Make sure your com port is not in use by something else.
On 09/08/2020 3:55 p.m., Hank Garretson wrote:
Windows 10.
P3 Utility Ref 1.16.3.15
Connects to my P3 just fine.
When I click on Configuration Tab, both Save and Restore options are grayed
out.
Help please. What am I doing wrong.
Windows 10.
P3 Utility Ref 1.16.3.15
Connects to my P3 just fine.
When I click on Configuration Tab, both Save and Restore options are grayed
out.
Help please. What am I doing wrong.
Ham, Cope Exuberantly,
Hank, W6SX
__
Elecraft
OK thank you.
> On Jul 25, 2020, at 9:56 AM, Grant Youngman wrote:
>
> The blinking red light is normal. Indicates the onboard processor is working.
>
> Grant NQ5T
>
>> On Jul 25, 2020, at 12:48 PM, Michael Gillen via Elecraft
>> wrote:
>>
>> My P3SVGA board is acting up and there is a
The blinking red light is normal. Indicates the onboard processor is working.
Grant NQ5T
> On Jul 25, 2020, at 12:48 PM, Michael Gillen via Elecraft
> wrote:
>
> My P3SVGA board is acting up and there is a blinking red light on the board
> (did not notice that before because the lid was
My P3SVGA board is acting up and there is a blinking red light on the board
(did not notice that before because the lid was always on).
Is the blinking red light bad? If yes, is there something I can do about it?
My symptoms are that I am unable to successfully load the FPGAx firmware - it
I have a "no options" P3 for sale. With cables for the K3. I do not have the
CBLP3Y KIO3B RJ45 cable. Please contact me directly if you're interested.
lladerman AT earthlink DOT net
73, Lou W0FK
--
Sent from: http://elecraft.365791.n2.nabble.com/
On Wed, Jul 22, 2020 at 2:53 PM HP wrote:
> Is there a way to use the P3 utility image grabs -while connected to the
> K3S using the
> USB to computer - then the CBLP3Y RJ-45 to DE9s and DE9P Y adapter
Yes. Just connect the P3 Utility to the K3 virtual serial port.
> while using N1MM
Is there a way to use the P3 utility image grabs -while connected to the K3S
using the
USB to computer - then the CBLP3Y RJ-45 to DE9s and DE9P Y adapter while
using N1MM
logging program.
ALSO __Is there a way to use the P3 utility image grabs -while connected to the
K3 if the
RS232 is
FWIW: The KX3 shares the same wonky behavior.
Plus inconsistent quirks about forgetting "Scale" and "Ref" settings.
Esp after band/mode changes.
Supporting and remembering separate settings for: CW vs. "voice"
widths for "Span" would be a welcome improvement.
Bruce W2SE
On 7/18/20
This has been discussed several times before Jim. I haven't taken the
time to figure out the exact steps necessary to make it happen [come
back to the original band with the center frequency offset] but it seems
to be intrinsic to the design of the P3.
73,
Fred ["Skip"] K6DGW
Sparks NV
Doesn’t the P3 get its frequency from the radio?
Sent from my iPhone
...nr4c. bill
> On Jul 18, 2020, at 8:12 AM, Jim McDonald wrote:
>
> Why doesn't the P3 always remember the same center frequency when returning
> to the band?
>
> Jim N7US
>
Why doesn't the P3 always remember the same center frequency when returning
to the band?
Jim N7US
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Please direct your response off list.
--
73, Charles N2SO
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
Hey guys, accidentally hit the “Send all firmware to P3” instead of “Send all
NEW firmware to P3” and I keep getting “Block 657 write failed” for all the
“FPGA” updates. Tried it twice same result. Any thoughts?
P3 seems to work just fine. Added the SVGA board this afternoon. Just want to
get
Looking for a P3 SVGA kit. If anyone has one for sale, please let me know.
