For this rig DATA-LSB, DATA-FM and DATA-FM-Narrow can be added but
> can’t think of any usable modes at the moment.
DATA-LSB would be appropriate for AFSK RTTY.
73,
... Joe, W4TV
On 2021-05-21 3:24 AM, ON4AOI wrote:
Hi All,
Yesterday Paul and I made the Yaesu FT-891 via USB working @
On 2021-05-13 3:24 AM, ON4AOI wrote:
It looks they (YAESU) didn't solve it yet and what is worse they
wrote that it's a 3th party error ??
On top of that, Yaesu claim to be working with third party developers
to resolve the issue. This is not correct with regard to microHAM (one
of the develope
On 2021-04-21 9:35 AM, ON4AOI wrote:
>
Or you have or buy a microHAM device that creates 2 CAT ports and can
use one @ 38400 baud for dx4win and the other @ 115200 baud for
wsjtx >
The two CAT ports for microHAM "keyers" (microHAM USB Device Router)
must be set to the same rate. The maximum
The new FTdx101 firmware has a bug in handling the mode command (at
least "get mode"). If DX4Win is using MD0;/MD1; to read mode of
VFO A and VFO B, it will not be able to read mode. I have not been
able to confirm if the problem extends to setting mode.
Recommendation: until Yaesu release a
Turn off the keyer in your transceiver!
73,
... Joe, W4TV
On 2020-01-17 7:31 PM, W9RPM wrote:
HI, I had Phil W1GEE make an cw Interface for me. Hooked it up. Using
Com10 with DTR for CW Keying, and RTS for PTT. It just sends Dits. Like
if I type "O" it sends 3 Dits. Confused as usual.
What are your Winkey settings in the CW Keyboard/WinKey settings?
The settings shown in the example configuration for MK II and Dx4Win
work properly with the demo (9.0.5.1221) and both MK II (Winkey v.10)
and MK III (WinKey v.30).
73,
... Joe, W4TV
On 2019-06-18 8:01 PM, Courtney Judd wr
Dave,
In Windows Device Manager -> Ports (COM & LPT) you associate a Legacy
LPT Port Number (LPT1, LPT2, or LPT3) with your PCIe LPT port (Port
Settings tab for that port). While N1MM+ uses the port address from the
Resources tab, DX4win uses the Legacy Port Number (LPT1, LPT2, or LPT3)
to ide
On 2018-12-16 8:16 AM, Ernie wrote:> Mark,
>
I have been using LP-Bridge to make all of the radio control stuff
play nice with my Yaesu for quite a while. Unfortunately it doesn't
list Icom as being supported, so probably not any help for you. If
DX4WIN would work with OmniRig, we would have ano
Actually, the only thing necessary is a utility to extract the list of
satellite names, start date and end date from the tQSL "config.xml"
file. Anyone with tQSL installed should have the current version of
config.xml (or can download/install it).
Allowing users to edit/add satellites will do n
/2018 9:49 AM, Paul F6EXV wrote:
By the time Kosovo declared independance, or was added to the US list of
independant states, it did not meet the criteria. It only meets the
criteria that was just added, so it is a discovery entity...
Le 23/01/2018 à 15:39, Joe Subich, W4TV a écrit :
Paul
, therefore starting date should be
the "discovery date", in this case the rule change.
If they count it retroactively, that means they do not understand their
own criteria (as they id for KH4 and KH7K recently... IMHO
73
Paul F6EXV
Le 23/01/2018 à 15:16, Joe Subich, W4TV a écrit :
> So I presume its ok this time but starting from this week only not b4
My internal source says, "immediately and *retroactive*". The interim
CEO is charged with drafting the new rules and determining the proper
"effective date". Most likely dates are 17 Feb 2008 (Declaration of
Independence)
How are you generating the CW? As far as I know, DX4Win supports only
one Winkeyer (either the DigiKeyer or DigiKeyer II). If you are not
using the Winkeyer, Windows is not a real time operating system and
CW (or FSK) generated using a software timer can contain significant
jitter/missing or st
rom my iPhone
On Nov 17, 2017, at 5:00 PM, Joe Subich, W4TV wrote:
except the keyboard the keyboard is only hot at the keys
now F functions don’t control anything in the logging program
I do not understand this statement. If you are talking abut the
computer keyboard - that you can
in the logging program
Do you still want me to go through the MicroKey II settings???
