*Hello Everyone,*
I'm new with Kannel SMS Gateway.
I have configured Bearerbox, SMSBox and SQLBox for sending bulk sms through
my HTTP Application. But problem is that the speed of sending sms is too
low.
So my first question is that how to increase the speed of sending sms.
Second one is what
Hi
Sms throughput depends on what your carrier/smsc allows you to send.
In smpp smsc it is usually limited by what you contract with your carrier
and can go from 1 sms/sec to 10 or more sms/sec.
with modems (smsc-at), you are limited by the protocol itself, available
radio channels, signal
Hi Group,
I'm newbie in Kannel SMS Gateway. I'm configuring both boxes WAPBox and
SMSBox in Kannel configuration. But I have some confusion in working of
WAPBox in Kannel.
What is main purpose of WAPBox with SMSBox?
Please suggest me that how to use WAP Gateway in SMS Gateway and what
Am 18.09.2013 12:34, schrieb Stuart Eoghan:
We are looking to deploy a new WAP Gateway in our network, to replace
the existing one which is falling over regularly.
Hi Stuart,
please let me answer you questions inlined below:
I have a few questions:
Is the WAP Kannel gateway in use
Hi,
We are looking to deploy a new WAP Gateway in our network, to replace the
existing one which is falling over regularly.
I have a few questions:
Is the WAP Kannel gateway in use commercially in many networks?
Does it support all of or most of the last WAP protocol?
Would it be capable
Am 04.06.2011 21:09, schrieb mattias:
So the gateway are only for old dialup on mobile phones
Not for modern gprs?
the normal Kannel WAP gateway provides the WAP 1.2.1 stack (including WAP Push),
which uses UDP as IP bearer and can be utilized via CSD or GPRS. In fact the
underlying radio
So the gateway are only for old dialup on mobile phones
Not for modern gprs?
The wireless session protocol can be used on any ip network. Including
gprs/umts/hsdpa.
== Rene
-Original Message-
From: users-boun...@kannel.org [mailto:users-boun...@kannel.org] On Behalf
Of mattias
Sent: Saturday, 04 June, 2011 21:09
To: users@kannel.org
Subject: The wap gateway
So
The settings for gprs are similar to the ones that you use for dial-up.
Your mobile operator charges you for any data traffic. But usually gprs is a
lot cheaper than CSD (dial-up).
Just enter the ip address of your Kannel instance in your WAP gateway
settings.
I think that should do the trick
Sent: Sunday, June 05, 2011 12:22 AM
Subject: RE: The wap gateway
The settings for gprs are similar to the ones that you use for dial-up.
Your mobile operator charges you for any data traffic. But usually gprs is
a
lot cheaper than CSD (dial-up).
Just enter the ip address of your Kannel instance
Yes, wapbox is good only for wap 1.x traffic which is for older mobiles. For
wap 2.x traffic you can use squid or any other HTTP proxy.
BR,
Nikos
- Original Message -
From: mattias m...@mjw.se
To: users@kannel.org
Sent: Saturday, June 04, 2011 10:09 PM
Subject: The wap gateway
So
Hi,
I am using the following URL :
http://localhost:1300/kannel:alive it is not working . It shows me that
Unknown command `/kannel:alive'.
Possible commands are:
status
store-status
log-level
shutdown
suspend
isolate
resume
restart
flush-dlr
stop-smsc
start-smsc
add-smsc
remove-smsc
Hi Harmeet,
using http://localhost:1300/stauts?password=password you can check the
status of kannel and wap and other things and you can use below Possible
commands other then these command you can not specify any other
commands. for more info read kannel user guide.
status
store-status
Hi,
Please refer to the kannel CVS userguide , There is mention that :
Checking whether the WAP gateway is alive
You can check whether the WAP gateway (both the bearerbox and the wapbox) is
alive by fetching the
URL kannel:alive.
at page no 33 . Please help me to know how to implement
Message -
From: Harmeet harmeet.dhin...@kochar.com
To: users@kannel.org
Sent: Wednesday, June 30, 2010 1:59 PM
Subject: Checking whether the WAP gateway is alive
Hi,
I am using the following URL :
http://localhost:1300/kannel:alive it is not working . It shows me that
Unknown command
Hello all,
We released version 1.0.2 of Java API for Kannel SMS/WAP gateway.
