Hi Bill, I can’t find the ~/Library/Preferences/ directory in which to put the file. Can you provide a bit more detail on how I can locate it? Sorry.
John WA1EAZ > On Mar 6, 2021, at 9:20 AM, Bill Somerville <g4...@classdesign.com> wrote: > > Hi John, > > so I can see what is happening put the attached file into the WSJT-X > configuration files directory (~/Library/Preferences/ on macOS), restart > WSJT-X, run a minimal test to demonstrate the issue, then quit WSJT-X (do not > turn off the rig until WSJT-X has exited). There will be a new file on your > Desktop called WSJT-X_RigControl.log, send me that file for analysis please > (g4wjs <at> classdesign <dot> com)? > > Once you have sent me the log file delete the wsjtx_log_config.ini and > WSJT-X_RigControl.log files to resume normal operation. > > 73 > Bill > G4WJS. > > On 06/03/2021 14:13, John Stengrevics wrote: >> Bill, >> >> I have CAT selected and it does connect when I click on Test. >> >> John (G4KLA) had asked what driver I was using. I replied that the driver >> had not changed. It has always been /dev/cu.usbserial-A503XYAO. >> >> John >> WA1EAZ >> >>> On Mar 6, 2021, at 9:07 AM, Bill Somerville <g4...@classdesign.com >>> <mailto:g4...@classdesign.com>> wrote: >>> >>> Hi John, >>> >>> which option do you have checked for "Preferences->Radio->PTT Method"? >>> >>> 73 >>> Bill >>> G4WJS. >>> >>> On 06/03/2021 14:03, John Stengrevics wrote: >>>> Hi Bill, >>>> >>>> I just tried to use Q65 with “Cumulative" selected as you suggested. >>>> However, the problem is still there as described below. I have to shut >>>> down my transceiver (Elecraft K3S) to get it to stop transmitting. >>>> >>>> Thanks, >>>> >>>> John >>>> WA1EAZ >>>> >>>>> On Mar 6, 2021, at 8:44 AM, Bill Somerville <g4...@classdesign.com >>>>> <mailto:g4...@classdesign.com>> wrote: >>>>> >>>>> Hi John, >>>>> >>>>> I am not sure as I have not investigated this issue yet. It is easy >>>>> enough to check, select "Cumulative" for the 2D spectrum display, restart >>>>> WSJT-X, and see if the iusse goes away. >>>>> >>>>> 73 >>>>> Bill >>>>> G4WJS. >>>>> >>>>> On 06/03/2021 13:25, John Stengrevics wrote: >>>>>> Hi Bill, >>>>>> >>>>>> Will this fix solve the problem I reported yesterday with OS Big Sur? >>>>>> I’ll repost below in case you didn’t see it. >>>>>> >>>>>> Thanks, >>>>>> >>>>>> John >>>>>> WA1EAZ >>>>>> >>>>>> Repost - some additions in red: >>>>>> >>>>>> John & Joe, >>>>>> >>>>>> I had been using the previous version successfully on a MacBook Pro >>>>>> (Intel not M1) OS Big Sur 11.2.2. >>>>>> >>>>>> Today, I downloaded Mac version 2.4.0-rc2. >>>>>> >>>>>> When running Q65, T/R = 30 seconds, Submode A, the program continues to >>>>>> transmit after the 30 second period is complete for 60 seconds total. >>>>>> However, it does not seem to drive my amplifier after 30 seconds. [PTT >>>>>> is activated for the second 30 seconds, but no audio to drive the amp.] >>>>>> I have since tried FT8 on WSJT-X and can confirm that it works as usual. >>>>>> Thus, the problem seems to be isolated to Q65. >>>>>> >>>>>> I did follow the instructions in the Readme file. >>>>>> >>>>>> If there is a file I can send you, please let me know. >>>>>> >>>>>> I would appreciate any suggestions you can provide. >>>>>> >>>>>> Best 73, >>>>>> >>>>>> John >>>>>> WA1EAZ >>>>>> >>>>>>> On Mar 6, 2021, at 5:55 AM, Bill Somerville <g4...@classdesign.com >>>>>>> <mailto:g4...@classdesign.com>> wrote: >>>>>>> >>>>>>> Hi Dave and Kevin, >>>>>>> >>>>>>> we have finally tracked down the cause of this crash, thanks for your >>>>>>> patience it was not so easy to track down. It is repaired for the next >>>>>>> release, for now if you do not use of the Q65_Sync Wide Graph >>>>>>> synchronization plot the crash will be avoided. Note this is not a Mac >>>>>>> specific issue although it does seem to have the most severe effects on >>>>>>> that platform. >>>>>>> >>>>>>> 73 >>>>>>> Bill >>>>>>> G4WJS. >>>>>>> >>>>>>> On 06/03/2021 03:59, David Schmocker wrote: >>>>>>>> Hello all, >>>>>>>> >>>>>>>> A second report that mirrors this one: WSJT-X 2.4.0rc2 >>>>>>>> >>>>>>>> OS 10.14.6, Mac Mini >>>>>>>> >>>>>>>> Mode Q65, Waterfall Q65_ Sync selected and slow to let go of PTT >>>>>>>> line to K3S radio (even after Tx period). (when I go into Radio >>>>>>>> Panel, the Test PTT Red bar stays on, won't easily release). >>>>>>>> >>>>>>>> Then when a decode should take place, I get a crash exactly as Kevin >>>>>>>> reported with the same exact message as reported below. >>>>>>>> >>>>>>>> Thank you, 73, >>>>>>>> >>>>>>>> Dave KJ9I >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> On 3/5/21, 8:47 PM, "Kevin McQuiggin"<mcqui...@sfu.ca >>>>>>>> <mailto:mcqui...@sfu.ca>> wrote: >>>>>>>> >>>>>>>> Hi All: >>>>>>>> I tried submitting this earlier today, but it didn’t seem to make >>>>>>>> to the list. Hence, a re-submission: >>>>>>>> >>>>>>>> Just trying out RC2 on an iMac, MacOS version 10.14.6 Mojave. >>>>>>>> >>>>>>>> Selection of “Q65_Sync” from dropdown box on the wide graph causes >>>>>>>> a crash as soon as the application starts to TX. Selection of >>>>>>>> “Cumulative” (the default) and TX/RX are normal. >>>>>>>> >>>>>>>> Specific exception was "EXC_BAD_ACCESS (SIGSEGV)”. >>>>>>>> >>>>>>>> I have saved the crash dump and can provide as necessary. >>>>>>>> >>>>>>>> 73, >>>>>>>> >>>>>>>> Kevin VE7ZD > > <wsjtx_log_config.ini>_______________________________________________ > wsjt-devel mailing list > wsjt-devel@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/wsjt-devel
_______________________________________________ wsjt-devel mailing list wsjt-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/wsjt-devel