Hi there,
I have tried the recommendations made and it still doesn't work. As
mentioned previously I get the following error at start-up:
> %SYS-4-CONFIG_NEWER: Configurations from version 12.0 may not be correctly
> under stood.
I have tried the "write mem" and "reload" commands after upgradi
Hi, Cisco Fans,
I have a question, could you have a look and if you could give me a reply,
that will be much better.
Following is:
Subject:
I want my LAN use Cisco2610__WIC-2A/S port to dial up to the Internet
*
In the book, hub subinterface is specified as point-to-point, by befault
point-to-point subinterface has OSPF network type point-to-point.
However, on the spokes, subinterface's type is not define explicitly, which
is not possible. After I enable encapsulation frame-relay on physical
interface, i
We have about 40 procurves with one cat5 almost never had problems.
As long as you do not intend to deploy some thing which is cisco's
pripotary,
u will befine. Procureve supports standard VLANs, stacking etc...and
relativley cheap.
Procurve also come with free HPTop Tools which will let u manager
Haven't distribute-lists for BGP been made obsolete by prefix-lists?
Regards,
Em
- Original Message -
From: suaveguru <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Friday, December 08, 2000 5:26 PM
Subject: distribute list problem
> Hi,
>
> I have already configured BGP for but o
first thing is does your internal routing protocol know where it is?
-Original Message-
From: suaveguru [mailto:[EMAIL PROTECTED]]
Sent: 08 December 2000 06:27
To: [EMAIL PROTECTED]
Subject: distribute list problem
Hi,
I have already configured BGP for but our trafiic for
IP
Address
Hi All,
I have one Catalys 1900 with Firmware 1.09, but I forgot the password. The
Cisco Documetation said that I need Password Recovery Utility software to
recovery Password. I logon to CCO and follow the link in document, but I can
not download Password Recovery Utility.
Where Can I download Pas
Hi Ash
The message you get is not an error it is just telling you that the
config was created by a version 12 and the boot system is a version 11.
This is just to let you know that if the image from version 12 is not
loaded then all of the commands may no work correctly.
With the bootup
This is my answer :
CCSE- Certified Checkpoint Systems Engineer
CCNE- Center for Continuing Nursing Education
CCSI- Certified Cisco Systems Instructors
Rgds,
Sam
> -Original Message-
> From: Ravi Kumar [SMTP:[EMAIL PROTECTED]]
> Sent: Friday, December 08,
Group,
Sorry for the off subject, but I am in desperate need of the ICND and
Network+, Power Point presentations! Can anybody help?
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct
Install to default location. That will solve your problem.
Pierre
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Hook Soso
Sent: Friday, December 08, 2000 12:34 AM
To: [EMAIL PROTECTED]
Subject: problem of documentation cd
I try to install Cisco Docum
he's got no synchronization, so it doesn't *need* to be in the internal
routing protocol does it?
Em
- Original Message -
From: McCallum, Robert <[EMAIL PROTECTED]>
To: 'suaveguru' <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]>
Sent: Friday, December 08, 2000 8:07 PM
Subject: RE: distribute l
Hi Nandit,
Answer to this question took me quite a lot of time and research to find out
when I first got interested in Cisco and wanted to build a home lab for
practice.
I don't believe there is a right or wrong way in building a lab at home for
practice as there is quite a selection of Cisco ha
oh boy, where did you hear these terms. overheard
in office ?
well here you go...
CCSE Checkpoint certified systems engineer
CCNA Cisco certified network associate
CCSI cisco certified systems instructor (not sure
about this one)
--- Ravi Kumar <[EMAIL PROTECTED]> wrote:
> dear friends
>
> I
Until you upgrade your bootrom to 12.0 (from 11.0) you will always get that
message.
Or, you could always go back to an 11.?? IOS version. ;)
Brad Stanfield
Network/Integration Engineer
[EMAIL PROTECTED]
Government Micro Res
Shameless plug...
www.thetestpage.net is having a new years special on the downloadable test
engine.
