[Elecraft] 15 pin ACC Y-Cable Question

to the band decoder as this URL shows http://static.dxengineering.com/global/images/chartsguides/u/ums-bcd-10.pdf I'd like to know will I have conflicts between the SPE 2kfa and the band decoder ? some of the Data ABCD are using the same pins .. Anything I should be aware of ? Thanks Ed N5DG

[Elecraft] Solar Controller Question

or a good sized boat or a day or two portable operation for something like the US Island QSO party coming up. We would want to run 100 watts with the K3. This would be a 12 vdc system with something in the range of 100-140 watt panel. Probably two 6 vdc deep cycle batteries. Ed W0SD

[Elecraft] k3 audio problem

Contact Elecraft service. I had a similar problem a couple of years ago. The radio had to go to the factory for diagnosis. We ended up with a board replacement. Ed K6ED __ Elecraft mailing list Home: http://mailman.qth.net/mailman

Re: [Elecraft] KX3 + SignaLink USB noise problems

The Signalink needs help. Take a look at K7SFN's Web Site for some information on what is needed. We did some research and came up with some mods that make a world of difference. The previous post also is good advice. Ed

Re: [Elecraft] KPA500 problem

Send it back for the TR switch update. This is a known problem with early KPA500s and there is an easy factory fix. Ed W0YK _ Ray W2RS wrote: My KPA500 amplifi_es_ (file://\\es) normally but seems to have a switching problem on receive. The receiver

Re: [Elecraft] K3 Line-Out help needed

What level is LIN OUT set to in the CONFIG menu? 73, Ed W0YK __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted

Re: [Elecraft] K3-RTTY-No Diddles

for me. Ed K6ED __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support

Re: [Elecraft] K3-RTTY-No Diddles

EXTFSK is only required if a USB-Serial interface is used which doesn't have an adequate UART implementation to support 45 baud and the 5-bit code. The Digi International Edgeport/4 and /8 interfaces work fine without EXTFSK. The microHam interfaces also work fine without the EXTFSK module. Ed

[Elecraft] SOLVED: KX3: Hi SWR on 20m 30m after KX3-2M install

support. 73s Ed/WE2H Sent from my iPad Hi I just recently installed the 2M transverter in my KX-3. I?m now noticing high (11 to 25) SWR readings on 20m and I wondered if this might be related (I don?t recall such high readings before). I?m using an off-center fed dipole that has worked

[Elecraft] KX3: Hi SWR on 20m 30m after KX3-2M install

on the inductor while doing this. L40 (as I recall) felt pretty tight and I may have inadvertently pushed it too hard. What would be the symptoms of an open circuit on either of those inductors? Other than high SWR on 20m and 30m, I haven’t seen any anomalous behavior. 73s Ed

[Elecraft] K3 Remotely Program CW messages

Can you program the CW messages in the K3 remotely? If so how? I can't figure out a way to do it! Thanks, Ed W0SD __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm

[Elecraft] KX3 More on Sideband Nulling Issue

is observed in the signal level as the null operation progresses. There is good suppression when FL1 is selected. This KX3 is factory-built, S/N 0162, latest firmware. Any ideas? --Ed-- --- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com

[Elecraft] KX3 Opposite Sideband and IF Image Nulling Procedure Problems

to check next... --Ed, N3CW-- --- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help

[Elecraft] KX3 CW Receive Issue

was not there before, although I sure didn't notice it. I did notice it today with all the 10 M CW activity, but the problem is on all bands; signals. Any others experiencing this? --Ed-- --- This email is free from viruses and malware because avast! Antivirus protection is active. http

Re: [Elecraft] KX3 CW Receive Issue

Hello, Noise blanker is off. --Ed- --- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo

[Elecraft] OT: Request for EMI/RF Interference Opinion

no luck I need to get some opinions from someone with more experience; thanks! --Ed-- --- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com __ Elecraft mailing list Home

Re: [Elecraft] K3 filter plots

Yes, the link below works, but the link to the crystal filter plots that is at that top of that webpage is broken. Ed W0YK - Phil W7OX wrote: This link can be useful and still works: http://www.elecraft.com/K3/Roofing_Filters.htm

Re: [Elecraft] [K3] A speaker for the K3 (Phonema)

I like the idea of a speaker that reasonably matches the K3. This one looks nice; however, I'd like to see two speakers in one enclosure so I can use the sub-receiver without having to have two separate speaker units on the desktop. --Ed-- --- This email is free from viruses and malware