Thank you Bernie/WO2N.>
Sent from my iPhone
On Nov 17, 2017, at 3:23 PM, Joe Subich, W4TV wrote:
What transceiver are you using?
The CW window running MicroKey II winkey
In microHAM USB Device Router ...
What transceiver are you using?
> The CW window running MicroKey II winkey
In microHAM USB Device Router ...
1) make sure Router is reading the transceiver mode and
that the transceiver is in CW
2) Select the PTT tab - is there a *BLACK* box around CW
in the PTT Selector?
3) Se
John,
Windows 10 treats *.chm (compiled help files) as executable.
Use Windows Explorer to navigate to the folder containing the
help file, right click on the help file and make sure the
file is "unblocked".
73,
... Joe, W4TV
On 10/22/2017 5:09 PM, John, K9EL wrote:
Must be a local issue
JTAlert is logging already direct with : DXLab- HRD - Log4OM - AClog,
with this new updating of DX4Win WSJT-X is a MUST
In order for JTAlert to log directly to D4Win, you will need to convince
Laurie, VK3AMA to add that capability. To do so, he requires two things
- a documented API for insert
> If you added mode mappings to the Trusted QSL software, you may want
> to remove those too. How to do this is beyond the scope of the DX4WIN
> reflector.
Open tQSL
Select File ->Display or Modify Preferences
Select the ADIF Modes tab
Select each temporary mapping (e.g., FAX -> DATA, FT8 -> DA
On 8/11/2016 10:40 AM, Björn Ekelund wrote:
> If you use any of Microham's USB enabled units (CW keyers, TNC, rig
> controllers...) this functionality is built in.
Only microHAM "Keyer" series interfaces (microkeyer, microkeyer II,
digikeyer, digikeyer II, CW Keyer or MK2R+). USB Interface II a
set to "Microphone jack, DVK
Control" for voice?
Your symptoms indicate the audio is set improperly with the mic
routed *through* the sound card/computer. When MMTTY opens, the
sound card input is switched from mic to line disabling your audio.
73,
... Joe Subich, W4TV
microHAM Am
Is microHAM Router properly following the frequency and mode of your
transceiver?
What are the settings on the Audio Switching tab in microHAM Router?
Is the Voice/Digital settings selector set to "Use Voice Settings"?
Is "Computer generated audio fed to:" set to "Microphone jack, DVK
Control"
> 1. Where is the complete list of %macros?
Macro Commands List in the MITTY help file ("MITTY.chm").
Also the "commands" button in the MITTY macro editor (right
click on a macro to edit).
> the %X macro that starts transmission
There is no %X macro
> or the %M macro that I don't know the mean
The list software does not allow attachments. Put the file on your web
page and post a link to those who want it. If you do not have a place
for it, see if AD1C would put it with the rest of the rig files on his
site.
73,
... Joe, W4TV
On 3/11/2016 10:10 AM, RadioDen45 wrote:
Let see if
> Will USB to parallel port adapter work???
To the best of my knowledge *none* of the logging programs support
CW/PTT on a USB to *parallel port adapter*. The USB printer cables
typically use a special device driver to emulate a windows print
system and do not provide direct port access require
As documented in the original microKEYER Users Manual, there is
*NO VOX* in microKEYER. If you operate VOX you must connect the
"Send", PA Key, TX GND, etc. output of your transceiver to the
PTT input of your amplifier.
The original microKEYER has no way to know when the transceiver is
switched
has a split it SETS the SPLIT A B not
freq changes.
4. THE FREQ DOES NOTHING no changes.
So MODE is set, SPLIT mode is set, BUT no freq changes.
Cool.were getting somewhere.
I patiently wait your next instructions.
Bob
On 3/29/2015 9:43 AM, Joe Subich, W4TV wrote:
If you man no data at all
What function or functions did not work as expected?
