I should have mentioned in my earlier post that I use inverted vees
(picture a Maypole with fan dipole legs scattered around it) - which
means center supports holding up the feedline. That makes a light load
on the wires and much less stretching as opposed to supporting full
feedline weight
As I recall, I used pin 7 for the mic ground and pin 8 for the PTT
ground. In a brief test it worked ok into a dummy load. Is this not
correct?
That is correct although with the K3/K3S since the Elecraft mic RFI
change it should not matter (both pin 7 and pin 8 are connected to
the "ground"
This week I wired rewired my MicroHAM Micro2R cables for K3S's. As I
recall, I used pin 7 for the mic ground and pin 8 for the PTT ground. In a
brief test it worked ok into a dummy load. Is this not correct?
John KK9A
Bernhard.Horst at bmw.de Bernhard.Horst at bmw.de
Fri Feb 12 01:43:33 EST
Hello,
There is a new release of Win4K3Suite. This release adds a number of usability
enhancements for the K3, K3S and KX3 which include:
One button synchronization of the radio clock with the PC clock (!)
Addition of two presets in the ClubLog spotting wiondow allowing two sets of
band filters
I use a Heil PR 781 with great success. The K3S TX EQ is set as follows;
-16 dB @ 50 Hz, -12 dB @ 100 Hz, -6 dB @ 200 Hz, and 2400 Hz @ +3 Db,
3200 Hz @ +6 dB.
Working distance to the face of the mike is 4" to 5" on axis {one fist}
so as not to enhance bottom end due to proximity effect,
I have the K3S USB cable connected direct to one of the USB ports on the
computer. As to radio set-up, see page 33 of the manual for details. I
use DATA A mode for PSK & other data modes. The software is usually
FLDIGI, HRD/DM780 or WSJT-X which all work under Windows 10 successfully
and
K3s is coming next week. I have my existing K3 set up the way I like
to use it and have saved the configuration via the excellent utility.
The K3s is coming completed, I will immediately put the 100W module
and the ATU in place. I currently have a sub Rx in the K3, I will
move it to the K3s
My K3 1322 has an original KAT3 and firmware 5.38 2.86 1.25.
Last night I tried to use the LCSET feature of the KAT3 item on the
Configuration menu. I have used this successfully in the past, but no
luck this time.
I was able to make the L and C values show on the display, but rotating
the
I have K3 S/N 732 and use a $2 electret computer mic I bought at a yard sale.
They had a white one that was only a $1 but I chose to go the more expensive
route and buy the $2 black one to match the K3. My settings are -16db up to
400 Hz, 0dB at 800-1600 Hz, and +16 dB at 2400 up and I get
Got it working. W3FPR suggested downloading the FTID driver from the
Elecraft site. Everything is now working with the USB hookup - LP-Bridge,
K3, P3, KPA-500 (remote), SteppIR, DXBase, N1MM, AXETTY, MTTY.
Tnx for all the input.
N2TK, Tony
-Original Message-
From: Elecraft
Hi
I have noticed something strange with my K3 and am wondering whether it
is a bug, a feature or operator error.
I am using the K3 to send WSPR at 0.2W, band hopping but on almost
continuously on one band or another.
The driving program is WSTJ-X in WSPR2 mode with scheduling enabled.
The resounding answer has been NO, that I can't properly load the K3s
with my K3 setup.
Thank you all for the off-list replies.
73,
Gary
KA1J
> K3s is coming next week. I have my existing K3 set up the way I like
> to use it and have saved the configuration via the excellent utility.
>
>
I think the Config Save function in the K3 Utility saves the serial
number too, and only will load back into the same S/N. A way to save
only parameters that are not S/N dependent for transfer between radios
would indeed be nice.
73,
Fred K6DGW
Sparks NV
Washoe County DM09dn
On 2/12/2016
Gary Smith-2 wrote
> - Will I encounter any unexpected problems if I load my K3
> configuration to the K3s and start operating?
Probably...because Config Save will copy your K3 calibration constants into
the K3S. You would at least need to go through all calibration steps again.