Only $30 for 1019 questions covering CCDA, CCDP, BCRAN, Support 2.0, CCIE
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
R
All,
Passed Switching 2.0 (890)=20
Used - Own practical knowledge, CLSC notes, Boson Tests.
The Boson tests are a lot harder than the real thing - but are very =
good, all the same.
Some questions were a bit tricky but if you read them carefully and =
eliminate silly answers it should be ok.
K
please refer a good book for CCIE R&S exam ?
how is the Giles book ?
__
Do You Yahoo!?
Yahoo! Shopping - Thousands of Stores. Millions of Products.
http://shopping.yahoo.com/
_
FAQ, list archives, and subscription i
you connect them however you need to for a given scenerio. A lab doesn't
have to be setup in fixed configuration, so you could use the crossover
serial between say the 2501 and 2503, and again between the 2503 and
2504.then you could plug both 2501 an 2503 into a hub, and then
with 2 nt
Follow the link on this page:
http://www.cisco.com/warp/public/474/index.shtml
You don't have to use the utility to do it.
""Ngo Van Dzung"" <[EMAIL PROTECTED]> wrote in message
001c01c060f7$05d0c310$0b65a8c0@ngodzung2000">news:001c01c060f7$05d0c310$0b65a8c0@ngodzung2000...
> Hi All,
> I have on
Pinging does not verify name resolution for WINS. Ping will resolve a name
using DNS. MS uses WINS (NetBIOS naming) for Domain Logins and for mapping
drives, etc.
Try this link on Cisco's website for help with coordinating your NT domain
with your network layout:
http://www.cisco.com/warp/publi
On Thu, 7 Dec 2000, suaveguru wrote:
> Hi,
>
> I have already configured BGP for but our trafiic for
> IP
> Address 202.95.159.0/24 not yet routing back via this
> circuit. Here is the
> configuration at our router. Can you tell us, what's
> wrong about our
> configuration.
check it with "sh i
Sure I know a reason; HP.
Really, can you give a reason why you would take HP over Cisco other than price.
Grant you 20% is a great deal of money. But do you get IOS?
Just a few thoughts.
Have a good one.
Chuck Collins
CCNP
---
We
Which firewall are you using? I've blocked my users from napster using the
PIX outbound command.
""Dave Malik"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Does anyone know what TCP or UDP ports need to be blocked on a
firewall to prevent users on a netwo
Well, well, well.
With no studying for this exam the outcome was inevitable. I am not to
bothered as Wednesdays pass eludes all.
Anyway for those people looking to sit this written exam here is the break
down.
Passing Score 60% --- sounds easy doesn't it!
Access Technologies
Access protocols
Hi,
Does anyone know of a way of finding the right answers to the Colt Exams?-
Besides digging up the answers in the book :-)
I am preparing for the CIT exam and the questions in the Colt Exam for this is
really tough in the way that they are constructed. I found most of the answers in the
C
HTML is ugly... I've found blocking the following ports does not prevent
them from downloading, but after they disconnect they never will be able to
connect again to do a search. 8875, , .
Joey
-Original Message-
From: Dave Malik [mailto:[EMAIL PROTECTED]]
Sent: Thursday, Decemb
Ash:
As I indicated in my previous post, the message "%SYS-4-CONFIG_NEWER:
Configurations from version 12.0 may not be correctly understood." is
nothing to worry about, unless you intend to run your router off the
mini-IOS version (system bootstrap) loaded on your router--which is NOT
recommended
Hi Andy,
Maybe I'm daft, but I can't seem to find out where this chat is gonna take
place? I know it isn't in *my* chat room, 'cause I haven't been in touch
with anybody for a while as I prepare for my lab exam...
Any hints?
Z
>From: Andy Barkl <[EMAIL PROTECTED]>
>Reply-To: Andy Barkl <[EMA
I just wanted to add a comment about the "translating" statement. I've
seen this many times working with my lab equipment.
