Hi folks,
I have one workstation and a server, one one each vlan, running ISL on a
cat5500+RSM between the two vlans. When I ftp from the workstation to the
server, I get really slow speed, about a couple kbits/s and eventually, it
times out with a meesage: NETOUT:connection reset by peer.
Here
Hi guys,
I'm running a pix 520 with a non-stateful failover. The image is
4.4(6). I've been receiving a lot of ftp disconnect/failures from the
ftp-server that are sitting in the dmz, behind the pix520. Has anyone
experienced ftp problems on pix520 running 4.4(6)? Should I consider
upgrading t
Hey guys,
I got eth0= security0 and eth1=security100. I'm able to telnet from the
inside network. Is there any way for me to telnet from the outside? Pix
has disabled this by default.
-Frank
_
FAQ, list archives, and subscription info: http://www.groupstudy.co
Hi guys,
Can someone please explain to me about this Licensed connections on a Pix
520:
pix-520P# sh ver
PIX Version 4.4(6)
Compiled on Sun 24-Sep-00 19:22 by pixbuild
Finesse Bios V3.3
pix-520P up 130 days 22 hours
Hardware: AL440LX, 32 MB RAM, CPU Pentium II 266 MHz
Flash atmel @ base 0x30
Hi folks,
If you have three T1's coming from the same provider which go straight
into one single router and between you and the provider, you guys are
doing multigroup ppp with ip cef load balancing 'per packet'. Ultimately,
do you have the same kind of inbound/outbound bandwidth in this scenario
Hi folks,
Anyone able to get tftpserver to run on redhat 7.0? I was able to to run
it in 6.x. And I would hate to have a tftpserver running on a windows
box because most of the work I'm doing is through remote. And no, I would
not downgrade my redhat box to 6.2. Thanks for any help.
-Frank
Hi folks,
>From this url
http://www.cisco.com/warp/public/cc/pd/iosw/iore/iomjre121/prodlit/1065_pp.htm
it states that 12.1(2)T supports dhcp client on ethernet interface. I was
not able to find the ios code for the 4000 series router anywhere on
CCO. I tried using the 12.1(7)T code on the 4000,
Please contact me offline if you can sell high volume FLASH/RAM for cisco
routers. Thanks.
-Frank
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Hi folks,
Is it possible to replace the current motorola cable modem box with a
2514? If so, how do you do it? If not, what is the reason or what is the
difference between that motorola box vs a 2514 cisco router? thanks for
any input.
By the way, I'm not asking to cross-over between the motor
Eric,
I ran in the exactly same problem as you were having. And 'no fixup smtp
25' was the fix.
-Frank
On Wed, 21 Mar 2001, Eric McMasters wrote:
> I have PIX 515 w/5.3(1) IOS running and I ran into a problem with SMTP
> connectivity between two Exchange servers. I have the FW opened up to a
Hi folks,
I have a T1 attached to my Serial0. I would like to limit traffic on my
192.168.168.1.9/29 to only 128kbps for both input/output. Can this be done on a Cisco
4000 running 12.07T ip-plus? Thanks for any input. Below is my config:
interface Ethernet0
ip address 192.168.1.1 255.255.
Since we're talking about 4000's, how can we distinguise it from a 4000,
4000m, 4500, or 4700? They all look the same. Also, unlike the 2500
series, they don't tell you the sub model from the back.
-Frank
On Tue, 12 Dec 2000, Circusnuts wrote:
> This is the story of a man who said he would
;s. If you see ATM or Fast
> Ethernet (this FE module is more expensive new/ list price, than a new 3640
> with an FE module) for sure you have a 4500 or better (32/16)...
>
> Phil
>
>
> - Original Message -
> From: "Frank Kim" <[EMAIL PROTEC
Tim,
You're probably talking about TXport product. If so, they were bought out
by verilink. Go to www.verilink.com and do a search for 'txport'. You'll
find plenty of info for your csu.
-Frank
On Thu, 28 Dec 2000, Medley, Tim wrote:
> Sorry for the off topic post.
>
> I just came up with
Hi folks,
I have a bunch of dual-ethernet(NP-2E) on my Cisco 4000 routers. I would
like to trade it for either serial modules or token-ring modules. Please
email me if interested.
