I've contacted the cisco TAC.
The CE write " is this router connected to the switch on the ethernet side.
If
it is then can you verify if the switch has good entries for the mac addreses
of the PC's. Also you can run "debug arp" on the router and you will see that
the router is sending arp request
The cpu load is normal (10%) for all the time.
There is a possibility that is an attack, but if I control nat translation,
cpu, int stat , I find no trace for background traffic.
Teresa
- Original Message -
From: Reinhold Fischer
To: Teresa Presutto
Cc: [EMAIL PROTECTED]
Sent:
Hi Group
What is the command to enable/disable optimum
switching on an interface?
What is the command to enable/disable silicon
switching on an interface?
Thanks
Lw
__
Do You Yahoo!?
Make international calls for as low as $.04/minute with Yahoo
You should change the order of your commands
Line vty 0 4
access-class 55 in
access-list 55 permit 202.157.78.0 0.0.0.128
For sure it will run correctly
gook luck
MNM
--- kaushalenders wrote:
> hi ,
> hi i have made a access list to restrict telnet on
> my router from other
> network but when
Hi,
You may want to take a look at this..
http://www.maximized.com/freeware/tcpspeed/
At 07:38 AM 8/22/01 -0400, Milan Saxena wrote:
>Sanjeev,
>Thanks I was having a similar problema nd was wondering where to look in
>for. If you get any clues, do let me know.
>
>Thanks.
Message Posted at
thanks tony
With regard to this question , my load balancing
solution is of this type with incoming traffic
dual-homed with the same provider with one edge router
what solution will you use for this ?
regards,
suaveguru
--- Tony Medeiros wrote:
> Many ways: And it all depends on your
Hey, experts any comments ? I thought i will get some info
on code red here . but looks like nothing !
shella
>From: "shella kevin" >Reply-To: "shella kevin" >To: [EMAIL PROTECTED]
>Subject: Code Red ! [7:16950] >Date: Thu, 23 Aug 2001 04:55:48 -0400 >
>I am using cisco7200 seri
I'm having a strange problem with a 2600 running 12.2(1a), after a short
period of time (30 to 60 mins) the router will stop logging messages to the
vty lines with terminal monitor. I can perform a show logging history and
see the last message in the history but nothing is display as it happens,
s
There is a bug when logging synchronous is used on the vty or console ports.
I hit this issue also.
^-^-^-^-^-^-^-^-^-^-^
Bill Carter
CCIE 5022
^-^-^-^-^-^-^-^-^-^-^
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Patrick Donlon
Sent: Friday, August 24
Thanks for sharing questions from the CCIE written... let us know if you
have any more...
""Wright, Jeremy"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Can you have collisions on a serial link? Thanks again.
Message Posted at:
http://www.groupstudy.com/form/read.php?f
Hi,
Just like everyone else sometimes I do not have enough time to do the
research myself and I post questions here. Here is what I am trying to
do: I am trying to set up some sort of security server on my network to
authorize user access on routers and switches. First of all what should
I us
Thanks Bill, I'll check this out straight away, was the bug introduced in
12.2? or earlier
cheers Pat
""Bill Carter"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> There is a bug when logging synchronous is used on the vty or console
ports.
>
> I hit this issue also.
>
> ^-^-
>Brian, I just wanted to say publicly that this was an outstanding test
>question. outstanding because of all the red herrings it contained, as we
>saw from the wild guess responses.
Sir, after several trips to Scandinavia, I find it hard to believe
that any sensible tester would use more than o
Remember that masks on standard access-lists are
wildcard reverse masks. try using a mask of 255 like
this
access-list 55 permit 202.157.78.0 0.0.0.255
line vty 0 4
access-class 55 in
I don't think the problem is the order of commands.
--- Midnight Man wrote:
> You should change the order of
Howard, you should try the Herrings in Curry Sauce the next time you're in
Scandinavia (Denmark especially).
Another good fish-out-of-a-can thing you should try, is the Macrel in tomato
sause on an open faced sandwich with mayo on top - YUMMI!!!
P.S. Don't forget that fish has to swim, so you'll
is there a hyperterminal version for linux?