Thanks,
Bob Hughes
W7SNR
Cave Creek, AZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
I've just reassembled my double K-line station after a move. Everything
is working properly with the exception of one of my P3s. When I attempt
to power it up, I just see a rapidly flashing boot loader message for a
few seconds and then it turns off. This happens with or without
connection to
It’s a continuation of the IF from the radio. You can connect an SDR receiver
there for instance.
Sent from my iPhone
...nr4c. bill
> On May 19, 2020, at 5:19 AM, "a4...@sy-edm.com" wrote:
>
> I see on my P3 that there is an additional BNC output, which is
> “un-buffered”….
>
> Is there
I see on my P3 that there is an additional BNC output, which is “un-buffered”….
Is there any way I can use this ?
What actually is in this output I/Q only - or RF
More curious than anything …
Regards
Tim
__
Elecraft mailing
Indeed! Thank you Grant, I never touch that button and it's in a shadow
behind the corner of the computer monitor. Actually, I forgot it was
there. [:=)
73,
Fred ["Skip"] K6DGW
Sparks NV DM09dn
Washoe County
On 4/30/2020 1:26 PM, Grant Youngman wrote:
I was thinking PX3. On the P3 it's
I was thinking PX3. On the P3 it's DISPLAY …
Grant NQ5T
> On Apr 30, 2020, at 4:21 PM, Grant Youngman wrote:
>
> Press “DISP” on the P3 and see if it comes back …
>
> Grant NQ5T
>
>
>> On Apr 30, 2020, at 4:11 PM, Fred Jensen wrote:
>>
>> The waterfall on my P3 disappeared. I suspect
Press “DISP” on the P3 and see if it comes back …
Grant NQ5T
> On Apr 30, 2020, at 4:11 PM, Fred Jensen wrote:
>
> The waterfall on my P3 disappeared. I suspect it might have been associated
> with starting N1MM+ but I don't know that. The "Waterfall" menu setting
> shows the screen split
The waterfall on my P3 disappeared. I suspect it might have been
associated with starting N1MM+ but I don't know that. The "Waterfall"
menu setting shows the screen split like I want it, but when I exit that
menu item, the WF is still missing. Any suggestions?
73,
Fred ["Skip"] K6DGW
Sparks
Of course, that's for the K3. The P3 doesn't have beep tones.
Alan N1AL
On 2020-04-26 20:02, M. George wrote:
> Go to the CONFIG SW TONE setting and change it to ON (the default).
>
> Max NG7M
>
> On Sun, Apr 26, 2020 at 7:32 PM Mike March wrote:
>
>> On my P3, the beep function has been
Go to the CONFIG SW TONE setting and change it to ON (the default).
Max NG7M
On Sun, Apr 26, 2020 at 7:32 PM Mike March wrote:
> On my P3, the beep function has been disabled. I cannot find a reference
> to this in the manual. Has anyone else had this happen? Thanks.
>
> --
> Michael March
On my P3, the beep function has been disabled. I cannot find a reference
to this in the manual. Has anyone else had this happen? Thanks.
--
Michael March K4QU
242 Clay Hill Dr.
Winchester, VA 22602
mikek...@gmail.com
540-662-4279 home
540-539-8500 cell
In the TX Monitor Menu, check that "Mod En" is enabled.
Alan N1AL
On 2020-04-10 21:48, Tom and Karen Norris wrote:
> I've been almost 2 years getting to this point of assembling the P3 Kit.
> The K3s I got to right away. Now that I have the P3 together and working
> the only problem I have
I've been almost 2 years getting to this point of assembling the P3 Kit.
The K3s I got to right away. Now that I have the P3 together and working
the only problem I have is I cannot get the CW Split signal to show on the
P3 display. I've gone through the Fred Cady (what a life saver! We will
miss
Hi Dave,
Using the setup described at:
https://www.nk7z.net/adding-external-keypad-k3/
I have been unable to swap to a KBD from the Genovation. I direct swap
fails, so prior to purchasing a switch, do a manual replace to insure it
works for you...
