Hi Colby,
in answer to your enquiries.
1) You must have me confused with another poster as I don't have a
Dvorak keyboard.
2) I don't notice anything with any other programs for keystroke
recognition pauses, although there are few programs which I use them in.
Possibly Camtastic and GC Prevue a bit but not near as much as Protel.
3) Windows Accessibility nothing is enabled anywhere in the
accessibility options.
4) No special drivers for the Keypad.
5) Nobody monitoring my keystrokes, was mentioned many months ago but
has never happened. The MIS department does have some fancy back-up system
in place though which supposedly gives them "minute by minute" backups.
Brad Velander,
Lead PCB Designer,
Norsat International Inc.,
#300 - 4401 Still Creek Dr.,
Burnaby, B.C., V5C 6G9.
Tel. (604) 292-9089 direct
Fax (604) 292-9010
website www.norsat.com
> -----Original Message-----
> From: Colby - PowerStream [mailto:[EMAIL PROTECTED]]
> Sent: Monday, June 25, 2001 1:31 PM
> To: Protel EDA Forum
> Subject: Re: [PEDA] CLARIFICATION: Speed problem with Protel
> 99SE in PCB
> e ditor !
>
>
> Sorry Brad, no tricks this time :(
>
> I have been sitting here playing around with different
> settings trying to
> re-produce what you are seeing, but I cannot find the cause
> for nothin! I
> even tried switching to the Dvorak keyboard you talk about... no
> difference... my hotkeys are still immediate.
>
> Do you notice any sort of key delays in any other programs?
> Any programs that might be checking the keys before they make
> it to the
> programs? Windows Accessibility options?
> Any special drivers for your keyboard?
> Anyone spying on your keystrokes? hehe
>
> Biggest problem I have is that I don't have an NT system I
> can test this on
> :(
>
> Anyway, while we are here... here are a couple things that
> will help with
> other types of delays in Protel(and also other programs in
> Windows)... Most
> of you probably already know about this stuff... but it seemed an
> appropriate place to bring it up.
>
> (I think this is the same in NT, but I am not positive... any registry
> editing is always done at your own risk!)
> In your Registry under
> HKEY_CURRENT_USER\Control Panel\Desktop
>
> You can add a string value named MenuShowDelay and enter a
> value into it.
> If you enter the value 0 then all of your menu's will show up
> immediately
> when you hover your mouse over them. Add this string, then
> re-boot your
> machine and then access the start menu to see the difference.
>
> ------
>
> In your mouse settings you can alter the double-click speed
> and this will
> effect how some operations happen inside Protel, mainly
> regarding setting
> the focus on items when you 'tap-click'. eg. Tap click a
> track in PCB and
> it will show the handles(set the focus), Tap click a handle
> and it will drag
> that handle.
>
> If your Double-click speed is set to slow, then it will take
> more time for
> the focus to be set on an item, as it has to wait long enough
> to be sure you
> do not want to double-click
>
> If your Dbl-Click speed is set to fast then it will set the
> focus faster...
> if it is set REAL fast then it can sometimes be difficult to
> set the focus
> at all, because it has little time to determine if you are
> trying to pick
> the object up(click and hold) or set the focus(tap-click)
> -----
>
> Brad, have you modified/customized your menu's at all? I
> don't think this
> would slow it down, but it might be worth looking at.
>
> I am also assuming this only happens in PCB and not
> Schematic? is this
> right?
>
> I don't know that I can help but I am definitely curious as
> to why you are
> seeing so much of a delay.
>
> ----------------------------------------------------------------------
> Colby Siemer ** Custom Battery Chargers
> ** Custom Power Supplies
> PowerStream Technology ** Custom UPS
> 140 S. Mountainway Drive ** Custom DC/DC Converters
> Orem Utah 84058 ** Power management
> electronics for OEMs
>
> http://www.PowerStream.com
>
>
> ----- Original Message -----
> From: "Brad Velander" <[EMAIL PROTECTED]>
> To: "'Protel EDA Forum'" <[EMAIL PROTECTED]>
> Sent: Monday, June 25, 2001 12:49 PM
> Subject: Re: [PEDA] CLARIFICATION: Speed problem with Protel
> 99SE in PCB e
> ditor !
>
>
> > To anybody following this thread,
> > when reading some responses to my original post I realized that my
> > explanation might have been a bit lacking. The "pregnant
> pauses" that I
> see
> > are between the two keystrokes of certain commands, they
> are not after the
> > entry of the full command.
> > For instance I can press "X" to deselect, I get a significant pause,
> > then I get the secondary menu and I can press "A" for all.
> If I just press
> > "X" "A" in immediate sequence, I get the secondary menu
> showing up a few
> > seconds later and the program apparently didn't react to my
> "A" key stroke
> > and I have to enter the "A" again. Similarly I get the same
> response to
> > other two key shortcuts like "V" "R" for view redraw, "E"
> "M" "G" for move
> > polygon vertices (2 pregnant pauses) or "Z" "W" for zoom window. I
> probably
> > get them elsewhere as well but these are the operations I
> commonly use
> > shortcut keys to access rather then the toolbar buttons.
> > Therefore "I" conclude that this is not the usual pauses caused by
> > the analyzing net issues or other processing issues, as I
> believe that
> those
> > pauses occur only after and not between keystrokes of a
> single command
> > sequence.
> > Any comments Colby? I hope that you might have something up your
> > sleeve of tricks to point me in the right direction to a resolution.
> >
> > Brad Velander,
> > Lead PCB Designer,
> > Norsat International Inc.,
> > #300 - 4401 Still Creek Dr.,
> > Burnaby, B.C., V5C 6G9.
> > Tel. (604) 292-9089 direct
> > Fax (604) 292-9010
> > website www.norsat.com
> >
> >
> > > -----Original Message-----
> > > From: Mike Reagan [mailto:[EMAIL PROTECTED]]
> > > Sent: Friday, June 22, 2001 6:18 PM
> > > To: Protel EDA Forum
> > > Subject: Re: [PEDA] Re[2]: Speed problem with Protel 99SE in
> > > PCB editor
> > > !
> > >
> > >
> > > Brad,
> > > I was also experiencing long delays with NT 4 SP 5. I
> unloaded NT and
> > > jumped to 98 and my delay went away. I had been using NT
> > > for the past 4- 5
> > > years but have found better performance with Win 98. One
> > > of these days I
> > > will try one of the newer generation OS's.
> > >
> > >
> > > Mike Reagan
> > > EDSI
> > > Frederick MD
> >
>
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a message: mailto:[EMAIL PROTECTED]
*
* To leave this list visit:
* http://www.techservinc.com/protelusers/subscrib.html
* - or email -
* mailto:[EMAIL PROTECTED]?body=leave%20proteledaforum
*
* Contact the list manager:
* mailto:[EMAIL PROTECTED]
*
* Browse or Search previous postings:
* http://www.mail-archive.com/[email protected]
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
