pensive so trying to save a few dollars.
Joel
the duplexer, as when I use
a spectrum analyzer with a built-in tracking generator?
All comments will be appreciated, and set aside for the radio club here
archive.
v44kai.Joel.
Got you Don, thanks for responding.
But I'm looking for something more specific as to, how one may hook up, the
aforementioned equipment to do what the spectrum analyzer/with the TG does to
obtain a set of duplexer tuned to a specific frequency.
v44kai.Joel.
- Original Me
Skipp, thanks for responding.
All I want is a setup for the equipment I listed (NOTE: NO TG in none of the
unit, the 2955/A will do duplex) that will allow me to tune a duplexer, and
the procedure.
v44kai.Joel.
- Original Message -
From: "skipp025" <[EMAIL PROTECTE
re it still has its sensitivity
0.25 - 0.35uv, or better should be good. I will hate to touch the duplexer
without making sure that these other components are checked.
Hope you get fix, let us know what you find, when you do.
v44kai.Joel.
- Original Message -
From: John Transue
spec'd notch value.
>
> I did check these on the original freq and original factory cables
with same results
> Second:
> You might note the IFR 1600's generator output value and
> crank it up min 10dB and better yet 20 dB. Then have a second
> look...
&
Hi Chris, I agree with you, why suffer a whole class for a few IDIOTS, let the
IDIOTS stand in the cold without they jacket.
v44kai.Joel.
- Original Message -
From: Chris Carruba
To: Repeater-Builder@yahoogroups.com
Sent: Friday, September 12, 2008 5:27 AM
Subject: Re
What is your off list contact info?
v44kai.Joel.
- Original Message -
From: "Mike Mullarkey" <[EMAIL PROTECTED]>
To:
Sent: Wednesday, February 21, 2007 10:09 AM
Subject: [Repeater-Builder] Tektronics 492 Spectrum analyzer
> If anybody is looking for a re
Hello group I am in need of a 10 volt reg card for a ge station if
anyone wants to part with a extra one contact me off list at
[EMAIL PROTECTED] dot com
thanks kj4si
Joel
uning, and tuning helical.
v44kai.Joel.
From: "skipp025" <[EMAIL PROTECTED]>
To:
Sent: Monday, April 23, 2007 10:49 AM
Subject: [Repeater-Builder] Re: Service Monitors (Amtronix)
> Per my previous posts about HP Service Monitors...
>
> Amtronix also comes with
ected volt. (this should be in the leakage test mode)
I also will like to know the ring voltage at the different ring points (this
should be in the ring test mode)
I will be posting this on other groups, so you see it somewhere else.
Thank you all for your help in advanced.
v44kai.Joel.
Hi folks,
I want to thank all who responded to post with intent to help, especially
Marvin, Jim, and Denny, all of on different groups, for getting me the
manual, and the various readings I was interested in, and the contact info I
needed.
v44kai.Joel.
ke to get this controller going again, now that I got
the repeater TX and RX going, any help will be greatly appreciated.
v44kai.Joel.
Hi Bob,
I thought that may be the other way out, but, know nothing about programming
proms nor have a programmer, nor anyone in my country to do such, do you know
someone capable off such, Bob? any help will be appreciated.
v44kai.Joel.
- Original Message -
From: [EMAIL
(or know who bought the company from
"John Bell" and who have it now that would be help) lying around, that may have
a different problem, and have no use for it, and will like to part with it, I'm
willing to make arrangement to get it.
v44kai.Joel.
- Original Messag
Hi folks, I'm in need of your help, in obtaining the schematic of the
programming / cloning cable for the IC-H16 to the IC-V200 radios.
Please note: This information will be posted on other sites as well.
Your help will be appreciated, thanks in advanced.
v44kai.Joel.
tance on this, can't find it, and will
like some insight on this.
v44kai.Joel.
- Original Message -
From: "Jeff DePolo" <[EMAIL PROTECTED]>
To:
Sent: Wednesday, August 29, 2007 10:39 AM
Subject: RE: RE: Re: Re: RE: [Repeater-Builder] Re: Duplexers
>> T
ers are setup to the test gear figures.
So, is the figurers always the right thing to work with, or they are just
guides for a Tech with a bad hearing?
v44kai.Joel.
