: [Elecraft] P3 center frequency
It's been brought up several times in the last two or three years. No response
from the P3 software guys. It's EXTREMELY annoying that the P3 won't respect
the center frequency setting if the radio is tuned via any CAT command. I've
given up on ho
P3 in perfect working condition
P3TXMON transmit monitor with 2Kw HF directional coupler (or 200W VHF
one)
P3SVGA video adapter for VGA
CBLP3Y RJ45 cable for K3s/KIO3B
Value (1022.90 + 289.95) = 1,312.85
For sale less than 50% $650 plus shipping
Raj, N2RD
--
Raj Dewan, N2RD
rdew...@rochester.
It's been brought up several times in the last two or three years. No
response from the P3 software guys. It's EXTREMELY annoying that the P3
won't respect the center frequency setting if the radio is tuned via any
CAT command. I've given up on hoping it will ever be fixed. My guess is
that it'
Jim: In general, yes, if you change bands with BAND ^/v. When you
change bands via the CAT, the P3 center freq won't always end up where
you last had it. I believe SPAN width is preserved but the span limits
show up strange. It's a known issue, has been discussed at some length
here a few m
Should the P3 center frequency and span be remembered when changing bands?
Rephrasing, can they be remembered when changing bands?
Jim N7US
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http:
P3 Panadapter. Comes with cblp3y cable to interface with the K3S and cables
for the K3. $599 plus shipping. PayPal and certified checks accepted, US
sales only. Lou, W0FK
-
St. Louis, MO
"The difference between stupidity and genius is that
genius has its limits." Albert Einstein
-
The P3 SVGA USB connector is intended for a keyboard or memory stick,
which are low-power devices. For that reason, the current is limited to
a single unit load = 100 mA (x 5V = 1/2 watt).
Alan N1AL
On 7/2/19 9:00 AM, w4sc wrote:
Looking for the specified current that can be supplied throug
P3 Panadapter. Comes with cblp3y cable to interface with the K3S and cables
for the K3. $599 plus shipping.
P3TXMON P3 transmit monitor/DCHF-2000 1.8-54 MHz, 1- 2000W coupler. $175
plus shipping.
Buy both for $775, shipping included 50 States.
PayPal and certified checks accepted, US sales
Looking for the specified current that can be supplied through the keyboard USB
connector. USB2.0 spec says 500ma. What current (ma) is available from P3?
Is it limited to a lower value through a current monitor / switch?
Sent from Mail for Windows 10
P3 Panadapter. Comes with cblp3y cable to interface with the K3S and cables
for the K3. $599 plus shipping.
P3SVGA P3 Video/FFT Adapter for $245, includes shipping to 50 States..
P3TXMON P3 transmit monitor/DCHF-2000 1.8-54 MHz, 1- 2000W coupler. $175
plus shipping.
Buy all 3 for $999, sh
Win4K3Suite macros will work with the K3, P3, and KPA500/1500, even in the same
macro, I think.
Jim N7US
-Original Message-
Do you also have access to the P3 controls remotely via the RS-232 port? My P3
loses its span end-point settings if I change the band via CAT commands and I
wou
Do you also have access to the P3 controls remotely via the RS-232
port? My P3 loses its span end-point settings if I change the band via
CAT commands and I would have no way to reset them remotely.
A secondary problem we encountered at W7RN with web cams is that they
have a tendency to gobbl
I have long been using my K3 remotely and I have wished for a simple way to
view my P3 via remote.
I just found a solution that is working nicely.
I bought a $20 Wyze Cam 2 which is a 2.4 Ghz webcam with an app for my phone.
The Wyze cam will focus closely on the P3 giving me a full screen disp
Jim,
Refer to your Icom CT-9100 manual.
First thing to be determined is -- does it have an IF output?
If so, the 2nd thing to determine is -- What is the IF output frequency?
The P3 can be tuned to use an IF output between 455kHz and 21MHz.