Macro Loading is by hand, using that God
I am in the process of getting a Genovation KeyPad working with the
P3/SVGA but also want to have the keyboard available as I like to run
RTTY and CW without the computer. So I have a few questions:
1) Has anyone found a USB switch that would allow selectable use of a
keyboard or the
Jerry
For #1 there are a couple of things a) in menu set one of the function
buttons to "knob tap" and "knob hold" the select knob takes more
pressure so using one of the function buttons is much less force. b) I
have my K3s and P3 mounted to a single board, I put the bails down and
then
-Original Message-
From: ae...@carolinaheli.com
Sent: Thursday, February 20, 2020 10:00 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 Goodness and questions
I recently obtained a P3 and I'm and exceedingly happy! Now that I own it I
feel bad that I wasted a few years trying other
On 2/20/2020 11:52 AM, Bill Frantz wrote:
I built a special clamp that goes over the top of my K3 and keeps the P3
on top from sliding backwards out of aluminum bar. Tightening the screws
on the both ends clamp it to the K3 so it doesn't slide.
Yes. My K3s are tilted with the standard bale,
Hi Jerry,
I found on the Elecraft site under P3 mods, 3 mods 1 Mod to early K3's not K3S
Buffer gain 2 Holder clip for the P3 ribbon cable 3 How to assemble
PowerPoles Ask Elecraft parts about the screwI agree Nifty Accessories has good
"cheat" sheets
73Jim Hk7sss
In a message dated
I have used a rubberized mat material designed for lining kitchen shelves to
keep keyer paddles in place. That may work for a P3 as well. Something like
“gorilla grip”. There are a number of choices.
73 de Dick, K6KR
> On Feb 20, 2020, at 09:02, ae...@carolinaheli.com wrote:
>
> I recently
than it took me to write this email.73,Gary
K9GS
Original message From: Bill Frantz
Date: 2/20/20 1:52 PM (GMT-06:00) To: ae...@carolinaheli.com Cc:
elecraft@mailman.qth.net Subject: Re: [Elecraft] P3 Goodness and questions On
2/20/20 at 10:00 AM, ae...@carolinaheli.com wrote:>1.
My P3 sits beside my K3S and both use the elevation bail to raise the front of
the radio and P3 along with my KPA500. I don’t find that any of the 3 pieces
move when operating.
Bob, K4TAX
Sent from my iPhone
> On Feb 20, 2020, at 2:06 PM, Bill Frantz wrote:
>
> On 2/20/20 at 10:00 AM,
On 2/20/20 at 10:00 AM, ae...@carolinaheli.com wrote:
1.When using QSY the P3 unit often slides. How do most of you prevent
the unit from sliding?
I built a special clamp that goes over the top of my K3 and
keeps the P3 on top from sliding backwards out of aluminum bar.
Tightening the
**K6DGW comments interspersed:
73,
Fred ["Skip"] K6DGW
Sparks NV DM09dn
Washoe County
On 2/20/2020 7:00 AM, ae...@carolinaheli.com wrote:
I recently obtained a P3 and I'm and exceedingly happy! Now that I own it I
feel bad that I wasted a few years trying other solutions that introduced
noise
, 2020 10:01 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 Goodness and questions
I recently obtained a P3 and I'm and exceedingly happy! Now that I own it I
feel bad that I wasted a few years trying other solutions that introduced
noise and undue complexity into my station.
Just a few
I recently obtained a P3 and I'm and exceedingly happy! Now that I own it I
feel bad that I wasted a few years trying other solutions that introduced
noise and undue complexity into my station.
Just a few notes and questions because the manual is helpful but I don't
fully understand what I'm
Hi ,
I have a K3S and P3 with VGA card to run another display and was expecting to
see a duplicate of the P3 screen in larger format. It’s true I can see the
waterfall and data decode, but not seeing the tx signal status. If this is its
limit, I’d probably say the vga card is unnecessary.
Amazon will be happy to supply you a doodle cable that converts the VGA to
HDMI.
If you have noticed that the newer idiot surround sound boxes won't play
your LP's or CD's you can get doodle cables for that problem too.