Re: [Elecraft] WRTC 2014 - Congratulations, Elecraft!...(and firmware update)

over a distance of 80 miles, from the southern NH border to the entrance to Cape Cod in southern MA. There were some clusters of sites where 15 or so WRTC stations were located just a couple thousand yards from each other. The 100 watt power limit helped a bit, too. Ed W0YK

Re: [Elecraft] WRTC 2014 - Congratulations, Elecraft!...(and firmware update)

-Test. ;) I believe that the best logger for you is the logger that works best for you, not the logger that works best for someone else, or is the most popular logger among contesters. Ed W0YK Joe W4TV wrote: On 2014-07-24 12:56 PM, Guy Olinger

[Elecraft] K3-100 for sell

assembled K3 serial # 32xx No dings , scratches , scuff's in none smoking environment I will ship to you in factory box , (double boxed ) with manual and power cord . $ 2,285.00 You have any questions please Email Tnx Ed N5DG --- This email is free from viruses and malware because avast

Re: [Elecraft] K3 M/M Contest stations

. This is a good thing. It would be nice if the radio non-specific configuration parameters were transferrable but that feature currently is not available. Ed W0YK Phil, W7OX wrote: I'm not sure. My recollection is that someone posted a few weeks ago that he has two K3s and could not load the config file

[Elecraft] K3 Wattmeter Cal and Tech Mode

? Thanks for any hints. --Ed-- --- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http

Re: [Elecraft] K3 Wattmeter Cal and Tech Mode

Hi Ken, Seems no PWR setting from 0 up to 100 watts makes any difference. I only get the WMTR MW screen in the config menu. I can't get to the LP or HP screens to make any adjustments. Tech Mode is turned on. --Ed- _ From: Ken K3IU [mailto:kenk...@cox.net] Sent: Monday

[Elecraft] K3 Band and Mode Switch Tones

bounce/noise be responsible? This anomaly also seems to happen more often (but not always) if I change bands or modes quickly. --Ed-- --- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com

Re: [Elecraft] KX3 through TSA Security ?

through a separate and VERY minimal line, with no shoe removal nor pocket emptying. 3 minutes tops. Awesome! Ed Tanton   website: http://www.n4xy.com   All emails IN OUT checked by Norton AntiVirus with AutoProtect -- Wag more / Bark less

Re: [Elecraft] K3 BATT LOW

the problem. I agree, that it would be great for both the K3 Operators Manual and Fred's book to cover this error message. Ed W0YK ** Ray ND8L wrote: Getting this message in the VFO-B area. Can't find reference to the battery in the K3 Owner's

Re: [Elecraft] KXPA100 Shipping Status Update

date. Ed W0YK/4 Sent from my Verizon Wireless 4G LTE DROID Robert Vargas - KP4Y k...@yahoo.com wrote: That's why I keep insisting that my KX3 will have almost three years by the time I'm finally able to use it on 2m with the so much anticipated 2m module. I love ElecraftI really do

[Elecraft] SSB 2 audio profiles ?

I have my K3 TX EQ set for ear piercing penetrating audio to help work the DX .. I have a group I rag chew with a few times a week and they are complaining ! Is their some way to have 2 TX EQ settings that is easily switched between ? one for DX and the other for rag chew. Tks Ed N5DG

Re: [Elecraft] SSB 2 audio profiles ?

OK Tks all, I've got it , it was EZ in the K3 EZ program Ed On 11/25/2013 12:52 PM, Ed Stallman wrote: I have my K3 TX EQ set for ear piercing penetrating audio to help work the DX .. I have a group I rag chew with a few times a week and they are complaining ! Is their some way to have

Re: [Elecraft] Fwd: K9W Wake Atoll DXpedition Has Been Approved - Hope To Be QRV This Weekend

Their website shows the CW and SSB transmit frequency of 50.107 Ed W0YK Lance W7QJ wrote: Vic, they told me they are not planning to do anything on 6m. However, if you are interested in contacting KH9 on 6m, WA2YUN has a great station set up there. His email is good on QRZ.com. He has

[Elecraft] K3 to Expert Amp cable ?

will be setup the same. Thanks for your help Ed N5DG __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http

[Elecraft] K3 No signals in Data Mode

When I switch my K3 to the data mode I do not hear any signals. I hear plenty of PSK in USB on 20 meters and DM780 will decode them when in USB. When I switch to Data Mode I just get background noise with what sounds like a very narrow filter setting. Ed AB8DF