- Original Message -
Fom: Jesse Lloyd
To: Repeater-Builder@yahoogroups.com
Sent: Wednesday, August 29, 200
caps on 2 of them and make sure to clean them up as much as
possible btw the cables where 10 inches long on all
Joel kj4si
> -Original Message-
> From: Repeater-Builder@yahoogroups.com
> [mailto:[EMAIL PROTECTED] On Behalf Of Mike Besemer
(WM4B)
> Sent: Monday, October 06, 2008
For some that have used a pll icom and direct injected disc audio into
pin #3 what is the normal amount of audio to get 5 khz deviation? I am
useing a 2c pll icom and it is taking about 3 volt p-p is that about
right?
BTW The audio sounds great! Joel
he 70-100 k uF @ 35v please let us know here.
v44kai.Joel.
- Original Message -
From: Com/Rad Inc
To: Repeater-Builder@yahoogroups.com
Sent: Monday, December 29, 2008 3:25 PM
Subject: [Repeater-Builder] High capacity capacitors
Hello Group
A little off subject but I
anybody got a few of these for a set of db 4062 duplexers that they
would like to sell?
thanks joel kj4si
does anybody know what type of lubication is on the plunger of these
cans?
can Anyone tell me the amount of isolation need on a set of duplexers to run a
GE vhf pll exciter with a 100 watt pa. The GE reciever .15 uv @20 db sinad?
power at 30 watts,50 watts 70 watts and 100 watts without desense
Thanks kj4si
n to borrow.
I don't know anything about this unit, someone was able to send me the
operating manual, he doesn't have a R2001D nor does he have the service manual.
My main concerns are the A13 card, before I start to check for other problems.
I will appreciate any help here, thanks in advanced.
v44kai.Joel.
Thanks Erick,
Can you tell me anything about the A13 card?
v44kai.Joel.
- Original Message -
From: "Eric Lemmon"
To:
Sent: Tuesday, December 22, 2009 11:08 AM
Subject: RE: [Repeater-Builder] R2001D (A13) card
> Joel,
>
> FYI, the Maintenance Manual is pub
Thank you Erick,
v44kai.Joel.
- Original Message -
From: "Eric Lemmon"
To:
Sent: Tuesday, December 22, 2009 11:25 AM
Subject: RE: [Repeater-Builder] R2001D (A13) card
> Sorry, no. I have no knowledge of this equipment.
>
> 73, Eric Lemmon WB6FLY
>
>
Hi Bill,
Yes, that makes me feel better, I can now start to look at the SMPS, thanks
very much.
v44kai.Joel.
- Original Message -
From: william...@aol.com
To: Repeater-Builder@yahoogroups.com
Sent: Tuesday, December 22, 2009 12:43 PM
Subject: Re: [Repeater-Builder
It would be a great investment I have 2 (2955) a 2955, and a 2955A so the
2955B is much later beast than my 2 2955's I wish I had bought a 2955B or
2955R.
Take care that's all I can say for now.
v44kai.Joel.
- Original Message -
From: "Tedd Doda"
To:
Sent:
Hi to all here on the group,
Is anyone in the group know where I can get parts and boards for the
Motorola R2001D service monitor? I'm particularly interested in the A2 and
A7 boards.
v44kai.Joel.
--
I am using the free version of SPAMfighter.
We are a community of 7 million
We have 2 repeaters that are more or less the same. One is on 2 meters and the
other is on 440. They both exhibit the same problem, they lockup after a while
and then need to be power cycled. They ran for years without issue.
We have the Instruction manual for the Zentron controller, but nothin
Anybody have any reviews or maybe a used GMRS radio? I would like a 4 watt
radio. Is the FCC doing in with GMRS repeaters? Does anybody have them for
sale? Do they make a portable repeater?
Thanks for all the help. I received lots of great information.
--- In Repeater-Builder@yahoogroups.com, "Joel" wrote:
>
> Anybody have any reviews or maybe a used GMRS radio? I would like a 4 watt
> radio. Is the FCC doing in with GMRS repeaters? Does anybody have them for
&
>;
Sent: Tuesday, November 08, 2005 12:13 PM
Subject: Re: [Repeater-Builder] Alpha 2000 radio and AP4800 Rptr controller
>
>
> On 8 Nov 2005 at 19:14, v44kaiy wrote:
>
>> Hi one and all, my name is Joel and my call is v44kai I'm from St.
