in receive and then check transmit.
73,
Don W3FPR
On 7/26/2019 12:39 PM, James Doty wrote:
Oh, okay.
I honestly don't know what to look for though.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help
on the lower
bands.
In other words, you need to look for a problem different than a LSB/USB
problem.
73,
Don W3FPR
On 7/26/2019 12:20 PM, James Doty wrote:
It's a K2 with a 6 meter transverter.
I'll try your suggestion after work.
Thanks
.
If A K2, then try 17 meters USB.
73,
Don W3FPR
On 7/26/2019 11:19 AM, James Doty wrote:
It appears that USB is bad across the bands. I tried USB on 6, 10, 15,
and 20 meters.
__
Elecraft mailing list
Home: http://mailman.qth.net
.
Know what your software application is doing and you may have the answer
to your question.
73,
Don W3FPR
On 7/25/2019 2:41 PM, Kevin, N4TT wrote:
Hi Don:
I'm still checking things out but I think I have it all working
together. I calibrated the radio using WWV at 5, 10 and 15 MHz. I only
one of your FD "friends" did not tune the VFO from one band to
another without using the band buttons.
73,
Don W3FPR
On 7/25/2019 12:29 PM, James Doty wrote:
Hi all:
I didn't build my K2, I bought it second hand in excellent condition a
few years ago and really love it.
My K2 cam
for calibration and assessment purposes if used
in SSB mode. In CW mode, where the carrier frequency is important,
Alan's choice may be good.
73,
Don W3FPR
On 7/23/2019 2:31 PM, Kevin, N4TT wrote:
Maybe that's the basic question...
If I tune the radio to 7.035 to set a CW signal for a pitch
Mark,
While you may be correct about the TMP connectors, open the K3 and
rotate the TMP connectors a bit to wipe away any oxidation.
If it continues to fail after that, email supp...@elecraft.com for
further ideas on how to proceed. Tell them what you have attempted so far.
73,
Don W3FPR
200 watts in a quart can, while up to the legal limit
can be obtained in a gallon can of oil (Heathkit Cantenna style). Those
can be easily homebrewed and the amount of precision depends on the
resistors used and the care with construction.
73,
Don W3FPR
On 7/23/2019 6:43 AM, CUTTER DAVID via Elec
I also have a MFJ-264. I figured if I need a dummy load, go with one that will
handle the most watts I will ever need.
I don’t have much room, the MFJ-264 id s 1.5KW dry dummy load for 1-650MHz. A
little smaller than a carton of cigs.
Haven’t used it yet.
Don, KE0PVQ
Sent from Mail<ht
G RPT for the repeat interval you want to use.
See the CW/DATA Message Record/Play section of the KX3 manual.
73,
Don W3FPR
On 7/22/2019 12:39 PM, Mike Parkes wrote:
I am searching for what software exists that will allow the KX3, while in
data modes (rtty for example), to send a group of CQ's... and
Petr,
It does change to slow AGC, but any custom settings remain in place.
73,
Don W3FPR
On 7/22/2019 11:39 AM, Petr, OK1RP/M0SIS wrote:
Roger,
you would like to say that when I will enable CW decoder the AGC system
ignore all custom's settings and going to use default Slow AGC template
steps - it can
work as long as you do not have RIT or XIT turned on.
Switch the rocker back to VFO A (or B) to finish the fine tuning.
73,
Don W3FPR
On 7/21/2019 11:47 AM, Kevin, N4TT wrote:
A scenario from yesterday's contest.
I have the P3 set up to view about 3 or more KHz of spectrum. I
Kev and all,
No vote on that dynamic VFO tuning for me. It would only be suitable
for me if I could turn it off.
I have used a couple transceivers that had that type of tuning and it
drove me nuts.
73,
Don W3FPR
On 7/20/2019 1:38 PM, Kevin, N4TT wrote:
Consider one of the settings
Raj,
Don't overlook the possibility that the RJ-45 jack could be damaged.
If you have ever accidently plugged the USB cable into that jack - it
almost fits, but will damage the RJ-45 jack.
73,
Don W3FPR
On 7/19/2019 2:32 PM, Rajiv Dewan wrote:
Hello all, especially Don,
The last tip
the USB cable back in - which COM port is assigned? Put that
COM port number into K3 Utility and try to connect.