[Elecraft] MH2 Microphone forsale

Excess to my needs selling my Elecraft Mh2 mic for 45 dollars shipped non smoking shack or swap for MH3 Ed Reply to w...@tampabay.rr.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http

Re: [Elecraft] P3 power supply

I use a RCA Phono Y-adapter cable on the K3 12VDC output. You may need the K3 12VDC high current mod, though. Ed W0YK -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of John Sent: Sunday, August 18, 2013 2:36 PM

Re: [Elecraft] PR6 ctrl line

Sometimes popular usage trumps correctness. ;) For those who care to understand this point, see http://en.wikipedia.org/wiki/D-subminiature. Ed W0YK Jim KL7CC wrote Thank you, Fred. And as you well know, there is no such thing as a DB9 connector, it is a DE9. But, as you say

Re: [Elecraft] Audio transformers needed

Two that I have used with good results are “Triad TY-304P” and “Etal P-3356”. These are quality transformers and are readily available. Just enter the part number in your search engine. Radio Shack also has several available that should work just fine. Just a note: A transformer is not

Re: [Elecraft] looking for iPad software

At the APP Store, search on Ham Radio Logging . Fall back on Ham Radio if you don't find something for Logging. Ed Tanton   website: http://www.n4xy.com   All emails IN OUT checked by Norton AntiVirus with AutoProtect -- Wag more / Bark less

Re: [Elecraft] K3 Setup Failing

What Don is saying is true. My manual, page 58 shows the factory default as 4800 b. Try resetting it to 38400 using the “config” menu. You will have to also do the same with your computer. Then try reloading the software. Anything you have saved with your present setup could be corrupted

Re: [Elecraft] K3 Setup Failing

Brian There are two other things you can check. On the K3, when pressing the “Xmit” button, the one above the volume control, does the red “Xmit” LED light? It is located above the “Phones” jack. If not look over on the extreme right of the display. There is an arrow that indicates

Re: [Elecraft] K3 Setup Failing

Brian What does the display show when you manipulate the power control knob. It must have the green LED lit indicating “PWR” above the knob. If I remember correctly the calibration process will set the output to “0” after calibration.

Re: [Elecraft] Ideal RTTY filter.

proposal. Ed W0YK According to W7AY: The ideal RTTY filter is 280 Hz wide. Narrowing it further by 60 Hz doubles the error rate. The article references: http://www.w7ay.net/site/Technical/RTTY%20Transmit%20Filters/index.html Which doesn't come out and say the above! It's talking about

Re: [Elecraft] K3 -Advice: how to configure APF for least ringing

I work mostly CW weak signal and have not heard ringing with the K3 .. Now I will say if you have your tones CW Pitch set at 800 Hz + or - it may sound like ringing to you , you might try lowering the CW Pitch say around 600 Hz or even lower Ed N5DG On 5/10/2013 7:36 PM, Matt Zilmer

Re: [Elecraft] P3 Use with K3

Alan Alan Bloom explained the effect you are seeing on 14, Apr. 2013. You can look in the “Earlier messages” and find his post. It is essentially the same as Fred answered you with. Ed __ Elecraft mailing list Home: http

[Elecraft] lp pan and Yamaha UR22 sound card forsale also.

lp pan and Yamaha UR22 sound card forsale also. E mail me off the list. Thanks Ed Wp4o w...@tampabay.rr.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm

[Elecraft] signalink usb and cable for sale aslo K3 serial Number 69xx

Hi Gang I have 2 slightly used new signalink Usb and comes with K3 chip and line in/out cable 75 dollars for each one shipped. Also have a 5 month old Factory assembled K3 with sub receiver and kxv3a-F/ KAT3-F and microphone for sale 2 500 CW FILTERS. 73 Ed, Wp4o, Tampa florida w

Re: [Elecraft] P3 desires

I can think of a number of things that could be useful in the band pass window. In addition to the notch I would have use for an indicator for the receive offset frequency and also the peak filter. Things could get busy unless things were set up on a selective basis. K6ED

Re: [Elecraft] K3 Utility Noise

we have an FCC part B specification. This dictates the noise characteristics allowed for home use. If a computer power supply doesn't state FCC part B compliant on it somewhere I won't touch it. I've been there a couple of times and don't want to go there again. Ed -- View this message

Re: [Elecraft] FSK-D wiring

and individual functional cables can be swapped in and out both for easy configuration of any system as well as easy troubleshooting. It is about as neat a cable mess as can be had without making a specific special cable for just one configuration. Ed W0YK Jim AB3CV wrote: The recent FSK-D