>> Kitts in the Caribbean.
you guys are right, never seen a RC-10 by MCC, but icom has a RC-10
controller at the link below, v44kai...Joel
http://www.usersmanualguide.com/icom/accesories__remote_controller
- Original Message -
From: "Gary Hoff" <[EMAIL PROTECTED]>
To:
Sent: Friday, December
Right off the rear connector Read about ¾ of the way down this page.
http://www.ccdx.org/zedyx/mods/ab_mod.htm
Joel - WA1ZYX
WebMaster for the Cheshire County DX ARC, Located at:
http://www.ccdx.org
http://www.ccdx.org> See Ya, Joel
[EM
Hope some of you guys that have some experince with db 4060 duplexer,the pass
is fine but the notch is the problem I can see the notch at around 35db on my
ifr 1600s per each can but when i combine them together about 50db is the best
i can get I have new cables made 1/4 wave long , the tuning c
skipp,
thanks for the idea. Do you have any suggestions as to which compay to order
a receiver from. Our repeater is near other repeaters and we don't want any rf
interference.
Joel
skipp025 <[EMAIL PROTECTED]> wrote:
As Jim pointed out... the problem(s) you report a
Is this what you're looking for?
http://www.ccdx.org/zedyx/mods/2TNCs1Radio.htm
on 123.0Hz
Please, if someone has a set they could part with, please email me "off list".
Thanks,
Joel - WA1ZYX
[EMAIL PROTECTED]
on 123.0Hz
Please, if someone has a set they could part with, please email me "off list".
Thanks,
Joel - WA1ZYX
[EMAIL PROTECTED]
If your controller has any logic outputs,config one to turn a external battry
charger on and if you have one with timers and such,program it to cut off when
battery is charged
Joel Hall
Kj4si
-
Never miss a thing. Make Yahoo your homepage.
Located at:
http://www.ccdx.org
<http://www.ccdx.org> See Ya, Joel
[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
or
WA1ZYX > K1XX DxCluster Node (Amateur Radio)
http://www.ccdx.org/zedyx/home.htm
<http:/
one of the guys talking into the BACK of the mic...
http://www.emergencyfans.com/images/page4-station51/hspose3-c.jpg
http://www.emergencyfans.com/images/index.htm
WebMaster for the Cheshire County DX ARC, Located at:
http://www.ccdx.org
See Ya, Joel
wa1..
na, but if your local DTV station has a
carrier frequency of 700Mhz and its analog counterpart was broadcasting
at 55Mhz, you're probably going to want a higher gain antenna, which the
UHF antennas typically are. And they are also much more directive. The
DTV "Channel" designators m
X ARC, Located at:
http://www.ccdx.org
See Ya, Joel
wa1...@ccdx.org
or
WA1ZYX > K1XX DxCluster Node (Amateur Radio)
http://www.ccdx.org/zedyx/home.htm
http://home.webryders.net/surry 443.800 141.3 K
Just wanted to say thanks for all replys
joel kj4si
I have seen before on a set of wacoms 641s that some one tuned the low input
for the high and the high for the low, it worked with only about 12 watts
input
Jeff...
Something similar to this?
http://www.ccdx.org/zedyx/mods/db212.htm
WebMaster for the Cheshire County DX ARC, Located at:
http://www.ccdx.org
See Ya, Joel
wa1...@ccdx.org
or
WA1ZYX > K1XX DxCluster Node (Amateur Ra
No, and no.
Your repeater would be putting out about 65 - 85 % of your 4 watts, based on
the type of duplexer setup.
v44kai.Joel.
- Original Message -
From: x.tait.tech
To: Repeater-Builder@yahoogroups.com
Sent: Friday, May 28, 2010 4:47 AM
Subject: Re: [Repeater
eep a roll in my
tool bag.
I hope this helped.
v44kai.Joel.