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17115&t=17115
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosur
Learn to use the search engine on cisco.com. It's a very valuable tool.
Searching for
+"code red" +block
yielded many results, including this one:
http://www.cisco.com/warp/public/707/cisco-code-red-worm-pub.shtml
Additional Workarounds for Handling "CodeRed" Traffic
Utilize the NBAR feature in
minicom
""george gittins"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> is there a hyperterminal version for linux?
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17118&t=17115
--
FAQ, list archives, and s
After someone gives you an answer, are you going to have time to research if
it is a good solution for you or are you going to just implement it.
It sure must warm the cockles of your supervisors heart if he could see you
now.
actually the only two things that would make me to busy that I couldn't
www.google.comm and search for seyon. It is the best hyperterminal bar
NONE. And it is FREE too
>From: "george gittins" >Reply-To: "george gittins" >To:
[EMAIL PROTECTED] >Subject: hyperterminal for linux [7:17115] >Date:
Fri, 24 Aug 2001 10:01:06 -0400 > >is there a hyperterminal version for
mi
minicom
It's probably already on your system. start it up and gointo settings and
take out all the dial and hangup commands.
-Patrick
>>> "george gittins" 08/24/01 10:01AM >>>
is there a hyperterminal version for linux?
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=171
the only problem is that he doesn't have the code to support it.
>>> "Allen May" 08/24/01 10:13AM >>>
Learn to use the search engine on cisco.com. It's a very valuable tool.
Searching for
+"code red" +block
yielded many results, including this one:
http://www.cisco.com/warp/public/707/cisco-cod
Oh yeahdidn't notice the mentioned version #. I'm still looking
but not having any luck yet. It may be time to upgrade IOS
- Original Message -
From: "Patrick Ramsey"
To: ;
Sent: Friday, August 24, 2001 9:28 AM
Subject: Re: Code Red ! [7:16950]
> the only problem is
Ah, that's good to know! I've been noticing that problem on a 3660
running 12.2 and it was driving me crazy. Last time I looked at CCO I
didn't see the bug report but either I missed it or it wasn't on there
yet.
Thanks for clearing that up for me.
John
>>> "Bill Carter" 8/24/01 7:04:07 AM >
As far as I know this is Cisco newsgroup and it should be used for technical
discussions
not for personal insults. If you think that you are smarter than me or have
better work
habits that is fine, I am not going to argue with that. Otherwise I would
be asking
questions.
Donald B Johnson jr wr
if you are trying to access the router through the console port. You can use
the linux console.
Rico
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: Friday, August 24, 2001 10:01 AM
To: [EMAIL PROTECTED]
Subject: hyperterminal for linux [7:17115]
is there a
Hi All
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17130&t=17130
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Hi All
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17132&t=17132
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Hi All
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17128&t=17128
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Hi All
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17129&t=17129
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Hi All
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17131&t=17131
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
the linux console?
Is that an app or a physical device?
>>> "Rico Ortiz" 08/24/01 11:04AM >>>
if you are trying to access the router through the console port. You can use
the linux console.
Rico
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: Friday, Au
Hi All,
I am designing a network with following requirements. Can somebody suggest
me a good book on network design?
The requirements are:
1. 2 T1's to 2 different ISP for redundancy
2. Firewall
3. Host own DNS, Webserver
4. Have private network separated from the public network.
Please sugges
If you are familiar with Unix, contact me off-line and I will assist you
with installing and configuring TACACS on Unix platform. I can also help
you with configuring routers and switches as well.
>From: "khramov" >Reply-To: "khramov" >To: [EMAIL PROTECTED] >Subject:
Re: Tacacs [7:17110] >Date:
That's a very simple network... Basic design could be found on the internet
without purchasing a book.
