I'm running I3 utils from both Win7-64 and from Ubuntu 12.04. At
38,400 bps, neither of them take this long (4400, 2200 sec).
Are you operating that serial port at 4800 bps? You could improve
your firmware load time by increasing it to 9,600, 19,200, or 38,400.
73,
matt
W6NIA
On Thu, 23 Jul 201
Hello All
I recently ordered a KRX3A and KSYN3A board for my K3. I was running firmware
version 4.58 so I thought I'd better update it in readiness for the new
arrivals.
The computer I use for radio is 32 bit running Win98se, it works very well with
my homebrew logging program which integrates
The first cardinal rule when a peripheral or device quits working under a
Windows OS: check/reinstall the driver and look for anything that might have
changed in software. I cringe at the number of modems, sound cards, etc.
which have been thrown in the trash by people who didn't understand the
On Mon, Mar 30, 2015 at 8:02 AM, GDR wrote:
> ...This is the same computer I have been using all along with all of my
> Elecraft equipment and it worked last time,,,
I had a Windows 7 laptop that ran my station perfectly for years. Then one
day it would not send CW to my
Sort of related to your problem...
Last week I bought the PX3 for my KX3. The PX3 required a much later firmware
installed in the KX3 than was in it (I had not kept it current; if it ain't
broke, don't fix it mentality). So, I downloaded the current KX3 utility, got
the latest firmware and
There is a step by step procedure in K3 Utility Help, Troubleshooting, MCU Load
Failure.
Dick, K6KR
On Jun 16, 2013, at 9:14 PM, k.i...@comcast.net wrote:
>
>
> Tried to update the K3 firmware to 4.67. First, I updated the K3 Utility to
> the latest version 1.13.5.9. The moment I hit Send
Tried to update the K3 firmware to 4.67. First, I updated the K3 Utility to the
latest version 1.13.5.9. The moment I hit Send All New Firm ware to K3, the K3
went to unresponsive state with MCU LD on the LCD and the TX LED flashing.
This happened before. That time I was able to snap it from
Turn the P3 off while loading. Others have had the same problem. Not
sure why.
73,
matt W6NIA
On Fri, 23 Nov 2012 15:27:49 + (UTC), you wrote:
>Hello, all. I had a hard drive go down and got a new computer with Windows 8
>which is very cool. However, I am unable to download new firmware
Hello, all. I had a hard drive go down and got a new computer with Windows 8
which is very cool. However, I am unable to download new firmware to the K3
with the P3 connected and turned on like I was able to do with Windows XP.
Anyone else have this problem? 73, Steve W0SZ
_
er systems which can be a huge hassle.
>
> Bill
> K9YEQ
>
>
> -Original Message-
> From: elecraft-boun...@mailman.qth.net
> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Kok Chen
> Sent: Sunday, September 19, 2010 12:34 PM
> To: Elecraft Reflector
> Subject
mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Kok Chen
Sent: Sunday, September 19, 2010 12:34 PM
To: Elecraft Reflector
Subject: Re: [Elecraft] K3 :: firmware update failure
On Sep 19, 2010, at 9/199:47 AM, Bill K9YEQ wrote:
> I find the process simple and it works well for up
On Sep 19, 2010, at 9/199:47 AM, Bill K9YEQ wrote:
> I find the process simple and it works well for upgrading any of
> the K3 devices. The procedures for firmware updating both P3 and K3
> aren't fool proof.
While better but still not 100% foolproof, the Canon cameras that I
have can
Bill
K9YEQ
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Dick Dievendorff
Sent: Saturday, September 18, 2010 1:31 AM
To: 'The Smiths'; invento...@gmail.com; 'Elecraft Reflector'
Subject: Re: [Elecraft] K3 :: firmw
qth.net] On Behalf Of The Smiths
Sent: Friday, September 17, 2010 11:08 PM
To: invento...@gmail.com; Elecraft Reflector
Subject: Re: [Elecraft] K3 :: firmware update failure
Steve , you went through the same exact thing that I did. I had thought
that I missed a step, and then shut down too earl
load ALL button and everything
worked from there.
Give that a try and let me know if it doesn't work..I'm sure there's other ways
to skin this cat...