Always a problem when new standards change everything. Some one always has
a
WTB: Elecraft P3, P3SVGA, DCHF-200, P3TXMON (optional)
Shipped 29708
Respond off list please.
Jerry Moore
AE4PB
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net
Hi all,
I just finished installing and setting up the SVGA option for my P3. All
appears to be working fine, except the spectrum is displayed differently on the
monitor than on the P3 itself. The signals sit above the horizontal divider
rather than immediately at it. When adjusting the ref
As a rule I set the REF LVL such that the no signal band noise is about
the bottom of the display. Then I set the SCALE to display the
strongest signals on the band at the top of the display. These will
change from band to band and antenna to antenna.
Otherwise, with a dummy load on the
I find that there is no ONE RIGHT SETTING for either of those I set
them to optimize usability based on band, conditions, et al
Email me direct if your have more related questions. :)
73,
__
Clay Autery, KY5G
(318) 518-1389
On 12/28/19 13:13, kd2fsh wrote:
If
If somebody can help me what are the best settings for Re Level and Scale? I
just move to Arizona from New Jersey and put up an EndFed Antenna.Thank
youJerryKD2FSH201-937-530673Sent from my Verizon, Samsung Galaxy smartphone
__
Elecraft
Hi Don,
I do have the SVGA option installed but do not remember upgrading the K3
for 1 amp. Not sure how I missed that upgrade. So in a few weeks will be
opening up my K3 to check that and if not there putting in the upgrade.
Thanks for your advice.
73, tom w7sua
On 10/28/2019 9:10 PM, Don
Tom,
If you have not yet made the K3 switch to the 1 amp output, that alone
could explain the problem, especially if you have the SVGA option in
your P3. The 0.5 amp source is marginal in the P3 without any options.
73,
Don W3FPR
On 10/28/2019 11:17 PM, Tom Azlin W7SUA wrote:
Thanks Don.
Thanks Don.
I measured the power supply sag at the power supply to be about 0.05
volts. Replaced the cables with larger gauge and still had a problem,
perhaps internal to the K3. Switched to feeding the P3 directly from the
power supply ( an Astron 70, but switch to Alinco 50 amp with same
Tom,
That sounds strange. I would first suggest checking all the Power
Supply to K3, and either K3 AUX DC to P3 or the Power Supply to P3 power
cables for loose connections.
A drop from 14.5 to 14.7 volts down to 12.8 volts indicates a high
resistance power cable or a bad power supply.
Hi. My P3 has started turning off a few seconds to a minute after I turn
on my K3/P3 or when I then try to turn my P3 back on. I was watching and
saw no error message like low voltage. Watching also the voltmeter on my
K3 and stayed at 14.5 to 14.7 volts. dropped power supply to 14 volts
and
: Thursday, October 17, 2019 9:13:42 PM
Subject: Re: [Elecraft] P3 SVGA Question
I suspect that might be a function of the monitor.
Why put a small image of the P3 on a big monitor. Just look at the small P3
image itself.
Sent from my iPhone
...nr4c. bill
> On Oct 17, 2019, at 5:10 PM,
I suspect that might be a function of the monitor.
Why put a small image of the P3 on a big monitor. Just look at the small P3
image itself.
Sent from my iPhone
...nr4c. bill
> On Oct 17, 2019, at 5:10 PM, n...@n1ix.com wrote:
>
> I have a P3 with the SVGA option installed.
>
> Is it
I have a P3 with the SVGA option installed.
Is it possible to display the frequency spectrum in a window rather than
using the entire monitor?
73
Dave N1IX
__
Elecraft mailing list
Home:
Dave,
What are you using to power the P3? Try a good stiff power source - not
a wall-wart.
If the power source cannot provide the current required at the voltage
required, then you will still hear a relay click as the P3 tries to
power up, but the current or voltage from the power source
Hey Dave,
Is the P3's 12v supplied from the 12v aux port (rca Jack)?
If your K3 is a few years old, you might need the K312mdkt.