I personally feel for a person just getting into networking, that the
"basic" books are a waste... IF you have the abillity and drive to learn
networking then you'll also feel shafted after yo
test
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17138&t=17138
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
goto http://www.priscilla.com/
She has a BOOK about Network Design called "TOP DOWN NETWORK DESIGN"
-Original Message-
From: Zolla Zimmerman [mailto:[EMAIL PROTECTED]]
Sent: Friday, August 24, 2001 10:16 AM
To: [EMAIL PROTECTED]
Subject: Network Design Book [7:17134]
Hi All,
I am desig
Hello,
i don`t mean to be rude but i think the reason the gentleman replyed the
way he did was because way you posed your question was to say
" i`m to busy ...you lot do it for me"
now i personal believe that that is not the case and you were simply asking
(as i do all the time) for some
Ok 2 jokes and then something that was posted on the groupstudy jobs
list that you may get a kick out of.
Name withheld of course.
-
Three men are traveling in the Amazon, a German, an American,
and a Mexican, and they get captured by some Amazons. The head
of the tribe says to the
Teresa,
Well, that's more information than was previously disclosed:-)
That sheds a totally different light on the matter.
Maybe it might be possible to retrace the steps for all of
this. First, was everything working okay at some time in the
past? At what point did something change or go
Sorry about this. Trying to get the mailing list working at work.
grrr
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17143&t=17143
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report
No, Paul did not implement new subject header prepends, I did that to
show where this teaser might be relevant. Okay, here goes. Not too
difficult, but the idea is to learn. If you already have this stuff
down cold, then please don't answer. ;-) That takes all of the fun out
of it.
Teaser #1
At 10:44 AM 8/24/01 -0400, Patrick Ramsey wrote:
>minicom
>
>It's probably already on your system. start it up and gointo settings and
>take out all the dial and hangup commands.
>
>-Patrick
>
> >>> "george gittins" 08/24/01 10:01AM >>>
>is there a hyperterminal version for linux?
For those wh
Hi Paul,
the following is the cisco tac case story. I closed the case just few minutes
ago.
Let me know what do you think about this.
Teresa
Hi,
I will be assisting you in the case that you have opened with us at Cisco
TAC. Can you please send the output of "sh arp" that you are seeing along
w
subject says it all. trying to figure this one out. I have seen the
enterprise software loaded on the "A" model, yet people selling the switches
differentiate between "A" and "EN" models. please clear up my confusion.
thanks
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17146
Please refer to the Swahili Binary Conversion book to answer this...:-)
-Original Message-
From: John Neiberger
[mailto:[EMAIL PROTECTED]]
Sent: Friday, August 24, 2001 11:08 AM
To: [EMAIL PROTECTED]
S
Two quick questions.
Q1. BOSON CIT
Are BOSON tests good for CIT exam? I plan to buy 2
BOSON tests. Which ones do you recommend? Should I
buy test #1 and #2 or test #2 and #3?
Q2. Cisco Training Manuals -- Copyright
I attended all Cisco training classes and have the
official training manuals
Dang it, I lent mine to a friend studying for the written exam! I don't
even think he'll need it until he starts studying for the lab. I hope
he gives it back, those are expensive and hard to find.
>>> "Wright, Jeremy" 8/24/01 10:00:32 AM >>>
Please refer to the Swahili Binary Conversion book
Oh goodness He/She sounds all of 17.
-Patrick
>>> "Natasha" 08/24/01 12:01PM >>>
Ok 2 jokes and then something that was posted on the groupstudy jobs
list that you may get a kick out of.
Name withheld of course.
-
Three men are traveling in the Amazon, a German, an American,
login and password need to be enabled in the vty configuration
add
vty 0 4
login
password thepassword
If no enable or secret password is set, you'll also need to do that to be
able to get to priveleged EXEC mode on the router - use
enable password password
-e-
- Original Message -
From
No, Paul did not implement new subject header prepends, I did that to
show where this teaser might be relevant. Okay, here goes. Not too
difficult, but the idea is to learn. If you already have this stuff
down cold, then please don't answer. ;-) That takes all of the fun out
of it.
Teaser #1
0.0.0.128 IS a wildcard mask. It just allows half of the IP addresses you
allow using the mask you provided.
The order of commands isn't important.
Kaushalenders, perhaps you could indicate which address range you are trying
to permit to have access, and which you are trying to deny access? Th
Yeah, I'm going this weekend to do my Masters in Physics. Nothing better
on a Saturday to do then ramp up my carrier!