If there is no IF output, then you would have to add o
Has anyone added a P3 Panadapter to an ICOM CI-9100 transceiver? If so, are
there any reasonably detailed instruction available to mod up the IC-9100 to
accommodate the P3? I am new to amateur radio and not an engineer but have
a modest level of skill with a soldering station.
Thanks in advan
On 6/23/2019 5:53 AM, Mark Wheeler via Elecraft wrote:
I've recently noticed that I have almost no waterfall displaying on my
24" monitor which makes using the SVGA feature almost useless. I
thought maybe it was because of poor band conditions, but now I'm
wondering if there is something that
I've recently noticed that I have almost no waterfall displaying on my 24" monitor
which makes using the SVGA feature almost useless. I thought maybe it was because of
poor band conditions, but now I'm wondering if there is something that needs to be
adjusted... I used to have a near exact
Subject: [Elecraft] P3 Display Flashing
Just setting up for field day and my P3 has developed a problem. About 5
seconds after startup the spectrum box clears and redraws about once a
second. While it is blank the text "5 ms / div" appears in the lower left
corner outside of the waterfall
Just setting up for field day and my P3 has developed a problem. About 5
seconds after startup the spectrum box clears and redraws about once a
second. While it is blank the text "5 ms / div" appears in the lower left
corner outside of the waterfall box.
Any ideas?
Glenn KD0Q
___
ob McGraw K4TAX
Sent: Saturday, June 08, 2019 5:57 PM
To: Elecraft Reflector
Subject: [Elecraft] P3 Noise band
I noticed when working the 6M contest today, I observed a band of noise on my
P3. It always tracks above the frequency about 20kHz at the lower edge. The
width of the band of noise
I noticed when working the 6M contest today, I observed a band of noise
on my P3. It always tracks above the frequency about 20kHz at the
lower edge. The width of the band of noise is about 35 kHz. As I
tune, the band of noise stays relative to the tuned frequency, thus
moving up or down
the house - trust
me it makes a difference!
Hank
K4HYJ
- Original Message -
From: Dave Cole (NK7Z) (d...@nk7z.net)
Date: 05/21/19 11:30
To: Elecraft Reflector (elecraft@mailman.qth.net)
Subject: [Elecraft] P3: Removing the plastic display cover
Hello,
I have a bit of dust behind the plast
.@nk7z.net)
Date: 05/21/19 11:30
To: Elecraft Reflector (elecraft@mailman.qth.net)
Subject: [Elecraft] P3: Removing the plastic display cover
Hello,
I have a bit of dust behind the plastic display cover on my P3, between
the case and the cover.
In reviewing the kit assembly instructions, it looks
Hello,
I have a bit of dust behind the plastic display cover on my P3, between
the case and the cover.
In reviewing the kit assembly instructions, it looks as if the four
screws on the four corners of the plastic display cover are also used to
hold the entire display board in place on the fr
Hi Robin,
Make sure you have the P3 and K3 connected via the 9 pin RS232 cable, and that
both are at the same baud rate mentioned the manual.
Also, in the P3 menu there is an entry for radio type. Select K3 if it is not
already entered.
73,
Eric
/elecraft.com/
On 4/18/2019 7:32 AM, oz6...
Great suggestion... why didn't I think of that???
73,
Bill
K9YEQ
https://wrj-tech.com/
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Alan
Sent: Wednesday, April 17, 2019 11:17 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 sensor questions
H
Behalf Of oz6...@qsl.net
Sent: Thursday, April 18, 2019 4:33 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] P3 Display issues...
Hi -
I just cannot get this to work for me. I am looking at my P3 connected to a
K3. It is connected between the IF In on the P3 and IF Out on the K3. When
Robin,
Do you have an RS-232 9 pin cable connected between the K3 RS232
connector and the XCVR connector on the K3? That cable is what carries
the frequency and other information to the P3.
For computer connection, connect the PC to the "PC" connector on the P3.
If you have a K3S and are op
Hi -
I just cannot get this to work for me. I am looking at my P3 connected to a K3.
