Just some notes for future folks reading this.
I always replace D1 and Q6 together.
Other notes re Q6 and D1;
1. Poor RX on 24 and 28Mhz 12m 10M only and TX gain is OK. Q6 a 2N7002,
OR D1 on the LPA can Suck the RX down on these two bands!!
2. Slow ramp up of TX power output. Typically worse
Hi all,
just wanted to let you know that my K3 is back again with full output power.
We found the Diode D1 on the LPA board. On the anode side, it had shown full
power, on the other side, nothing. When unsoldering it, it was already very
loose. The diode itself was intact, but had no contact
Chris;
Since you EE INIT-ed your radio, you MUST re-load a known-good saved
configuration!
Or setup all options, filters etc and do the transmit gain calibrations.
An EE INIT reset blanks the radio and sets it to ONE filter, (a 2.7,
with no offset, in slot 1).
Keith WE6R Elecraft K3/K4 Tech
Hello,
together with Harald DD0VS, we narrowed it down to the diode D1 on the LPA
board. I will now order the diode and some probably affected parts around the
diode and start replacing and testing again.
I will report again.
Many thanks to all others with giving different hints!
73s Chris
On 3/24/2021 9:28 PM, Christian Janssen DL1MGB wrote:
I don't have a spectrum analyzer, but I will look with my eyes if there is
something noticeable.
A frequency counter can also be a useful RF probe for your own TX
73, Jim K9YC
__
;>>
>>> DD0VS
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>> Gesendet von Mail <https://go.microsoft.com/fwlink/?LinkId=550986> für
>>> Windows 10
>>>
>>>
>>>
>>> *Von: *Chr
>>
>>
>> Gesendet von Mail <https://go.microsoft.com/fwlink/?LinkId=550986> für
>> Windows 10
>>
>>
>>
>> *Von: *Christian Janssen DL1MGB <mailto:ch...@dl1mgb.com>
>> *Gesendet: *Mittwoch, 24. März 2021 21:05
>> *An: *elec
gt;
>
>
> *Von: *Christian Janssen DL1MGB <mailto:ch...@dl1mgb.com>
> *Gesendet: *Mittwoch, 24. März 2021 21:05
> *An: *elecraft@mailman.qth.net <mailto:elecraft@mailman.qth.net>
> *Betreff: *[Elecraft] K3 - no output power
>
>
>
> Hello,
>
>
>
&
arch 24, 2021 1:49 PM
> *To: *Harald Fritzsche (DD0VS) <mailto:harald.fritzs...@dd0vs.de>;
> elecraft@mailman.qth.net <mailto:elecraft@mailman.qth.net>
> *Subject: *Re: [Elecraft] K3 - no output power
>
>
>
> Hi Harald,
>
>
>
> spectrum analyzer and m
@mailman.qth.net
Subject: Re: [Elecraft] K3 - no output power
Hi Harald,
spectrum analyzer and more space on the table would be the best, but both not
available :-)
Additional information:
- internal voltage / current (DISP)
Standby: 13.8 V / 0.86 A
Tune: 13.4 V / 3.20 A
And still no power output
Does it receive?
Wes N7WS
On 3/24/2021 1:03 PM, Christian Janssen DL1MGB wrote:
Hello,
it happened during the Russian DX Contest last Saturday, from one second to
another. No output. When I tune the display looks like this:
http://dl1mgb.com/temp/k3_no_power.jpg
Following conditions:
-
.com>
> *Gesendet: *Mittwoch, 24. März 2021 21:05
> *An: *elecraft@mailman.qth.net <mailto:elecraft@mailman.qth.net>
> *Betreff: *[Elecraft] K3 - no output power
>
>
>
> Hello,
>
>
>
> it happened during the Russian DX Contest last Saturday, from one se
Hello,
it happened during the Russian DX Contest last Saturday, from one second to
another. No output. When I tune the display looks like this:
http://dl1mgb.com/temp/k3_no_power.jpg
Following conditions:
- sending into a 50 ohm dummy load
- no matter how many watts are set with PWR knob
-
I have the same thing here, Bruce. Something in firmware was
changed a while ago and when I reported it to Wayne, he said
that it is within specs.
73, Ken K3IU
~~~
On 1/9/2016 11:09 AM, Bruce Meier wrote:
Today I noticed that the output power on
This has nothing to do with the new synth. We're hoping to have another
firmware release dealing with it soon. I've been working on other issues.