The latest version introduces prioritized WAP Push functionality and bulk
WAP Push messaging.
For more information visit our blog http://javacodegeeks.blogspot.com/
The upcoming version will introduce, scheduled
Hello all,
We released version 1.0.1 of Java API for Kannel SMS/WAP gateway.
In the latest version a bug is fixed concerning the GSM encoding of SMS
messages. Now messages are properly encoded and send to the SMSC for all
available encodings (GSM, UTF-8, UCS2)
The latest version also introduces
Nope. Kannel is a wap 1.x gateway, not a wap 2.x. It doesn't listen to tcp
80 for traffic. You can use squid for that.
BR,
Nikos
- Original Message -
From: Jefri Abdullah m...@jefri.web.id
To: users@kannel.org
Sent: Wednesday, April 07, 2010 4:21 AM
Subject: Wap gateway using HTTP
Hi, I try to using kannel as wap gateway on my environment, I found
that kannel only using wap protocol stack. Is it possible to use
kannel if client sending regular HTTP request to kannel? I attached
capture from client request.
Best Regards,
Jefri Abdullah
--
NULL
attachment: wpg.jpg
, 2009 at 12:32 PM, Kao. Josh (GSM) josh_...@compalcomm.comwrote:
Dear Nikos,
Is it different behavior to connect to wap gateway between GSM and CDMA
phone? I forgot mention that my cell phone is CDMA phone.
I used to connect to nowsms successfully, but nowsms is a commercial
software, so I
Dear Nikos,
Is it different behavior to connect to wap gateway between GSM and CDMA
phone? I forgot mention that my cell phone is CDMA phone.
I used to connect to nowsms successfully, but nowsms is a commercial
software, so I want to try kannel.
I check my firewall again and the tcp
them meet together?
Best Regards,
Josh
From: Nikos Balkanas [mailto:nbalka...@gmail.com]
Sent: Thursday, February 05, 2009 6:36 PM
To: Kao. Josh (GSM); us...@vm1.kannel.org
Subject: Re: Can't find a port to receive link request in wap gateway
Hi Kao
: Kao. Josh (GSM)
To: Nikos Balkanas ; users@kannel.org
Sent: Wednesday, February 04, 2009 4:45 AM
Subject: RE: Can't find a port to receive link request in wap gateway
Dear Nikos,
Thanks for you suggestion!
I’ve put password in my original kannel.conf, I am sorry that I
: Tuesday, February 03, 2009 7:43 AM
Subject: Can't find a port to receive link request in wap gateway
Dear all,
I am trying setup Kannel to be a wap gateway for a long time, but I always
have a problem when wap browser connects to Kannel. I find there doesn’t have a
port to receive
Balkanas [mailto:nbalka...@gmail.com]
Sent: Tuesday, February 03, 2009 9:23 PM
To: Kao. Josh (GSM); us...@vm1.kannel.org
Subject: Re: Can't find a port to receive link request in wap gateway
Try pgrep -fl bearerbox. You shouldn't see anything running.
Look at bearerbox.log to find the reason
Dear all,
I am trying setup Kannel to be a wap gateway for a long time, but I
always have a problem when wap browser connects to Kannel. I find there
doesn't have a port to receive wap browser's link request because wap
browser always show the gateway timeout alert (I set port 9201 on the
wap
Hi
after i configuration the wap gateway and try to test it to make sure it's
working i try
(curl http://localhost:15000/shutdown?password=ros123;)
it return to me that error : curl: (7) couldn't connect to host, why?
can any one help me to solve that.
thankx
mohmmad jarwan schrieb:
Hi
after i configuration the wap gateway and try to test it to make
sure it's working i try
(curl http://localhost:15000/shutdown?password=ros123;)
it return to me that error : curl: (7) couldn't connect to host, why?
wapbox has no HTTP admin interface
- Original Message
From: mohmmad jarwan [EMAIL PROTECTED]
To: Hanna Kreitem [EMAIL PROTECTED]
Cc: [EMAIL PROTECTED]
Sent: Tuesday, 1 April, 2008 6:15:07 PM
Subject: Re: wap gateway error
thankx for replay
the wap box running at port 15000 and no firewall active
if ther is any other
Hi
i want to send MMS and i wandering can i use kannel as mmsgateway alone ,or i
used Mbuni that based on kannel ,or i use Mbunialone without kannel
what way more effective and more reliability .