73,
Don W3FPR
On 7/18/2019 10:03 AM, Rajiv Dewan wrote:
Hello,
I have KIO3B (USB interface) in my K3. It was working well. Single
USB for audio, and CAT.
Suddenly, now
Thanks Dick.I'll check that out.DonSent via my Mobile
Original message From: d...@elecraft.com Date: 7/17/19 10:37
AM (GMT-08:00) To: 'Don Sayler' , elecraft@mailman.qth.net
Subject: RE: [Elecraft] Remote K3s clock setting The K3 Utility adjusts date &
time with S
I've looked through the Programmer's Reference guide for info on setting the
K3S clock remotely.I have found information for the clocks in the KX2 & KX3.
There doesn't appear to be a command for setting the clock in the K3S. Did I
miss something? There must be a way, since the Elecraft Utility
ansverters from the output of your band decoder.
73,
Don W3FPR
On 7/17/2019 8:55 AM, Rus Healy wrote:
Good morning. I have a K3 with the internal K144XV 2-meter transverter. I
want to use it not just for 2 meters, but also as an IF for 903, 1296,
2304, 3456, 5760, and 10 GHz. I have built a ba
Peter,
See the article on my webpage www.w3fpr.com. Scroll down to the last
entry on the left column and click to bring up the document.
73,
Don W3FPR
On 7/16/2019 6:46 PM, Peter Dougherty wrote:
I should have mentioned, this is on a K3s. What radio settings are involved? Is
it mic gain
Paul,
What I said refers to the KX3 only. For the KX2, there is only a
single TRRS jack instead of the KX3 ACC2 jack which is TRS. So the
wiring for the KX2 is different than what I specified.
73,
Don W3FPR
fine.
Set all the DIP switches to OFF - those switches only respond to the
Power On the XV from the transverter. That signal is only available
from the K2 and K2, it is not available from the KX3.
73,
Don W3FPR
On 7/8/2019 9:08 PM, Paul Gacek via Elecraft wrote:
I would like to connect
Lloyd,
Pull the key plug out, then see if it stops. If so, check the key and
the plug. The plug must be stereo and have the key connected only to
the tip and the shell (no connection to the ring).
73,
Don W3FPR
On 7/8/2019 11:27 AM, LL wrote:
I just set my new-to-me K1 up in the field. I
be diminishing soon.
73,
Don W3FPR
On 7/7/2019 2:27 PM, Ryan wrote:
My K2 was having this same issue with the PLL test. I replaced the Q19 J310
with one on hand and it fixed it. Should I replace all the J310 in my kit,
and option kits, or are the sub-par J310 only a problem in the PLL circuit
Steve,
DVR or CW and digital modes?
If CW or digital, use K3 Utility to edit the messages with the keyboard.
73,
Don W3FPR
On 7/6/2019 1:14 PM, KI4EZL wrote:
Hi, K2 REC button will not let me change messages. MSG button works fine.
Radio seems fine. Just cannot get in and change any
them one at a time.
Before doing anything, check with the Elecraft sales office to be
certain both the p/n E600015 and the backlight kit for an unbuilt K1 are
available.
73,
Don W3FPR
On 7/6/2019 4:34 PM, LL wrote:
The backlight mod on the Elecraft site says that it's for unbuilt kits. Can
.
Reflow the soldering for all the components in the VFO area.
73,
Don W3FPR
On 7/5/2019 7:01 PM, Christopher Bowne wrote:
My 40 and 20 meter K1 has developed intermittent frequency instability and
sometimes complete loss of ability to tune (frequency display jumps and stays
on 68.0 nominal on 40
Note carefully that Wunder specified a "SPLITTER" and that is different
than an 'adapter'.
The more common mono to stereo adapter will NOT cure the condition.
73,
Don W3FPR
On 7/5/2019 3:28 PM, Walter Underwood wrote:
The mic plug is shorting the “mic button” (PTT) contact. S
).
If the power rating of the bandpass filter is marginal with respect to
the rig power, then I would observe that caution. Refer to the bandpass
filter specs.
73,
Don W3FPR
On 7/5/2019 10:57 AM, Rich wrote:
To minimize emails direct replies would be nice. I searched the web and
could not find
at a time to see
which external device is causing the problem.