73,
Wayne
N6KR
On Jan 9, 2016, at 8:09 AM, "Bruce Meier" wrote:
> Today I noticed that the output power on 15 meters does
I noted a similar issue and found that increasing the power supply voltage a
bit returned full output. I think I have about 14.2v at the rig in receive
mode. This was before I updated the synths so I don't think it's related to
that.
Vic 4X6GP/K2VCO
> On 9 Jan 2016, at 6:09 PM, Bruce Meier
I suppose "spec" would be about 1 dB or so. If so, then somewhere
between 80 and 125 watts would be about right for a nominal 100 watt
radio. I, however, didn't see and published spec for transmitter power
in my K3S manual.
73
Bob, K4TAX
On 1/9/2016 10:27 AM, Ken K3IU wrote:
I have the
Today I noticed that the output power on 15 meters does not reach 100w. The
max, according to the front panel meter reading, is 93w. So, I ran the
transmitter gain calibration and it did not help. I decreased the power to
90w and it reached 90w, so I gradually increased the power and it is fine
Will the 1mw calibration have an effect on power output from the K144XV?
I do not know if my Fluke 77s are an accurate RF voltmeters.
Can I use an oscilloscope to adjust for 1mw?
What P-P voltage setting should I set it to?
Requested = RF Wattmeter at .224 Vrms = .6336 V p-p on scope
Back in volume 117, issue 39 there was some chatter about having no output
power from a K3. Whatever became of that issue? I have seen nothing since.
I have a K3 that has no output power. If I key the rig while listening
with an external receiver, I can hear what I am keying on the frequency
Don, San,
Many thanks for your detailed advices.
I have set up as you advised. Output in DATA A mode became stable with
occasional glitch.
I think I need to find the best setting for my system.
Thanks again for your excellent advices.
73 de JH3SIF, Keith
2014/01/31 6:27、Sam Morgan
Output power of my K3/100, SN 79xx, without KAT3 is very unstable in DATA A
mode. The symptom is;
1. With setting 100W output on 14MHz and 10MHz, I get 100W output for a couple
of seconds, then suddenly the output goes down to 10W or so.
2. On 7MHz and below, the output power never go up to
Keith,
Have you adjusted your audio input to produce 4 bars solid on the ALC
meter with the 5th bar flashing?
If not, please do so - you can do that with the K3 in TX TEST mode so no
signal is transmitted.
After you set the audio level correctly, then adjust the power knob to
the desired
then using the K3 in DATA A mode
this often is caused by incorrect audio levels
the k3's audio level should show 4 bars with the 5th bar flickering
I have run my K3 with the 5th bar solid and it still worked ok
the power out level is set by the K3's PWR knob
most other rigs have a different
:
From: Ian White gm3...@ifwtech.co.uk
Subject: Re: [Elecraft] K3 Erratic output power
To: 'Wes Stewart' n...@yahoo.com, 'Elecraft Reflector'
elecraft@mailman.qth.net
Date: Monday, March 4, 2013, 12:06 AM
When first assembling the RF output connector and the KANT3/KAT3 board,
I didn't like
...@mailman.qth.net [elecraft-boun...@mailman.qth.net] on
behalf of Ian White [gm3...@ifwtech.co.uk]
Sent: Monday, March 04, 2013 1:06 AM
To: 'Wes Stewart'; 'Elecraft Reflector'
Subject: Re: [Elecraft] K3 Erratic output power
When first assembling the RF output connector and the KANT3/KAT3 board,
I didn't
Has anyone come up with a permanent fix for the erratic output power problem?
I'm not talking about the 100W PA issue, but the issue solved (temporarily)
by loosening and re-tightening the screws in the metal standoff on the output
board near the coax connector.
According to Murphy's Law,
Wes,
I believe Elecraft has already implemented a fix for that in later K3s
(starting about a year ago) - at least there was talk about doing it and
supplying one 2D connector that was different then the others (with
threads removed from thee hole).
Removing the threads from the center hole
I'll give that a try. Believe it or not, I worked TX5K on 20m RTTY while
thumping the case during my exchange transmission.