When a router is behind another router acting as a terminal server you will
sometimes get this message when reverse telnetted into the router. It's
normal and caused by th
I am taking CID 3.0 640-25 on Monday. Any constructive advice?
Craig E. Smith
Network Engineer
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
The routers in question were 7206s located in Paris. I saw more of this
exact behavior on some other routers in Europe, but can't remember which
ones. Here is the relevant portion of the config for the router in question.
I don't have a good explanation for this behavior, but when I asked, I was
t
Yes, WINS resolves NetBIOS names to IP addresses, but only for Windows
networking functions. It is not used for ping, ftp, telnet, etc. It is
used for name resolution with relation to file sharing, domain traffic, etc.
The order in which a Windows box will try to resolve a DNS name (what
happen
Well, I made it under the wire...
I passed the MCNS exam this morning with an 848. I know... not the best
score to have, but it's good for me since I have always been terrible at
test taking.
I now have the CCNP - Security specialization. However, I still intend
to take the other exams that are
Greets all,
I am currently studying for the BCSN exam, have a question . . .
1. When a distant vector protocol sends out a "flash" update when a
route goes down, do the neighboring routers who receive the "flash"
update send out their own updates immediately or do they wait for their
default upd
There's a lot more to this than just typing what I tell you in examples.
Your VTP configuration must be setup on the switch side and the MSFC side.
And yes MLS is enabled at the global level but not at the interface level.
Would you like the URL's to VTP Configuration too?
Patrick
-Original
I'll tell you on Tuesday after I return if I get to take it. I just called
again and they said it was available. I'm calling 1.800.204.3926 and taking
exam 640-025. It's still listed as a live test on Cisco's web page
http://www.cisco.com/warp/public/10/wwtraining/certprog/testing/exam_list.ht
m
The log on our 2924 switch says:
%LINK-4-ERROR: FastEthernet0/1 is experiencing err
Does anyone have any more specific info as to what type of error this is
indicating?
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Repo
Jim, here is a link to an MS KB article outlining the requirements for
domain traffic over a firewall. Open these ports on the firewall to pass
the domain traffic.
Here's what happens: a client comes up and broadcasts for an available DC.
This also happens over TCP/IP, even if TCP/IP is the on
Here's my $0.2...
Few questions, just to cover the obvious:
1) Is your ISP doing filtering that might prevent this route?
2) Did you ever advertise this without the distribute lists? If so, you
may
need to clear the bgp route to your 202.161.128.173 neighbor.
3) Although you have no synchroniz
I know Foundry does a few...
-Eddie
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Chuck Larrieu
Sent: Friday, December 08, 2000 12:32 PM
To: Petra Hofmann; [EMAIL PROTECTED]; [EMAIL PROTECTED]
Subject: RE: [RE: Cisco vs. HP Switches]
Anyone know who
Niraj,
I am studying for the BSCN and using the Colt Exams as well. I find there
are many errors in the scoring and in the questions themselves. I have been
looking up the answers in the book. To me the benefit is to see the range
of topics and detail Cisco is showing us. Perhaps a glimpse int
Has anybody got an AGS+ that would work as a Frame Switch (CSC/4, at least 4
serial ports) that they would be willing to sell me?
I'm doing the Ebay thing, but not had any luck so far. If somebody has one
that they successfully used as a Frame Switch, and now they want to sell it,
drop me a li
No way ! If you are talking about All-In-One CCIE Study Guide, Second Edition, you will
be even more frustrated since you expect to see less typos. I e-mailed for errata to
the
publisher and they asked me to provide found typos. It's funny because I needed errata
to find typos that I didn't notic
Absolutely. It just makes a difference what order Windows uses to resolve.
Ping, telnet, etc will try to resolve a DNS as a DNS name. If it fails at
this, it will use WINS/LMHosts. So, yes you can 'telnet netbiosname'
If you just type in 'ping bob', Windows will tack on 'yourdomain.com' and
tr
Me too. I used outbound on my PIX by IP addr.