I doubt the
Stewart,
I can't answer about any power problems with the K3 set to 0.2 watts.
But I do need to ask whether you are indicating 4 bars with the 5th bar
flickering on the ALC meter.
Failure to drive the audio sufficiently to achieve that indication on
the ALC meter is frequently the cause of
The K3 Utility reads the serial number and will only restore to the same radio.
73,
Ed W0YK
On Feb 12, 2016 14:04, Bill W4ZV wrote:
>
> Gary Smith-2 wrote
> > - Will I encounter any unexpected problems if I load my K3
> > configuration to the K3s and start operating?
>
Just wondering. I operate my K2 from a 7 amp hour battery that is recharged
by a solar panel. Is there a way to set up a system like that using the
KBT2 internal battery from Elecraft?
The solar panel I am using is just a 2.5 watt 167 MAh amorphous solar panel.
Thank you
Aaron Scott
K5ATG
It might be... but not until I DX All States first... ;)
__
Clay Autery, KG5LKV
MONTAC Enterprises
(318) 518-1389
On 2/12/2016 9:37 PM, Rose wrote:
>
> Clay, if tracking US counties is of interest to you, HRD doesn't.
>
> 73
>
> K0PP
>
Presently I use an external audio board for FSK. I run two versions of MMTTY
- one for the main receiver and one for the second receiver.
In MMTTY > Misc tab > Source for the main receiver I select Left and in the
second MMTTY I select Right.
Trying to setup the CODEC on the KIO3B. Is it
Hi Tony,
You may have to, I did, go into the Microphone -> properties -> advanced to
select a 2 channel microphone input.
Cheers, hope to hear you in the WPX.
73,
Fred KE7X
For all KE7X Elecraft books, see www.ke7x.com
From: Elecraft
Ah yes - a sow's ear into a silk purse can make the K3.
I have a woodworker nearby, built a perfect example of an RCA 44 -
except the internals are a RadioShack electret element. Runs it through
his EQ on the K3 and it sounds like the real deal. It is in use every
day and you cannot really
Thanks for all the responses. I find them very interesting. The only thing that
I'm missing is comments on the Elecraft MH2 Handset. I noticed that the CM500
has two stereo plugs and the mike inputs are mono. I have a Yaesu desk mike but
can't figure out the menu settings to use it's PTT
For the KX3, you can build an adaptor or use any old stereo to mono splitter.
That breaks out the tip and ring for you.
It is quite simple, but I explained it in a blog post regardless.
http://observer.wunderwood.org/2015/08/16/yamaha-cm500-headset-with-ptt-on-elecraft-kx3/
Us OT's can remember the times when microphone elements, like optics, were
largely hand-crafted. As such, the good ones tended to be expensive and
often fragile.
Nowadays, both optics and mic elements are manufactured using highly
automated processes that provide uniformly outstanding quality at
Bill,
If you are using the CW memory keys M1-M4 to send RTTY, add a "pipe"
character ( I ) at the end of the message. The K3 will ignore the
"pipe" character in CW mode, but will end the transmission immediately
when it encounters it in RTTY (FSK D) mode. The "pipe" character is the
upper
Fred,
That did it! I had not thought of going into the Mike> Properties > Advanced
to select 2 mikes.
Thanks for the tip. Audio cables gone.
N2TK, Tony
-Original Message-
From: Cady, Fred [mailto:fc...@montana.edu]
Sent: Friday, February 12, 2016 4:47 PM
To: 'N2TK, Tony'
I am in the process of setting up a second K3S that I just built and having
difficulties setting up RTTY using MMTTY
Using the USB Codec, I can key the rig, receive Audio in and copy RTTY, but
no Audio from the computer to the radio.
I have the correct speaker in the computer selected (USB Audio
It is no longer available...
Sold it!
73
Ozzie, w6icm
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
Yes, your MMTTY channel settings are fine. The USB Audio CODEC is stereo.