--- On Sun, 3/3/13, Don Wilhelm w3...@embarqmail.com wrote:
From: Don Wilhelm w3...@embarqmail.com
Subject: Re: [Elecraft] K3 Erratic output power
To: Wes Stewart n
-boun...@mailman.qth.net [mailto:elecraft-
boun...@mailman.qth.net] On Behalf Of Wes Stewart
Sent: 04 March 2013 01:45
To: Elecraft Reflector
Subject: [Elecraft] K3 Erratic output power
Has anyone come up with a permanent fix for the erratic output power
problem? I'm not talking about the 100W PA
Hello,
since mounting firmware 4.60, I have noticed that when I use WSJT software in
K3 transverter mode
the output power (0-1mW) is unstable. I see this expecially when I start new tx
sequence.
With previous firmwares , I didn't have any trouble.
Does someone have this trouble, or similar
Further info:
I sat down today and performed another firmware load per Fred's sequence
with no change. I then tested for any heat generation from the driver
and finals of the LPA module and could not detect any.
I dug out my old Tek 475A scope and did some signal tracing and verified
that I
Thanks for all the replies. I will try these suggestions tomorrow
(working today) and post my results to the list for future reference. I
will try the heat test on the LPA finals and driver first as I have all
the panels off and it will be a quick way to find out if that is where
the problem
Hi all,
Before I contact service, I thought I might post my problem here in case
it is something fairly simple.
I returned from a 2.5 week vacation a couple of weeks ago and sat down
to do the firmware upgrade to my K3. I had my K3 powered off and
disconnected the antenna while away but it
If I remember correctly, there are two different audio amplifier circuits in
the K3. One for the speaker and one for the headphones (or, it may be more
complex then that).
Does anyone know the power output level of the speaker audio amplifier?
73, phil, K7PEH
The LM4950 is rated at 3.1W per channel to a 4 Ohm
load with 1% THD+N.
The spec sheet shows THD increasing significantly once
output goes above about 2.3W into 4 Ohms, above about
1.8 Watts into 8 Ohms and above about 900 mW into 16
Ohms at 12V. THD is below 0.03% until the knee is
reached.
hb9ari wrote:
DATA A is perfectly usable with VOX: i will migrate to this mode
But there is no reason to use VOX for any digimode. WSJT supports PTT
control. You have a fully wired serial cable connecting the PC and K3 which
allows you to use it. The K3 is not like other radios
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Julian, G4ILO
Sent: Thursday, November 12, 2009 9:34 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] [K3] JT65A output power variations
hb9ari wrote:
DATA A is perfectly usable with VOX: i will migrate
Joe Subich, W4TV-4 wrote:
This does not work if one has a logging program that is
using the K3's RS-232 port. As far as I know, no commonly
used operating system permits more than one program to
access a serial port at the same time which means that WSJT
can not access the RTS/DTR
Julian,
I will look if this connection don't interfere with other programs
and if ok, i will use it!
Thanks for info!
73, Rudolf
Julian, G4ILO wrote:
hb9ari wrote:
DATA A is perfectly usable with VOX: i will migrate to this mode
But there is no reason to use VOX for any
You could also use LP Bridge to share the serial port at the K3 among
several programs running on your PC. This works quite well.
73,
matt W6NIA
On Thu, 12 Nov 2009 16:34:04 +0100, you wrote:
Julian,
I will look if this connection don't interfere with other programs
and if ok, i will use it!
Hi Matt,
I've tried to use LP-Bridge with PowerSDR-IF (and LP-Pan) but with some
losses
of communication after some time; for this reason, i use HRD with Power-SDR
without lock during many hours ( waiting for 50MHz apertures during
Summer...).
73 QRO,
Rudolf
Matt Zilmer wrote:
You could
Some things to check...
- Check: Config TX INH needs to be set to false
- Be sure that you are not in the test mode (TX is blinking) -- Press and
Hold Mode Up/test to toggle
- Connect dummy load, and press hold XMIT/Tune -- if this works, then
the hardware is probably OK.