- Original Message -
From: "Doug Hutchison"
To:
Sent: Saturday, May 29, 2010 12:37 PM
Subject: [Repeater-Builder] Transformer cores
> Hello,
>
> Got situation where the 'elastic' or whate
You are welcome,
Just make sure you wind the tape the same way you would for the pipe thread
(right hand for tightening) so that when screwing it in the thread will seal
it, then taking it out wouldn't be a problem.
v44kai.Joel.
- Original Message -
From: "Doug Hutc
Very very good Doug,
It always work for me, never had to even undo one.
v44kai.Joel.
- Original Message -
From: "Doug Hutchison"
To:
Sent: Saturday, May 29, 2010 3:17 PM
Subject: Re: [Repeater-Builder] Transformer cores
> Yep, thought that might be a problem
I'd like to install a community tone panel on our group
repeater. I am considering the COM SPEC TP-3200 or the CONNECT
SYSTEMS TP-154.
Can any one reccommend which unit to use ?
TNX...Joel W4SLH
Yahoo! Groups Links
To visit your group on the web, go to
has a 42" face.
Any ideas will be appreciated.
TNX...Joel W4SLH
Yahoo! Groups Links
To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/
To unsubscribe from this group, send an email to:[EMAIL PROTECTED]
Your use of Yahoo! Groups is subject
LMR 400/600 cables
?
Is there a better cable for this purpose.
Thanks for your help and commects now and in the
past.
Joel W4SLH
Yahoo! Groups Links
To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/
To unsubscribe from this group, send an
e.
Maybe Steaven will convince the local utility to use a lower
rate.
Thanks again to all.
Joel W4SLH
Yahoo! Groups Links
To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/
To unsubscribe from this group, send an email to:[EMAIL PROTECTED]
Y
comments or info the
group might have concerning this equipment.
TNX...Joel W4SLH
Yahoo! Groups Links
To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/
To unsubscribe from this group, send an email to:[EMAIL PROTECTED]
Your use of Yahoo! Groups is
Good Morning:
Thanks to Kevin and Jim for their comments on Kendecomm
equipment. The information is greatly appreciated.
Can any one recommend a source for a Kenwood TKR-750
?
TNX...Joel W4SLH
Yahoo! Groups Links
To visit your group on the web, go to:http
Thanks to all who have responded to my inquiry about a Kenwood
TKR-750 repeater. As usual the information was extremely
helpful
Thanks again. Joel W4SLH
Yahoo! Groups Links
To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder
...Joel W4SLH
YAHOO! GROUPS LINKS
Visit your group "Repeater-Builder" on the web.
To unsubscribe from this group, send an email to: [EMAIL PROTECTED]
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
Here's some info on the Challenger stuff if you're interested...
http://www.ccdx.org/zedyx/mods/challenger.htm
73 de Joel - WA1ZYX
for the DB 228. The antenna is mounted at 500 feet and has been
through two hurricanes.
Regards...Joel W4SLH
Yahoo! Groups Links
To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/
To unsubscribe from this group, send an email to:[EMAIL
n" with 24+ dB of gain.
Thanks...Joel W4SLH
Yahoo! Groups Links
To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/
To unsubscribe from this group, send an email to:[EMAIL PROTECTED]
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
Thanks to all who replied to my Preamp question.
As usual, I gained valuable information ,ideas and
resources.
Regards...Joel
Yahoo! Groups Links
To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/
To unsubscribe from this group, send
Hope you'all may help on this
VHF 4 pole with it in omni config it has 6 db gain,all in one direction it has 9 db gain.
what I need to know if it is side mounted with all dipoles one direction what is the reduction in db at 180 degree?
Thanks Joel
Yahoo! Sports
Rekindle the Riva
@yahoogroups.com]On Behalf Of Dave VanHorn> Sent: Friday, June 17, 2005 7:09 PM> To: Repeater-Builder@yahoogroups.com; Repeater-Builder@yahoogroups.com> Subject: Re: [Repeater-Builder] 4-pole folded dipole ant.> > > At 06:38 PM 6/17/2005, Joel Hall wrote:> >Hope you
"run away" from the Flash Tech system
as fast as you can.
If you would like to discuss your problems, contact me direct
or call 252-249-2344
Regards...Joel, W4SLH
Pamlico Tower Leasing Co
- Original Message -
From:
Paul Finch
To: Repeater-Builder@yahoogroups.co
68 matches
Mail list logo