-Original Message-
From: Eddie Parra [mailto:[EMAIL PROTECTED]]
Sent: Friday, December 08, 2000 10:52 AM
To: Patrick Bass; [EMAIL PROTECTED]
Subject: RE: Napster block
How did you do that? Napster isn't port based... Napster can use ANY
TC
Nope...they are indeed different. At least the part numbers are different.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: Friday, December 08, 2000 12:02 PM
To: [EMAIL PROTECTED]
Subject: Flash Memory Upgrade
Does anyone know if the 2600s (not 265X) and 250
I have 1 as5300 with a voip dial-peer heading to my second as5300. on my
second as5300 I have pri's setup and I have voice ports 0:d,1:d,2:d,3:d
and
dial-peer voice 1 pots
destinatino-pattern 555
no-digit strip
direct-inward-dialing
port 0:d
(problem)when I make a call from #1 as5300 to #2 a
> The way you have written makes it sound as if I did not have DNS and I
> did a ping, telnet, or ftp by name that it would not work, and that is
> not the case.
That is not what I intended. If you do a ping, it is not a test of whether
WINS is working because there are other ways to resolve a n
Yeah...supposedly is the word. I've tried Sept 2000 will
the same problem. Verity is one of the slowest companies
in the world when it comes to staying current - what a shame.
It's not like there are any Win 2K boxes out there ;)
Roman
-Original Message-
From: Abruzzese, John [mailto:[
Hi!
Yes it's possible.
D channel is out-of-band signalling and has both signalling for B1 and B2
channels in same time.
--
WBW, xander
CCNP+Voice, CCIE Lab 19-20/04/2001
"Jun Pati" <[EMAIL PROTECTED]> ÓÏÏÂÝÉÌ × ÎÏ×ÏÓÔÑÈ
ÓÌÅÄÕÀÝÅÅ:90m7hc$m14$[EMAIL PROTECTED]
> Hi, I'm a newbie on this list
WINS is not used for ping, ftp or telnet, but then neither is DNS.
WINS is used to resolve netbios names to IP addresses. DNS is used to
resolve host names to IP addresses. If you are implying that when you do
a Telnet, Ping or FTP by name that it will not use WINS to resolve the
name to an IP a
Are you doing NAT 0 between sites so that everyone get's to use the real
IP's and not the NAT'ed ones? Are all the domain controllers, WINS boxes
etc. in the access-list defining what get's encrypted? If you are
setting up a VPN based on IP's only then you do not need to define what
ports get open
Websense is another such product.
> -Original Message-
> From: Chuck Larrieu [mailto:[EMAIL PROTECTED]]
> Sent: Friday, December 08, 2000 9:29 AM
> To: Eddie Parra; Patrick Bass; [EMAIL PROTECTED]
> Subject: RE: Napster block
>
>
> As part of some research I have been doing to address s
A better way to see if WINS (or lmhosts) is working is to use the nbtstat
command.
use: nbtstat -a <>
will try to resolve the name and give info
use: nbtstat -A <>
will give the info if the statioin is reachable.
Kevin Wigle
* * * * * * * *
Absolutely. It just makes a difference what orde
Here is the VTP configuration URL
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sw_5_4/config/vt
p.htm#32923
Good luck
Here is a good MLS Troubleshooting URL too which may be helpful
http://www.cisco.com/warp/public/473/13.html
Patrick
-Original Message-
From: Ben Ho
turn off hardware flow control (set it to no)
""Luke Everett"" <[EMAIL PROTECTED]> wrote in message
002101c0614a$4cb55400$[EMAIL PROTECTED]">news:002101c0614a$4cb55400$[EMAIL PROTECTED]...
> I have 3 different Cisco 2500 routers. When I boot them through =
> Hyperterminal I get what is below
I have 3 different Cisco 2500 routers. When I boot them through =
Hyperterminal I get what is below. It does not allow me to hit enter, =
nothing happens. I have it configured as 9600 Baud, 8 Data Bits, parity =
- none, 1 stop bit, flow control - hardware. It is the same for all =
three of
I have a Cisco 7206 with an IMA card and two ATM T-1 circuits going into the
4 port IMA card. About every two weeks the router freezes up. Usually a
reboot brings it back. Everytime the router reboots, the log gets cleared.