Re: [Elecraft] Writing K3 Control Add-in for Windows4P3 and need some advice

on, using the IP Power switch. Ed K6ED -- View this message in context: http://elecraft.365791.n2.nabble.com/Writing-K3-Control-Add-in-for-Windows4P3-and-need-some-advice-tp7571812p7571878.html Sent from the Elecraft mailing list archive at Nabble.com

[Elecraft] KX3 (or other amateur gear) in aircraft

. Spurious emissions from a non-aviation radio would be, though. Anyway, bottom line is it's OK to have a general coverage receiver that covers the aviation VHF bands, but any transmitter must be approved and the station specially licensed. 73s Ed/WE2H

Re: [Elecraft] Writing K3 Control Add-in for Windows4P3 and need some advice

with your VOX settings you may want to start looking for an outside cause, like the effects of RF, or something. The K3 is known as having an excellent VOX system. 73 Ed On 3/26/2013 10:10 AM, k5oai [via Elecraft] wrote: Ed wrote Tom I would think you will find the VOX on/off

Re: [Elecraft] A Different View--K3 Reduced-bandwidth RTTY Analysis

As far as I know, this enhanced DSP filtering is only on the K3 FSK transmitted signal. There is no impact on other modes, digital or otherwise, only FSK-D. Ed W0YK Milt N5IA wrote: Since I am NOT a RTTY operator I am asking if this DSP software revision is applicable to other modes. I

[Elecraft] p3 has solid spike on not all bands

Gang I am using my P3 mainly for 6 meters but when I switch to another Band I get a solid spike in the middle of the screen an no movement. Please advise Also the two arrows green and purple are to the extreme right bottom on the screen.. Ed Wp4o

Re: [Elecraft] K3 RTTY bandwidth already too narrow?

considerably. Properly filtered FSK bandwidths are similar to good, and properly adjusted, AFSK bandwidths. Ed W0YK __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post

[Elecraft] K3 reduced-bandwidth RTTY analysis

281 firmware will be released to production soon. Meanwhile, if anyone is interested in trying it, let me know and I'll email it to you. Ed W0YK -Original Message- From: RTTY [mailto:rtty-boun...@contesting.com] On Behalf Of aflow...@frontiernet.net Sent: Thursday, March 21, 2013 6

Re: [Elecraft] K3/0, Writelog, FSK

If you haven’t already don this, go to the MMTTY site and download “EXTFSK”. This is a patch that allows the proper keying for FSK with MMTTY. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

[Elecraft] KX3 Noise Reduction Performance

this? Any ideas on how to make the performance more consistent across bands? Ed, K8SZN __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft

[Elecraft] KX3 Noise Reduction Performance

this? Any ideas? I'm running the current firmware. Ed, K8SZN __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted

[Elecraft] P3 issues

qrn on the band and you turn on the noise blanker on the K3 the p3 does not reflect that, I also run a LP PAN with the NAP3 Software and it rocks what I can see due to QRN on the P3 I can see with the LP Pan and NAP3 software. Hope there is a fix for this down the road. Thanks Ed WP4o

Re: [Elecraft] P3 issues

. Hope there is a fix for this down the road. Thanks Ed WP4o * __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted

[Elecraft] Would like to purchase a used K3 from a Non Smoking Shack, please e mail me w...@tampabay.rr.com

Would like to purchase a used K3 from a Non Smoking Shack, please e mail me w...@tampabay.rr.com. Thanks Ed WP4O __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm

[Elecraft] K2 - Turns on, locked in transmit

on the list. Since all controls are seemingly locked I am not able to copy down any settings. Thanks for any direction, Ed - ad7gr -- View this message in context: http://elecraft.365791.n2.nabble.com/K2-Turns-on-locked-in-transmit-tp7568316.html Sent from the Elecraft mailing list archive

[Elecraft] K3 RTTY Delay on RX

it to drop out right away? Thanks, Ed W0SD __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net

Re: [Elecraft] K3 RTTY Delay on RX

I forgot to mention I am using FSK D On 1/3/2013 5:16 PM, W0SD Ed Gray wrote: I have a delay after I stop sending RTTY before going into RX. It is just long enough to be annoying. I am using Writelog. I have it on one K3 and not another. I am using version 4.51 on both K3's. I have read

