t was working perfectly in the week and I am thinking a connector may
have worked lose in transit. Accessing the Field Day site involved a
drive along bumpy farm tracks and a steep grassy incline which my 4x4
SUV coped with OK but apparently not the K3!!
Chris
That's it!! I had forgotten about that menu setting. Works properly now.
I can detect some low level crosstalk but I suspect less than the
FT1kMP. Will check with some big sigs in WPX.
Thanks for all the responses.
Chris G3SJJ
Guy Olinger K2AV wrote:
> Make sure you have that you do
. Neither operator should hear the other rx. This works perfectly
with the FT1kMP but so far I can't get it to work with the K3. Any
suggestions?
Chris G3SJJ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/ele
e but anything in
particular!
The 2nd Rx sounds great.
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/ma
Sorted. I had Disabled Router Queries on the mHam Router but it still
didn't like it so I changed over a USB / Serial Interface and that
worked. My bad. Sorry.
Chris G3SJJ
Dick Dievendorff wrote:
When you power up the rig, if the red Tx Led is flashing and you see "MCU
LD" in
Pressed the wrong button or something! Tx LED flashing but download has
hung. I have switched off the PSU, switched on again and held the Power
button down for 30 seconds which I think I had to do once before, but no
success. Help please!
Chris G3SJJ
G3SJJ (GU4CHY/P - IARU Region 1 SSB Field Day 6/7 September)
Alan Bloom wrote:
It should work fine as long as the receiver is on a lower band than the
transmitter because the ATU is low-pass in nature.
Al N1AL
On Thu, 2008-08-07 at 09:59, Chris G3SJJ wrote:
Whilst I am waiting for shipping
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qt
Does anyone have any figures on efficiency of KAT3 for load impedances
of 20 and 200 ohms? (reactance not known at this stage.)
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list
Auto character spacing for K3. Yes, please.
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo
Grateful thanks to Mal G4KFT who reminded me that I should set mHam
Keyer to No Radio.
K3 working, latest downloads installed, sounding really, really good. Phew!!
73 Chris G3SJJ
G3SJJ wrote:
Altered the subject to Download! Well, one step forward, two steps back!
After several emails
t has mentioned below. I am using the mHam Keyer as my radio to
computer interface. If I could get the K3 to work I could go back to RS232!!
Chris G3SJJ
Stewart Baker wrote:
No need to be embarrassed Chris, the same thing happened to me.
I found that things got screwed up with the microkeyer r
radio
A most embarassed Chris G3SJJ !!
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help:
y does a DL, SP, IZ, 9A or whatever transmit?!!
Thanks. Chris G3SJJ
Eric Scace K3NA wrote:
Some reported hiccups with the radios should be put into perspective:
1. We ran 8 radios x 24 hours x 16+ days of operating: over 3,000
hours on the air in total... plus additional hours for some units
fine.
I have also tried unplugging different cables one by one but cannot come
to any specific conclusion.
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. C
x27;t have the same voltage drop and they work well. The K3
drives them fine also.
(A photo may appear in the next issue of RSGB Radcom since they asked me
for a photo of the K3 setup!)
Chris G3SJJ
Dick Dievendorff wrote:
I've purchased but not yet installed one of these. I have also
Been there, noticed it, believed in Elecraft mojo, adjusted the position
slightly, continued, made 1500 Qs since. No prob.
One man's challenge, another man's major disaster!!
Chris G3SJJ
Ron D'Eau Claire wrote:
Yes, I spoke with Wayne about it recently after other build
Wow, that did it Don. Thanks.
Chris G3SJJ
Don Wilhelm wrote:
Chris,
You might try setting the data rate higher. For some strange reason
the USB to serial adapters have more trouble working with slow data
rates.
73,
Don W3FPR
G3SJJ wrote:
I am unable to get my K3 talking to either my
avoided these. In
Device Manager I can see "Proloific USB-to-Serial Comm Port and it
indicates everything is working OK.
Not sure where to go from here. Any ideas?
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
er so simple. If he sends your callsign you transmit, if he doesn't
send your callsign you don't transmit! What bit of that don't they
understand?!
Chris G3SJJ
Vic K2VCO wrote:
Lee Buller wrote:
Uh...when I was working Ducie, the DUAL-WATCH feature of my 756PROII
came
My 160m QSO is in the log, VP6DX-K3 to G3SJJ-K3. Nice one.