Is there a way I can troubleshoot the hardware and/or IOS with this and
this may not be strictly a cisco related but it is a
networking related question.
a 3Com cable modem that i have has a USB
connection (jack) that one can use to connect
to one's computer's USB jack.
does it mean that USB connections would be
similar to the RJ45 connections that we have for
conn
Hello All,
Passed BCSN this morning with an 804. Not great, but not as hard as I
anticipated. Some questions very vague!
Just as others have said, the objectives from Cisco is what you need to know
well, especially OSPF and BGP!
Sources used:
TCP\IP Routing - Jeff Doyle
Boson test 1
Various lin
Just an FYI for the group. I got the Switching Black Book from Sean Odom
and Doug Hammond. I cannot believe what it has! I know Sean Odom is known
for putting out books that are well written and takes the time to place more
than the needed technical information. What I thought I was getting wa
As part of some research I have been doing to address some issues I have
with a particular customer security design, I've been spending a bit of time
at www.trusecure.com , and the related interests Information Security
Magazine and the ICSA test labs.
What I have read there leads me to believe t
Anyone know who OEM's for HP? Long ago is was Kalpana.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of
Petra Hofmann
Sent: Friday, December 08, 2000 9:05 AM
To: [EMAIL PROTECTED]; [EMAIL PROTECTED]
Subject:Re: [RE: Cisco vs. HP Switches]
I work for a small company with 5 branches. I have a frame connection to
all the sites which connects to the central office where I am (hub and
spoke). In the central office, I have set up a PIX firewall. Behind the
firewall sits an exchange server and a new server which I plan on installing
n
Hello All,
I have 12 16/4 IBM token ring cards that have been taking up space in my
office for a while. I am offering them up to anyone who wants to pay the
shipping for them. I figure they would be good for some token ring
simulations.
Matthew
-=-=-=-=-=-=-=-=-=-
Matthew Herman
Vice P
How about getting a test machine and running nbtstats to test the WINS
resolution?
>>>Brian
>From: "Benjamin Walling" <[EMAIL PROTECTED]>
>Reply-To: "Benjamin Walling" <[EMAIL PROTECTED]>
>To: [EMAIL PROTECTED]
>Subject: Re: Still doesn't work: tough VPN question
>Date: Fri, 8 Dec 2000 08:27:
Here's some good information too (watch for wordwrap):
http://cramsession.brainbuzz.com/cramsession/microsoft/tcpip/guide.asp
Hth,
Ole
Ole Drews Jensen
Systems Network Manager
CCNA, MCSE, MCP+I
RWR Enterprises, Inc.
[EMAIL PROTECTED]
http://www.oledre
The 4 is the logging level. Port config on both sides should be looked at
for the cause. (Auto,speed,etc)
Port security? Look at the MAC's. Hope that helps.
""Kim Fisk"" <[EMAIL PROTECTED]> wrote in message
90rgj7$6hk$[EMAIL PROTECTED]">news:90rgj7$6hk$[EMAIL PROTECTED]...
> The log on our 2924 s
Excuse me... I like being the pointy haired boss... Money and hours are
better, I'm asked to do less, and I don't have to report to a pointy haired
boss...
-Original Message-
From: Bradley J. Wilson [mailto:[EMAIL PROTECTED]]
Sent: Thursday, December 07, 2000 1:42 PM
To: cisco
Subject:
Hi All,
I have one Catalys 1900 with Firmware 1.09, but I forgot the password. The
Cisco Documetation said that I need Password Recovery Utility software to
recovery Password. I logon to CCO and follow the link in document, but I can
not download Password Recovery Utility.
Where Can I download Pas
If anybody in Los Angeles buys it, I'll bring the wine, blonde and sports
car.