Re: [Elecraft] K3 RTTY Delay on RX

during phone SS in Nov. I think Joe W0DB who operated from here had something plugged into PTT in for SO2R but I have to confirm that with him. More next week. Thanks Dave! Ed W0SD On 1/3/2013 10:04 PM, Dave Hachadorian wrote: Are you using PTT via RS-232 command? I have noticed

Re: [Elecraft] How to avoid Elecraft list email overload: Nabble andother web archives

by focusing on groups of messages by topic. I can see the entire thread in one place without the mental blizzard of going through an unsorted Inbox on diverse topics. Ed W0YK Eric WA6HHQ wrote: Instead of receiving an email for every posting, ship There is a 'no mail' option on your elecraft

Re: [Elecraft] Rigblaster Plus with Elecraft K3

to transmit using the AFSK or FSK method before you setup the hardware and software. The PC connection to the RIGblaster Plus II can either be Serial RS232 or USB, per the manual. Ed W0YK -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun

[Elecraft] Wall wart for KX3

adaptor would be capable of 2A at 13.8 V to support running the radio with no (or fully discharged) batteries at full power, and would not exceed 15 V with no load. While I'm wishing, it would also be smalland lightweight. Any suggestions? thanks, 73 ed N9EP

Re: [Elecraft] Big weakness in Macro's

to implement. Wayne said he would look into it so I hope it happens. Ed W0SD On 12/8/2012 1:20 PM, Wayne Burdick wrote: Ed, The switch emulation commands provide a method of activating functions for which there are not yet direct commands. In many cases both methods are available. For example, you

[Elecraft] Big weakness in Macro's

the programming commands in the K3 pretty weak IMHO. Ed W0SD __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted

Re: [Elecraft] FS: Built W2 with 1.8-54 mhz 2 KW directional coupler

The W2 has been sold, lots of buyers. Thanks __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by:

Re: [Elecraft] OT CQWW contest results - location

http://cqww.com/publiclogs/ Ed W0YK Robert KE2WY asked: About two weeks ago, before the contest, I came across a site that had a database of actual Cabrillo logs from previous CQWW contests - and perhaps others. One could download someone's file and look it over, analyze it, etc

Re: [Elecraft] K-Line system integration questions

respectively. This assumes that the 2x1 RS232 manual switch is what we think it is ... a SPDT DB9 switch. Ed W0YK Dick K6KR wrote: Your RS-232 switch is just what the doctor ordered for K3 and P3 firmware updates. The KPA500 serial port is not daisy chained with the K3 and P3. The KPA500 uses

[Elecraft] FS: Built W2 with 1.8-54 mhz 2 KW directional coupler

I would like to sell my built W2 power meter(Mint condition). I find I just don't use it. Includes the 1.8 to 54MHz 2KW Directional Coupler, serial update cable, remote sensor cable, and manual. $185 shipped USPS CONUS. Price is firm. Respond off-list. Thanks Ed W0SD

[Elecraft] KX3 Low Cost Power Supply

and isn't a problem if you are using a coax-fed antenna. I'm not sure how it would work if you were using a long wire connected directly to the rig that runs in close proximity to the power supply. But, for my use, this is going to do the job nicely. Very light weight, and great for portable operation. Ed

[Elecraft] K3 Requested Change Ideas

for listening and your great support. Ed, K5EK __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http

Re: [Elecraft] K# Requested Change Ideas

Forget the third item - CW during SSB keying. It works on both inputs. It is my Microkeyer II that is inhibiting the keying during SSB. Now to see if I can change that. Ed, K5EK __ Elecraft mailing list Home: http

[Elecraft] KAT500 Matching Range Power Limits

with less than 100 watts. Then I will show a 1:1 SWR, and I'm ready to go with my 1000 watts. Operationally, what is the meaning of the 3:1 SWR limit for 1000 watts as shown in the KAT500 specs? Will the KAT500 fault because it is matching a 14:1 SWR at high power? --Ed

[Elecraft] P3 Left Edge Function

Great Idea. It would eliminate an awful lot of knob turning and button pushing. Ed Kuebert, K5EK k...@arrl.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm

[Elecraft] Looking for QRP Balun

I'm looking for a small 4:1 QRP balun to use with my KX3 (hence, it needs only 10 watt power capability). Can anyone direct me to a design or an existing product? Thanks. Ed/K8SZN __ Elecraft mailing list Home: http://mailman.qth.net

[Elecraft] More KAT500 PTT Questions

open whenever the KAT500 senses a high SWR and retunes, even if on the same band? It would be impractical for me to anticipate KAT500 retuning when moving into a new band segment and try to shut down the amp per the procedure on page 13. --Ed