Are three way is true (can send MMS with it)
: mohmmad jarwan [mailto:[EMAIL PROTECTED]
Sent: Monday, March 31, 2008 5:19 PM
To: users@kannel.org
Subject: MMS wap gateway
Hi
i want to send MMS and i wandering can i use kannel as mms gateway alone ,or i
used Mbuni that based on kannel ,or i use Mbuni alone without kannel
what way more
thanx for that but is ther any solution without using Mbuni.
- Original Message
From: Michael Sole [EMAIL PROTECTED]
To: mohmmad jarwan [EMAIL PROTECTED]
Sent: Monday, 31 March, 2008 3:33:38 PM
Subject: RE: MMS wap gateway
!--
_filtered {font-family:Cambria Math;panose-1:2 4 5 3 5
Not on Linux (that I know off).
There is a windows based app call SMSNow which is pretty good.
From: mohmmad jarwan [mailto:[EMAIL PROTECTED]
Sent: Monday, March 31, 2008 8:43 AM
To: [EMAIL PROTECTED]
Cc: users@kannel.org
Subject: UNS: Re: MMS wap gateway
thanx for that but is ther
ok thanx
- Original Message
From: Michael Sole [EMAIL PROTECTED]
To: mohmmad jarwan [EMAIL PROTECTED]
Cc: users@kannel.org
Sent: Monday, 31 March, 2008 3:45:19 PM
Subject: RE: Re: MMS wap gateway
!--
_filtered {font-family:Cambria Math;panose-1:2 4 5 3 5 4 6 3 2 4;}
_filtered {font
You need to use Mbuni as VAS MMS gateway for sending MMS, kannel itself
doesn't have any MMS modules. On the other hand to install Mbuni and
start working with it, you should have Kannel installed on the same
server. There is no need for Kannel to be running but it should be
installed.
PROTECTED]
*Cc:* users@kannel.org
*Subject:* UNS: Re: MMS wap gateway
thanx for that but is ther any solution without using Mbuni.
- Original Message
From: Michael Sole [EMAIL PROTECTED]
To: mohmmad jarwan [EMAIL PROTECTED]
Sent: Monday, 31 March, 2008 3:33:38 PM
Subject: RE: MMS
my website but its being
hosted at a data center.
What i would like to know :
1. If i use Kannel as the WAP gateway do i need anything additional in terms of
webserver etc ?
2. will i have to write wml pages and upload wbmp images from scratch? Where
will i be storing all these files ie under
I think the question is more : do you take care of the wap gw or your telco
has already a wap gateway ?
After it will be more easy to answer your question
BR
_
From: Sriram [mailto:[EMAIL PROTECTED]
Sent: lundi 19 novembre 2007 04:15
To: users@kannel.org
Subject: WAP gateway
Apache you can store it under htdocs. If you want it to be
hosted say by web hosting company make sure they have a wap gateway.
for question 2 writing your pages from scratch is more of a likely
option. My advice is that you use XHML MP which can make your site
accessible both via web and wap
Hi all
I need install an run a kannel wap gateway over iden phones (nextell
phones).
Some have using kannel wap gateway over this phones??
Regards ,
--
Vìctor Nieto
Hi all,
Is there any script out there for administrating WAP gateway for
managing users accessing through it?
If anyone is having any reference links please send it to me.
Thanx and Regards
Tushar
Hi all,
I have been using kannel since a long time..I am able to access
wap pages thru kannel wap gateway but the problem I m getting is
Images are not shown on the wap page. The warning I m getting is like:
WARNING: WSP: content-type image/gif not supported
Images
Hello Group,
With my Wap gateway I am able to access internal pages. But for pages
outside the firewall I
have to go through the proxy and proxy must verify me with my username and
password/
I can fetch all intranet pages however when I access.
google.com,
2006-12-20 11:49:51 [8081] [5
Hello Group,
Has anybody installed Wap gateway behind company's firewall and tested it
there with the
live phone.