-Frank
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/
Hi guys,
Has anyone experienced speed or duplex negotiation between a pix 506
ethernet interface and a cisco 2610's ethernet interface using a
cross-over cable between the two? Should I uplink those two into a switch
and let the switch worry about the negotiation? I'm currently
experiencing 'int
Has anyone implemented port filtering to disable AOL instant messenger and
Yahoo instant messenger? If you have, could you send me the ports they
use on those? Could you also tell me what techniques you used, doing it
at the firellwall(pix) or the router? Thanks for any input.
-Frank
___
s.
Cheers,
Frank Kim, MCSE, CCNA
Systems Engineer
Comegetus Te
You must be refering to ATM. The reason it's 53 bytes in a cell because
the first 5 bytes are used for cell-header information; the other 48 bytes
contain the payload, which is data.
Cheers,
Frank Kim, MCSE, CCNA
Comegetus Technologies
Phone: 858-831-0296
Fax: 858-831-0687
Email: [
hift-F6 x" and then type another
session number to get into that session.
If you still have problems, feel free to call me up during business
hours.. I can walk you through. :-)
Cheers,
Frank Kim, MCSE, CCNA
Comegetus Technologies
Phone: 858-831-0296
Fax: 858-831-0687
Email: [EMAIL PROTECTED]
h
as a rolled cable between 2511RJ and console ports.
> Thought I'd check anyway, just to confuse things.
>
> Cheers,
>
> Gareth
>
>
> "Frank Kim" <[EMAIL PROTECTED]> wrote in message
> [EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > S
Yes Mom!
On Fri, 27 Oct 2000, Charlemagne wrote:
> Everyone,
>
> Don't put down lies or exaggerate on your resumes.
> You will be uncovered. Things like, "Very Familiar
> with OSPF" leave you open to questions like "Explain
> the problems with OSPF over Frame-Relay partial mesh
> networks".
Hi Tai,
Give me a call. I can help you with that.
Cheers,
Frank Kim, MCSE, CCNA
Comegetus Technologies
Phone: 858-831-0296
Fax: 858-831-0687
Email: [EMAIL PROTECTED]
http://www.comegetus.com
Cisco Training in San Diego
On Mon, 30 Oct 2000, Tai Ngo wrote:
> Hi there,
>
> Currently
Can someone please explain to me why there is a "ip nat" feature in a
Catalyst 3524en? Perhaps it's possible to run NAT on a Catalyst 3524?
coreswitch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
coreswitch(config)#ip nat
coreswitch(config)#ip nat ?
inside Inside
Manishkumar,
clear line 1-16 will reset your connection
-Frank
On 3 Nov 2000, Manishkumar Patel wrote:
> Dear All,
> Hi!
> I have setup 2511 as Terminal Server, with the Octal RJ-45 cables connected to
> Console port of 4 2500 Routers. During a day the reverse Telnet works fine,
> but when I tr
Hi folks,
I have a Pairgain T1 campus with a DSX-1/v.35 interface. Can this be used
to attached to a T1? Thanks for any input.
-Frank
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure viol
Hi folks,
Let's say within your 192.168.1.0/24 network, u have a
HostA(192.168.1.10/24) and you want to only allow HostA to use a maximum
of 10kbps of bandwidth for each of the incoming ip connection. So if
HostB(1.1.1.1/24) wants to talk to it, HostA will only reserve 10kbps for
hostB. Can this
Hi Folks,
I would like to know when upgrading my vpn3030 from 2.5 to 3.0, will I be
able to use the old config or will I need to make a new config from scratch
on the 3.0? Also, once I'm running 3.0 on my concentrator, can
those people who use 2.5 vpn client still have access or they will be
forc
Hi folks,
Anyone has any success on installing the cisco vpn 3.0 client for win2000
professional or adv server? My win2000 box kept failing after the
installation; it kept rebooting. Please share your experience. This is
the name of the file which I tried to install: vpnclient-win-3.0.1.Rel-k9
Hi folks,
I have a sco unix box which I would like to have 4 vt100 terminals attach
to via serial. These 4 vty terminals will be used for students who will
be accessing my cisco lab. I'm running into a situation where I can only
hook up two vt100 terminals to my SCO unix box because the hardware
Hi folks,
Is it possible to combine two flash partition into one so I can put a
bigger ios image in the router? Currently it shows as:
Router>sh ver
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-D-L), Version 12.0(12), RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2000
Hi guys,
I have a Catalyst 3524 XL Enterprise that I would like to trade for a
switch that can do catOS. I can add in a 2501 router if needed. Here is
a sh verion of my switch:
I can add in some money if needed.
