hehe.. yes I know.. I guess these are the nuances between Cuban Spanish / Puerto Rican Spanish and Mexican Spanish... There was another Cuban Spanish phrase I could have used, but it would not have been appropriate for the list :)
All of them are terms of endearment ! (not ! ) :) Faisal Imtiaz Snappy Internet & Telecom 7266 SW 48 Street Miami, FL 33155 Tel: 305 663 5518 x 232 Help-desk: (305)663-5518 Option 2 or Email: [email protected] > From: "Jaime Solorza" <[email protected]> > To: "Animal Farm" <[email protected]> > Sent: Sunday, May 15, 2016 11:08:41 AM > Subject: Re: [AFMUG] Odd issue - Mimosa B11 and Mikrotik > Careful!!!!....como...can also be " I eat".... ...here is a better > translation... "mikrotik vale madre......" > On May 15, 2016 8:53 AM, "Faisal Imtiaz" < [email protected] > wrote: >> loose translation .... 'como mierada' ! >> :) >> Faisal Imtiaz >> Snappy Internet & Telecom >> 7266 SW 48 Street >> Miami, FL 33155 >> Tel: 305 663 5518 x 232 >> Help-desk: (305)663-5518 Option 2 or Email: [email protected] >>> From: "Jaime Solorza" < [email protected] > >>> To: "Animal Farm" < [email protected] > >>> Sent: Sunday, May 15, 2016 10:36:02 AM >>> Subject: Re: [AFMUG] Odd issue - Mimosa B11 and Mikrotik >>> ...mikrotik POS? Piece of Salmon, point of sale, phaser on stun??? >>> On May 15, 2016 7:34 AM, "Gino Villarini" < [email protected] > wrote: >>>> faisal, thanks. I read this today, but we already fixed the issue by >>>> replacing >>>> the mikrotik POS with a Juniper SRX100 unit... problem solved! >>>> Thanks to all! >>>> On Fri, May 13, 2016 at 9:25 AM, Faisal Imtiaz < [email protected] > >>>> wrote: >>>>> Which model CCR are you using ? >>>>> Pay attention to the ports you are using on that CCR due to how they are >>>>> connected to the switch chip/CPU. >>>>> e.g. on CCR 1008, don't use the 1st 4 ports (they are all on a switch >>>>> chip with >>>>> a 1g connection to the CPU, so with nat the packets can be hitting the CPU >>>>> multiple times... >>>>> if that does not work... then ......Just for kicks.... try the following:- >>>>> Do the tests with one change at a time. >>>>> -------------------- >>>>> make sure you are on the latest 6.35.2 ROS and routerboard firmware is up >>>>> to >>>>> date. >>>>> 1) Turn off connection tracking. >>>>> 2) change the interface queue to multi-queue- ethernet (reboot required) >>>>> 3) make sure flow control on the ports to the Radio are on. >>>>> 4) put a simple queue for the desired BW on the CCR. >>>>> ------------------- >>>>> Regards. >>>>> Faisal Imtiaz >>>>> Snappy Internet & Telecom >>>>> 7266 SW 48 Street >>>>> Miami, FL 33155 >>>>> Tel: 305 663 5518 x 232 >>>>> Help-desk: (305)663-5518 Option 2 or Email: [email protected] >>>>>> From: "Gino Villarini" < [email protected] > >>>>>> To: "Animal Farm" < [email protected] > >>>>>> Sent: Friday, May 13, 2016 9:01:22 AM >>>>>> Subject: Re: [AFMUG] Odd issue - Mimosa B11 and Mikrotik >>>>>> yes, using fiber, same issue >>>>>> On Thu, May 12, 2016 at 4:35 PM, [email protected] < >>>>>> [email protected] > wrote: >>>>>>> Did you check for duplex mismatch? >>>>>>> On Thu, May 12, 2016 at 3:51 PM, Gino Villarini < [email protected] > >>>>>>> wrote: >>>>>>>> laptop direct to mimosa has no issue >>>>>>>> Get Outlook for iOS >>>>>>>> On Thu, May 12, 2016 at 12:47 PM -0700, "Jason Wilson" < >>>>>>>> [email protected] > wrote: >>>>>>>>> Rory had that issue with SME if the mimosa ptmp the CPU in the laptop >>>>>>>>> was maxing >>>>>>>>> out. >>>>>>>>> On May 12, 2016 11:39 AM, "Josh Reynolds" < [email protected] > >>>>>>>>> wrote: >>>>>>>>>> http://wiki.mikrotik.com/wiki/Manual:Wiki/Fasttrack#Description >>>>>>>>>> On Thu, May 12, 2016 at 1:37 PM, Josh Reynolds < >>>>>>>>>> [email protected] > wrote: >>>>>>>>>> > I don't know much about the CCRs. Do they have FastPath and >>>>>>>>>> > FastTrack >>>>>>>>>> > enabled by default? >>>>>>>>>> > On Thu, May 12, 2016 at 1:33 PM, Gino Villarini < >>>>>>>>>> > [email protected] > wrote: >>>>>>>>>> >> no >>>>>>>>>> >> simple config, static ip on the wan, private ip on lan, nat >>>>>>>>>> >> On Thu, May 12, 2016 at 2:30 PM, Josh Reynolds < >>>>>>>>>> >> [email protected] > wrote: >>>>>>>>>> >>> Did you copy the config from one CCR to the other? >>>>>>>>>> >>> On Thu, May 12, 2016 at 1:24 PM, Gino Villarini < >>>>>>>>>> >>> [email protected] > >>>>>>>>>> >>> wrote: >>>>>>>>>> >>> > Got a customer with a dedicated pipe, 250 Mbps >>>>>>>>>> >>> > Mimosa B11 to a CCR >>>>>>>>>> >>> > BW test from the CCR to our head router provides the BW no >>>>>>>>>> >>> > problem. >>>>>>>>>> >>> > But Laptop (capable) behind CCR in NAT mode, throughput dies >>>>>>>>>> >>> > at about >>>>>>>>>> >>> > 120 >>>>>>>>>> >>> > Mbps >>>>>>>>>> >>> > Changed routers, same issue >>>>>>>>>> >>> > Any ideas?