73,
Don W3FPR
On 7/4/2019 9:34 PM, John and Rita Freitag via Elecraft wrote:
I am trying to run down a CW transmit problem on my K3s. Anytime I change the
mode from LSB or USB on any band to CW it starts to send a “dit” without
Lloyd,
Take a look at the crystals on the 2 band board. The crystal for 40m
will be 15MHz, the one for 30m will be either 18.0 or 18.1 depending on
whether you have the 150kHz or 80kHz VFO tuning range. The crystal for
20m is 22MHz.
73,
Don W3FPR
On 7/3/2019 6:47 PM, LL wrote:
My new 30
Jim,
You might want to check the PLL Reference Oscillator Range on that K2 -
sometimes called the "R30 voltage".
Don W3FPR
On 7/3/2019 5:24 PM, Jim KO5V wrote:
Don,
Setting each VFO to a frequency within the 15M band cured the "VFO B-A" pop. I checked
the other
back into the 15 meter band limits.
73,
Don W3FPR
On 7/3/2019 3:57 PM, Jim KO5V wrote:
Hi again,
I did as Don suggested, and checked the values of all of the capacitors around
U1, and all of the band-switching relays. I also re-flowed all of their solder
joints. With the bottom panels, top
Andy,
That appears to be a TS-590/HDSDR problem and not a KPA500 problem.
You can likely get more support from th TS-590 and HDSDR forums than
from us on the Elecraft reflector.
73,
Don W3FPR
On 7/2/2019 10:19 PM, Andy Durbin wrote:
"In my case HDSDR sound output had spontaneously ch
Lyle,
Does that include the KDSP2 Firmware IC code? Or is it only the code in
your DSP-x module?
73,
Don W3FPR
On 7/1/2019 7:21 PM, Lyle Johnson wrote:
FWIW the DSP source code for the KDSP2 was and has always has been open
source. Until the Elecraft web site update in the last several
...@elecraft.com.
73,
Don W3FPR
On 7/1/2019 9:05 PM, Fred wrote:
Hi,
I have a K3, P3, KPA500, KAT500 and a SignaLink for sound. Sometimes when
I transmit on FT8 running full power on the KPA500, the KPA500 will click
on/off. The power doesn't turn on/off, it seems like a relay inside
itten code would be
a very costly venture for Elecraft.
73,
Don W3FPR
On 7/1/2019 5:13 PM, Bill Frantz wrote:
I must strongly disagree with Bob. Before I retired, most of my career
was spent writing code. This code became the property of my employer,
and when they went bankrupt, I could not a
to switch, remove it and test from the K2 buttons.
73,
Don W3FPR
On 7/1/2019 1:04 PM, Jim KO5V wrote:
Hi Don,
OK, the rig is S/N 7225. No KDSP2 is installed. I'm using an external CLRdsp
box and speaker. The rig has been working very well; I've received many good
signal reports. The DSP , AUX I/O
display, the cable between K3 Line Out and soundcard line in (mic) is
working.
If you still have problems, contact supp...@elecraft.com for further
analysis.
73,
Don W3FPR
On 6/30/2019 11:43 PM, Skip Cameron wrote:
While using my K3 in data A mode with wsjt-x software on 6M, TX stopped,
and other
e as shown in the DC
voltage tables.
73,
Don W3FPR
On 6/30/2019 4:55 PM, Jim KO5V wrote:
Good Afternoon,
Today I noticed a "pop" on the audio of my K2 when I changed in and out 15M, so
I checked the switching on all bands:
When changing from 15M to 12M or 17M it is fairly loud. Chan
offsets for up to 6 bands.
You only need to change the board and set the "b1" and "b2" menu
parameters to match the bands of the boards in use.
73,
Don W3FPR
On 7/1/2019 9:25 AM, LL wrote:
I'm acquiring a K1 with ATU, 30 and 40. Really would love to have 20 and 80.
If n
mobile - my eyes and attention need to be on
the road and not some device in the vehicle.
73,
Don W3FPR
On 7/1/2019 7:09 AM, Sergey Zimin wrote:
I meant the 5-watt version of the k4 with a panadapter in a single package
the size of which is like kx3...
пн, 1 июл. 2019 г., 13:16 Nr4c
adapter, that was likely damaged too.
73,
Don W3FPR
On 7/1/2019 6:30 AM, Juha - oh6os wrote:
Hello,
Yes, all cables was connected during the first lightning bolt nearby.
Now K2/10W is ok! All work fine, luckily.
But with KPA100:
1) Metering (K2 LED paragraph) do not show anything.