73,
... Joe, W4TV
On 2015-03-27 1:32 PM, bob wrote:
Yes Sir,
I tried it. I think I'll compare the Ft-991xml file to the 3000.rig file
file see what happens/
Thanks for the input.
Bob
On 3/27/2015 9:27 AM, Joe Subich, W4TV
> ARE dx4win rig files XML files or something else.
DX4Win rig files are text based not XML.
Have you tried the FTdx3000 file on AD1C's web site:
http://dx4win.ad1c.us/radios/index.html ?
I do not have an FT-991 for testing it looks like it should work when
I compare that file to the CAT do
> so it is an issue with DX4WIN and microham router...
No, it is a configuration issue in DX4Win.
> The preference CW tab has Device type set to WinKey,
> Interface set to com4, external keyer set to com4.
You have configured *two devices* to the same port. Software CW keying/
PTT control and
ing in DX4WIN is
not working with the router... ideas? Cort
Joe Subich, W4TV <mailto:li...@subich.com>
Tuesday, February 03, 2015 9:00 AM
Cort,
As always, start with the example configuration for DX4Win and MK II
from microHAM. In Router (Help | Download Documents) or on-line i
It does not appear that any logs have been uploaded yet (to ClubLog).
When operating, it will show/list QSOs.
73,
... Joe, W4TV
On 2015-02-03 9:45 AM, Barry wrote:
There's a link at http://www.navassadx.com/ and click on AM I IN THE
LOG. I worked them last night and my QSO's not there yet
Cort,
As always, start with the example configuration for DX4Win and MK II
from microHAM. In Router (Help | Download Documents) or on-line in
the MK II area at www.microham-USA.com/support.html.
DX4Win's support for MMTTY is a bit strange in FSK in that you must
run MMTTY stand alone from the
The best start menu replacement for Windows 8/8.1 is Classic Shell
www.classicshell.net and is free. Properly configured the look/feel
is very close to either XP, Vista or Windows 7.
73,
... Joe, W4TV
On 2014-12-09 4:07 PM, David Christ wrote:
I have the same issue with Win 8. What prog
> Do you enabled the mic+lin : on
No! Do not use Mic+Line ... set MENU:MIC SEL to LINE while in DATA
mode (AFSK A, DATA A, etc.) and adjust the mic gain until you see
four to five bars of ALC while transmitting AFSK (see your K3 Owner's
Manual).
Also see example configurations for both MMT
You've mentioned how DXLab can take an ADIF file, but does that
include one's QSL status for each QSO?
Yes, if that status is exported according to the ADIF standard. ADIF
specifies QSL_SENT (I,R,Y,N), QSL_RCVD (I,R,Y,N), LotW_QSL_SENT,
LotW_QSL_RCVD, eQSL_QSL_SENT, and eQSL_QSL_RCVD.
In add
Amateur friend/colleague,
This comment has been filed with the FCC in support of ARRL's
disastrous and ill-advised rule making petition, RM-11708.
http://apps.fcc.gov/ecfs/document/view;jsessionid=1STjTgyJcfc05SL6R2c9hkP2lTNVFBzHGtPZkys3LGD7tW1xn2nT!1565474435!74404766?id=7521315143
While t
Remove the Pigknob and LP-Bridge from the equation and see if the
problem continues. It is entirely likely that two additional
processing stages cause enough delay that DX4Win is timing out.
73,
... Joe, W4TV
On 2014-06-06 12:07 PM, Howard K2HK wrote:
From: Howard K2HK
Date: June
You have a serious problem somewhere - LotW supports and tQSL allows
uploading:
ModeMode Group
CW CW
PHONE PHONE
IMAGE IMAGE
DATADATA
AM PHONE
FM PHONE
SSB PHONE
ATV IMAGE
FAX IMAGE
SSTVIMAGE
AMTOR DATA
CHIPDATA
CLOVER DATA
CONTESTIDATA
D
Actually, it would be extremely handy to have dual/dual receive -
MMTTY and 2-Tone on each the left and right channels of the sound
card to permit "listening in the pile-up" on split DX. It's not
difficult to do a separate instance of MMTTY for the sub RX/TX VFO
but it should be equally easy to
Tod,
You don't need to send either Title or "point value". That is
automatically calculated by LotW when the QSOs are uploaded.