-Original Message-
From: Jeff Duchin [mailto:[EMAIL PROTECTED]]
Sent: Friday, December 08, 2000 5:26 AM
To: [EMAIL PROTECTED]
Subject: Re: Incredible Lab !
If anybody in the Baltimore/D.C. area buys this,
I beg to disagree with you. I can certainly telnet, ftp and ping to any
NETBios name on my network.
-Original Message-
From: Benjamin Walling [mailto:[EMAIL PROTECTED]]
Sent: Friday, December 08, 2000 9:21 AM
To: [EMAIL PROTECTED]
Subject: Re: Still doesn't work: tough VPN question
Y
This URL explains it all
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sw_5_4/msfc/mls.
htm#xtocid244531
Patrick
-Original Message-
From: Ben Hockenhull [mailto:[EMAIL PROTECTED]]
Sent: Monday, December 04, 2000 11:22 PM
To: Greene, Patrick
Cc: [EMAIL PROTECTED]
Subje
Luke,
Make sure you select the following settings in HyperTerminal:
Bits Per Second:9600
Date Bits: 8
Parity: None
Stop Bits: 2
Flow Control: None
Ash
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Luke Ever
According to this afternoon's Bates Report, there are over 95,000 routes
being advertised across the internet, at least from the vantage point of the
gentleman doing the reporting.
I bring this up because a week ago, the reporter saw 93,000 routes.
Historically, in September 1996 there were abou
In case the previous two postings won't correct your problem, try the cable.
I had a very similar problem. I couldn't get in for nothing. I saw
everything scroll but couldn't do anything. Although, I was able to
Ctrl-break during boot process to get to the prompt. Then nothing again. In
my case it
I will also be taking the BSCN on December 20th.
As for if there are "fill in the blank" or "choose from the list" type
questions in the BSCN exam. They give your a list of 50-60 questions to
choose from (most of the choices are bogus) and you can quite easily
eliminate it down to 1-2 choices if
are you sure that you are right here ?
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Some thoughts:
Send you log files to a server.
Check you IOS version against known bugs.
> -Original Message-
> From: Joseph Ezerski [mailto:[EMAIL PROTECTED]]
> Sent: Friday, December 08, 2000 5:00 PM
> To: '[EMAIL PROTECTED]'
> Subject: Need help with a failing 7206
>
>
> I have a Cis
Does Cisco make an Ethernet Switch that supports -48V power. I need =
something smaller that a Cat5K. Like a 2900XL or something.
I will even consider a non-Cisco switch.=20
Patrick
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cis
Man, I am in RTP can I come by and touch it ?
- Original Message -
From: "Dennis Laganiere" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Friday, December 08, 2000 8:44 PM
Subject: RE: Incredible Lab !
> If anybody in Los Angeles buys it, I'll bring the wine, blonde and
> According to this afternoon's Bates Report, there are over 95,000 routes
> being advertised across the internet, at least from the vantage point of the
> gentleman doing the reporting.
>
> I bring this up because a week ago, the reporter saw 93,000 routes.
At some point this week they were a
The questions you have quoted came from the Cisco Colt exams...
I have found from extensive checking that many of the questions are scored
wrong at the website.
Tom
--
Tom Keough MCSE CCNA
AT&T Global Network Solutions
Standard Access Management
Managed Router Service
Tier 2 Technical Support
Tam
Hi,
Has anyone taken the Foundation R/S combo test? I've been through study
materials on Routing, Switching and am currently reading up on Remote
Access. Thanks for any comments!
Best Regards,
Mike
_
FAQ, list archives, and subscription info: http://www.groupstu
This may seem ridiculous to alot of you, but I am forging ahead with my
question and I sure hope someone can offer me advice or help:
I am finishing up in the cisco academy in mid-month and naturally, we use
cisco press materials. I have been taking these classes for 4 semesters. I
am taking
On Fri, 8 Dec 2000, Joseph Ezerski wrote:
> I have a Cisco 7206 with an IMA card and two ATM T-1 circuits going into the
> 4 port IMA card. About every two weeks the router freezes up. Usually a
> reboot brings it back. Everytime the router reboots, the log gets cleared.