It is connected between the IF In on the P3 and IF Out on the K3. When looking
at the P3 display, on all frequencies, I do not see the actual frequency of the
VFO, I see 0, for example to top line has -25.0
Hi -
I must be a complete idiot, but I just cannot get this to work for me. I am
looking at my P3 connected to a K3. It is connected between the IF In on the P3
and IF Out on the K3. When looking at the P3 display, on all frequencies, I do
not see the actual frequency of the VFO, I see 0, f
Is there a way to make the power meter in the P3 auto scale like the W2 does?
Thank you
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.
Here's what I use. It allows switching up to four sensors to one P3:
https://smile.amazon.com/gp/product/B00AUB3SSA/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1
Amazon says it is "currently unavailable" but if you search for "8p8C
manual switch" you should be able to find other options.
Yo
Having become the proud father of a KPA1500, I am enjoying it a lot. I use a
160M Full Wave Loop on Ant 1 and my Sommer log fed yagi on Ant 2. I only
have one 2KW HF Sensor for my P-3 and currently have it hooked up to Ant2. I
would love to also have one hooked up to Ant 1, but the P3 has only
On 4/15/19 6:37 PM, Ed gilliland wrote:
I am unable to put the P3 in "Fixed Tune Mode", the display remains
constant and the VFO A cursor moves across the display.
I think that's the way it's supposed to work in fixed-tune mode. The
display stays at the same frequency and the VFO moves across
My guess would be that you don't have it connected to the K3 serial port
correctly. If it isn't getting frequency information, it has to stay in
scrolling mode.
73,
/Rick N6XI
--
Rick Tavan
Truckee, CA
On Mon, Apr 15, 2019 at 6:37 PM Ed gilliland wrote:
> I am unable to put the P3 in "Fixed
I am unable to put the P3 in "Fixed Tune Mode", the display remains
constant and the VFO A cursor moves across the display.
I'm sure that I have something configured incorrectly but haven't been
able to discover the error. I have a RS232 cable from the P3 PC port
and a RS232 port on the PC an
When I set the noise level with Ref Lvl to the bottom of the spectrum
display, It will over time continue to move downward until the noise level
is off the spectrum display. If I cycle the P3, the noise level is well
above the bottom of the display and the waterfall shows the noise which
comes wit
Just remember to place the switch in the on position if you do.
- pjd
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Nr4c
Sent: Wednesday, March 27, 2019 7:05 PM
To: Rich
Cc: Elecraft
Subject: Re: [Elecraft] P3 IF Output
I believe that’s what it was put
I believe that’s what it was put there for.
Sent from my iPhone
...nr4c. bill
> On Mar 27, 2019, at 4:59 PM, Rich wrote:
>
> I have been running an SDR via the IF out of the K3. I now have a P3, can
> use the IF out of the P3 and send that to an SDR?
>
> I have no idea why I would even wa
I have been running an SDR via the IF out of the K3. I now have a P3,
can use the IF out of the P3 and send that to an SDR?
I have no idea why I would even want to do that but I am curious if that
will work.
Rich
K3RWN
__
Elecraf
Mine says Cat 5e on it and it. pinned out the same as an Ethernet LAN cable
So I will say Yes
On Friday, March 15, 2019, 6:15:56 PM EDT, Raymond
wrote:
Is the cable between the sensor and P3 a standard cat 5 cable?
Ray
W8LYJ
Sent from my iPhone
__
Is it possible the manual has a pin-out?
Sent from my iPhone
...nr4c. bill
> On Mar 15, 2019, at 6:14 PM, Raymond wrote:
>
> Is the cable between the sensor and P3 a standard cat 5 cable?
> Ray
> W8LYJ
>
> Sent from my iPhone
> __
>
Is the cable between the sensor and P3 a standard cat 5 cable?
Ray
W8LYJ
Sent from my iPhone
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mail
My PX3 has all of the same problems. (including the REF issue which
includes non-whole number values)
I will try the save/reset/restore hack later.