2) I get 10W
That gentleman is mistaken unless something happened while I was not
watching, the KX3 does up to 15 watts.
73,
Don W3FPR
On 6/29/2019 4:04 PM, JP Douglas wrote:
Hi all!
While having a QSO yesterday from my mobile to a QRP station on 20 meters, the
gentleman I was chatting with mentioned
d for data (4 bars solid, 5th
flashing) or voice modes (5 to 7 bars) and all will be well.
73,
Don W3FPR
On 6/29/2019 1:35 PM, Greg Troxel wrote:
I have always been a bit unclear on what the Elecraft ALC/power was
really doing.
You mention low power then then hunting, and the notion of a set p
.
For the computer connection, just use standard stereo audio cables - no
need to match impedance - just set the audio level correctly.
For amplified speakers, I recommend West Mountain Radio COMspkr mainly
because they are shielded and do not howl with the transmit RF.
73,
Don W3FPR
On 6/29
audio with the KX3 MIC Gain set
near its mid-point, then you will have to add an attenuator.
One note on the KX3 - if you drive the audio with too large a signal,
the mic amplifier will shut down and the MIC GAIN will not work anywhere
in its range.
73,
Don W3FPR
On 6/28/2019 3:01 PM, Richard
. Then leave it that way and adjust the
desired power with the power knob. Doing otherwise will result in low
power at the start and power hunting as the transmission goes on.
73,
Don W3FPR
On 6/28/2019 2:38 PM, Brian Denley wrote:
I have always thought that ALC is not appropriate for power
Brian,
Use the postal system. There are no "brokerage fees" charged by the
postal system. UPS and FedEX do charge "brokerage fees" Customs is a
different matter - usually properly marked customs forms will go through
with no problem.
73,
Don W3FPR
On 6/28/2019 11:
ave had my K3 when I did "fumble fingers" to interrupt
the total download.
73,
Don W3FPR
On 6/25/2019 7:51 PM, Bernie and Cheryl wrote:
I got my K3s (#10323) back in October, 2015, and got my KPA 500 (#2664)
a few months later (I have the full K line including the KAT 500).
When I built them,
one. The Icom
forums would be your best resource for the base way to add one.
73,
Don W3FPR
On 6/25/2019 5:59 PM, Jim Dodds wrote:
Has anyone added a P3 Panadapter to an ICOM CI-9100 transceiver? If so, are
there any reasonably detailed instruction available to mod up the IC-9100
cable for tightness.
The K3 power cable should run direct from the power supply. Rigrunner
and other DC power distribution boxes can be reason for excessive
voltage drop.
You can increase the power supply voltage up to above 14 volts to help -
do not exceed 15 volts.
73,
Don W3FPR
On 6/24/2019
If the red TX LED comes on, that is not the problem.
73,
Don W3FPR
On 6/24/2019 11:02 AM, David Box wrote:
Have you tried with VOX ON?
K5MWR
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http
focus on the Line In or the soundcard output for the problem source.
73,
Don W3FPR
On 6/24/2019 9:29 AM, Paula Uscian wrote:
I suspect I may have an issue with the Line In port of my K3, as my ability to
TX in any digital mode has gone away.
Setup:
1. Using a Tascam US-122 MKII outboard sound
Paula,
Have you verified that you have audio out of the soundcard?
Plug headphones or amplifier computer speakers into the soundcard line
out jack and do a "transmit" from the software. Do you hear audio
tones? If not, you have a soundcard problem.
73,
Don W3FPR
On 6/24/20
the formula yourself, you can do that, but
represent the RMS voltage as V time sqrt 2 rather then the approximation
of 1.414 (or 0.707) which is normally shown. The sqrt will cancel out
when it is squared.
73,
Don W3FPR
On 6/20/2019 10:50 AM, Ken Roberson via Elecraft wrote:
Don , That may
squared then divided by 400. Easy to do quickly with a
handy calculator.
73,
Don W3FPR
On 6/20/2019 9:38 AM, John Oppenheimer wrote:
Using DL1 with Oscilloscope to measure KX3 SSB RMS power:
https://www.kn5l.net/ssbpower/
Question, is this technique correct
support calls
saying "I have lost me K2 sidetone".
Great that you got the microphone situation sorted out.
Yes, K2FCTR_K2 is the internal frequency counter probe parts.
It is good to hear that you knew about the need for the special K2 to
computer serial port cable.
