...mikrotik POS? Piece of Salmon, point of sale, phaser on stun??? On May 15, 2016 7:34 AM, "Gino Villarini" <ginovi...@gmail.com> wrote:
> faisal, thanks. I read this today, but we already fixed the issue by > replacing the mikrotik POS with a Juniper SRX100 unit... problem solved! > > Thanks to all! > > On Fri, May 13, 2016 at 9:25 AM, Faisal Imtiaz <fai...@snappytelecom.net> > wrote: > >> Which model CCR are you using ? >> Pay attention to the ports you are using on that CCR due to how they are >> connected to the switch chip/CPU. >> e.g. on CCR 1008, don't use the 1st 4 ports (they are all on a switch >> chip with a 1g connection to the CPU, so with nat the packets can be >> hitting the CPU multiple times... >> >> if that does not work... then ......Just for kicks.... try the following:- >> >> Do the tests with one change at a time. >> -------------------- >> make sure you are on the latest 6.35.2 ROS and routerboard firmware is up >> to date. >> >> 1) Turn off connection tracking. >> >> 2) change the interface queue to multi-queue- ethernet (reboot required) >> >> 3) make sure flow control on the ports to the Radio are on. >> >> 4) put a simple queue for the desired BW on the CCR. >> ------------------- >> >> Regards. >> >> Faisal Imtiaz >> Snappy Internet & Telecom >> 7266 SW 48 Street >> Miami, FL 33155 >> Tel: 305 663 5518 x 232 >> >> Help-desk: (305)663-5518 Option 2 or Email: supp...@snappytelecom.net >> >> ------------------------------ >> >> *From: *"Gino Villarini" <ginovi...@gmail.com> >> *To: *"Animal Farm" <af@afmug.com> >> *Sent: *Friday, May 13, 2016 9:01:22 AM >> *Subject: *Re: [AFMUG] Odd issue - Mimosa B11 and Mikrotik >> >> yes, using fiber, same issue >> >> On Thu, May 12, 2016 at 4:35 PM, can...@believewireless.net < >> p...@believewireless.net> wrote: >> >>> Did you check for duplex mismatch? >>> >>> On Thu, May 12, 2016 at 3:51 PM, Gino Villarini <ginovi...@gmail.com> >>> wrote: >>> >>>> laptop direct to mimosa has no issue >>>> >>>> Get Outlook for iOS <https://aka.ms/o0ukef> >>>> >>>> >>>> >>>> >>>> On Thu, May 12, 2016 at 12:47 PM -0700, "Jason Wilson" < >>>> ja...@remotelylocated.com> wrote: >>>> >>>> Rory had that issue with SME if the mimosa ptmp the CPU in the laptop >>>>> was maxing out. >>>>> On May 12, 2016 11:39 AM, "Josh Reynolds" <j...@kyneticwifi.com> >>>>> wrote: >>>>> >>>>>> http://wiki.mikrotik.com/wiki/Manual:Wiki/Fasttrack#Description >>>>>> >>>>>> >>>>>> On Thu, May 12, 2016 at 1:37 PM, Josh Reynolds <j...@kyneticwifi.com> >>>>>> wrote: >>>>>> > I don't know much about the CCRs. Do they have FastPath and >>>>>> FastTrack >>>>>> > enabled by default? >>>>>> > >>>>>> > On Thu, May 12, 2016 at 1:33 PM, Gino Villarini < >>>>>> ginovi...@gmail.com> wrote: >>>>>> >> no >>>>>> >> >>>>>> >> simple config, static ip on the wan, private ip on lan, nat >>>>>> >> >>>>>> >> On Thu, May 12, 2016 at 2:30 PM, Josh Reynolds < >>>>>> j...@kyneticwifi.com> wrote: >>>>>> >>> >>>>>> >>> Did you copy the config from one CCR to the other? >>>>>> >>> >>>>>> >>> On Thu, May 12, 2016 at 1:24 PM, Gino Villarini < >>>>>> ginovi...@gmail.com> >>>>>> >>> wrote: >>>>>> >>> > Got a customer with a dedicated pipe, 250 Mbps >>>>>> >>> > >>>>>> >>> > Mimosa B11 to a CCR >>>>>> >>> > >>>>>> >>> > BW test from the CCR to our head router provides the BW no >>>>>> problem. >>>>>> >>> > >>>>>> >>> > But Laptop (capable) behind CCR in NAT mode, throughput dies at >>>>>> about >>>>>> >>> > 120 >>>>>> >>> > Mbps >>>>>> >>> > >>>>>> >>> > Changed routers, same issue >>>>>> >>> > >>>>>> >>> > Any ideas? >>>>>> >> >>>>>> >> >>>>>> >>>>> >>> >> >