LotW is the only way anyone can receive credit anyway - see:
http://www.arrl.org/centennial-qso-party
In order to compete in the Centennial Points Challenge, logs mu
t problem
> with the OMNI's DB25 to DB9 to my computer and thru RigBlaster
> (neither works. If you happen to have a contact name I would be
> grateful.
> Thanks for all the free work you do
> Mike - W7FKF
>
>
> --
>
> Message: 2
> D
Which model of RigBlaster and what is "not working"?
What functions - radio control, CW, PTT, FSK, etc. - are
you attempting to accomplish? Each RigBlaster model has
specific limits and none will do everything (at the same
time).
73,
... Joe, W4TV
On 12/12/2013 11:24 AM, Jim Reisert AD1C
Default address for the IC-706mkIIg is 58h.
Make sure DX4Win "baud" and Icom menu 35 CI-V Baud are the same.
Default value for Menu 35 is "auto" but DX4Win generally requires
a fixed value - so set menu 35 to the same value as you select for
"baud" (I prefer 9600 or 19200).
I have no informatio
The CW keying will not work. I still haven't been able remedy this. I
am told it has to do with developing virtual com-ports. I always used
lpt ports.
Did you install the LPT driver as shown in the help file? Search for
LPT Port Driver in the help.
CW keying works just fine with serial ports
Print it to a PDF printer like "PDF Creator" or save a subset of
the log (those columns you want to print) to a tab delimited text
file, open it with Open Office Writer and save to PDF.
There are other word processing programs that can also save as PDF
or "PDF Creator" installs a PDF printer tha
Did you reinstall the DX4Win LPT driver when you had to reinstall
DX4Win after the HD failure? See the LPT Driver topic in the
DX4Win Help file for more information - it is the first topic in
the list when you search the help file for LPT.
73,
... Joe, W4TV
On 11/2/2013 4:04 PM, John/K4WJ
George,
Is there a USB to RS232 (serial DB9) dongle out there that will do
this, model and where to buy?
There is no inexpensive USB to serial dongle that will do 45.45 baud
any more. All of the commodity USB to serial UART/Bridge makers have
changed to match the higher data rates of USB 2.0
Have you looked at the example configuration for USB Interface III
and DX4Win available in microHAM Router (Help | Download Documents)
or in the USB III area at www.microHAM-USA.com/support.html? It
contains all of the settings necessary ...
Note - with DX4Win you *must* set the CW PTT to VOX
My suggestion of how I like to log receive, transceive and transmit
frequencies has evolved over time, primarily in the age before
computer logging, when I wrote QSL cards out by hand and used
frequency rather than band.
Again, you are logging improperly. It may not matter to you as an
Amateu
> Proper logging of split frequency operation.
> The Frequency box should always be the receive
> frequency, i.e. the frequency that the DX is
> transmitting on. The QSX (transmit) frequency
> should be logged in a field separate from the
> current Frequency box only if operating split.
> (It is
ace?
With 2Tone I can decode S0 to S1 sigs. MMTTY needs S3 to S4 sigs to decode
accurately.
Dave, N4QS
-Original Message-
From: dx4win-boun...@mailman.qth.net [mailto:dx4win-boun...@mailman.qth.net]
On Behalf Of Joe Subich, W4TV
Sent: Thursday, October 10, 2013 1:19 PM
To: dx4win@mailm
2-Tone emulate the XMMT.ocx interface in MMTTY. DX4Win does not
use/support the XMMT.ocx interface so 2-Tone will not be usable
with DX4Win.
73,
... Joe, W4TV
On 10/10/2013 2:08 PM, Dave Perry, N4QS wrote:
Lee,
I would also like to use 2Tone with DX4WIN. It already runs great with
N1MM
ways helpful advice.
Mike, WM5DX.