Currently listening to them on 40m at s7 long path, s3 on short path.
1454z. Pair phased gp.
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber
My K3 works very well with the current version (3.8.0) Chris. The K2 I
had in 2006 worked well also with whatever the version was then. I
wonder what will be changed?
Chris G3SJJ
Chris Gibson wrote:
For information: the next version 3.9 of Logger32 will include support for
Elecraft K2/K3
I confirm the TopTen Band Decoder works fine with my K3, Andy.
Chris G3SJJ
Andrew Faber wrote:
Chris,
Good luck with it. I have the TT Decoder powered by an independent 12
volt source. It has internal pull-up resistors, so there appears to
be no connection needed other than the ones I
Oh thanks for that Andy. I'll get it wired up in the morning with
confidence then! I know that Dave N3RD (of Top Ten) and Sig N3RS are
eagerly awaiting their K3s and will also be interested.
73 Chris G3SJJ
Andrew Faber wrote:
Chris,
I have my K3 hooked up to a Top Ten Yaesu decoder
000
allows for that.
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://
data out socket f for my TT Decoder and pick
up +12v from there, also amp relay switching. Would have been nice on
the K3!
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber
bandwidth
coinciding to the
to 2.7KHz filter? In fact, I would be happy to have a max b/w of 2.3
since I am used to 2KHz Inrad in my FT1kMP anyway.
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to
This is real radio, real contesting with a real contester's K3.
Thanks Aptos !! Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
For some reason I thought a 15 pin connector would be included, had a
recollection of past discussions but looks like I was wrong.
RS232 works well with Logger32 and N1MM, straight in, no parameter
changes required.
Chris G3SJJ
___
Elecraft mailing
the those who think we should not complain. For me the Elecraft
experience has been tarnished by both of those aspects, and it will take
some time to recover. For now though I can savour the sweet K3!
Chris G3SJJ
___
Elecraft mailing list
Post to
K3 Serial Number 278, ordered 14 May, arrived safely in Nottingham at
0900 this morning. Assembly in progress.
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr
I think so. So Don's 275 plus 25 might be good. Yes, 14th May at 1800z
was the originally announced cut off.
Sorry for all the posts, I guess A) the excitement of my very impending
K3 and B) the culmination of 3 months of watching serial numbers!
Chris G3SJJ
Mike B wrote:
If I under
or when the sub rx
actually happens!!
Could just get my K3 in time for CQWW160 CW net weekend, now that really
would be nice!
Chris G3SJJ
Don Rasmussen wrote:
My thought exactly - and off to the wiki to make a
quick change on the estimate before anyone notices.
;-)
Current swag, 275 deposit
Right, that blows my theory of 250 for the first prodn run! Beginning to
look like 300 then.
Chris G3SJJ
Geoffrey Downs wrote:
K3/100 kit S/N 000266 delivered here 1333 UTC today 21 January having left
Aptos 18 January. It travelled at an average speed of about 99 mph. Ordered 11
May 2007
other than a logging
program. I use Logger32 for general use and N1MM for contests, both have
the usual radio interface and Cluster access via Telnet. I am obviously
missing something but not sure what!
Chris G3SJJ
Peter Bacon wrote:
I successfully use TRX-Manager to control my K3, and feed
UPS calls in a few days
time. Yippee
Chris G3SJJ
DOUGLAS ZWIEBEL wrote:
Eric, Wayne:
I am requesting that you (A) release the size of "production run 1"
and also please tell us (B) how many K3s are still pending "without
deposit" from run #1.
I know that initially you
e to watch is knock the power knob back on the MP to roughly
the area I know that gives me a reasonable ampount of power out of the
amp, say 30-50 watts. I would have thought this technique would have
been OK with the K3.
Chris G3SJJ
Well, when you wish to go from 100w, down to 3w, in order
That sounds similar K2 bandpass filter switching relay, noisier that I
would have thought but acceptable. The relays in my Dunestar 600 are
audible but quieter than the K2.
Chris G3SJJ
Jonathon
One thing I've noticed is the relay noise (physical, not RF) when switching
between bands.
Sunday! so it is gathering momentum. Have fun.
Chris G3SJJ
Bob Evans wrote:
Chris,
You may want to recalibrate your shipping estimate by a few days. I have
just received notice that my K3/100 kit (100% prepaid- 50% deposit with
order and the second 50% paid in August upon original shipping
y original thoughts about 1st prodn run volume
seems to be tracking well.
Exciting times Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub e
G3SJJ
DOUGLAS ZWIEBEL wrote:
Chris, et al:
Before you get too locked into a plan, remember that the orders being
shipped from Prod Run #1 (so far) are for those "with deposits." One
could reasonably infer that after those "with" deposits are shipped,
they will circle back t
am
trying to do some realistic planning and tracking serial numbers is helpful.
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub e
We are all a bit confused about your name, Oliver
You know, this thread is all well and good, but no-one has yet answered the
original question :)
Which is:
I might have missed this in the manual, but when I change the NB IF width
value, I can get to a point where the NB flashes - what do
le to setup the
keyer functions from a pc.
I just seems logical that the Keyer in the K3 maybe could do that,
either that or incorporate the various facilities that Winkey has. I
couldn't see the point in going backwards to older keyer designs.
73 Chris G3SJJ
Brendan Minish wrote:
On
Wow Brendan, that is a bit old hat! Most logging programs now allow for
K1EL Winkey setup so that seems the way to go.
73 Chris G3SJJ
Brendan Minish wrote:
What would be wonderful is if elecraft could licence and implement the
logikey Comos4 firmware in full.
I have been using the logikey
and auto character spacing! Actually it needs K1EL embedding!! Now that
would be nice!
73 Chris G3SJJ
Karsten Koch wrote:
Hi Tom,
wouldn't it be nice to have the BEST keyer available TOGETHER with the
BEST transceiver ... ANYWHERE?
For the time being I'll be happy with my K2.
Dunno, but it looks awful!
Chris G3SJJ
Dr. Dan Swartling wrote:
How does the K3 stack up against this kit:
http://estore.websitepros.com/1763214/Detail.bok?no=1
Dan
To make a difference, one must first be different.
___
Elecraft mailing list
Post
e now, who wouldn't, but I at last have an honest
assessment, ie I would hope to have shipment sometime during the next 13
weeks, unless advised further. That's OK by me, you also?
Chris G3SJJ
Stan Rife wrote:
No Jim, it used to be a unique reflector. Now it's just
patiently.
Have fun. Chris G3SJJ
Eric Swartz - WA6HHQ, Elecraft wrote:
I'd like to make a general statement about deliveries, status updates,
etc.
First of all, I'm primarily focused on getting K3s out the door each
day and as a result I only read the list every second or third d
x27;t have been sent if we were kept
properly informed.
Honesty first, radio whenever. Chris G3SJJ
Jason Milldrum wrote:
However, I've become
completely exhausted of this list turning into the "All K3 Bitchfest,
All Of The Time". I understand that some complaining is norma
eding ones
Chris G3SJJ
Don Wilhelm wrote:
By my count, it does look like there are now at least 30 K3s being
shipped per week over the past 2 week period, judging from the serial
numbers that have been posted on the wiki.
That means that Don Rasmussen's projections are overly pessi
seriously considering cancelling my order due to to the
combined effects of both.
Chris G3SJJ
Andreas Hofmann wrote:
Ditto, traffic from elecraft email list is getting out of hand with K3 support
emails IMHO...
73, Andy (KU7T, ex Y38WF, ex DL6UST)
-Original Message-
From: [EMAIL
capablity for the Acom so was
proposing to use normal phono to phono plus take 12v off the rear K3
connector. A bit messy compared with just a single Din connector on the
MP but now it seems I will need some other kind of interface as well.
Chris G3SJJ
Ian White GM3SEK wrote:
3. Reverse
required..
End.
Chrid G3SJJ
Tom Childers, N5GE wrote:
On Thu, 29 Nov 2007 17:12:38 +, you wrote:
Er, isn't that device called a PC?
A Pocket PC might be able to do this - no I don't have that skillset.
On 29/11/07 17:08, "Vic K2VCO" <[EMAIL PROTECTED]>
I had planned with the K3 in
July, September and October weren't so important although it would have
been a pleasant bonus, but Jan, Feb and March are very important for me,
so here's hoping!
Chris G3SJJ
Eric Swartz - WA6HHQ, Elecraft wrote:
I see there has been some confusion
t is
confusing and frustrating.
Chris G3SJJ
Greg - N4CC wrote:
Oh come on now, David...there is no "fiasco". The folks at Aptos are
doing a marvelous job. They've had to deal with things that just
"happen" when you have a complex production operation and are re
Yeah but how does it perform? Were you on the the various 160m contests
last night, did you work any DX, how did it cope with strong signals,
how did the NB react to the high static crashes that were around? There
are the real questions!!
Have fun Chris G3SJJ
Simon Brown (HB9DRV) wrote
30 ways to leave your lover - make a new plan, Stan
Stewart Baker wrote:
Slip sliding away, slip sliding away
You know the nearer your destination, the more you slip sliding away..
S&G
Stewart G3RXQ
On Mon, 12 Nov 2007 13:40:38 +0000, G3SJJ wrote:
Seems to me we are around serial nu
Whoops, I reads as though I ordered an assembled one. I should have said
I ordered a K3/100 kit.
Chris G3SJJ
G3SJJ wrote:
Seems to me we are around serial number 40, so just another 200 or so
in the next 17 working days to meet the taget for starting the 2nd
production run.
If a K3 takes
Rx may beginning of Feb. That's my take on the situation. I will
count anything quicker as a real bonus, and even a Christmas present!
Chris G3SJJ
Thom LaCosta wrote:
At 07:22 AM 11/12/2007, Barry McWilliams wrote:
What is the current shipping status - and - are you shipping
assembled
ght I was in the first production run and should therefore be
shipping before 29 November, (since the 2nd run is due to commence 30
November, which is a Friday.) I am £700 lighter and thoroughly confused.
Chris Burbanks G3SJJ
David Ferrington, M0XDF wrote:
I looked in my K3 orders folder a
Well you aren't far off David. My contact "on the inside" says they are
expecting them mid-December. I just got in at the end of the 1st prodn
run so just hoping I might get it in time for ARRL 10m Contest!
73 Chris G3SJJ
David Pratt wrote:
In a recent message, G3SJJ &l
I guess 8 of them must be on their way to the VP6 Ducie Island packing
depot by now, as all gear is going to be shipped in November according
to the VP6 website.
Chris G3SJJ
Don Rasmussen wrote:
The last reflector posted K3 serial number was #31.
Serial number #25 was the latest reported
(Would you like
to pay now, sir!) I would certainly prefer the Parcelforce £8 handling
charge and an additional day or so.
Chris Burbanks G3SJJ
Bryan wrote:
Hi,
My experience has been that any delay has always been here in the UK, either
Customs or ParcelForce.
Br
http://www.elecraft.com/K3/K3FAQ.htm#mic%20wiring
Chris G3SJJ
Ed Rodriguez wrote:
Sorry for the dumb question, but what configuration is the mic pin for
the K3 , ie; Kenwood 8 pin? what microphones are the field testers
using? what do you all recommend to use, Elecraft is selling the Hand
more time on 160m this winter!! I am really looking forward to
checking out the noise blanker on my local QRM source, 400kV overhead
power lines about 1.5km away.
Chris G3SJJ
Bill Tippett wrote:
Congrats Tree! I actually never heard him give your
call correctly. Here's what
Chris G3SJJ
Tom Hammond wrote:
Hi Ron:
I read in the previous postings that the CW sounded better on the K2
than the K3. That is a bit of a worry to me.
In general, I've received just the very OPPOSITE reports. Most say
that the K3 has some of the very BEST sounding keying that they'
Please read -
In an effort to reduce the overload of off topic comments hitting the list,
please refrain from the urge to post minor 'me too' or 'I disagree' comments,
or any criticisims or discussions on the appropriatness of a posting. If
someone complains about the shipping date, features
Please read -
In an effort to reduce the overload of off topic comments hitting the list,
please refrain from the urge to post minor 'me too' or 'I disagree' comments,
or any criticisims or discussions on the appropriatness of a posting. If
someone complains about the shipping date, features
Please read -
In an effort to reduce the overload of off topic comments hitting the list,
please refrain from the urge to post minor 'me too' or 'I disagree' comments,
or any criticisims or discussions on the appropriatness of a posting. If
someone complains about the shipping date, features
Guys, please don't take offence but this is just the kind of superfluous
posting that several of us are complaining about.
It would really help if these kind of things together with unrelated
topics such as we have seen recently could be reduced.
Thanks so much. Chris
been available for over 20 years in K0II, Logikey,
and ETM and now K1EL designs, yet it generated a whole string of
negative comments then a history of el-keyers.
Finish. I am now concentrating on working for 3B7C on 160 for my 8th band.
Chris G3SJJ (who also is courteous and adds his name and callsi
e system.
BTW, in the recent IARU SSB FD, we were using SR2O, otherwise known as
Big Knob Man and Little Knob Man. We used my GU8D-special (designed for
IOTA contest) SR2O unit for switching the mic, ie first one to hit the
footswitch grabs the tx. Good fun.
Chris G3SJJ
Stewart Rolfe wr
loung re-assembled
about a week before delivery of K3 do that the novelty factor of new
rads, new hole in wall fire, new plastering, new colour walls and new
wooden floor still means I am loved by my wife! Timing is critical.
Chris G3SJJ
David Honey wrote:
At 10:25 2007-07-09, G3SJJ wrote
There are some sill typos here. Apologies. I am hurrying because I am so
keen to get on with some decorating tasks!!
Chris G3SJJ
G3SJJ wrote:
Julian, I think Elecraft have realised they are into completely new
ball game with the K3. There are probably thousands of FT1k, FT2k,
Kenwood, Icom
ng my FT1kMP as the 2nd radio for
SO2R and MO contesting as I feel its is better ergonomically and ahs
better skirt slectivity with its Inrad roofing and IF filters.
73 Chris G3SJJ
Julian G4ILO wrote:
On 7/9/07, Thom LaCosta <[EMAIL PROTECTED]> wrote:
Strongly suggest you call your i
15m," you respond 21045 on the paddle and immediately type and enter
that. You're there. Complete the QSO and do the same for another band.
Chris G3SJJ
DOUGLAS ZWIEBEL wrote:
Dave:
Glad I'm not the only one who is thinking this way
de Doug KR2Q
-- Forwarde
Norma, patience is a virtue. Just get on the air and make some Qs whilst
you are waiting!
Chris G3SJJ
David Ferrington, M0XDF wrote:
If it doesn't hurry up and get here, I reckon I'm going to have lost too
many brain cells to use it. HiHi
Waiting, waiting, waiting .
On 29/
Easier than that - Work in :
Degrees
Metres
Litres
Euros
Way to go.
A young (62) G3SJJ. Chris Burbanks. Postal code NG12 5NX, D. O. B.
20-04-1945. Info freely given because I have no hangups about not
signing emails.
Ian Stirling wrote:
On Wednesday 27 June 2007 12:00:40 Don Wilhelm
buy a top of the range Nikon. Likewise if I had just
taken my driving test I would not expect to buy a Maseratti, Ferrari,
Bentley etc.
Chris Burbanks G3SJJ
Frank J. MacDonell wrote:
I got my Technician license in February and I am learning CW. I have
built a dipole and ordered a K3. What
On second thoughts Thomas, why not get delivery delivered until your
return so that someone else can be receive their K3 a littel earlier?
Chris G3SJJ
David Ferrington, M0XDF wrote:
Can anyone give me an idea of the time is takes for goods to reach the UK?
I'm away most of August a
the group for wasting your time.
What is really driving on this one is that if by some lucky chance my K3
arrived a few days before 28 July the IOTA Contest weekend I could
probably run SO2R!!
Exciting times!
Chris Burbanks G3SJJ, G8D
Brian Lloyd wrote:
On Jun 4, 2007, at 7:24 AM, lyle
which is
already in place, from the Notebook? It's a bit of a bind having to go
up to the main shack to turn the beam!
Sorry for the length, I though I would get rid of this one one go!
Chris Burbanks G3SJJ (G8D Contest Call)
___
Elecraft mailing
Notebook? It's a bit of a bind having to go
up to the main shack to turn the beam!
Sorry for the length, I though I would get rid of this one one go!
Chris Burbanks G3SJJ (G8D Contest Call)
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.ne
rn the business around if they were in
trouble or how to expand. I am sure both would have held Elecraft in
high esteem but would have disagreed with the idea of staying a QRP kit
supplier.