-Original Message-
From: Natasha [mailto:[EMAIL PROTECTED]]
Sent: Friday, August 24, 2001 11:02 AM
To: [EMAIL PROTECTED]
Subject: OT: Fridays funnies [7:17141]
Ok 2 joke
I had a similar problem a year ago which turned out to be a hardware defect
in the router. It was over voltage on the line and would cause the
ethernet port to go away. Its a documented "feature".
At 11:59 AM 8/23/2001, Teresa Presutto wrote:
>It didn't ping successfully.
>In the sho log I
Try boson.com
They have good tests and only cost 29.95
PA
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Artashes Kalantarian
Sent: Wednesday, August 08, 2001 9:24 AM
To: [EMAIL PROTECTED]
Subject: CCNA exam [7:15284]
Hi All
I am new to this newsgro
The "A" model had an IOS with fewer features. "EN" upgrade was on the order
of $500. The market pushed Cisco into selling both at the same price so I
don't believe that there is an "A" anymore.
> -Original Message-
> From: chris klebl [mailto:[EMAIL PROTECTED]]
> Sent: Friday, August 24,
Yes I do agree that 0.0.0.128 can be a wildcard mask but that would only
"wildcard" one bit. That 128 would only cover the uppermost bit. But I
agree if we know what range of ips need access then we can help this guy
out.
-Haydn
-Original Message-
From: Leigh Anne Chisholm [mailto:[EMAI
Natasha that was a seminal moment in my life. I was planning on wasting 8-12
months studying for the lab. Maybe I need to join the jobs group if the
humor is that rich. Probably a better fit for me.
Thank You,
Donald B Johnson Jr
- Original Message -
From: "Natasha"
To:
Sent: Frida
No that is not it Steve, my therapist says if I'm good all week I can have a
relapse or two on friday. P>)
- Original Message -
From: "Stephen Skinner"
To:
Sent: Friday, August 24, 2001 9:00 AM
Subject: Re: Tacacs [7:17110]
> Hello,
>
> i don`t mean to be rude but i think the r
Natasha that was a seminal moment in my life. I was planning on wasting 8-12
months studying for the lab. Maybe I need to join the jobs group if the
humor is that rich. Probably a better fit for me.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17164&t=17164
Answer 1 download the demos and see which ones you like best. I always
checked which works they referenced for their explanations. if I had that
volume in my libabry it was probably a shoe-in.
Answer 2 good question my first thinking would be no but since I also donate
stuff and work with my local
Does anyone have a router acting as a bridge in their lab network?
Cisco documentation claims that there is a "debug span" command that shows
BPDU frames in hex as they come in. Now, I think this is an awful idea,
since they come in every 2 seconds, but for a project I'm working on I need
to f
Teresa,
I read the email exchanges. Did Cisco resolve the matter for
you? Reading the exchanges below, that is not exactly clear.
If you were getting 4000+ packets per second very late at
night, I would tend to agree with another poster (was it
Rheinhold?) that there is possibly some form
Hamid,
Don't know if you've already seen this, but check out
http://www.cisco.com/warp/public/473/50.shtml#cisco2600
>From what I see on this page, it would appear that a FastEthernet port is
required for interVLAN routing.
BTW, group, I noticed in the configuration section of this page that t
RouterD#debug span
debug span
% Incomplete command.
RouterD#debug span ?
events Spanning tree topology events
treeSpanning tree protocol data units
RouterD#debug span events
Spanning Tree event debugging is on
RouterD#debug span tree ?
RouterD#debug span tree
Spanning Tree BPDU debu
Howard,
Does is it really matter if it is BSC or SDLC multidrop network. In an IBM
SDLC network you are dealing with Master/SLave design so you will never get
collisions becuase the Master controlls the transmission time
Most are full duplex, so in those cases, no you shouldn't..
>
>Brian "So
I wonder if "debug span tree" is the one that shows the packets?
Any chance you could try for me?? ;-] You would have to have bridging
enabled on a couple routers or a router connected to a switch.