Even if this solves the issues, what's to prevent them from returning?
73, Bruce W2SE
On 3/11/19 09:32, Dave Cole (NK7Z) wrote:
Thanks f
Thanks for the info sir!
73s and thanks,
Dave (NK7Z)
https://www.nk7z.net
Award Manager, 30MDG Grid Awards
ARRL Technical Specialist
ARRL Volunteer Examiner
ARRL OOC for Oregon
On 3/10/19 12:01 PM, Victor Rosenthal 4X6GP wrote:
No, the save/restore restored everything to how it was before.
73
No, the save/restore restored everything to how it was before.
73,
Victor, 4X6GP
Rehovot, Israel
Formerly K2VCO
CWops no. 5
http://www.qsl.net/k2vco/
On 10 Mar 2019 20:57, Dave Cole (NK7Z) wrote:
I have been thinking of that. When you did it, was your P3 revocered to
the same exact setup as wh
I have been thinking of that. When you did it, was your P3 revocered to
the same exact setup as when you saved the config file? Did you have to
resetup anything else?
73s and thanks,
Dave (NK7Z)
https://www.nk7z.net
Award Manager, 30MDG Grid Awards
ARRL Technical Specialist
ARRL Volunteer Exa
I've never had any trouble with REF LEVEL, but it can't hurt to try the
save / reset / restore routine and see if it helps.
73,
Victor, 4X6GP
Rehovot, Israel
Formerly K2VCO
CWops no. 5
http://www.qsl.net/k2vco/
On 10/03/2019 18:14, Dave Cole (NK7Z) wrote:
I am seeing something similar to this
I am seeing something similar to this as well... Not in SPAN, but in
REF LVL. I set REF LVL while on 30 Meters, and leave the band.
Ssometimes when I return to 30, I need to touch the REF LVL level to get
it to return...
By touch, I mean I select REF LVL, then just turn the knob ever so
sli
I had a problem in which both SPAN and CENTER changed arbitrarily (it
seemed) on band changes. I finally saved the configuration using the P3
Utility, reset the P3 to factory parameters (power off, hold LABELS
while powering on, wait for 2 seconds, let go of LABELS), and finally
used the utility t
Various searches dredged up nothing helpful. I recently developed a P3
problem. The SPAN does not get saved. Whenever I change bands to a band I had
set it, say, to 50 kHz, the SPAN resets itself to 5 kHz. Sometimes I can even
watch the display as it cranks down the bandwidth.
This is a P3
In the past few months, my P3 has begun to intermittently forget its
SPAN and CENTER values (it is always in fixed mode).
It doesn't seem to be related to any changes in firmware in either my K3
or P3, which I haven't done in some time.
I use the DXLAB software, in case that could have someth
Does the P3 have (or are there plans to add) support for a USB hub on the P3?
This would be very handy for those who want to have a Keypad and a Keyboard
connected to the P3.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/
Yes, the P3 automatically bypasses its internal preamp whenever the
input signal level overloads the ADC. It uses a fairly complicated
algorithm to try to minimize the inconvenience. The first time the ADC
overloads, the preamp is switched out for a fairly short period of time
and then it is
Hello,
since I worked on 80 and 160 m the last couple of weeks I noticed that the
P3 panadapter starts clicking relays whenever a very strong local signal
(-10 dBm to 0 dBm) or a number of strong signals within the bandpass are
present. I could not find a relation yet when it happens because it t
Re: "It is as it just fell off!"
It probably did. It is likely the surface mount joints were solder starved
during original board processing. They can sometimes make surprisingly good
electrical contact, at least in low current applications. Without a careful
close examination with a good l
I was wondering as I think there have been two of these now... Thanks
for the update!