73,
Don W3FPR
under my belt). So when you indicated high base voltage on the
PA transistors I knew where it was coming from.
The Q13 voltages you measured are within reason.
So yes, install the new Q7 and Q8 transistors and you should be good.
73,
Don W3FPR
On 6/18/2019 7:32 PM, Jimithy66 wrote:
Other
shown in the KIO2 manual to
have PC to K2 communications. Do NOT plug a standard serial port into
the K2 AUX IO connector - it contains internal K2 signal lines as well
as 3 RS-232 signals. Using a standard serial cable can cause damage to
the K2 and possibly the serial port.
73,
Don W3FPR
jack to see if you can hear audio when the software application transmits.
73,
Don W3FPR
On 6/17/2019 2:39 PM, k...@juno.com wrote:
I've been using my K3 almost exclusively on WSJT-X FT8 since the mode
came into being. Things worked fine until a couple days ago when I no
longer see any power
Conrad,
Do check and adjust the Windows soundcard controls to mid-range. When
set to extremes, it can cause clipping and distortion.
With the K3S, the internal soundcard will identify as USB AUDIO CODEC.
73,
Don W3FPR
On 6/17/2019 11:21 AM, Conrad PA5Y wrote:
Don of course
Bill,
Congratulations, it sounds like you have achieved success.
Once set the K2 alignment usually remains stable for a long time. If it
ain't broke, don't fix it!
Don W3FPR
On 6/17/2019 10:36 AM, Bill Coleman wrote:
Well, I think I finally got it sorted.
I replaced D1 and D2 on my KAT100
ranseivers. The lower 4 bars
of the "ALC" meter are there as an aid for setting the audio levels.
Set the desired power output with the POWER knob - do NOT vary the audio
level.
73,
Don W3FPR
On 6/17/2019 9:38 AM, Conrad PA5Y wrote:
Historically there were all kinds of low level artefacts
o not have the proper crimping tool, soldering is OK, but
support the wire for about 2 inches away from the soldered terminal so
there is no chance that it can flex.
73,
Don W3FPR
On 6/16/2019 7:22 PM, Kidder, George wrote:
Interesting data, Don. I wonder if there is any information about
adequate for the task.
73,
Don W3FPR
On 6/16/2019 6:04 PM, Bob McGraw K4TAX wrote:
Also if you use your computer for other "sound" activities, any change
made from that activity may or will change other things. Just
understand how things works and expect to quickly be ab
It may be better said that a Noise Blanker responds best to impulses
with a fast rise time like ignition noise from a gasoline engine. It
does not have to be repetitive (but often is).
73,
Don W3FPR
On 6/14/2019 2:05 PM, Wes wrote:
I have one little nit to pick with this. In a properly
Or any other multiband antennas in a multi-transmitter situation.
73,
Don W3FPR
On 6/14/2019 1:36 PM, Bob McGraw K4TAX wrote:
Neither should G5RV antennas.
Bob, K4TAX
Sent from my iPhone
On Jun 14, 2019, at 10:44 AM, donov...@starpower.net wrote:
oops... I meant to say:
Inverted V
e NO ALC
point).
Set the power desired with the POWER knob.
See the related article on my website www.w3fpr.com.
73,
Don W3FPR
On 6/14/2019 11:24 AM, Charles wrote:
Hi Don - I *did* say that unclearly. What I meant was that I tried
operating 5W with the Win10 volume mixer slider at 50% and 100%
much
input, the KX2/KX3 will shut down the audio amplifier. It may be that
you are driving it with too high an audio level. Back down on the
computer generated audio and see if things are restored to normal.
73,
Don W3FPR
On 6/14/2019 9:23 AM, MaverickNH wrote:
I'll add that, with Win10
the newer kits.
73,
Don W3FPR
On 6/13/2019 3:33 PM, Jimithy66 wrote:
I finished building a basic kit with no options and the power output will
not rise above 2 watts and current (2A) is too high for that power.
Hi Cur flashes briefly before power output settles at 2 watts.
Voltage checks found the PA
Richard,
I suggest you contact supp...@elecraft.com for that information and
possible resolution.
73,
Don W3FPR
On 6/13/2019 3:07 AM, Richard Corfield wrote:
Serial number is 8383, if that helps place the manufacturing date and
therefore whether it's part of a batch with a known issue
may help.