[Elecraft] KAT500 With Older Amps

Any KAT500 buyers plan on using their tuner with an older amp such as the SB-220? If so, please post your experience with that setup, where the KAT500 is seeing 800-900 watts or so; thanks! --Ed-- __ Elecraft mailing list Home: http

Re: [Elecraft] K3-PR10

and desense specs. It is a good design trade-off, but there are times when more gain is needed on these higher bands. Ed W0YK Tim M0AFJ wrote: Just a question, does the K3 really need a 10M preamp, I know it's as deaf as a post on 6 but mine seems very lively on 10

[Elecraft] Icom/KPA500/KAT500 Question

side connected to the KAT500 using the KPAK3AUX cable (which is the same cable as the E850463? --Ed-- __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post

[Elecraft] HELLO

you should give this a look http://www.consumernews7ch.net/work/?money=92807 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net

[Elecraft] K3 utility problem

USB/RS232 cable and that cable works fine with my logging programs, (none of which are open and they don't seem to be conflicting). My OS is Windows XP. Any thoughts? Ed, KR3E __ Elecraft mailing list Home: http://mailman.qth.net

Re: [Elecraft] K3 - HRD

NOT just apply or remove power. You should able to add a button for power down. Also missing, at least I can't fine them, are VOX on/off. In looking at the K3's programmers guide I cant find where these commands are available within the K3 yet. Ed * ** ** *K6ED

Re: [Elecraft] K3 - HRD

*With HRD you do have access to the Main/Config functions. Press the Menu button located towards the center of the group of buttons on the right side of the screen. You will get a listing that includes both the Main and Config items. Click on an item and you will be allowed to make

[Elecraft] WTB: E-MU 0202 Sound Card

Looking for an E-MU 0202 audio interface; thanks... --Ed-- __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted

[Elecraft] K144XV with KRX3

about it. Thanks, Ed W0SD __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help

[Elecraft] For Sale: KX1 with Internal Tuner

For sale - absolutely mint KX1 with KXAT1 antenna tuner option. Very low usage. 2 band version (40 and 20), serial number 00905. Lithium AA batteries inside. $350, plus $12 for USPS Priority shipping. --Ed-- __ Elecraft mailing list

[Elecraft] K3 NB Generates noise

then 2,3,4, or 5 with 4 being best ! Is this normal ? I was thinking the higher numbers would reduce more noise ? Using IF-MID and WID 1 has more noise and 7 is less Thanks Ed __ Elecraft mailing list Home: http://mailman.qth.net/mailman

Re: [Elecraft] K3 NB Generates noise

Fred , N5GE and Guy , Thanks all very good explanations and great advice . I am using FW 4.51 and I believe it's good improvement . I have the IF NB turned back and am hearing some weak signals on 6m . just worked CT1HZE . Ed At 05:10 PM 7/18/2012, Fred Jensen wrote: Ed, First off, make

Re: [Elecraft] K3 static bleed resistor necessary or already in rig?

Both the KANT3 and KAT3 provide antenna surge protection, as well as resistors for bleeding off static DC charge Ed N5DG At 07:23 PM 7/16/2012, NH7RO wrote: I recently read on an antenna forum about installing a 40k ohm resistor across the RF input of a transceiver via one side of a PL

[Elecraft] Toggle Macros

have had just one on my 756 Pro III (which now I will sell) for many years. Ed, K5EK __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft

[Elecraft] K3: HI TEMP

the temp sensor. The front panel temp sensor appears to read a normal temp and the fans work properly. Does anyone have any suggestions as to where to troubleshoot the problem? What is the voltage on the temp sensor (transistor)? Ed K1EP K3 #66

[Elecraft] Want to buy

looking for an LP-PAN and sound card for the K3 ..let me know what you have and price Thanks Ed N5DG __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post

Re: [Elecraft] CW Key Suggestions

Check out Larry's paddles at: http://n0sa.com/ Beautiful machine work with highly efficient low-mass arms; a real bargain for the price he charges. There is also a single-lever version available. --Ed-- __ Elecraft mailing list Home

[Elecraft] KX3 AGC FD Issues and AGC Settings

. I'm hoping the ability to set these parameters will get rid of the somewhat annoying thumping. Any other KX3 users notice AGC issues during FD? --Ed-- __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help

<    1   2   3   4   5   6   7   8   9   10   >