Not sure what you mean by the 4th paragraph below about the Microphone. If
you're talking about the Level adjustments in the Properties window for the
K3 USB Audio CODEC in the Windows Recording applet, the control is a
Here is something to check:
Right-click the speaker icon in the Task Bar and select Recording
devices. In the Sound window select the USB Audio Codec and click on
Properties. In the Properties window click on the Advanced tab and check
the Default Format. If it is set to 1 channel, ... change
Rich,
Thanks for your input. I had to go to the Mike input with the Codec and
change to 2 channel. That took care of the issue.
73,
N2TK, Tony
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of
Richard Ferch
Sent: Friday, February 12, 2016 4:54 PM
Irwin,
The K3S USB codec is no different than any other USB soundcard. Those do
have computer and OS dependencies that I cannot give specifics for. In
addition, how MMTTY interacts with your computer is another area that
must be looked at. You must tell MMTTY which soundcard to use. Then
Jim,
A Yaesu microphone will not work with the K3/K3S unless you construct an
adapter to change the microphone pinout. There are no menu settings to
accomplish that feat, you must build an adapter to route the AF and PTT
and their Return paths to the appropriate pins on the K3/K3S microphone
I have a MH2 as well as a CM500. The MH2 works very well. I use
it when my wife and I check into repeater nets so we both can
pick it up and transmit. I use it as a push-to-talk switch when
I'm using the CM500. (Some day i'll do the foot switch project.
Too much time operating, too little
I did respond but perhaps not clearly enough. Although I like my Koss SB45
headset, I use my MH2 daily and never had a complaint. TX EQ on the fph with
bias is set up for the mh2 and numerous compliments received.
The rph with bias is set up for the SB45 including the TX EQ.
Config: Fph with
FSK-D mode is perfect for casually dropping in on RTTY contests.
To receive RTTY directly on the VFO B display:
1. Tap DATA
2. Rotate VFO B to select FSK-D
3. Tap any switch to exit DATA setup
4. Hold TEXT DEC to turn on text decode
5. If you were using DISP to look at supply
Thanks to everyone. Simple Operator error. I forgot to set the mic to Lin
in for TX Data. That solved it.
Irwin KD3TB
On Friday, February 12, 2016, Bob McGraw K4TAX wrote:
> You do have the speaker level at about 50% on the computer. In the
> Windows 10 system I run, I
Rewire the mic plug - just remember it is - from then on - only to be
used on your K3. It is a 10 minute job - very simple.
Bill W2BLC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Or buy a microphone adaptor on EBay. You can find any type you need there.
Brian
KB1VBF
Sent from my iPad
> On Feb 12, 2016, at 7:47 PM, Bill wrote:
>
> Rewire the mic plug - just remember it is - from then on - only to be used on
> your K3. It is a 10 minute job - very
I have found that a brief press of the "SUB" key ends the extra 4 seconds of
carrier.
de Brian W3BW
Brian F. Wruble, C.F.A.
Sent from my iPad Air 2
> On Feb 12, 2016, at 5:43 PM, Bill Breeden wrote:
>
>
> Bill,
>
> If you are using the CW memory keys M1-M4 to send
OK, Trying to use KX3/PX3 with FSK D for the RTTY contest. I started
with MCU 2.38 DSP 1.37 then went back to 2.37/1.33.
20m decodes. 40m does not work (REV is ON and can not be changed) Both
versions. I don't remember ever seeing RTTY change like Side Band to
USB/LSB ??
I guess I can
Clay, if tracking US counties is of interest to you, HRD doesn't.
73
K0PP
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This
I'm not a frequent phone operator but thought I should at least have a mic so I
bought an MH2 when I ordered my K3 years ago. I used it a few times but decided
I didn't want to use a hand mic at the operating desk and put it away in a
drawer. (I take it when I deploy to Field Day since some ops
I would be interested to hear supported opinions as to which is better
and why between:
Win4K3Suite and Ham Radio Deluxe.
W4K3 is $50
HRD is now $100 for a new license and $50 a year for support (optional)
Go!
PS - I would have avoided this IF I could remember how to search the
archives...
44 matches
Mail list logo