This boosts current output from .5 to 1.0 amps.
-
73, Russ - W9RB
--
Sent from: http://elecraft.365791.n2.nabble.com/
So on page 38 in the manual, how are the jumpers configured? Mine is set up
with Jumper across 2 and 3. When power is applied, the P3 turns on, but the
power switch can still turn it off or on as long as power is present.
Chuck KE9UW
c-haw...@illinois.edu
Sent from my iPad
> On Sep 7, 2019,
I bought a used P3 from an estate. Unfortunately it doesn't power up.
I am sure that it has 12+ volts and that it is jumpered correctly.
I can hear the relay click when I press the power button.
Anything I may be overlooking? I have actually read and reread the manual.
Dave N1IX
My P3 display freezes momentarily. It’s intermittent, I checked all the
cables.
What does the blinking red light in the box do, don’t remember and can’t find
it in the manual
Ray
W8LYJ.
Sent from my iPad
__
Elecraft mailing list
Thanks for all the inquiries.
Todd, WA7U
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
I have an early K3/100 [#642] and a P3. On 60 m [5358.5] CW, I can see
my signal when I key, at about -90 dBm on both the spectrum display and
the waterfall. This seems to occur only on 60 m, on other bands the P3
display "mutes" on key-down. I just noticed it, don't know if it's
always been
The P3 with SVGA card is sold.
Thanks to all who responded!
73,
- Craig, AE6RR
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
have an Elecraft P3 Panadapter with the SVGA option installed for sale.
It has been connected to my remote station and not turned on most of the
time. Very clean, non-smoking environment.
I can ship it via UPS or it is available for pickup in San Jose.
The P3 with the SVGA option is $1054.90
I have an Elecraft P3 Panadapter with the SVGA option installed for sale.
It has been connected to my remote station and not turned on most of the
time. Very clean, non-smoking environment.
I can ship it via UPS or it is available for pickup in San Jose.
$575 + shipping
PayPal accepted
Kev,
Glad it's working! I'm enough OCD that
after being a few Hz off every so often
and going through the ref cal procedure, I
bought the exref option and a BFG7TBL
GPSDO on fleabay. With this, the K3 & now
K3s is adjusted perfectly at all times and
the computer clock is dead on constantly.
Only to read the scale. Keyed from the rig.
It's working guys! As I mentioned, everything is lining up as expected.
This is why I went with Elecraft. Because of this group. Last group would
have been everything from RTFM to why would you want to do that...
73,
Kev N4TT
On Thu, Jul 25, 2019 at
Kev,
Do you have FlDigi set to produce audio tones in SSB mode for CW or is
it keying the K3 directly?
That will make a significant difference, and the P3 signal placement
will reflect that.
We did not consider that you were using a software application to
produce CW previously to this
Hi Don:
I'm still checking things out but I think I have it all working together. I
calibrated the radio using WWV at 5, 10 and 15 MHz. I only had to line up
one and the other two fell right in. Then I went to the P3 and lined that
up with ref cal. Again, everything lined up at 5, 10 and 15.
Re: choice of test signal for calibrating the P3
> I am not certain why Alan prefers using a BCB signal, but WWV is an AM signal
> with defined frequency and tone frequencies.
Two reasons. The main one is that the local AM station's signal doesn't
depend on propagation. It is always there,
Kev,
I believe that Alan's response, while correct is a bit confusing.
In CW mode, a signal at 7.035,000 kHz should be shown at 7.035,000 MHz.
OTOH, an SSB signal with a suppressed carrier frequency of 7.135,000 MHz
will show the suppressed carrier frequency as the center, but the
intelligence
Just checked my K3S and P3 using WWV 5.0 MHz and 15.0MHz. The error
indicated on the radio is 1 to 2 Hz low. The P3 is correct for both
frequencies with a Ref Cal value of -55 for both frequencies.
My K3S calibration method uses CW mode, with CWT active and press SPOT.
That will zero the
This may be too simplistic or doesn't
address the OP as well as it could but...