> Date: Fri, 17 Sep 2010 20:26:13 -0400
> From: invento...@gmail.com
> To: elecraft@mailman.qth.net
> Subject: [Elecraft
Situation resolved. Kudos, as always, to the vigilant and knowledgeable
guys monitoring this reflector.
For others who have a K3 / P3 setup, you may wish to familiarize yourself
with the bootloader operation and sequencing of the combined pair of units.
Had I not assumed I knew 100% how this work
Steve,
Are you using the latest K3 Utility? If not, download that first.
Then follow the instructions in the K3 Utility help file to force a K3
firmware load. You must unplug the power from the K3, not just cycle
with the power button.
If that does not work, perhaps Dick will help you.
73,
t: Friday, September 17, 2010 5:26 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 :: firmware update failure
I downloaded the new P3 utility and the latest firmware, plus the 4.12
release from the Elecraft server.
I've never had any problem on a firmware update, and the new load onto the
P3
I downloaded the new P3 utility and the latest firmware, plus the 4.12
release from the Elecraft server.
I've never had any problem on a firmware update, and the new load onto the
P3 worked just fine.
Then, I opened the K3 fw utility and proceeded to install the 4.12
revision.
First, a message p
"Dave & Jeanne Robertson"
Cc: "Dick Dievendorff" ; "Elecraft"
Sent: Saturday, April 03, 2010 6:15 PM
Subject: Re: [Elecraft] K3 Firmware Update.
Sorry, Dick
Plenty of others have had that "killed it by starting a browser"
experience, including myself. It WA
than anyone except
>> perhaps
>> Wayne and Lyle.
>>
>> Dick, K6KR
>>
>>
>> -Original Message-
>> From: elecraft-boun...@mailman.qth.net
>> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David Robertson
>> Sent: Saturday, April 0
27;" ;
Cc: "'Elecraft'"
Sent: Saturday, April 03, 2010 11:36 AM
Subject: RE: [Elecraft] K3 Firmware Update.
> There should be no data corruption caused by using other programs while
> the
> K3 Utility is sending firmware to the K3. Closing the K3 Utility during a
Dick Dievendorff wrote:
>
> There should be no data corruption caused by using other programs while
> the
> K3 Utility is sending firmware to the K3.
>
I hate to disagree with the author of the K3 Utility but the only time I
ever had a firmware update fail was when I was surfing with Firefox w
perhaps
Wayne and Lyle.
Dick, K6KR
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David Robertson
Sent: Saturday, April 03, 2010 5:54 AM
To: phys...@mac.com
Cc: Elecraft
Subject: [Elecraft] K3 Firmware Update.
Phil,
It is very
True, BUT - K3 Utility's Port tab contains a "Test Communications"
button that works very well to confirm that the computer is connected to
the K3 and the right port is selected on the computer.
Yes, HRD will do that verification too, but it is much more involved to
set up than K3 Utility. If
Phil,
It is very important that you be certain that whatever you use to get a RS232
connection from your computer to the K3 is good.
Running HRD (Ham Radio Deluxe) is a good test. Have your K3 set at the highest
baud rate it can do because that is what the K3 utility is going to use.
When upgr
Phil,
Download the latest K3 Utility and install it. Plug the computer to K3
serial connection in if you do not already have it connected. Turn on
your K3 and then open K3 Utility. It will now even create the "Local
Folder for the firmware files" if you choose not to specify one. Check
the
craft-boun...@mailman.qth.net] On Behalf Of Phil Hystad
Sent: Thursday, April 01, 2010 11:34 AM
To: Elecraft Reflector
Subject: [Elecraft] [K3] Firmware Update via K3 USB Utility
Gang,
I will be doing my very first K3 firmware update via the K3 USB Utility.
(I still need to download the latest versi
Gang,
I will be doing my very first K3 firmware update via the K3 USB Utility. (I
still need to download the latest version of the utility).
Is there anything I need to watch for or any stumbling blocks that are not
obvious? Any pointers or guidance is appreciated. If it is so trivially
sim
On 6 Jan 2010 at 21:24, Gary Smith wrote:
Out of curiosity I looked at some of the other tabs on the K3 utility
like configuration & calibration. All the buttons there were greyed
out. I went back to the Ports tab & deselected port 3 as mentioned
below & told it to select port 6 and then it rec
Hi,
I started the K3 utility and port 3 is connected at 38400 bps.