- If in CW, Press
My newly assembled K3 has no power output. I have tried all the
configuration settings that might affect output. I have checked all the
assembly procedures to assure I did all correctly. The 100 watt amp is not
yet installed. I am convinced I have a hardware problem. I have sent a
request for help
Hello all,
I am confused about the output level of the K3. What is the output power
level of the 10 Watt version of the K3?. Is it the same on all bands? Do I
have to reduce the output below 10 watts to avoid poor transmit intermod on
SSB? I am asking this because I use my present K2 QRP radio
@mailman.qth.net
Subject: [Elecraft] K3 QRP output power level
Hello all,
I am confused about the output level of the K3. What is the output power
level of the 10 Watt version of the K3?. Is it the same on all bands? Do I
have to reduce the output below 10 watts to avoid poor transmit intermod on
SSB
Rich,
The K3 output power is equal to or greater than the K2, so you should
not have a problem. In addition, the K3 offers the ability to remember
a power setting for each band, and that would likely be helpful when
driving your amplifier.
73,
Don W3FPR
Richard Haendel wrote:
Hello all,
Sorryshould have indicated the above message is for K3!!
Humbled (again)
Stewart, GW0ETF
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
I have not yet determined the exact series of events, but something strange
happens to both of my K3s. This weekend I have been participating in the
Texas QSO Party. As it is both a CW and SSB event and multi-band I am doing
jumps from band to band and mode to mode. Many times I get to the
My K3 setup is configured to put out about 30W on PSK31, with my sound card
dedicated to APSK/AFSK modes and its output locked in place to make that power
level at 1250 Hz. My TX IMD is excellent.
However ... if I select a PSK31 spot where the resultant audio frequency is
below, say, 800 Hz,
Do you have TX EQ set?
Leigh/WA5zNU
My K3 setup is configured to put out about 30W on PSK31, with my sound card
dedicated to APSK/AFSK modes and its output locked in place to make that power
level at 1250 Hz. My TX IMD is excellent.
However ... if I select a PSK31 spot where the resultant
Steve,
If you have the TX EQ set for a corresponding rolloff, then the answer
is yes. Currently there is only one TX EQ that applies to all modes.
Someday (soon) you can have separate TX EQ settings, but right now, TX
EQ is TX EQ no matter what.
73,
Don W3FPR
Steve Jackson wrote:
My K3
I have excactly the same problem, also awaiting an answer
Ian J Maude wrote:
OK, I was waiting to see if the firmware sorted this but it has not. If
I hold tune or use a key, I get full output power on my external meter.
On SSB I get about 40-50W showing on peaks for a setting of
OK, I was waiting to see if the firmware sorted this but it has not. If
I hold tune or use a key, I get full output power on my external meter.
On SSB I get about 40-50W showing on peaks for a setting of 120W. This
is the same whether into my trusty old Sommercamp YP-150Z or via the
Bird
hello ian and the list
i have the same probleme here with serial 153
set to 100w and ssb only 40 to 45 W
73 terry F5MOO
K3 #153
Ian J Maude a écrit :
OK, I was waiting to see if the firmware sorted this but it has not.
If I hold tune or use a key, I get full output power on my external
I have one of the new SPE Expert amps on order:
http://www.linear-amp.com/
It requires 20W of drive for full output. Can one of the knowledgeable K3
designers/testers comment on nominal Po from 160--6M?
Tnx,
Dale W4OP
___
Elecraft mailing list
Sent: Tuesday, July 03, 2007 9:46 AM
Subject: [Elecraft] K3/10 OUTPUT POWER
I have one of the new SPE Expert amps on order:
http://www.linear-amp.com/
It requires 20W of drive for full output. Can one of the knowledgeable K3
designers/testers comment on nominal Po from 160--6M?
Tnx,
Dale W4OP
I've been seeing about 14-15 watts but have not checked on 6m yet. Will do so
this
evening and report back.
So far every contact has reported a very nice clean signal. Excellent CW note
and
audio quality using the 2.8 kHz filter for SSB TX. The TX EQ really makes a
difference as well.
] K3/10 OUTPUT POWER
I have one of the new SPE Expert amps on order:
http://www.linear-amp.com/
It requires 20W of drive for full output. Can one of the
knowledgeable K3 designers/testers comment on nominal Po from 160--
6M?
Tnx,
Dale W4OP
On 7/3/07, Dale Parfitt [EMAIL PROTECTED] wrote:
I have one of the new SPE Expert amps on order:
http://www.linear-amp.com/
It requires 20W of drive for full output. Can one of the knowledgeable K3
designers/testers comment on nominal Po from 160--6M?
Why not drive it at 10W and get a cleaner
60 matches
Mail list logo