73s and thanks,
Dave (NK7Z)
https://www.nk7z.net
Award Manager, 30MDG Grid Contest
ARRL Technical Specialist
ARRL Volunteer Examiner
ARRL OOC for Oregon
On 1/3/19 8:33 AM, David Olean wrote:
Hello Dave,
"W
Hello Dave,
"Why?" is the big question. I have no idea why it fell off. There is
nothing that sticks out to invite damage. That RJ-11 receptacle is
hidden underneath the P3. There are six surface mount solder connections
to the board, and there are two small metal inserts in the plastic
hous
We now know "what" is falling off, the next question is why is a part
dropping off?
I must have missed that, can someone refresh my memory please?
73s and thanks,
Dave (NK7Z)
https://www.nk7z.net
Award Manager, 30MDG Grid Contest
ARRL Technical Specialist
ARRL Volunteer Examiner
ARRL OOC for Or
David:
I experienced the same thing when I bought an otherwise good condition P3 used.
Elecraft can provide you with the replacement part no.
I’ve never gotten around to fixing mine (otherwise works great).
Bob Brown, N1CVX
Sent from my iPad
__
David,
That jack is used only for factory testing. Your P3 should work
normally without it.
Hang onto the jack and if you ever send the P3 to Elecraft for repair,
include it and the P3 will come back with it installed.
73,
Don W3FPR
On 1/2/2019 4:06 PM, David Olean wrote:
I went up to my re
I went up to my remote ham shack to take out the ham gear for the
winter, and turn off the heat. I had a K3 with P3 panadaptor there for
my ten meter station, and when I started disconnecting things, I heard
something rattling around inside the P3. (?) When I got home and opened
it up I found
I may have some wear on my encoder button
in the P3. The encoder itself seems fine,
when I rotate it, it performs perfectly.
When I push on it, often the marker does
not move or, it moves the frequency part
way. If I hold the knob and apply a little
downward pressure when pushing it usually
re-appear on the other side.
Pretty interesting effect, but perfectly logical, once you understand
what is being done 'under the covers' to prevent you hearing that birdie
in your receiver.
73,
-- Dave, N8SBE
Original Message ----
Subject: Re: [Elecraft] P3 Phantom Signal
I have the same on my P3.
I guess the phantom signals come from synthesizer spurious. When K3 VFO tunes
to the phantom signal by turning VFO nob, you will hear its carrier.
My K3 is not K3s but old one with original synthesizer. I am not sure on K3s or
K3 with new synthesizer.
73 de JH3SIF, Kei
Make sure your BNC cable between the K3's IF output and the P3 input is
securely plugged in. (I usually unplug and replug in the cable as part of this
test.) If you have an alternate BNC cable, try it too as its always possible
there is a poor connection between the cable shield and one of the
I've noticed a large number of "phantom" signals on the P3. They look like
signals but when I turn the RX dial, they move along with the cursor. When I
turned the P3 off and then on, they went away of 40m but that same thing
didn't happen on 15m. Any ideas?
73, Ken, K6LA / VY2TT
The SVGA option will let you have a large screen on your P3.
73 Bill AE6JV
On 11/22/18 at 12:12 PM, d_hud...@outlook.com (Douglas Hudson) wrote:
> The eye appeal of the P3 sitting beside the transceiver is
> hard to beat but, with the P3, the size of the display is fixed where with a
> play
>
om: elecraft-boun...@mailman.qth.net on
behalf of Bill Weaver
Sent: Wednesday, November 21, 2018 10:17:12 AM
To: elecraft
Subject: [Elecraft] P3 v. SDRPlay RSP1A for panadapter
I'm about to place an order for a K-Line and have a question for the
experienced users out there. What is the advantage of
ting
desk and computer.
73,
Barry
K3NDM
-- Original Message --
From: "Dave Scarfe"
To: "Barry LaZar"
Cc: "Bill Weaver" ; Elecraft@mailman.qth.net
Sent: 11/22/2018 8:54:00 AM
Subject: Re: [Elecraft] P3 v. SDRPlay RSP1A for panadapter
I don't have P3, b
e will
> dictate what bandwidth you will use and when.