I just downloaded the most recent beta firmware, unzipped
k3fw3r68.rar, deleted the current filed from the beta folder, copied
the new files to the beta folder and assured it was the same folder
the utility was pointing at.
Wh
Just downloaded the latest K3 Beta firmware update (MCU 2.80 / DSP 1.99,
January 25, 2009)
A big thank you to Wayne/Eric et all for changing the CWT function:
CWT (CW TUNING AID) ON/OFF STATE SAVED: If you turn CWT on, it will
always turn on when you return to the applicable mode (e.g. CW).
The
Sometimes
the human brain works better than the best automated system I think.
Bruce-W8FU
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Steef PA2A
Sent: Thursday, July 10, 2008 9:54 AM
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] k3 firmware upd
t;[EMAIL PROTECTED]>
Sent: Thursday, July 10, 2008 8:03 AM
Subject: RE: [Elecraft] k3 firmware update.
Auto-Notch only works in SSB. In CW, NOTCH only works in MANUAL Tuning.
73 ---> Dave, W9ZRX
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behal
To: "PAUL VANOVEREN" <[EMAIL PROTECTED]>
> Cc:
> Sent: Thursday, July 10, 2008 3:14 AM
> Subject: Re: [Elecraft] k3 firmware update.
> >
> > PAUL VANOVEREN wrote on 07/ 9/08 06:03 PM:
> >> I am running the 2.02 version of the firmware, I believe there i
rmware and software is
not my favourite hobby
73 's Steef PA2A
k2 #4654
K3 #1184
- Original Message -
From: "Iain MacDonnell - K6IAM" <[EMAIL PROTECTED]>
To: "PAUL VANOVEREN" <[EMAIL PROTECTED]>
Cc:
Sent: Thursday, July 10, 2008 3:14 AM
Sub
PAUL VANOVEREN wrote on 07/ 9/08 06:03 PM:
I am running the 2.02 version of the firmware, I believe there is a released
version 2.10, plus two new Beta releases.2.13 and 2.15. ...when I go to the
utility and it lists 2.02 on the K3 and 2.02 as the available firmware for
update...did I miss
I am running the 2.02 version of the firmware, I believe there is a released
version 2.10, plus two new Beta releases.2.13 and 2.15. ...when I go to the
utility and it lists 2.02 on the K3 and 2.02 as the available firmware for
update...did I miss something ??
Paul NF8J
K3 758
>>* SSB TRANSMIT BANDPASS EXTENDED AT LOW END. Improvement
>> is about 2 dB at 300 Hz, 3 dB at 200 Hz, and 6 dB at 100 Hz.
>
> Can this be made optional? Excess LF response only wastes
> power at low frequencies and occupies excess bandwidth.
> We could add a menu entry for this -- it
hi Wayne,
On 4 May 2008 at 11:48, wayne burdick wrote:
> > Will TX EQ be made mode and/or input dependent? Setting TX EQ
> > for voice screws up the audio response for digital mode (AFSK A and
> > DATA A) operation. The same is true for RX EQ.
>
> I believe both RX and TX EQ are bypassed in DA
Joe Subich, W4TV wrote:
wider than necessary. With the FM filter, the 4.2 KHz high cut is
less than the 10 KHZ of IF bandwidth. Why is the IF bandwidth and
audio response excessively restricted with the FM filter? It should
be possible to achieve at least 12 KHz of IF bandwidth and 6 KHz or
Another thing that must be mentioned is that the improved QSK is a
treat... I just finished a qso under poor condx and even with levels
cranked up to hear a faint signal in QRN the QSK was very smooth -
even better than before. Since I use headphones I really appreciate
this.
Bob NW8L
On Sun, May
I noticed the exact same thing as Harrison, below! Auto-spot is broken.
But if I have to say something nice, NR works better (on SSB at least)
than it did before!