If yes please let me know.
Thanks.
nagrik
Hello Group,
I have installed my wap gateway and I have tested it with the fakewap
command. Now I
want to test it with real phone. I have access to Motorola ascensioni P3
phone.
Can someone direct me to all the steps necessary to make my wapgateway
functional.
I probably will have to create
Arun Jain wrote:
Hello Group,
I have installed my wap gateway and I have tested it with the fakewap
command. Now I
want to test it with real phone. I have access to Motorola ascensioni P3
phone.
Can someone direct me to all the steps necessary to make my wapgateway
functional.
I probably
Arun Jain wrote:
Dear group,
I am testing my wap gate way.
1. My first command is
./bearerbox -v -1 smskannel.conf,
where smskannel.conf is as follow.
br, all wrong here... you are firing bearerbox up in SMS gateway mode only
then.
Please use this for simple testing:
$ cd gw
$
[13979] [0] PANIC: ./fakewap(SSL_write+0x41) [0x804f4a1]
***
I would also like to test my wap gateway from a live motorola phone with
T-mobile sim card. Can someone tell me
the steps for testing and also the errors I am making in starting my wap
gateway/fakewap.
Thanks
Hello Group,
I see examples to test sms gateway by typing test/..., however could
someone tell me as to how to
test the WAP gateway.
thanks.
arun
internet connection, everything works fine.
Now I'm facing that using wap connection, my telco wap-gateway don't
like the HttpConnection my j2me application tries to open.
So to let my j2me application talk to my webserver using a wap
connection, what should I do ?
1) configure the kannel wap
hello everyone,
I want to test Kannel as a WAP Gateway but dont know how
to do it. guide me after this step?
All the configurations for wap box is done in conf file. like wapbox port
and wapbox goup.
first i have started my bearerbox service with command ./bearerbox -v 1
aliraza raza wrote:
hello everyone,
I want to test Kannel as a WAP Gateway but dont know
how to do it. guide me after this step?
All the configurations for wap box is done in conf file. like wapbox
port and wapbox goup.
first i have started my bearerbox service with command
allows you to establish a TCP/IP stack
you can use Kannel as WAP gateway.
Stipe
---
Kölner Landstrasse 419
40589 Düsseldorf, NRW, Germany
tolj.org system architecture Kannel Software Foundation (KSF)
http://www.tolj.org
On Fri, May 19, 2006 at 10:47:46PM +0200, Rene Kluwen wrote:
RK Is this using the ETSI extended AT set?
RK Or some proprietary interface? Because that is what Nokia does with their
RK CDMA phones.
RK And it doesn't work with Kannel.
Proprietary.
--
Regards,
Alex Antropoff
On Fri, May 19, 2006 at 04:51:50AM +0200, Rene Kluwen wrote:
RK Kannel DOES support CDMA networks in some way.
RK You just need an upstream (SMPP or thelike) provider that delivers to those
RK kinds of networks.
RK
RK As for using Kannel with a CDMA SMS modem, I haven't found phones/modems
RK
19 mei 2006 10:47
To: users@kannel.org
Subject: Re: Looking for a CDMA SMS and WAP gateway (2nd posting)
On Fri, May 19, 2006 at 04:51:50AM +0200, Rene Kluwen wrote:
RK Kannel DOES support CDMA networks in some way.
RK You just need an upstream (SMPP or thelike) provider that delivers to
those
RK
Hello,
It seams that kannel only supports GSM networks, but I would like also
to support CDMA networks. Can I do that with Kannel? If yes, how? If no,
what other product I could use to support SMS and WAP on CDMA networks,
preferably open source?
It is my second posting. Can someone help me?