> Is there a way I can
Hi Chuck,
Thanks for the update.
Regards
Ash
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Chuck Larrieu
Sent: Friday, December 08, 2000 7:20 AM
To: CCIE_Lab Groupstudy List; Cisco Mail List
Subject: Lab Preparation Advice Revised
Hey, everyone, I'v
That's just your bootstrap version possibly not able to understand your 12.1 config
Nothing to worry about.
You can always upgrade your boot flash chips but it's not worth it.
Darren
Ash Aslam wrote:
> Hi there,
>
> I have tried the recommendations made and it still doesn't work. As
> mentio
Thanks to all respondents to this email. My 2509 Router is now working back
to normal.
> %SYS-4-CONFIG_NEWER: Configurations from version 12.0 may not be correctly
under stood.
Solution: Upgrade to newer version of bootrom.
>Router freezes at "Translating "RouterC_TermServ".
Rodgers Moore's sol
Setup a BDC/Wins Server at the Branch office.
Configure your clients so that the local BDC/WINS server will provide
logon/wins services.
Then allow the domain syn traffic from Branch Office BDC/WINS server
throught the PIX to the Central Office PDC/WINS server.
Microsoft's PDC's and BDC's
Dear All,
One of my friends in egroups suggest me to contact TAC to solve our Cisco
1005 Series which have problem but i also need oone of you in Cisco Group
Study to help me. I dont know exactly what is the problem, is it hardware or
software problem or maybe..bugs of cisco. Here, i send copy of
hi
Tanx
How to achieve this CCSE and CCSI certifications?
regards
ravi kumar B.
Brian Dellong <[EMAIL PROTECTED]> wrote:
oh boy, where did you hear these terms. overheard
in office ?
well here you go...
CCSE Checkpoint certified systems engineer
CCNA Cisco certified network associate
CCSI cisc
Hello
This may seem ridiculous to alot of you, but I am forging ahead with my
question and I sure hope someone can offer me advice or help:
I am finishing up in the cisco academy in mid-month and naturally, we use
cisco press materials. I have been taking these classes for 4 semesters. I
am ta
Hi,Chuck
Thanks a lot!!!
On 8 Dec 2000 03:26:54 -0500, [EMAIL PROTECTED] ("Chuck Larrieu")
wrote:
>Hey, everyone, I've cleaned up my CCIE Lab preparation advice file, adding
>some thoughts from some folks who recently passed ( with their permission,
>of course. )
>
>Check it out on my
Hi Andy,
Maybe I'm daft, but I can't seem to find out where this chat is gonna take
place? I know it isn't in *my* chat room, 'cause I haven't been in touch
with anybody for a while as I prepare for my lab exam...
Any hints?
Dale
[=`)
>From: Andy Barkl <[EMAIL PROTECTED]>
>Reply-To: Andy Ba
Does anyone know if the 2600s (not 265X) and 2500s use the same types of
Flash SIMMs?
Thanks
Tim
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Supposedly CDs after August 2000 work fine on Win2k.
-Original Message-
From: Hook Soso [mailto:[EMAIL PROTECTED]]
Sent: Friday, December 08, 2000 1:34 AM
To: [EMAIL PROTECTED]
Subject: problem of documentation cd
I try to install Cisco Documentation CD on Windows2000, but there is
alwa
Good point, Chuck! It gets harder and harder to stay ahead of the wolves. I
get to thinking every once in awhile in my darker IT moods that defending
against the "Net Evil" out there (real and perceived) will eventually render
the Internet unusable.
Interestingly, the SANS folks (www.sans.or
Yes. True.
In Joe's case, WINS is resolving the name to IP address.
One can also ping devices using the fully qualified domain name. In that
case, DNS resolves the name to the IP address.
I don't se anything in Ben's post to disagree with. He is speaking only of
the order in which a Windoze PC
100 matches
Mail list logo