Windy
AI1V
Sun, 04 May 2008 20:00:52 -0700
Ditto here. While it wasn't "perfect" before, the new version often
over-shoots the
-
>
>> -Original Message-
>> From: [EMAIL PROTECTED] [mailto:elecraft-
>> [EMAIL PROTECTED] On Behalf Of Bob Cunnings
>> Sent: Sunday, May 04, 2008 7:17 PM
>> To: Elecraft Reflector
>> Subject: Re: [Elecraft] K3 FIRMWARE UPDATE: MCU 1.87, DSP 1.69
&
; From: [EMAIL PROTECTED] [mailto:elecraft-
> [EMAIL PROTECTED] On Behalf Of Bob Cunnings
> Sent: Sunday, May 04, 2008 7:17 PM
> To: Elecraft Reflector
> Subject: Re: [Elecraft] K3 FIRMWARE UPDATE: MCU 1.87, DSP 1.69
> (Finally!)
>
> I agree that auto-spot doesn'
This is great. With what other brand can you beat up on the
developers, and see the developers humbled by their own mistakes.
We understand Lyle. And I thought that was the sunset.
Stan Rife
W5EWA
Houston, TX
K2 SN 4216
K3 SN 0690
Lyle Johnson wrote:
...listening to the K3 on 29.600 F
After posting about my problem with not getting the dialled up power output
in DATA A mode, it occurred to me that perhaps it might be a good idea to
run the Low-Power (5W) Wattmeter Calibration. When I assembled my K3 I never
had to touch this adjustment because it produced 5W as accurate as I co
I agree that auto-spot doesn't seem as reliable as in earlier
versions. When I inject a continuous tone, it works fine, always
coming within a few Hz. For actual cw signals it now seems to be more
easily fooled, often tuning low - noticeably different to me, one who
uses the feature constantly. In
Joe Subich, W4TV-3 wrote:
>
>>* SSB TRANSMIT BANDPASS EXTENDED AT LOW END. Improvement
>> is about 2 dB at 300 Hz, 3 dB at 200 Hz, and 6 dB at 100 Hz.
>
> Can this be made optional? Excess LF response only wastes
> power at low frequencies and occupies excess bandwidth.
>
>> Additional
> >>* AUTO-SPOT (SPOT with CWT ON) now works with both very
> >> weak and very strong signals.
> >
> > Auto-spot consistently tunes to a tone 50 Hz low (50 Hz below
> > the value set for pitch).
>
> I can't duplicate this. I tried various sidetone pitches and
> found that auto-spot got to w
Bob Cunnings wrote:
>
> I have set up for PSK31 operation with the new firmware and am getting
> exactly what I expect. I'm using a peak reading external meter and it
> agrees with the power commanded and the power indicated on the K3
> front panel RF meter. First I adjusted audio drive to get 4
Can someone confirm the default file location for the K3 update utility when
updating through the Internet? Tnx!
- Original Message -
From: "Lyle Johnson" <[EMAIL PROTECTED]>
To: "G4ILO" <[EMAIL PROTECTED]>
Cc:
Sent: Sunday, May 04, 2008 2:47 PM
Sub
...listening to the K3 on 29.600 FM via my
FT-817 the audio sounds a bit distorted or "scratchy" on voice peaks which
suggests that the deviation is too high. I'd like to be able to adjust this
to see if it is or not.
If you see a dull red glow to the west, it is my face turning beet red.
Reas
* IF A 2.8 KHZ FILTER IS INSTALLED, SSB "NORM" BW is 2.8 kHz
(was fixed at 2.7 kHz).
Can this be extended to CW and Data? It appears that "NORM" is
currently fixed at 400 Hz regardless of mode and filter. 500 Hz
would be more appropriate for CW with the 500 Hz crystal filter
and even wider
G'day,
- Original Message -
From: "Joe Subich, W4TV" <[EMAIL PROTECTED]>
To: "'wayne burdick'" <[EMAIL PROTECTED]>; "'Elecraft Reflector'"
Sent: Sunday, May 04, 2008 1:24 PM
Subject: RE: [Elecraft] K3 FIRMWARE UPDATE: M
> MCU 1.87 / DSP 1.69, 5-3-08
>* AM RECEIVE WIDTH RANGE INCREASED: The WIDTH control in AM
> mode now has a range of 2.8 to 10.0 kHz. Wider settings provide
> outstanding fidelity for hi-fi speech and other wide-band signals.