____________
From: "Joe Subich, W4TV"
To: dx4win@mailman.qth.net
Sent: Wednesday, September 18, 2013 9:40 AM
Subject: Re: [Dx4win] Comports
I don't know if the new version of DX4WIN has been upgraded to
function with Win 8,
I don't know if the new version of DX4WIN has been upgraded to
function with Win 8, but it sounds like maybe not. I suggest you
talk to the DX4WIN guys about the problem. I checked the DX4WIN
> user group a while back and did not find any info on DX4WIN with
> Win 8. I continue to use my old ve
"USB to parallel" adapters are not port mapped devices and as such
they will not work with software like DX4Win that use direct port
writes. Unless you are using a laptop with no expansion bus, your
best solution is an add-on serial/parallel card for either PCI or
PCIe bus.
73,
... Joe, W4T
> how do i get that stuff up into LOTW from dx4win???
You don't. LotW will not accept non-amateur calls - period.
73,
... Joe, W4TV
On 7/8/2013 9:48 AM, bill steffey NY9H wrote:
just exported & tried to upload 181 files ,
tqsl bumped out the military crossband calls as not amateur c
110, Issue 29
Today's Topics:
1. PSK-31 Transmit Set-up (Bud Governale)
2. Re: PSK-31 Transmit Set-up (Joe Subich, W4TV)
Message: 2
Date: Sat, 29 Jun 2013 17:23:44 -0400
From: "Joe Subich, W4TV"
To: dx4win@mailman.qth.net
Subject: Re: [Dx4win] PSK-31 Transmit Set-up
M
How have you connected the computer to the K3?
The normal way to utilize the K3 is to use DATA A for PSK 31 with sound
card connected to the LINE IN jack and K3 set for LINE IN instead of
microphone. See your K3 Owners Manual for more information.
73,
... Joe, W4TV
On 6/29/2013 3:32 PM,
Does PSK-31 have a different audio-in path than RTTY which needs to
be set-up?
Audio input (sound card) is selected separately for RTTY (MMTTY) and
PSK31 (PSKCore). PSK31 sound card is selected in File | Preferences |
Control PSK Sound card (input) where RTTY sound card is selected in
RTTY C
__
De : "Radivoj Kar, F6GNZ"
À : "Joe Subich, W4TV" ; DX4WIN Refelector
Envoyé le : Lundi 24 juin 2013 8h26
Objet : Re: [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig
Thanks Joe ! I have created an additional port for COM2 and set Omni-rig to this
/OmniRig to the very minimum (slowest possible) to
prevent overloading the control channel between Router and the MK II.
73,
... Joe Subich, W4TV
microHAM America
http://www.microHAM-USA.com
http://groups.yahoo.com/group/microHAM
support e-mail: supp...@microham.com
the WinKey settings in the example.
73,
... Joe Subich, W4TV
microHAM America, LLC.
http://www.microHAM-USA.com
http://groups.yahoo.com/group/microHAM
supp...@microham.com
This message, including any attachments, may contain proprietary,
confidential or privileged
See the example configuration for DX4Win and USB Interface III
in the USB Interface II area at www.microHAM-USA.com/support.html
or in Router at Help | Download Documents.
Make sure the PSK31 window in DXLab Suite has selected "Speaker
(USB Audio CODEC)" as the transmit sound card and your trans
In the HELP file it states that LoTW will accept a ADIF and CABRILLO
file. I did not find any prompt about a tq8 file and figured it was
not needed in v1.14.1.
*READ* the help file again! From the first page of the Introduction:
TQSL accepts QSOs in a log file whose format is either ADIF or
Older versions of tQSL will also handle the newer digital modes if
you download the latest configuration file from the LotW web site
(log in, select "Your account", the "Your Certificates")
73,
... Joe, W4TV
On 6/3/2013 9:41 AM, Jim - N4ST wrote:
Another advantage of the newer TQSL progr
Unlike the older Yaesu rigs, Yaesu's new rigs require HANDSHAKE.
Without RTS high, the rig will not send data to the computer.