73,
Don W3FPR
On 6/12/2019 8:23 PM, Bill Coleman wrote:
Yeah, this is looking more like a calibration problem.
I’m listening to W1AW code practice on 14.0475. As I cycle through the filters
the S-units are roughly the same through OP1, 0.4 and 0.16. But on the 1.0
bandwidth
tightness and your crimp connections.
Run the transceiver direct from a power supply using ring terminals
instead of routing through a power distribution accessory.
73,
Don W3FPR
On 6/12/2019 6:29 PM, Bob McGraw K4TAX wrote:
Regarding "heavy gauge wire", I suggest one measure the voltage d
my website www.w3fpr.com. Scroll to
the last link in the left column and click to open the link.
73,
Don W3FPR
On 6/11/2019 8:42 PM, Rick WA6NHC wrote:
On 6/11/2019 4:19 PM, Jim Brown wrote:
Fox and Hound certainly "requires" it.
No, it does NOT. The frequency shifting can all be done
Bill for receive, you only need the jumpers at J9 and J10 - it is quick
and easy to do with bent wires if you do not find the rework eliminators
is short order.
Those jumper wires will not complete the transmit path - only receive.
73,
Don W3FPR
On 6/11/2019 5:03 PM, Bill Coleman wrote:
I
generator (if not, use band noise, but make sure there are on
signals on the band segement used).
If the CW filters work OK with the KSB2 removed, the troubleshooting
should start with the switching diodes on the KSB2 option.
73,
Don W3FPR
On 6/11/2019 2:53 PM, Bill Coleman wrote:
OK, I have a K2
is with LP-Bridge, which buffers K2 information to
take the load off the K3 serial communication.
Yes, WSJT-X wants to have total control of the radio.
73,
Don W3FPR
On 6/11/2019 2:47 PM, Wes wrote:
Maybe the collective wisdom of this group has an answer not to be found
elsewhere.
Currently, I
. If the
microphone is out of warranty, then order a new one.
73,
Don W3FPR
On 6/11/2019 2:45 PM, Barry LaZar wrote:
Don,
Interesting. My KX3 is s/n 324, an oldie. Do you know who is
making the new mics? I, too, may need that info for future reference.
73,
Barry
K3NDM
On Tue, Jun 11, 2019, 2:40
Barry,
I do not believe that is true anymore (except for the ProSet-K2).
The original MH2 microphone was Heil, but that was changed a very long
time ago.
Since you just bought the MH3, your best recourse is to contact Elecraft
about a replacement.
73,
Don W3FPR
On 6/11/2019 2:15 PM, Barry
Jim and all,
That is not quite correct. KEY1 is for the 3.5mm jack on the side panel
while KEY2 is for the paddle connection on the front (the KXPD3). Check
the information in the menu listing description in the manual.
73,
Don W3FPR
On 6/10/2019 10:32 PM, Jim Rhodes wrote:
Actually you
www.w3fpr.com and scroll down
on the home page to near the bottom. You will find links to both
version 5.17 and version 16.
73,
Don W3FPR
On 6/10/2019 7:52 PM, wes Bolin wrote:
I have a very nice K2 that I bought as previously owned. It works fine on
SSB on
20 Meters. The audio from
as P1, RF Board J7 and Control Board P2. Also reflow Control
Board U6 pins 8 and 16.
73,
Don W3FPR
On 6/10/2019 9:09 AM, Steve Kavanagh via Elecraft wrote:
One of my K2's has developed a problem where it is (somewhat intermittently)
unresponsive to turning the tuning knob. Turning the knob
.
73,
Don W3FPR
On 6/9/2019 12:11 PM, inventor61 . wrote:
My K2 #771 has a KIO2 that has no serial data output.
This appears to be due to a problem ... in the other direction.
I can see my inbound ASCII commands (e.g., FA;) at pin 6 of U1 on the KIO2
board.
However, the MAX1406 shows only rail
Rich,
There is no need to bypass the P3, just connect the SDRPlay to the P3 IF
output.
The P3 IF output is a replication of the K3S IF output.
73,
Don W3FPR
On 6/9/2019 7:04 AM, Richard Thorne wrote:
I'd like to try Win4K3Suite with an SDRplay receiver. I've been looking
for a block
rwork from Elecraft available.
Thanks,
--
Don Minkoff
NK6A
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hoste
Evert,
No, it decodes by band and not by frequency segments.