: Looking for a CDMA SMS and WAP gateway (2nd posting)
Hello,
It seams that kannel only supports GSM networks, but I would like also
to support CDMA networks. Can I do that with Kannel? If yes, how? If no,
what other product I could use to support SMS and WAP on CDMA networks,
preferably open
Hi Friends, Currently i'm having a wap gateway from a different vendor , and there is a radius server for user authentication . But it seems to be cant handle the access load. So we supposed to have kannel as our wap gateway , questio is , How i integrated kannel-wapgateway and our
Hi ,Can we use "MAP-URL" for load balancing ? as an example we have two different wap gatweways. one is kannel . but clients are using only one gateway's ip address as their gatway address.How would be balance the load ofaccess the gatewaysThank you , Kane.
Yahoo! Photos
hi all,
I am running kannel wap gateway and want to access it through my mobile
phone or through some wap simulator ?
I have a question that what will be the IP which I will enter as the IP
address of the gateway and what will be the Port no ?
thanks
Talk about Love/Friendship and get
at
Latestngreatest Forums
http://www.latestngreatest.net/cgi-bin/Blah/Blah.pl/Blah.pl
From: Aarno Syvänen [EMAIL PROTECTED]
To: Yasser Sultan [EMAIL PROTECTED]
CC: users@kannel.org
Subject: Re: Simulate WAP Gateway [again]
Date: Mon, 25 Apr 2005 16:57:40 +0200
That is more like a problem of GPRS, because wap
This would not be a simulation, but a real thing, would it ?
Aarno
On 25.4.2005, at 07:14, Yasser Sultan wrote:
Hi,
I want to simulate the working of Kannel WAP gateway ?
I have found one method here
http://www-106.ibm.com/developerworks/linux/library/wi-kannelwap.html?
ca=dgr-lnxw09WAPLinux
use the WAP gateway
address provided by my cellular provider, so if I change this address
to the address of my gateway than I suppose I will be able to showing
the working of kannel on a mobile phone ? (Please correct me If I am
wrong)
But do mobile operators allow connections
Subject: Re: Simulate WAP Gateway [again]
Date: Mon, 25 Apr 2005 16:57:40 +0200
That is more like a problem of GPRS, because wap gw is a part of GGSN.
CSD would usually work, and is not much slower either (strange but true).
Aarno
On 25.4.2005, at 15:00, Yasser Sultan wrote:
Yes , you are right
Hi,
I want to simulate the working of Kannel WAP gateway ?
I have found one method here
http://www-106.ibm.com/developerworks/linux/library/wi-kannelwap.html?ca=dgr-lnxw09WAPLinux
Which says that
Testing with a WAP-enabled mobile phone simulator
You need two machines, one running a Windows
I want to simulate the working of Kannel WAP gateway ?
I have found one method here
http://www-106.ibm.com/developerworks/linux/library/wi-kannelwap.html?ca=dgr-lnxw09WAPLinux
Which says that
Testing with a WAP-enabled mobile phone simulator
You need two machines, one running a Windows® operating
Hi Everybody :
I am discovering the kannel open source package,i find
it really great,and planes to use for some combinded
voip and sms applications,thanks a lot for the people
having got this idea.
I still have some problems answering the following
question :
When should one use a public Wap
Tech mark wrote:
hi ,
Can v implement this wap gateway for GPRS network ? i meant can it possible to access wap contents via GPRS using kannel wap gateway ?
If it is possible , how many clients allowable to access via wap gateway ? Is there any load balancing mathod to use ?
yes. Kannel
hi ,
Can v implement this wap gateway for GPRS network ? i meant can it possible to access wap contents via GPRS using kannel wap gateway ?
If it is possible , how many clients allowable to access via wap gateway ? Is there any load balancing mathod to use ?
plz advice me
Thanx in advance
Most operators have different GPRS APN's for MMS, Wap, and also one for
public internet.
If you want to use your own WAP gateway (e.g. Kannel) use the public
internet APN rather than the Wap APN.
Best regards,
Rene Kluwen
Chimit
- Original Message -
From: Michael Mugge [EMAIL PROTECTED
HowdyList Members !
I would like to connect to a WAP gateway through
GPRS, and fetch a simple wap page. (TheUDP level of thestack
isworking now.)
