Hi Bill, I just tried to use Q65 with “Cumulative" selected as you suggested. However, the problem is still there as described below. I have to shut down my transceiver (Elecraft K3S) to get it to stop transmitting.
Thanks, John WA1EAZ > On Mar 6, 2021, at 8:44 AM, Bill Somerville <g4...@classdesign.com> wrote: > > Hi John, > > I am not sure as I have not investigated this issue yet. It is easy enough to > check, select "Cumulative" for the 2D spectrum display, restart WSJT-X, and > see if the iusse goes away. > > 73 > Bill > G4WJS. > > On 06/03/2021 13:25, John Stengrevics wrote: >> Hi Bill, >> >> Will this fix solve the problem I reported yesterday with OS Big Sur? I’ll >> repost below in case you didn’t see it. >> >> Thanks, >> >> John >> WA1EAZ >> >> Repost - some additions in red: >> >> John & Joe, >> >> I had been using the previous version successfully on a MacBook Pro (Intel >> not M1) OS Big Sur 11.2.2. >> >> Today, I downloaded Mac version 2.4.0-rc2. >> >> When running Q65, T/R = 30 seconds, Submode A, the program continues to >> transmit after the 30 second period is complete for 60 seconds total. >> However, it does not seem to drive my amplifier after 30 seconds. [PTT is >> activated for the second 30 seconds, but no audio to drive the amp.] I have >> since tried FT8 on WSJT-X and can confirm that it works as usual. Thus, the >> problem seems to be isolated to Q65. >> >> I did follow the instructions in the Readme file. >> >> If there is a file I can send you, please let me know. >> >> I would appreciate any suggestions you can provide. >> >> Best 73, >> >> John >> WA1EAZ >> >>> On Mar 6, 2021, at 5:55 AM, Bill Somerville <g4...@classdesign.com >>> <mailto:g4...@classdesign.com>> wrote: >>> >>> Hi Dave and Kevin, >>> >>> we have finally tracked down the cause of this crash, thanks for your >>> patience it was not so easy to track down. It is repaired for the next >>> release, for now if you do not use of the Q65_Sync Wide Graph >>> synchronization plot the crash will be avoided. Note this is not a Mac >>> specific issue although it does seem to have the most severe effects on >>> that platform. >>> >>> 73 >>> Bill >>> G4WJS. >>> >>> On 06/03/2021 03:59, David Schmocker wrote: >>>> Hello all, >>>> >>>> A second report that mirrors this one: WSJT-X 2.4.0rc2 >>>> >>>> OS 10.14.6, Mac Mini >>>> >>>> Mode Q65, Waterfall Q65_ Sync selected and slow to let go of PTT line >>>> to K3S radio (even after Tx period). (when I go into Radio Panel, the >>>> Test PTT Red bar stays on, won't easily release). >>>> >>>> Then when a decode should take place, I get a crash exactly as Kevin >>>> reported with the same exact message as reported below. >>>> >>>> Thank you, 73, >>>> >>>> Dave KJ9I >>>> >>>> >>>> >>>> On 3/5/21, 8:47 PM, "Kevin McQuiggin"<mcqui...@sfu.ca >>>> <mailto:mcqui...@sfu.ca>> wrote: >>>> >>>> Hi All: >>>> I tried submitting this earlier today, but it didn’t seem to make to >>>> the list. Hence, a re-submission: >>>> >>>> Just trying out RC2 on an iMac, MacOS version 10.14.6 Mojave. >>>> >>>> Selection of “Q65_Sync” from dropdown box on the wide graph causes a >>>> crash as soon as the application starts to TX. Selection of “Cumulative” >>>> (the default) and TX/RX are normal. >>>> >>>> Specific exception was "EXC_BAD_ACCESS (SIGSEGV)”. >>>> >>>> I have saved the crash dump and can provide as necessary. >>>> >>>> 73, >>>> >>>> Kevin VE7ZD > > _______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel
