to the KAT500?
From: Jeff Hall
To: Michael Walker ; Harry Yingst
Cc: Elecraft Reflector
Sent: Saturday, February 14, 2015 9:22 PM
Subject: Re: [Elecraft] My KAT500 seems very sensitive to common mode RFI
Thanks everyone for their replies to my problem. I read Jim Brown's pap
n chokes
I just installed my KAT500 today and considered taking thepower lead and
wrapping it around a snap on choke a few times.
From: "Jeff Hall, W6UX"
To: Elecraft Reflector
Sent: Saturday, February 14, 2015 12:48 PM
Subject: [Elecraft] My KAT500 seems very sensitive to common mo
guess the frequency is
just too low for them to be effective (or perhaps I'd need like 50 of the
suckers!)
-Jeff
On Saturday, February 14, 2015 10:06 AM, Jim Brown
wrote:
On Sat,2/14/2015 9:48 AM, Jeff Hall, W6UX wrote:
> can anyone suggest some further experiments to try?
Yes. T
I have a Hex Beam and a 40m wire vertical w/ two elevated radials. I have been
fighting what appears to be a common mode RFI problem which causes the KAT500
to continuously power cycle as long as the K3 is transmitting. Generally this
only occurs when driving my KPA500 amp beyond a certain out
My KAT500 is getting power-cycled in CW and RTTY modes at various drive levels
from the K3 on different bands. I can run SSB full power with no problems at
all, and receive superb audio reports (no hint of RF in my transmissions). I
am thinking I have either an excessive voltage drop on the AC
I have noticed that my LINE IN jack sometimes loses the input signal and I have
to apply a slight pressure to get it restored (gently push in on it). It's
fine after that unless I move the K3. Does this jack suffer the same issues as
the headphone jack too?
Sent from my iPhone
> On Jan 23, 2
I just finished building my KAT500 and KPA500. I am trying to integrate them
into my existing setup consisting of a K3, P3, and Microham Microkeyer II.
This setup was working fine before I cabled up the new equipment, and now I am
having some issues.
All hardware has been updated to the latest
the K-Line gear.
I picked the 0.1-200W directional coupler as I wanted to put the W2 between the
K3 and the KPA500. Is it worthwhile adding the second coupler for 1-2000w? I'm
assuming you only use this if you want to place the W2 after the KAT500?
Thank you all for any suggestions!
Jeff H
Mike, thank you very much! The problem was as I suspected, operator error! The
outer AF knob was fully counter clockwise. Restoring this knob to the 12:00
position restored VFO reception in my right ear. It must have gotten knocked
by someone using my rig at Field Day. What a relief!
73, Jef
I haven't used my K3 much since Field Day. Today I turned it on and engaged
the sub receiver by tapping SUB. Instead of hearing VFO B in my right ear, I
only hear VFO A in my left ear.
Adjusting the SUB RF control affects VFO A volume. It's like the radio's sub
receiver configuration got mes
vorite trx of
many ops. Everybody loves the diversity.
So if finance is not a problem, duplicate the filters.
73
Arie PA3A
Op 2-3-2013 20:34, Jeff Hall schreef:
> Hi everyone,
>
> I need advice on picking filters for a KRX3.
>
> I currently have the following filters in my K3:
&
Hi everyone,
I need advice on picking filters for a KRX3.
I currently have the following filters in my K3:
2.7 kHz 5 pole
1.8 kHz 8 pole
400 Hz 8 pole
Should I put the same filters in the KRX3? At this time, I don't have the
capability to take advantage of "diversity receive". It's been a w
I've found that using VOX outdoors is problematic due to background noise, so
I'd like to wire up a finger PTT switch that works with my K3 and Yamaha CM-500
headset. I have an existing finger PTT switch that was designed for use with a
Yaesu FT-11R HT. There are 3 stereo plugs wired to the f
I'm heading to Anacapa Island in 3 weeks for the IOTA contest. Taking a 1 hour
boat ride from Los Angeles to get there.
I've never taken my K3 out of my shack so I need recommendations on a case and
proper packing to get it there safely and back. I heard Pelican was a good
choice, and Frys ha
Hi,
I noticed during the CQ WPX RTTY contest that often the RF meter was fully
pegged with the power set to 100 (the last two bars past the 100 mark).
Shouldn't it be lit only to the 100 mark?
I did all the calibration procedures when I originally built the radio back
in March 2010. I just upda
Mike,
I messed around with the TX EQ for over an hour yesterday, I've settled on
these settings for now (this sounded "less nasal" and not too much like I
had a pillow over my face)
*50 Hz @ -16dB*
*100 Hz @ -16dB*
*200 Hz @ -6dB*
*400 Hz @ +8dB*
800 Hz @ +0dB
1600 Hz @ +0dB
2400 Hz @ +0dB
3200 H
Thanks to everyone who offered their suggestions!
I am not sure what happened, but the problem cleared up simply by accessing
my uRouter software for the MKII and toggling from Front mic to Rear, then
back to Front. Once I did this I immediately noticed the CMP and ALC bars
back to their desired
I'm having problems preventing my Yamaha CM500 boom mic from cutting out
intermittently while talking. I have the following settings on my K3:
VOX Gain: 85
Anti-vox: 0
Mic delay: 0.90
Mic Gain: 30
Cmp: 25
The mic is routed to the K3 via a microHam MKII.
I have tried moving the mic to various po
>I've already noted that I should provide advice regarding per-mode AGC
>slow/fast and other AGC settings. What other areas would you like to
>see additional guidance in?
>
>73,
>Wayne
>N6KR
Wayne,
I've had my K3 for nearly a year, and have only been on HF for about 1 year.
My background is soft
Thanks Gary and "The Smiths" (great 80s band, BTW!) for those very helpful
pointers! Can't wait to try those techniques out tonight!
73 de Jeff, W6UX
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: ht
Hi, I've been searching for some operating tips on how to strategically
employ the following K3 controls:
- NOTCH
- NR
- NB
- WIDTH
- SHIFT
As good as the manual is, I still feel like I don't understand how these
really work and when I should use them to get the best possible results. To
da
Well it appears I may have had the wrong sideband mode activated on the
various bands I was trying to tune. Doh!
Thanks,
Jeff, W6EZY
--
View this message in context:
http://n2.nabble.com/New-K3-speech-reception-is-all-distorted-SSB-tp4633791p4637406.html
Sent from the [K3] mailing list archiv
I'm attempting to use my K3 for the first time. I *think* I completed all
calibration steps as per the manual (synthesizer, TXCO 1ppm, Tx gain). I
hooked up the K3 to my antenna this morning and tuned to 10 MHz. WWV came
in just fine and clearly understandable on LSB or USB. However, I seem
una
Hello all,
I need help picking out a proper dummy load to use for calibrating my new
K3. HRO is just up the road and they carry some of the less expensive MFJ
dummy loads -- would these be sufficient? Not looking to spend a lot of
money, but don't want to buy junk either. What factors should I c
Greetings all,
This is my first submission to the Elecraft reflector. I intend to place an
order for my K3 today, but I need some help making the final decisions of
which options I should purchase at this time. First, let me describe my
antenna setup so the experts here can hopefully offer more
25 matches
Mail list logo