> This is the *IF* filter bandwidth -- the traditional way to
I have set up for PSK31 operation with the new firmware and am getting
exactly what I expect. I'm using a peak reading external meter and it
agrees with the power commanded and the power indicated on the K3
front panel RF meter. First I adjusted audio drive to get 4 bars on
the ALC meter using a pu
Good day all,
I just uploaded the new firmware version which went smoothly.
After that I had to do some filter settings as I had my FM filter (yes, it
is in slot 1) already installed but it had to be enabled since the FM mode
is available now.
Normal procedure: go to Config, select a filter and
Does the advice for setting up soundcard digital modes given here:
http://www.mail-archive.com/elecraft@mailman.qth.net/msg53656.html
become effective when using this new version? Specifically:
"If you try and trick the system and run with *zero* ALC bars in
PSK31, the ALC has to work hard to g
The latest update is great, however I am curious as to when some of the more
basic functions such as squelch, keypad beep, and ESSB TX will be enabled. I
have also noticed that after the update, I can only listen out 4 KHz wide
versus the prior 6 KHz with the AM filter installed. Also why not allo
Bob Cunnings wrote:
>
> Does the advice for setting up soundcard digital modes given here:
>
> http://www.mail-archive.com/elecraft@mailman.qth.net/msg53656.html
>
> become effective when using this new version? Specifically:
>
> "If you try and trick the system and run with *zero* ALC bars i
the saved configuration.
Dick, K6KR
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of AD6XY - Mike
Sent: Sunday, May 04, 2008 3:42 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 FIRMWARE UPDATE: MCU 1.87, DSP 1.69 (Finally!)
Yes - Great. Install
hi Wayne,
Your new firmware is vy much appreciated and I am very happy with many
features though not everything tested yet.
The update went without a problem, congrats - this is very well done.
I have a peculiar behaviour with SSB modulation that I have to report:
wayne burdick schrieb am 3 May
Ian J Maude wrote:
>
> Secondly, what is the deviation set to in FM mode? For example, I would
> dearly love to use the rig on 2m for our local repeater via my XV-144
> but in the UK, that means narrow deviation. Could that be made
> adjustable if needed?
>
I don't have a transverter, so I'm
Yes - Great. Installed without problems. It does most of the things I have
been waiting for. Still not interfacing to the kettle but you can't have
everything
Is there a utility to allow me to upload a set of settings so I don't have
to go through all the config? I know I can backup and resto
Ian J Maude wrote:
>
> Great stuff Wayne, thanks!
> One point and a question. Firstly, the RPT OFS menu entry is not in the
> config menu, it is in the main one :-)
>
> Secondly, what is the deviation set to in FM mode? For example, I would
> dearly love to use the rig on 2m for our local rep
Does the advice for setting up soundcard digital modes given here:
http://www.mail-archive.com/elecraft@mailman.qth.net/msg53656.html
become effective when using this new version? Specifically:
"If you try and trick the system and run with *zero* ALC bars in
PSK31, the ALC has to work hard to gi
wayne burdick wrote:
We've just completed the most extensive K3 firmware update ever. The
full list of changes is provided below.
Great stuff Wayne, thanks!
One point and a question. Firstly, the RPT OFS menu entry is not in the
config menu, it is in the main one :-)
Secondly, what is the dev
The SSB transmit chain has had a major rework. The
results are very impressive.
1. The ALC is vastly improved. In fact you could say
that the K3's ALC is perfect because it does not
contribute any measurable levels of IMD to the SSB
signal.
2. The increase in IMD levels when you turn on the
sp
Thanks David, that did it!
I'm sure the previous times I did PORT menu it didn't show usbserial.
Tomorrow, I'll try the new brain.
73,
Windy
On May 3, 2008, at 9:31 PM, David Fleming wrote:
Hi Windy,
It sounds like you're trying to communicate with a
modem or a bluetooth device. The KUSB
Hi Windy,
It sounds like you're trying to communicate with a
modem or a bluetooth device. The KUSB will appear as
"usbserial" in the Port menu. Be sure you are
selecting "usbserial" as your port.
The Filter Configuration is still under development
and not yet functional in the Mac and Linux ver
System: Mac OSX 10.5.2.