>
> 73,
> Barry
> K3NDM
>
> -- Original Message --
> From: "Bill Weaver"
> To: "elecraft"
> Sent: 11/21/2018 1:17:12 PM
> Subject: [Elecraft] P3 v. SDRPlay RSP1A for panadapter
>
> &g
ually run about 50 KHz on my 24" monitor. This way
I can see where the DX station is hearing. The way you operate will
dictate what bandwidth you will use and when.
73,
Barry
K3NDM
-- Original Message --
From: "Bill Weaver"
To: "elecraft"
Sent: 11/21/2018 1:1
The P3 is simpler- plug and play, no fooling around with configuring HDSDR
or whatever software you prefer. You can set up the hardware buttons for
whatever you want, so it’s very convenient to make quick changes to span,
etc.
SDRPlay is cheaper and can integrate with other software to show spots
I'm about to place an order for a K-Line and have a question for the
experienced users out there. What is the advantage of the P3 v. The SDRPlay box
as a panadapter if any?
Thanks
Bill - WE5P
__
Elecraft mailing l
It happens with two different OSs and two different programs.
The best place to look first is the common elements.
73 Bill AE6JV
On 10/26/18 at 5:00 PM, ghyoung...@gmail.com (Grant Youngman) wrote:
Why do you presume it is a fault of the P3 and not something
funky happening with whatever soft
Why do you presume it is a fault of the P3 and not something funky happening
with whatever software you’re running on your PC?
Grant NQ5T
K3 #2091 KX3 #8342
> On Oct 26, 2018, at 7:46 PM, Bill Frantz wrote:
>
> I have the same problem with wsjt-x running from a Mac. When I change bands,
> the
I have the same problem with wsjt-x running from a Mac. When I
change bands, the center frequency changes. Very annoying since
it moves part of the display outside of the 17M and 12M bands.
73 Bill AE6JV
On 10/26/18 at 2:47 PM, k6...@foothill.net (Fred Jensen) wrote:
I think that may be a clu
t first but after further
inspection I was wrong. (as Usual)
Ed..AB4IQ
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of AB4IQ
Sent: Friday, October 26, 2018 4:13 PM
To: 'Fred Jensen' ; elecraft@mailman.qth.net
Subj
red Jensen' ; elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3: Span limits move when changing bands
I guess maybe I need to fire up N1MM+ to see what happens here. Dxbase
seems to work fine and so does DX4WIN.
Ed.. AB4IQ
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailt
I believe I heard of this "problem" before. It needs to be addressed
with the N1MM+ folks for a possible fix.
73,
Don W3FPR
On 10/26/2018 4:52 PM, Fred Jensen wrote:
It may be a timing issue. It only happens when the software [N1MM+ in
my case] sends a frequency command. It rarely happens f
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3: Span limits move when changing bands
It may be a timing issue. It only happens when the software [N1MM+ in my case]
sends a frequency command. It rarely happens for me when I make the first
frequency change. Returning to the first band
It may be a timing issue. It only happens when the software [N1MM+ in
my case] sends a frequency command. It rarely happens for me when I
make the first frequency change. Returning to the first band, it
usually happens. And you're right, it is annoying.
73,
Fred ["Skip"] K6DGW
Sparks NV D
lecraft-boun...@mailman.qth.net] On Behalf Of K9MA
Sent: Friday, October 26, 2018 1:12 PM
To: w...@tx.rr.com
Cc: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3: Span limits move when changing bands
I haven't noticed that large a shift, but sometimes 0.5 kHz or so.
Scott K9MA
I haven't noticed that large a shift, but sometimes 0.5 kHz or so.
Scott K9MA
--
Scott Ellington
--- via iPad
> On Oct 26, 2018, at 8:01 PM, Randy Farmer wrote:
>
> First sent this to Skip rather than the list...
>
>> This appears to have been a problem from the time of the introd
First sent this to Skip rather than the list...
