate Wayne and
Eric for hitting this one out of the ball park.
I don't believe there is another QRP rig on the market that can compare feature
for feature with the new KX2.
In any event the KX2 will be my
The KRC2 I listed earlier today has been sold.
Dick, K8ZTT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
What KX3 serial numbers have the new Rev. E board?
Rob
KA5QQA
KX3
K2
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list
Wayne/et al:
I run JT9 and JT65 with my KX3 often on 160 and 80...I had the temperature
compensation performed at the factory when I purchased the rig and I utilize
a cooling fan when running the JT modes or running a freq during a contest;
I loaded Dimension 4 s/w for extra time stability. No
I have a KRC2 band decoder and control kit for sale; asking $80 plus shipping
(USA).
Am selling the KRC2 because I have 12 mono band antennas (6M - 160M plus 75M
NVIS) and the KRC2 will only control 10 (10M - 160M). Doing a bit of research
(actually blind luck when perusing the Array Solutions
I upgraded my K3 from the 2.7khz 5 pole filters to the 2.8khz 8 pole
filters.
I have two 2.7khz filters available. Make me an offer if you need them.
Rich - N5ZC
__
Elecraft mailing list
Home:
David
Can't agree more with what you say about the KX3 !
The KX3 is a superb piece of engineering
In my circumstances as apartment dweller with very limited antenna options -
WSJT modes allow me to still operate and make QSO's - thanks Joe Taylor!
In other circumstances there wouldn't be an
Using Airlink Express (or any other digital program) I can get the
PTT LED on the Microham to come on but it doesnt bring the k3 into
tx.
*Which PTT LED?* There are two PTT LEDs on microKEYER II (PTT1 which
is the mic PTT and PTT2 which is the ACC jack PTT) and one on the K3.
As documented
Fair enough, I am very happy with my KX3, a third party heatsink made it work
for me on digital modes at the power I need. I mainly use it on 144 MHz
currently with an external transverter. I actually enjoyed doing the
temperature compensation procedure, it was fun.
The 817 is a nice all in
Wayne
As Lyle mentions in his email for the KX2 - it would be helpful if someone
(Elecraft?) would measure the stability of the new revE KX3 in WSJT modes and
post the results.
Hopefully resulting in increased sales!
Thanks for your comments
73
Dan VA3MA
> On May 30, 2016, at 12:43 AM, Wayne
David
I thought at the price I paid for the KX3 I shouldn't have to do the
compensation nor run the KX3 at such reduced power once compensated. My trusty
old FT817 worked fine.
I also assumed Elecraft would address the issue with an updated KX3 -ie an
'KX3s' at some point.
So I sold it
I am using a very similar combination (K3, LP-Pan/LP-Bridge/NaP3, Xonar U5)
and I have successfully recorded received audio with Audacity. You didn't
mention what sound card you were using for audio recording, but you cannot
use the same sound card for audio that NaP3 is using with the LP-Pan. I
Dan ,
I am surprised that you couldn't get WSJT to go with your KX3 and had to sell
it.
I am using my KX3 (note not a KX2) on WSJT on 144 MHz EME JT65b. I did however
do the extended temperature VFO compensation first and that perhaps is a key
requirement. The KX3 was actually more stable
Advice please, I have the Microham working on receive, but I cannot get the
transmission side going for digital modes.
Using Airlink Express (or any other digital program) I can get the PTT LED on
the Microham to come on
but it doesnt bring the k3 into tx.
I have plugged the microham into the
46 matches
Mail list logo