I do have an external 10M reference, a
GPSDO and use that to keep the K3s in
proper frequency adjustment. That said,
the instructions in the K3 or K3s manual
address how to zero beat a known frequency
source
I thought an oscilkator was one of those green lizards with lots of teeth
that live in the swamp
On Tue, Jul 23, 2019 at 4:25 PM Nr4c wrote:
> For CW, if radio is set to 7.040 then it will transmit a carrier on 7.040.
> If you tune to a station transmitting on 7.030 then your radio should
For CW, if radio is set to 7.040 then it will transmit a carrier on 7.040. If
you tune to a station transmitting on 7.030 then your radio should also be at
7.039 and the P3 would show a spike on 7.030. The pitch of the audio is done in
the receiver so you can make out the code. Otherwise you
You could be right. I'm out of town right now so I can't check it. But
I think I remember that in some of the digital modes the definition of
VFO A frequency is different.
Alan N1AL
On 2019-07-23 11:36, Joe Subich, W4TV wrote:
> On 2019-07-23 12:47 PM, Alan Bloom wrote:
>
>> Also be aware
Thanks all!
There's a ref cal on the K3s. I ran through the procedure for that using 15
MHz and rechecked on 10 MHz. Seems this was quite a bit off. Now, not only
is it lining up on WWV but also any CW signal I select lines up very
closely between the marker on the P3 and a 600 Hz marker on
On 2019-07-23 12:47 PM, Alan Bloom wrote:
> Also be aware that the center frequency differs depending on mode.
The P3 *should be able to account for that* by using the FI get:
FI * (I.F. Center Frequency; GET only)
RSP format: Fi; where represents the last 4 digits of the
K3’s
Maybe that's the basic question...
If I tune the radio to 7.035 to set a CW signal for a pitch of 600 Hz (as
set using the PITCH function) what should I expect to see on the P3?
1) The P3 shows 7.035 and the CW signal is offset from the center by 600 Hz?
2) The P3 shows 7.035 and compensates
Good advice.
Also be aware that the center frequency differs depending on mode. For
example, it is the supressed carrier frequency on SSB but is offset by
typically 600 Hz on CW.
I like to use AM mode for frequeny calibration. After doing a frequency
calibration on the K3, tune to a signal
First make sure the radio is correct on all WWV frequencies. I use CW mode
and Auto Spot. That will get to within 2 Hz or better. Adjust the Ref freq to
calibrate.
Then you can calibrate the P3 to the radio.
No tuning or listening for zero beat required.
Bob, K4TAX
Sent from my iPhone
Hi Jim:
I thought I had the right adjustment on the P3 but it seems global. I can't
figure out why WWV can be spot on and then another signal off. I can't even
be sure if it is the radio or the P3 (or me) at this point. I'll keep
digging.
Kev
On Tue, Jul 23, 2019 at 3:57 AM Jim Brown wrote:
It's been a while since I looked at the manuals for my K3 and P3, but I
do recall that there are calibration procedures for both.
73, Jim K9YC
On 7/22/2019 9:28 PM, Kevin, N4TT wrote:
I noticed my P3 doesn't seem to be zeroed with the K3s. When I tune in a CW
signal with a 600 Hz pitch the P3
I noticed my P3 doesn't seem to be zeroed with the K3s. When I tune in a CW
signal with a 600 Hz pitch the P3 is off by 71 Hz. Not much but, I
expected - zero.
In AM - WWV at 5 MHz the P3 seems spot on.
73,
Kev N4TT
__
Elecraft mailing
Alan: Your description may be right on, it may explain why the effect is
difficult to reproduce and appears to be "intermittent," sometimes it
maintains the center frequency and sometimes it doesn't. I'll try the
FixMode=Static with a controlled set of changes that I know will cause
the
m
> that the P3 is operating correctly.