I am interested in the output. I want to see the actual packet and document
the output, because
Hi, Guys: Does anyone have a good suggestion which CCIE lab trainning
camp is the best? mentortech, ccprep.com or others? Thanks, ~ml
Get your FREE download of MSN Explorer at http://explorer.msn.com
Message Posted at:
Does anyone have suggestions/preferences on what syslog server to get?
Thanks.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=17171&t=17171
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
This isn't an actual answer to your question about BSC and SDLC, which
Howard can do, but for all of you wondering about this issue, I recommend
chapter 3 of Tannenbaum, "Computer Networks."
He goes into lots of interesting details about how to allocate a single
broadcast channel among competi
syslogd
:)
Of course it runs on unix/linux... Did I mention that Suse was a good distro
to start with?
>>> "Wright, Jeremy" 08/24/01 02:10PM >>>
Does anyone have suggestions/preferences on what syslog server to get?
Thanks.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=1
Portfast does not disable spanning-tree. It is meant for connections between
an endstation PC and a switch. Upon PC startup the link immediately goes
into forwarding mode. If a loop did exist the link would transition to
blocking.
> -Original Message-
> From: Patricia Leeb-Hart [mailto:[E
You might also consider:
http://www.kiwi-enterprises.com/software_downloads.htm#Syslogd
It is now freeware.. and if your not a *nix user it runs under Win9x, ME,
XP, NT4 & 2000.
Really nice and easy to use.. Also supports SNMP traps etc etc..
Dave
>>> "Wright, Jeremy" 08/24/01 03:10PM >>
Hello, all.
I hope I'm not being redundant redundant, but I can't locate this in the
archives, so here goes:
I haven't had the occasion to do much with either the Catalyst 5000 or the
1900 series, I've only worked with 2912/24. For purposes of studying for an
eventual CCIE lab, are the 'set' an
NT or UNIX
- Original Message -
From: "Wright, Jeremy"
To:
Sent: Friday, August 24, 2001 11:10 AM
Subject: Syslog Server [7:17171]
> Does anyone have suggestions/preferences on what syslog server to get?
> Thanks.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=1
It has been a while since I have touched a 1900 but I am pretty sure that
the 1900 uses IOS so you would not be able to learn the Catalyst set/clear
command structure on this switch.
Heather
> -Original Message-
> From: Don Claybrook [SMTP:[EMAIL PROTECTED]]
> Sent: Friday, August 24, 20
Actually, I have been considering taking a couple of months off since the
market is kind of slow right now and get my M.D. Never hurts to have a
backup plan if the current career path doesn't pan out. ;-)
Heather Buri
> -Original Message-
> From: Steve Smith [SMTP:[EMAIL PROTECTED]]
>
Heather, the job market isn't slow... it's that there's people like that
which Natasha posted about out there that we're competing with. If an
employer had to choose between someone who could pass the lab in 20 days, or
someone like you or I that would take months, if not years to do, who would
y
Thanks for clearing this up! This comes as a tremendous a relief to me and
inquiring minds on my other mailing lists
>>> Daniel Cotts 08/24/01 11:15AM >>>
Portfast does not disable spanning-tree. It is meant for connections between
an endstation PC and a switch. Upon PC startup the link immedia
No. The 1900 is a unique cat in that while it is similar (more like router
IOS)to the 2900 it is not the same. It is not at all like the Cat5K line
which uses set and clear commands. An old 2901 might be your least expensive
way to learn that command set. It is limited to about ver 4.9 of CatOS.
S
Leigh Ann, that is a good point. I could never pass the CCIE in 20 days.
Heck, I am still waiting for the "CCIE for Dummies" to get published. :-)
I needed a good laugh today and that job posting sure did it for me!
Thanks,
Heather
> -Original Message-
> From: Leigh Anne Chisholm [SM
I just looked in "Cisco LAN Switching" from Cisco Press by Clark and
Hamilton. A great reference book.
> -Original Message-
> From: Patricia Leeb-Hart [mailto:[EMAIL PROTECTED]]
> Sent: Friday, August 24, 2001 2:07 PM
> To: [EMAIL PROTECTED]; [EMAIL PROTECTED]
> Subject: RE: Problem Using
I am currently preparing for my last CCNP exam (CIT), and are therefore
slowly considering what to do next.