I have the KUSB adapter cable.
I downloaded AND installed the appropriate Prolific driver for my OS,
as instructed (PL2303 driver). Installation looked normal. I
restarted, etc.
I have K3 Utility v. 1.1.4.1
K3 is turned on, connected to USB port.
Port -- after Refre
Mark,
Any version of 1.1.4.1 *or above* may be used.
73,
Don W3FPR
mark roz wrote:
utility rev. shows 1.1.4.8
why?
Thanks,
MARK
--- On Sat, 5/3/08, wayne burdick <[EMAIL PROTECTED]> wrote:
From: wayne burdick <[EMAIL PROTECTED]>
Subject: [Elecraft] K3 FIRMWARE UPDATE: M
utility rev. shows 1.1.4.8
why?
Thanks,
MARK
--- On Sat, 5/3/08, wayne burdick <[EMAIL PROTECTED]> wrote:
> From: wayne burdick <[EMAIL PROTECTED]>
> Subject: [Elecraft] K3 FIRMWARE UPDATE: MCU 1.87, DSP 1.69 (Finally!)
> To: "Elecraft Reflector"
> Da
- Original Message -
From: "wayne burdick" <[EMAIL PROTECTED]>
To: "Elecraft Reflector"
Sent: Saturday, May 03, 2008 8:29 PM
Subject: [Elecraft] K3 FIRMWARE UPDATE: MCU 1.87, DSP 1.69 (Finally!)
We've just completed the most extensive K3 firmware update e
To Aptos,
As a six meter operator, all I can say is thank you...thank you
...thank you...
This mode is s useful on VHF and above.
Now, for my second K3 to arrive for my six meter SSB/CW remote base!
tom K8TB K3's # 53 & ?
wayne burdick wrote:
>We've just completed the most
Wow, totally outstanding, Wayne. Congratulations on this major milestone!
Can't wait to see how it works. Looks like my K3 will have this revision
loaded in it when shipped, then.
Bill W5WVO
wayne burdick wrote:
We've just completed the most extensive K3 firmware update ever. The
full list of
We've just completed the most extensive K3 firmware update ever. The
full list of changes is provided below.
*** NOTE *** You must use the latest version of our firmware loader
(K3 Utility rev 1.1.4.1) or else you won't be able to load all
components of the upgrade. It's available on our K3 s
Within a week.
73, Eric
Mike N8XPQ wrote:
Anyone have any idea how far out we are on the next badly needed firmware
update?
-
Mike Koetje N8XPQ
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to th
Anyone have any idea how far out we are on the next badly needed firmware
update?
-
Mike Koetje N8XPQ
--
View this message in context:
http://www.nabble.com/K3-firmware-update-tp16992743p16992743.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Hi all,
In MCU revision 1.77, SPOT wasn't working within the REF CAL menu
entry. Sorry about that! Revision 1.78 corrects this and is now
available.
73,
Wayne
N6KR
---
http://www.elecraft.com
___
Elecraft mailing list
Post to: Elecraft@mailman.q
Brett Howard said:
Poof! As much as K3 owners have been having fun with the new Elecraft
invented mode of CW to RTTY now there is yet another new mode in amateur
radio!
CW-to-RTTY isn't new - the AEA MBA-RC was
able to convert CW to Baudot & ASCII RTTY &
vice versa. Not sure, there may have
Poof! As much as K3 owners have been having fun with the new Elecraft
invented mode of CW to RTTY now there is yet another new mode in amateur
radio!
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the lis
We've just posted a new revision of K3 firmware on our web site (both
MCU and DSP). Please see the release notes below.
73,
Wayne
N6KR
* * *
MCU 1.68 and DSP 1.53, 2-17-08
* MIC Source is now saved independently for voice and data modes. For
example, you
could set MAIN:MIC SEL set to L
David Ferrington, M0XDF wrote:
I meant a Tap to start tune, currently its a HOLD to start tune, followed by
a TAP to stop - yeah, ok, its a matter of a second.
Personally, I would prefer to hold the tune button, that way I cannot
put it into actual tx by accident. Xmit will only actually sen
I meant a Tap to start tune, currently its a HOLD to start tune, followed by
a TAP to stop - yeah, ok, its a matter of a second.
