Careful!!!!....como...can also be " I eat".... ...here is a better translation... "mikrotik vale madre......" On May 15, 2016 8:53 AM, "Faisal Imtiaz" <[email protected]> wrote:
> loose translation .... 'como mierada' ! > > > :) > > Faisal Imtiaz > Snappy Internet & Telecom > 7266 SW 48 Street > Miami, FL 33155 > Tel: 305 663 5518 x 232 > > Help-desk: (305)663-5518 Option 2 or Email: [email protected] > > ------------------------------ > > *From: *"Jaime Solorza" <[email protected]> > *To: *"Animal Farm" <[email protected]> > *Sent: *Sunday, May 15, 2016 10:36:02 AM > *Subject: *Re: [AFMUG] Odd issue - Mimosa B11 and Mikrotik > > ...mikrotik POS? Piece of Salmon, point of sale, phaser on stun??? > On May 15, 2016 7:34 AM, "Gino Villarini" <[email protected]> wrote: > >> faisal, thanks. I read this today, but we already fixed the issue by >> replacing the mikrotik POS with a Juniper SRX100 unit... problem solved! >> Thanks to all! >> >> On Fri, May 13, 2016 at 9:25 AM, Faisal Imtiaz <[email protected]> >> wrote: >> >>> Which model CCR are you using ? >>> Pay attention to the ports you are using on that CCR due to how they are >>> connected to the switch chip/CPU. >>> e.g. on CCR 1008, don't use the 1st 4 ports (they are all on a switch >>> chip with a 1g connection to the CPU, so with nat the packets can be >>> hitting the CPU multiple times... >>> >>> if that does not work... then ......Just for kicks.... try the >>> following:- >>> >>> Do the tests with one change at a time. >>> -------------------- >>> make sure you are on the latest 6.35.2 ROS and routerboard firmware is >>> up to date. >>> >>> 1) Turn off connection tracking. >>> >>> 2) change the interface queue to multi-queue- ethernet (reboot >>> required) >>> >>> 3) make sure flow control on the ports to the Radio are on. >>> >>> 4) put a simple queue for the desired BW on the CCR. >>> ------------------- >>> >>> Regards. >>> >>> Faisal Imtiaz >>> Snappy Internet & Telecom >>> 7266 SW 48 Street >>> Miami, FL 33155 >>> Tel: 305 663 5518 x 232 >>> >>> Help-desk: (305)663-5518 Option 2 or Email: [email protected] >>> >>> ------------------------------ >>> >>> *From: *"Gino Villarini" <[email protected]> >>> *To: *"Animal Farm" <[email protected]> >>> *Sent: *Friday, May 13, 2016 9:01:22 AM >>> *Subject: *Re: [AFMUG] Odd issue - Mimosa B11 and Mikrotik >>> >>> yes, using fiber, same issue >>> >>> On Thu, May 12, 2016 at 4:35 PM, [email protected] < >>> [email protected]> wrote: >>> >>>> Did you check for duplex mismatch? >>>> >>>> On Thu, May 12, 2016 at 3:51 PM, Gino Villarini <[email protected]> >>>> wrote: >>>> >>>>> laptop direct to mimosa has no issue >>>>> >>>>> Get Outlook for iOS <https://aka.ms/o0ukef> >>>>> >>>>> >>>>> >>>>> >>>>> On Thu, May 12, 2016 at 12:47 PM -0700, "Jason Wilson" < >>>>> [email protected]> wrote: >>>>> >>>>> Rory had that issue with SME if the mimosa ptmp the CPU in the laptop >>>>>> was maxing out. >>>>>> On May 12, 2016 11:39 AM, "Josh Reynolds" <[email protected]> >>>>>> wrote: >>>>>> >>>>>>> http://wiki.mikrotik.com/wiki/Manual:Wiki/Fasttrack#Description >>>>>>> >>>>>>> >>>>>>> On Thu, May 12, 2016 at 1:37 PM, Josh Reynolds <[email protected]> >>>>>>> wrote: >>>>>>> > I don't know much about the CCRs. Do they have FastPath and >>>>>>> FastTrack >>>>>>> > enabled by default? >>>>>>> > >>>>>>> > On Thu, May 12, 2016 at 1:33 PM, Gino Villarini < >>>>>>> [email protected]> wrote: >>>>>>> >> no >>>>>>> >> >>>>>>> >> simple config, static ip on the wan, private ip on lan, nat >>>>>>> >> >>>>>>> >> On Thu, May 12, 2016 at 2:30 PM, Josh Reynolds < >>>>>>> [email protected]> wrote: >>>>>>> >>> >>>>>>> >>> Did you copy the config from one CCR to the other? >>>>>>> >>> >>>>>>> >>> On Thu, May 12, 2016 at 1:24 PM, Gino Villarini < >>>>>>> [email protected]> >>>>>>> >>> wrote: >>>>>>> >>> > Got a customer with a dedicated pipe, 250 Mbps >>>>>>> >>> > >>>>>>> >>> > Mimosa B11 to a CCR >>>>>>> >>> > >>>>>>> >>> > BW test from the CCR to our head router provides the BW no >>>>>>> problem. >>>>>>> >>> > >>>>>>> >>> > But Laptop (capable) behind CCR in NAT mode, throughput dies >>>>>>> at about >>>>>>> >>> > 120 >>>>>>> >>> > Mbps >>>>>>> >>> > >>>>>>> >>> > Changed routers, same issue >>>>>>> >>> > >>>>>>> >>> > Any ideas? >>>>>>> >> >>>>>>> >> >>>>>>> >>>>>> >>>> >>> >> >