My experience with Cisco routers, switches, etc. is still too low for me to
even consider going for the CCIE right away. However, security is one of the
areas where I lack knowledge and exp
Thanks! Looks like I'll be visiting Stacey's bookstore again during lunch
I've bought so many tech books there I've earned a $100 freebie.
>>> Daniel Cotts 08/24/01 12:12PM >>>
I just looked in "Cisco LAN Switching" from Cisco Press by Clark and
Hamilton. A great reference book.
> -Origi
The networking giant will replace a structure aligned according to customer
market. Cisco also said its business is stabilizing.
http://computerworld.com/nlt/1%2C3590%2CNAV47_STO63262_NLTAM%2C00.html
http://newsroom.cisco.com/dlls/corp_082301b.html
Message Posted at:
http://www.groupstudy.co
Don,
The 1900 CLI is not the same as the 5000, but if you'd like, feel free to
download my free homemade Cat5000 set-based command trainer by following the
RouterChief link below.
Have a great weekend,
Ole
~~~
Ole Drews Jensen
Systems Network Manager
CCNA, MC
The inverse mask on this is likely incorrect, if yoy want it to be for
half a class c, you want 0.0.0.127
Brian "Sonic" Whalen
Success = Preparation + Opportunity
On Fri, 24 Aug 2001, Midnight Man wrote:
> You should change the order of your commands
> Line vty 0 4
> access-class 55 in
> ac
Hi Ole,
I am in the same boat as you. I am getting ready to take my final exam
(CIT) yet feel that I have nowhere near the experience level to think about
attempting the CCIE lab. I need at least 2 more years of good, solid
hands-on experience before I am ready to attempt that.
I am also con
OK that does it Heather! Next weekend I will test out and get my PhD. in
Quantum physics.
StevePhD / MD soon to be!
-Original Message-
From: Buri, Heather L. [mailto:[EMAIL PROTECTED]]
Sent: Friday, August 24, 2001 1:51 PM
To: Steve Smith; [EMAIL PROTECTED]
Subject: RE: Fridays funn
Ah the old "OSPF over frame relay" problem!
You, sir, have discovered one of the CCIE core topics - something you MUST
know inside out to pass your Lab.
This isn't a "strange problem". This is a well known behaviors that gets to
the heart of OSPF and NMBA.
The fact that you are asking the q
Thanks everyone, I have fixed the rommon booting problem and the RSM now
boots the image. The main issue was my understanding (or lack thereof) of
the config-register. For some reason, I thought the value displayed in "show
versions" was the value you were -supposed- to set the config-register
to.
Comments within and below.
> Does anyone have a router acting as a bridge in their lab
network?
Yes, a bunch of 2500s running everything from 12.09 to 12.2(3)
and experimental smokin IPv6 code. I also have a BFR (Cisco
7000) running 11.2(16)
> Cisco documentation claims that there is a "deb
Well, my advise to all is still the same, don't buy from
1. OneSource
2. IQSale
3. GrandStore
4. Hitek
They are the same companies and they seems to believe that changing their
names help to avoid their responsibilities to their customers. They are
FRAUD and CHEATER . I will also put up the name
Do you have any of the commands similar to the ones below?
ip local policy route-map 10 (needed for traffic created by the router)
interface Serial0
ip address 10.10.1.2 255.255.0.0
encapsulation frame-relay
ip ospf hello-interval 20
ip policy route-map 10 (needed to apply the policy routin
command
debug ip packet detail
Best Regards
Have A Good Day!!
***
Farhan Ahmed*
MCSE+I, MCP Win2k, CCDA, CCNA, CSE
Network Engineer
Mideast Data Systems Abudhabi Uae.
***
Privileged/Confidential Informati
Phil,
You didn't mention how much memory that you have. Some of the ones that I
wanted to run required 32mb and I only had 16, so I am still running 12.0(2)
or 12.0(6). Can't really recommend them though, as I am having problems
running BGP on them. One of them keeps rebooting immediately after e
96 matches
Mail list logo