73,
... Joe, W4TV
On 4/17/2013 8:35 PM, James Simon wrote:
I just got a new FTDX-5000MP, replacing my FT-1000MP (on which I had
version 8.04), and upgraded to 8.0
> For the FT3K, this would probably work
Or one could use the same procedure as has been used for years with the
FT-990 and similar rigs by other software:
RC; - Clear Clarifier
MD#; - Set Mode
FA#; - Set Frequency (use "split" frequency)
AB; - move frequency/mode to VFO B
FA#;
) 539-5638
Grid: FM28lm
http://www.n3me.net
Elecraft K3 # 2462
PVRC Member
-----Original Message-
From: Joe Subich, W4TV [mailto:li...@subich.com]
Sent: Monday, February 18, 2013 22:31 PM
To: Tony McClenny; DX4WIN Reflector
Subject: Re: [Dx4win] Yaesu FT-450D
Tony,
What interface are you
Tony,
What interface are you using between the computer and radio?
The "new" Yaesu rigs expect RTS handshake - if you have a "real"
serial port or USB to serial converter with a cable that has all
9 wires set RTS="ON". If you don't have "all 9" - or at least
2-2, 3-3, 5-5, 7-7 and 8-8, go into
> But the processing delay is a month. Hold the applause.
Cool you jets! This happens every year in January and February.
The DXCC Desk stops processing LotW applications until they have
cleared all the paper applications from the previous year and
finalized the "end of the year" standings for
> It might do a few neat things like the automatic upload to LOTW,
> but the overall user interface is very poor. DX4WIN excels in many
> key areas such as its fast and reliable database, user ergonomics,
> integration with a wide variety of radios and assessories, etc.
I don't normally get into
> The ADIF spec has to be expanded to include award
> status flags, like the flags at the bottom of the DX4WIN QSO window,
> that are tracked separately from QSL status.
The ADIF Spec *has* been expanded to include "Credit_Granted" which is
a list of awards from an enumerated list for which the
> You can use your US certificate to apply for a Canadian one (which
> will be issued in less than a day in most cases), then you can create
> locations anywhere in Canada where you've operated.
And if you happen to sign W1ABC/R (for "Rover") or W9ZYX/0 and want to
use that with LotW you simply
Submitted
my "annual" update last evening at 8:40 and had all accredited at 9:49.
So some parts are working well
*Steve, N3SL*
Sioux City, IA
CQ4 ITU7 EN12
On Mon, Dec 10, 2012 at 3:09 PM, Joe Subich, W4TV wrote:
Delay keeps growing. Up to 8 days just a few minutes ago.
> Delay keeps growing. Up to 8 days just a few minutes ago.
Agreed - 8 days 14 hours! At the current rate of growth the
delay will be 9 days before tomorrow. Here are the latest
numbers I have:
Upload Time Time Processed Elapsed Time
Interesting ... If, in fact, the file was uploaded on November 25.
LotW processes in strict FIFO order so perhaps something happened to
"find" some of the lost uploads since normal processing has started
on uploads from December 1.
73,
... Joe, W4TV
On 12/7/2012 9:22 PM, N3SL wrote:
...a
Having been through this ...
Open the Help file and search for "LPT Driver"
Boot the computer using the F8 key to bypass driver signature
enforcement then run LPTDriver.exe in the "drivers" directory
of your DX4Win installation as *administrator* (right click,
run as administrator) to install t
Larry,
You're not the only one ... JL1NKC has not responded to at least three
requests for either 9J2KC or 9I40Z. I finally gave up and worked
9J2KK (who returned a card within two weeks). Unfortunately, 9J2KK
is QRT now.
73,
... Joe, W4TV
On 11/15/2012 7:43 PM, Larry Gauthier (K8UT) wr
On 9/25/2012 10:27 AM, PY2YP wrote:
> So the Z60K does count as YU. Am I right?
No, Z60K counts as *nothing* for DXCC. From the announcement:
>> will not count for any entity for DXCC awards purposes
Z6 counts as Kosovo for CQ DX and CQ Marathon.
73,
... Joe, W4TV
On 9/25/2012 10:27
What SO2R box are you using and how is it normally controlled?
73,
... Joe, W4TV
On 9/19/2012 4:43 PM, Michael Gulbranson wrote:
> Hi All:
>
> I need some help. My station is set up for SO2R contesting. I use DX4WIN
> as my general logging software. My issue is how do I toggle the rigs
On the other hand my log shows (by LotW only) Mixed: 1092, SSB: 469.
