loose translation .... 'como mierada' ! :)
Faisal Imtiaz Snappy Internet & Telecom 7266 SW 48 Street Miami, FL 33155 Tel: 305 663 5518 x 232 Help-desk: (305)663-5518 Option 2 or Email: [email protected] > From: "Jaime Solorza" <[email protected]> > To: "Animal Farm" <[email protected]> > Sent: Sunday, May 15, 2016 10:36:02 AM > Subject: Re: [AFMUG] Odd issue - Mimosa B11 and Mikrotik > ...mikrotik POS? Piece of Salmon, point of sale, phaser on stun??? > On May 15, 2016 7:34 AM, "Gino Villarini" < [email protected] > wrote: >> faisal, thanks. I read this today, but we already fixed the issue by >> replacing >> the mikrotik POS with a Juniper SRX100 unit... problem solved! >> Thanks to all! >> On Fri, May 13, 2016 at 9:25 AM, Faisal Imtiaz < [email protected] > >> wrote: >>> Which model CCR are you using ? >>> Pay attention to the ports you are using on that CCR due to how they are >>> connected to the switch chip/CPU. >>> e.g. on CCR 1008, don't use the 1st 4 ports (they are all on a switch chip >>> with >>> a 1g connection to the CPU, so with nat the packets can be hitting the CPU >>> multiple times... >>> if that does not work... then ......Just for kicks.... try the following:- >>> Do the tests with one change at a time. >>> -------------------- >>> make sure you are on the latest 6.35.2 ROS and routerboard firmware is up to >>> date. >>> 1) Turn off connection tracking. >>> 2) change the interface queue to multi-queue- ethernet (reboot required) >>> 3) make sure flow control on the ports to the Radio are on. >>> 4) put a simple queue for the desired BW on the CCR. >>> ------------------- >>> Regards. >>> Faisal Imtiaz >>> Snappy Internet & Telecom >>> 7266 SW 48 Street >>> Miami, FL 33155 >>> Tel: 305 663 5518 x 232 >>> Help-desk: (305)663-5518 Option 2 or Email: [email protected] >>>> From: "Gino Villarini" < [email protected] > >>>> To: "Animal Farm" < [email protected] > >>>> Sent: Friday, May 13, 2016 9:01:22 AM >>>> Subject: Re: [AFMUG] Odd issue - Mimosa B11 and Mikrotik >>>> yes, using fiber, same issue >>>> On Thu, May 12, 2016 at 4:35 PM, [email protected] < >>>> [email protected] > wrote: >>>>> Did you check for duplex mismatch? >>>>> On Thu, May 12, 2016 at 3:51 PM, Gino Villarini < [email protected] > >>>>> wrote: >>>>>> laptop direct to mimosa has no issue >>>>>> Get Outlook for iOS >>>>>> On Thu, May 12, 2016 at 12:47 PM -0700, "Jason Wilson" < >>>>>> [email protected] > wrote: >>>>>>> Rory had that issue with SME if the mimosa ptmp the CPU in the laptop >>>>>>> was maxing >>>>>>> out. >>>>>>> On May 12, 2016 11:39 AM, "Josh Reynolds" < [email protected] > >>>>>>> wrote: >>>>>>>> http://wiki.mikrotik.com/wiki/Manual:Wiki/Fasttrack#Description >>>>>>>> On Thu, May 12, 2016 at 1:37 PM, Josh Reynolds < [email protected] >>>>>>>> > wrote: >>>>>>>> > I don't know much about the CCRs. Do they have FastPath and FastTrack >>>>>>>> > enabled by default? >>>>>>>> > On Thu, May 12, 2016 at 1:33 PM, Gino Villarini < >>>>>>>> > [email protected] > wrote: >>>>>>>> >> no >>>>>>>> >> simple config, static ip on the wan, private ip on lan, nat >>>>>>>> >> On Thu, May 12, 2016 at 2:30 PM, Josh Reynolds < >>>>>>>> >> [email protected] > wrote: >>>>>>>> >>> Did you copy the config from one CCR to the other? >>>>>>>> >>> On Thu, May 12, 2016 at 1:24 PM, Gino Villarini < >>>>>>>> >>> [email protected] > >>>>>>>> >>> wrote: >>>>>>>> >>> > Got a customer with a dedicated pipe, 250 Mbps >>>>>>>> >>> > Mimosa B11 to a CCR >>>>>>>> >>> > BW test from the CCR to our head router provides the BW no >>>>>>>> >>> > problem. >>>>>>>> >>> > But Laptop (capable) behind CCR in NAT mode, throughput dies at >>>>>>>> >>> > about >>>>>>>> >>> > 120 >>>>>>>> >>> > Mbps >>>>>>>> >>> > Changed routers, same issue >>>>>>>> >>> > Any ideas?