I readthrough the standards about WTP and
WSP, but however an example would be very helpful.
Does anyone have an example (eg. a package dump
Try first with dial-up link (CSD). GPRS has problems of its own
Aarno
On 11.1.2004, at 12:10, Rozsahegyi Robert wrote:
Howdy List Members !
I would like to connect to a WAP gateway through GPRS, and fetch a simple wap page. (The UDP level of the stack is working now.)
I read through
Dear Arno,
Thank You for the quck reply.
I have to confess that I don't try this connection
on the Kannel gateway, just on my GSM operator's WAP gateway.
(t-mobile)
I think I came over the GPRS part of the
connection, I can send UDP packeges and I receive answer packages like
this.
(UDP
when up and running the wap gateway , in wapbox shown few unsatisfied errors.
[7] WARNING: WSP: Device doesn't support charset ISO-8859-1 neither UTF-82004-12-06 12:44:03 [2370] [7] INFO: WBXML: No wbxml version given, assuming 1.1
where could be the error ? what kind of configuarions has
hi
I installed and ran wap gateway.
bearbox and wapgateway started.
when try to access a url of a internal webserver , from wap simulator gives
Could not get URL http://internal ip:9201/HTTP Error : 404 (Connection refused (Error #10061))
what is this error ? how cqan i prevent this error
H'llo friends,
I refered to the site and did the following:
1. Started the bearer box and wap box as follows:
./bearerbox -v 1 piyush.conf
./wapbox -v 1 piyush.conf
The Wap gateway server is connected to the internet via a proxy.
2. Downloaded the Nokia 7210 SDK
Made it to point
Hello,
I want to if there is a way I can control/authenticate the mobiles that access my wap gateway. I installed Kannel versio 1.2.1 and it's already running, but I need a way to control which phone numbers can access it. How can I do that?
Thanks,
emotaFREE pop-up blocking with the new MSN
I'm having trouble getting my Motorola v710 (Verizon) phone to access the
Internet through a kannel WAP gateway I've set up on my server.
It works fine when I just use an HTTP gateway with squid as the proxy.
I don't know if the problem is my phone or the kannel setup, since I have
no other
Dear WAP Kannel Uses,
Does anyone know of a WAP gateway that I can use?
Thanks
Hillel Bilman wrote:
Dear WAP Kannel Uses,
Does anyone know of a WAP gateway that I can use?
In case I mis-understood you, and you mean Is there an public
available Kannel WAP gateway installation, that we may try/use.
Yes, there is. The Kannel REFPOOL machine (IP 62.96.19.67) services
I use the kannel just the same way like Wap Gateway does and everything
works fine except for one thing. The Wap Gateway quite often questions
the telephone.
Maybe I'll explain it more precisely.
At the first connection with the Wap Gateway it looks like this:
From the packages:
09:22:41.858333
But your phone does accept 500k downloads? Does it support ESAR, then ?
Aarno
On 20.11.2003, at 23:52, Bruno Rodrigues wrote:
Igor Ivoilov [EMAIL PROTECTED] wrote:
I have changed packet size to be 1400 on my production server
and don't see any problem for now.
I have not see javagames more than
Aarno Syvänen [EMAIL PROTECTED] wrote:
But your phone does accept 500k downloads? Does it support ESAR, then ?
All the nokia's symbian os at least.
Unfortunately our CMG also didn't support ESAR, so we had to do a small
symbian app that fetches itself (through regular http) that 500+K
Hi All,
I have this problem with the WAP gateway I did setup.
The problem is that a maximum of 254/255 packets can be send concerning 1
file.
This means that if I want to download a file with a size higher as 143KB the
transmission fails :-(
The error I got is the following:
In wapbox.log
PROTECTED]
|Subject: Re: kannel WAP gateway and Siemens S55 - SOLVED!
|
|
|* Wash [EMAIL PROTECTED] [20030909 08:39]: wrote:
|
| Dear Ladies and Gentlemen,
|
| I have setup kannel-1.2.1 as a WAP gateway and it seems to work
|fine so far.
| However I have found a big problem with Siemens S55 phone
* Wash [EMAIL PROTECTED] [20030909 08:39]: wrote:
Dear Ladies and Gentlemen,
I have setup kannel-1.2.1 as a WAP gateway and it seems to work fine so far.