CW: 664, and Digital: 587. While LotW has Mixed: 1093, SSB: 469.
CW: 664. and Digital: 588 and has been that way for several days.
One item for some - you may need to link/merge accounts if you have
ever had multiple calls. Th
"microHAM Control Protocol" for OTRSP.
73,
... Joe Subich, W4TV
microHAM America, LLC.
http://www.microHAM-USA.com
http://groups.yahoo.com/group/microHAM
On 5/16/2012 9:45 AM, Jim Reisert AD1C wrote:
> While I can't comment on the PCIe-LPT card dire
I addition to what Bud has suggested, right click on the Computer icon,
Select Properties, click on "Device Manager", Open Universal Serial
Bus controllers, select *each* USB Root Hub and "Generic USB Hub"
entry, select the "Power Management" tab and *uncheck* the box marked
"Allow the computer t
What other Yaesu rigs? The new Yaesu rigs require handshake or at RTS
always on before they will respond to the computer (CAT).
73,
... Joe, W4TV
On 5/3/2012 8:49 PM, W9RPM wrote:
> I am not getting my 950 that I just got to work with DX4WIN. I have both
> set to 4800, and cable I am usin
> Works the same way as the microHAM router software without the need
> to get the microHAM interface. Acts like a old time 'TSR' program
> that sits in the background and does its thing like a traffic cop.
> Works great!
Unfortunately VSPE works nothing like a traffic cop (or microHAM
Router); i
> I can't tell if the application will let you upload multiple ADIF
> files, or if you only get one shot. Maybe someone who does this can
> add more details, and this can be added to the DXCC application
> note.
Yes, you can make multiple uploads ... subsequent uploads will replace
duplicated cou
On 3/26/2012 3:21 PM, Kostas Stamatis wrote:
> I believe it is relatively easy to make a homebrew interface to drive
> PW1 from an Ten Tec Orion ii. Orion ii (as i read in the manual) has
> band data in back side. I saw also that you can drive a relay for
> every band. So you can simply a voltage
r Manuals (available on the web
at www.microHAM-USA.com/downloads.html) in the "system" tab for MKII
and DKII and "PA Port" for Station Master. Generalized connection
diagrams for each of the options (please specify) are available from
i...@microham-usa.com.
73,
... Joe
> I can change output power and MMTTY display shows normal RTTY
> display at TX, but nobody answers my calls on their frequency !
Do you have another receiver to determine if you have set up the
FT-1000MP correctly? As shipped from Yaesu (default), almost all
Yaesu transceivers (including all mo
on might be just good enough for most people. I have seen
> MicroHAM products in action and they are very well thought out and supported.
> However, you are comparing a $50 kit with a $450 Cadillac …
>
> 73,
>
> Andreas, N6NU
>
>
> On Feb 28, 2012, at 8:01 AM, "
,
>
> You raise a very good point. K9JM's new gadget is not the only option
> for safe operation of a PW1. My update must include similar mention of
> microHAM and DXlabs solutions.
>
> -larry (K8UT)
> -Original Message- From: Joe Subich, W4TV
> Sent: Monday, Feb
optional CI-V output (as well as BCD amplifier
control) accessories to provide the same isolated CI-V bus capability.
In all cases the microHAM solutions are not limited to Icom rigs as
the auxiliary/isolated CI-V output is available with supported rig.
73,
... Joe Subich, W4TV
for the
feature and there will be no response to questions about
its use or future development.
73,
... Joe Subich, W4TV
microHAM America
http://www.microHAM-USA.com
http://groups.yahoo.com/group/microHAM
supp...@microham.com
___
of the
4 Pin RTTY input of the Mark V.
73,
... Joe Subich, W4TV
microHAM America, LLC.
www.microHAM-USA.com
> -Original Message-
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] On Behalf Of John Kjos
> Sent: Wednesday, November 16, 2005 1
uts can be used as inputs to a traditional
switch box.
73,
... Joe Subich, W4TV
microHAM America, LLC
www.microHAM-USA.com
96 matches
Mail list logo