> 73 Tom
> Va2fsq.com
>
> -Original Message-
> From: elecraft-boun...@mailman.qth.net On
> Behalf Of Fred Jensen
> Sent: July 21, 2019 8:04 PM
> To: elecraft@mailman.qth.net
> Subject: Re: [Elecraft] P3 center
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Fred Jensen
Sent: July 21, 2019 8:04 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 center frequency
Not sure who I'm talking to here, no signature, no call. It's a little hard to
explain but ...
Assume
0 PM, Tom wrote:
Hi,
What exactly do you mean?
It is always set to whatever you send. If you explain this a little
more perhaps I can help.
73
-Original Message-
From: elecraft-boun...@mailman.qth.net
On Behalf Of Randy Farmer
Sent: July 21, 2019 2:44 PM
To: elecraft@mailman.qth.net
Su
to whatever you send. If you explain this a little more
perhaps I can help.
73
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Randy Farmer
Sent: July 21, 2019 2:44 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 center frequency
It's been brou
: [Elecraft] P3 center frequency
It's been brought up several times in the last two or three years. No response
from the P3 software guys. It's EXTREMELY annoying that the P3 won't respect
the center frequency setting if the radio is tuned via any CAT command. I've
given up on hoping it will ever
P3 in perfect working condition
P3TXMON transmit monitor with 2Kw HF directional coupler (or 200W VHF
one)
P3SVGA video adapter for VGA
CBLP3Y RJ45 cable for K3s/KIO3B
Value (1022.90 + 289.95) = 1,312.85
For sale less than 50% $650 plus shipping
Raj, N2RD
--
Raj Dewan, N2RD
It's been brought up several times in the last two or three years. No
response from the P3 software guys. It's EXTREMELY annoying that the P3
won't respect the center frequency setting if the radio is tuned via any
CAT command. I've given up on hoping it will ever be fixed. My guess is
that
Jim: In general, yes, if you change bands with BAND ^/v. When you
change bands via the CAT, the P3 center freq won't always end up where
you last had it. I believe SPAN width is preserved but the span limits
show up strange. It's a known issue, has been discussed at some length
here a few
Should the P3 center frequency and span be remembered when changing bands?
Rephrasing, can they be remembered when changing bands?
Jim N7US
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
P3 Panadapter. Comes with cblp3y cable to interface with the K3S and cables
for the K3. $599 plus shipping. PayPal and certified checks accepted, US
sales only. Lou, W0FK
-
St. Louis, MO
"The difference between stupidity and genius is that
genius has its limits." Albert Einstein
The P3 SVGA USB connector is intended for a keyboard or memory stick,
which are low-power devices. For that reason, the current is limited to
a single unit load = 100 mA (x 5V = 1/2 watt).
Alan N1AL
On 7/2/19 9:00 AM, w4sc wrote:
Looking for the specified current that can be supplied
P3 Panadapter. Comes with cblp3y cable to interface with the K3S and cables
for the K3. $599 plus shipping.
P3TXMON P3 transmit monitor/DCHF-2000 1.8-54 MHz, 1- 2000W coupler. $175
plus shipping.
Buy both for $775, shipping included 50 States.
PayPal and certified checks accepted, US sales
Looking for the specified current that can be supplied through the keyboard USB
connector. USB2.0 spec says 500ma. What current (ma) is available from P3?
Is it limited to a lower value through a current monitor / switch?
Sent from Mail for Windows 10
P3 Panadapter. Comes with cblp3y cable to interface with the K3S and cables
for the K3. $599 plus shipping.
P3SVGA P3 Video/FFT Adapter for $245, includes shipping to 50 States..
P3TXMON P3 transmit monitor/DCHF-2000 1.8-54 MHz, 1- 2000W coupler. $175
plus shipping.
Buy all 3 for $999,
Win4K3Suite macros will work with the K3, P3, and KPA500/1500, even in the same
macro, I think.
Jim N7US
-Original Message-
Do you also have access to the P3 controls remotely via the RS-232 port? My P3
loses its span end-point settings if I change the band via CAT commands and I
201 - 300 of 4853 matches
Mail list logo