However I have found a big problem with Siemens S55 phone. It cannot work
with the gateway, even though other phones do
Hi,
I have configure and working kannel 1.3. It seems to work fine. But I need
to configure a home page.
Does anyone knows how to do this?
Thank You.
Carlos.
Dear Ladies and Gentlemen,
I have setup kannel-1.2.1 as a WAP gateway and it seems to work fine so far.
However I have found a big problem with Siemens S55 phone. It cannot work
with the gateway, even though other phones do.
It is in this regard that I would like to request anyone who has
Navjot Singh [EMAIL PROTECTED] wrote in message
news:[EMAIL PROTECTED]
hi,
Are you sure both of your config files have same bearerbox port, and
different wapbox ports?
May be you can post your config files.
Hi all,
I am happy to say that I now have 2 instances running on one box. I did
On Tue, 2003-08-19 at 23:40, Raj wrote:
Now the next problem I have is that only one log file is written to when I
start 2 bearerbox and 2 wapbox. The logs are all written to the bearerbox
logfile of the bearerbox I started first.
I need to be able to split them out. Any ideas?
Yeah...
Hi Raj,
I didn't try it yet. However, I'd assume, if you start each instance
with different configuration files it should work. Make sure each
instance uses different ports...
Hope that helps,
Dominik
On Mon, 2003-08-18 at 10:56, Raj wrote:
Raj [EMAIL PROTECTED] wrote in message
news:[EMAIL
Dominik Dahlem [EMAIL PROTECTED] wrote in message
news:[EMAIL PROTECTED]
Hi Raj,
I didn't try it yet. However, I'd assume, if you start each instance
with different configuration files it should work. Make sure each
instance uses different ports...
Hope that helps,
Dominik
That's what I
|To: [EMAIL PROTECTED]
|Subject: Re: Multiple instances of kannel WAP gateway
|
|
|Bastian Ramm [EMAIL PROTECTED] wrote in message
|news:[EMAIL PROTECTED]
| Hi!
|
| Should be no problem starting two instances each with its own
|config file.
|
| On Wed, 23 Jul 2003 15:21:54 +0100
| Kothary, Raj [EMAIL
Raj [EMAIL PROTECTED] wrote:
Dominik Dahlem [EMAIL PROTECTED] wrote in message
news:[EMAIL PROTECTED]
Hi Raj,
I didn't try it yet. However, I'd assume, if you start each instance
with different configuration files it should work. Make sure each
instance uses different ports...
Hope that
Can anyone tell me what is the best way of configuring kannel and compiling it.I can´t make the wapbox work. it says that it can connect to the bearer box on port 13002.Thanks,Carlos
To: [EMAIL PROTECTED]
Sent: Friday, August 01, 2003 10:12
AM
Subject: WAP gateway setting
Hi,
I'm looking for someone who can help me solving the
problem.
I'm quite new to wap gateway anf currently try to run
bearerbox and wapbox with kannel.conf..below is my
Hi,
I'm looking for someone who can help me solving the
problem.
I'm quite new to wap gateway anf currently try to run
bearerbox and wapbox with kannel.conf..below is my configuration file:
group = coreadmin-port = 13000wapbox-port =
13002admin-password = barwdp-interface-name
Hi!
Should be no problem starting two instances each with its own config file.
On Wed, 23 Jul 2003 15:21:54 +0100
Kothary, Raj [EMAIL PROTECTED] wrote:
Hi,
I think it is possible for one machine to run multiple instances of kannel
so that it have 2 WAP gateways, but how do I make sure that
. With the help of these you
can run two instances of wap gateway.
Rgds
sunil
-Original Message-
From: Kothary, Raj [mailto:[EMAIL PROTECTED]
Sent: 23 July 2003 19:52
To: '[EMAIL PROTECTED]'
Subject: Multiple instances of kannel WAP gateway
Hi,
I think it is possible for one machine to run
1 - 100 of 107 matches
Mail list logo