73 Chris G3SJJ
[EMAIL PROTECTED] wrote:
In a message dated 5/27/07 6:21:00 AM Eastern Daylight Time,
[
filling several growing markets sectors. Firstly the users like
yourselves, secondly the guys who want a US legal limit amp and finally
like myself and others who want 2 amps for an SO2R or multi-op station.
Chris G3SJJ
Bill W5WVO wrote:
[EMAIL PROTECTED] wrote:
IMHO I would like to see a &q
Yeah 3. Two for SO2R and one for Dxpeditions/Portable!
then you need a KPA160 and a KPA800
Chris G3SJJ
Simon Brown (HB9DRV) wrote:
- Original Message - From: "Simon Brown (HB9DRV)"
<[EMAIL PROTECTED]>
That's why you need 3 x K3, one fully loaded for home,
the top ten multi-op 1996 to 2005.)
Chris G3SJJ
Doug Person wrote:
Speaking for myself, I'm very pleased with the approach you've taken.
While my soldering skills are excellent and I enjoy the building
process very much, SMD's are out of the question for me. In the case
N A M E & C A L L ??
Yes, me too, glad I did, the pound has dropped 2 cents against the dollar
since then.
On 20/5/07 09:05, "[EMAIL PROTECTED]"
<[EMAIL PROTECTED]> sent:
Rowland
G4APO K2/K1/ KX1/ K3 fully paid to take advantage of the good exchange
rates.
I like the piece on the Hamvention Friday one where the new Yeasu rig is
said to be a winner with a 10KHz Roofing Filter! Yeah...so ...!
Chris G3SJJ
Toby Deinhardt wrote:
http://www.youtube.com/watch?v=NUxhVKfXf4k
vy 73 de toby
___
Elecraft
Band Decoder.
I brought a Topten DX Doubler back from my recent W5 trip so looking
forward to SO2R with FT1kMP / K3 combo.
It's the only way I can compete with you in the FOC Marathon!!
(Tree hugging, high power contester. Life's to short for QRP!)
73 Chris G3SJJ
Fraser Rober
Everyone's gone to the moon ... well, Dayton.
Chris G3SJJ
Corboy-Poteet wrote:
Sorry, I'm having having problems posting to the elecraft list and
thought I would try a really simple message as a test.
Mike W5FTD
___
Elecraft mailing
Yet another anonymous email
Chris G3SJJ
http://pfuca-store.stores.yahoo.net/
On 16/5/07 09:05, "[EMAIL PROTECTED]"
<[EMAIL PROTECTED]> sent:
Message: 37
Date: Wed, 16 May 2007 03:24:16 -
From: "Ken Kopp" <[EMAIL PROTECTED]>
Subject: [Elecraft] K
is now on order!!
Chris G3SJJ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://
amp phono socket and measure the open cct
voltage, I would guess between 30 and 100v, then put DVM into current
mode and measure closed cct current, again maybe around 70-100 mA.
(This will obviously switch the amp on.)
Off you go and work some DX!! Email me off list if you need more info.
73 C
Aristotle, no callsign.
Do you man on the K2 or the K3?
C h r i sG 3 S J J
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qt
t out
and report back until early April, so in the meantime you could email
Dave N3RD at Topten. He will answer your queries.
73 Chris G3SJJ
Randy Foltz wrote:
I'm looking at buying a DX Doubler and am wondering if the Kenwood
cables will work on a K2. The web site doesn't men
Yes, I did wonder about the K2DSP. Haven't got one here, yet! The mod
certainly makes a difference though.
Keep up the CW, Stewart!
73 Chris G3SJJ
Stewart Baker wrote:
Although I am not really a CW man I spent a few hours in the recent BERU
contest. After a while I began to get a bit
been reduced.
Chris G3SJJ
Sverre Holm wrote:
My L1 82 mH inductor has a DC resistance of 62 ohms. This is quite different from the 180 ohm version used in the mod. Would a series resistor be desired as Fred indicates in the message below? I have 100 ohm, 120 ohm, and 150 ohm resistors on
Every time I try this I get an error message. Any thoughts? Chris G3SJJ
http://video.google.com/videoplay?docid=2943570522939177086&hl=en
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the
1 - 100 of 120 matches
Mail list logo