73,
Don W3FPR
On 6/6/2019 11:32 AM, Evert Bakker wrote:
A Q abt the KRC2:
Is it possible two switch to two different antennes within one band but
based on frequency span
David,
You are apparently looking for the Elecraft KRC2. It is on the website
- enter KRC2 in the website search box to find it.
73,
Don W3FPR
On 6/6/2019 10:52 AM, David F. Reed wrote:
In planning my next station, I have not found one item I would like to
add...
I wish to automatically
to
during Field (Beta) testing, and the comments during Field Test will no
longer be relevant.
It is that same way for the Beta Test period of any product.
73,
Don W3FPR
On Thu, 6 Jun 2019 at 04:54, Leroy Buller wrote:
Are there any K4 Beta Testers out there yet? If so, can we get
ports should go away - then plug it back in and see which COM port is
assigned. Put that COM port into K3 Utility and TEST COMMUNICATIONS.
Windows sometimes changes the COM port assigned to USB to serial
adapters - thanks Microsoft!
73,
Don W3FPR
On 6/5/2019 5:37 PM, Mike March wrote:
My
to a PF button.
73,
Don W3FPR
On 6/4/2019 7:52 PM, Fred Jensen wrote:
That doesn't work Wes, the problem is simpler than that. However, Don
has confirmed the behavior, and now it's time for me to be a "Real Ham"
and do something here in NE Sparks NV [instead of on the list] to fix
&q
ou can see which is which without referring
to the frequency.
73,
Don W3FPR
On 6/4/2019 3:02 PM, Fred Jensen wrote:
This began as a simple question, I can't understand why it is so hard to
explain: K3 frequency memories hold frequency, mode, and DSP BW for
both VFO A and VFO B. I used the K3
will need that connection - most applications will work without it.
73,
Don W3FPR
On 6/4/2019 3:26 PM, Harry Yingst via Elecraft wrote:
To Clarify this information
-
The color codes are from the wires on the FTDI USB Cable
(USB-RS232-WE-1800-BT-0.0)
-
The only wires that will be connected
to the maximum which will cause
additional damage if that condition exists for more than a very short time.
Build the PC to K2 cable shown in the KIO2 and KPA100 manuals and plug
it into that adapter or most any other FTDI USB to Serial adpater.
73,
Don W3FPR
On 6/4/2019 2:10 PM, Harry Yingst via
,
Don W3FPR
On 6/3/2019 4:38 PM, Dave New, N8SBE wrote:
Shouldn't need to tie up a PF for this feature. The K3 should be able
to remember the setting on a per jack basis.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman
the S-meter indication increase.
If it does not, you have a display problem - reflow the soldering on the
LED bargraph and Front Panel RP2, then check again.
73,
Don W3FPR
On 5/31/2019 9:42 PM, Mike Short wrote:
I recently bought a used K2/10 and the S-Meter does not work. I am looking
.
You will also need to download the KX3 Utility from the Elecraft website
and install it on your computer.
73,
Don W3FPR
On 6/1/2019 4:43 PM, Robie Elms wrote:
All,
I have acquired a used KX3 (serial number between 4000 and 5000, uC
firmware 0.150, dsp firmware 01.21) and I am checking it out
- and should never be used with the KSB2 option or the
KPA100 option installed (or any external amplifier).
When counting toriod turns, count the number of times the wire passes
through the center of the core.
73,
Don W3FPR
On 6/1/2019 2:48 PM, Jimithy66 wrote:
Am in final testing of a K2 Ver.A
#10 or #8 wire will need the 45 amp contact blades.
However, if the purpose is to minimize voltage drop, there is no need to
use the larger connector - construct the power pole with #12 wire about
3 inches long. Then splice onto that with #10 or #8 wire for the rest
of the run to your power
Even being left handed, I have no problem using my right hand on the
knobs. That leaves my left hand free to do other things requiring a
greater degree of hand/finger coordination.
I like it the way it is.
73,
Don W3FPR
On 5/31/2019 11:42 AM, George Thornton wrote:
If Elecraft reflects
on the tip of the housing, they are
not genuine.
73,
Don W3FPR
On 5/31/2019 11:11 AM, Lee Trout wrote:
I am looking to replace the powerpole connector on my K3. Am I correct
that these 30 amp ones on fleabay are the ones I need? Thanks for any
801 - 900 of 15664 matches
Mail list logo