This appears to have been a problem from the time of the introduction
of the P3. It seems to be triggered when a frequency command is issued
to the radio via the P3 comm port. Is there any hope on the horizon
for curing this extremely annoying "f
Message: 10
Date: Mon, 15 Oct 2018 09:21:36 -0700 (MST)
From: n6hz
To:elecraft@mailman.qth.net
Subject: Re: [Elecraft] Elecraft P3 Bar Cursor
Message-ID:<1539620496239-0.p...@n2.nabble.com>
Content-Type: text/plain; charset=UTF-8
Hi Ed,
Are there magenta and green arrows toward the bot
Hi Ed,
Are there magenta and green arrows toward the bottom of the spectrum
display? These indicate where the cursors are relative to your current
center frequency. If you are in fixed tune mode, you can easily re-center
your VFO A cursor by two consecutive long presses of the SPAN/CENTER but
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: ht
On the P3 on CW the signals seem always lower than on my Elecraft K3S (even
2 S-unit).
This morning I tested the P3 S-meter with my HP8640 signal generator and I
found that on every band the 50uV signal result in a perfect S9 on both K3S
and P3.
Now I think the real question is to introduce a corr
My P3 cursors have disappeared. The menu selections are there but the
cursors do not appear when selected. I have the latest P3 firmware loaded.
Ed W5TM
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
I sent Doug an email about my P3 that is available
P3, P3SVGA and TXMON (2000W) for $800
Jim - W4RKS
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecra
Thanks Martin.
Just wondering if it is normal. From the reports, it is.
Thanks to all.
Bob, K4TAX
Sent from my iPhone
> On Sep 25, 2018, at 10:21 PM, Martin Sole wrote:
>
> Mine does this. The white screen has gone though by the time my finger comes
> off the K3 power button, replaced
Mine does this. The white screen has gone though by the time my finger
comes off the K3 power button, replaced with a P3 boot loader message,
that's also gone very quickly.
Martin, HS0ZED
On 26/09/2018 07:15, Bob McGraw K4TAX wrote:
Just purchased a NIB P3 for my K3S station. Love it!
Que
Just purchased a NIB P3 for my K3S station. Love it!
Question - is it normal for it to initially power on with a bright white
screen while it loads? This is very brief, but sure makes a flash. If
normal, then so be it. It is powered from the DC jack on the K3S. I
always switch the stat
The P3-F panadaptor s/n 2191 has been sold.
Thanks for all the inquiries!
73,
Gene N9SW
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailma
To use the P3 with the K2, you have to modify the K2 to add an IF output
connector. Clifton Labs used to sell an adapter kit which is now
offered by DX Engineering.
https://www.dxengineering.com/parts/dxe-z1k2-kit
The P3 does work fine with the K2, but you don't get all the features
that
f Don Wilhelm
Sent: Tuesday, September 18, 2018 10:13 AM
To: Don Schroder ; elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 Panadapter
Don,
You can use it with the K3 (the P3 input can be tuned anywhere between 455kHz
and 21 MHz).
You will have to add an IF output to the K2. DX Engineering i
s/n 7818 that is about 2/3rds complete. I’m a newbie and this is my
first radio. I’ve been looking at additions for my non-existent ham shack and am
curious about the Elecraft P3. Looking at the advertising, I see it is for the K3
& K3s, and other radios.
Hence, my question. How many of you con
unit.
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Don Wilhelm
Sent: Tuesday, September 18, 2018 10:13 AM
To: Don Schroder ; elecraft@mailman.qth.net
Subject: Re: [Elecraft] P3 Panadapter
Don,
You can use it with the K3 (the P3 input can be tuned anywhere between 4
ng at additions for my non-existent ham shack and am
curious about the Elecraft P3. Looking at the advertising, I see it is for the K3
& K3s, and other radios.
Hence, my question. How many of you consider the P3 to be a must have, and can
it be used with a K2 transceiver? As a side note, w
301 - 400 of 4878 matches
Mail list logo