On 30/1/08 17:45, "G4ILO" <[EMAIL PROTECTED]> sent:
>
>
> M0XDF wrote:
>>
>> Not to look a gift horse in the mouth, but at some point, it might be nice
>> to be ab
M0XDF wrote:
>
> Not to look a gift horse in the mouth, but at some point, it might be nice
> to be able to tune with a button tap instead of a press - I don't use
> [XMIT] at all, but do use [TUNE] a lot, I'd like to be able to swap the
> function.
I think that might be hard to achive, becaus
I used it the other day when I had a cheap headset with no PTT button
and was mobile (parked).
Leigh/WA5ZNU
David Ferrington, M0XDF wrote:
As a matter of curiosity, what do people use [XMIT] for?
___
Elecraft mailing list
Post to: Elecraft@mailma
When Wayne works on the next revision this is one of the items likely to be
considered. It is high on our list.
-
73,
Greg - AB7R
Whidbey Island WA
NA-065
K3#0009
On Wed Jan 30 7:15 , G4ILO sent:
>
>
>Dick Dievendorff wrote:
>>
>> I find the TUN PWR menu option avail
Not to look a gift horse in the mouth, but at some point, it might be nice
to be able to tune with a button tap instead of a press - I don't use
[XMIT] at all, but do use [TUNE] a lot, I'd like to be able to swap the
function.
As a matter of curiosity, what do people use [XMIT] for?
On 30/1/0
Dick Dievendorff wrote:
>
> I find the TUN PWR menu option available if I have CONFIG:TECH MD on and
> absent if I have CONFIG:TECH MD off.
>
Yes. I didn't expect it to be buried in there, but I guess I won't really
need to change it that often. Now all I need is for the ATU in/out setting
to b
---
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Don Ehrlich
Sent: Tuesday, January 29, 2008 7:44 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 Firmware Update
Have downloaded 1.65 / 1.52 and cannot find the Menu item for setting Tune
power (TUN PWR) as advertized in t
Subject: [Elecraft] K3 Firmware Update
Have downloaded 1.65 / 1.52 and cannot find the Menu item for setting Tune
power (TUN PWR) as advertized in the release notes.
Don K7FJ
K3 195
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be
Have downloaded 1.65 / 1.52 and cannot find the Menu item for setting Tune
power (TUN PWR) as advertized in the release notes.
Don K7FJ
K3 195
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list
Yes, Don Argo is very responsive--love MacLoggerDX. I'd also have to mention
John Henry
at Ten Tec for is his great firmware support with the Omni VII.
I can't wait to get my K3 so I can fully appreciate Wayne and the super
service he and Elecraft provide. But it will be months unfortunately.
For the first time in my radio career, I have a fast internet connection
co-located with my rig. I just used the K3 updater to install the current
firmware and the process was amazingly smooth and fast. The software
checked for an update, found one, downloaded it and then sent it to the rig.
The
On Tuesday 29 January 2008 02:00:00 pm David Ferrington, M0XDF wrote:
> Great, there is only one other company that I have experience of, that
> responds in this way, and that is DogPark Software who wrote MacLoggerDX.
I had an email answer from an engineer at SGC within an hour of
sending a que
Great, there is only one other company that I have experience of, that
responds in this way, and that is DogPark Software who wrote MacLoggerDX.
Wonderful service Wayne.
Tune Power - greatly desired, thank you.
Mode Switch - really good button press saver :)
Installed via Mac software, no probl
We've released a new revision of K3 firmware (both MCU and DSP). Please
see the release notes below.
73,
Wayne
N6KR
* * *
MCU 1.65 and DSP 1.52, 1-27-08
* TUNE POWER level menu entry added (TUN PWR). This determines the
power level used
when the TUNE switch is pressed. The default, "NO
.g., CONFIG:FLx BW).
To use the FIR (new) filters, tap '7' until you see
"IIR OFF". This is now the default for newly-shipped
K3s.
----------
[Elecraft] K3 Firmware Update
wayne burdick n6kr at elecraft.com
Fri Jan 11 12:56:35 EST 2008
1 - 100 of 124 matches
Mail list logo