cat3524#sh ver
Cisco Internetwork Operating System Software
IOS (tm) C3500XL Sof
Hi folks,
I was able to make my 2511 talk dhcp on its eth0 with ios 12.1(2)T
with the command 'ip address dhcp'. Right now, I'm trying to do the same
on my 4000m. But unfortunately, version 12.1(2)T does not have an ios for
4000m series. What other ios verion I can use to make my 4000m talk dh
Hi folks,
I have a 1601 router with 4meg flash and 16meg dram and a 2501 router with
16megs of flash and 16megs of dram that I would like to trade for either a
Catalyst 2901 that runs CatOS. Please reply if interested.
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=
Hi folks,
I would like to trade my 2511(terminal server) router that comes with
16megs of flash and 16megs of dram and my Catalyst 1924 EN menu-driven
switch for a Catalyst 2900 that does CatOS or a CAT5000. I don't mind
paying a bit extra for the CAT5000. Please reply if interested.
-Frank
I'm proud of you. Go Vietnamese! I'm taking my lab this November
also. I hope I will be the second Vietnamese person who will send out
such good news to the group.
-Frank
On Thu, 10 May 2001, DUNG H. LE wrote:
> May 7-8, 2001 - RTP Lab facility
>
> This was attempt 2. I changed my study h
Hi folks,
I got a bunch of NP2E(2 ethernets) for cisco router 4000/4500/4700 series
that I would like to trade for any serial, tokenring,isdn,fddi
modules. Please reply directly to me if interested. Thanks.
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=4296&t=4296
Hi folks,
After doing a few sell offs, I end up with 4 sticks of 8meg flash. I
would like to let it go for$60/each. Please email me directly if
interested.
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=4330&t=4330
--
Hi folks,
I got a 2511 with 16megs flash and 16megs dram that I would like to trade
for a 2621 router or equivalent. Reply directly to me if interested.
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=4726&t=4726
--
FAQ
Hi folks,
I got a Catalyst 3524 with two GBIC modules and two fiber cable that I
would like to trade for a Catalyst 2901 or an equivalent switch that can
do ISL/802.1Q and CatOS. Or if you feel you got a decen/equivalent in
value router that you like to trade, please email me directly.
-Frank
There is no such thing as stupid question. People have questions so they
ask. We are here to share knowledge. Selfish people like you are a waste
of bandwidth in this groupstudy! Please be a bit more considerate next
time when you send out something.
-Frank
On Thu, 17 May 2001, What's up! w
Hi folks,
I like to setup a policy so that any traffic destined to 1.1.1.0/24 will
take precedence over the rest. My outbound link is a single T1. Please
throw me a short sample config. Thanks for helping.
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=5227&t=5227
Hi folks,
I need your help. I have a 2511 router with 16 async lines. I have a
modem attached to the first line, which is line 1. I normally allow my
users to sit on an NT box and telnet to the ip address of the ethernet
interface on the 2511 on port 2001 to get into the modem so they can dial
Customer has 2511, he has modem attached to one of the Async
line and that modem is connected to one of the Unix server, he is sitting
on an NT machine connected to ethernet interface of Router, he uses a
telnet program to get connection to modem on Async line and then dial into
Unix box. After h
Below is my config of a 2511. My question is if I sit on another
workstation and telnet to 192.168.1.1 2001 which brings me to R1. Once
I am in, is there a 'key-stroke' I can enter in to have the 2511 terminate
my session? I'm currently closing out my telnet application to have the
session term
>
> r1 is gone and you're left with the terminal server connection
>
> Kevin Wigle
>
> - Original Message -
> From: "Frank Kim"
> To:
> Sent: Wednesday, 23 May, 2001 20:38
> Subject: reverse telnet [7:5655]
>
>
> > Below is my
Okay guys. I am really sorry for the waste of bandwidth. But so far, I
think I have been misunderstood. Here is what I got:
1) 2511 with e0 = 192.168.1.1/24
2) one 2501, console's port is attached to line 1 of 2511
3) one NT box with ip of 192.168.1.2/24
I sit on my NT box and I initiate a t
You can shortcut the
> exit statement, maybe an Alias of "E."
>
> Have I misconstrued ???
> Phil
>
> - Original Message -
> From: Frank Kim
> To:
> Sent: Thursday, May 24, 2001 1:51 AM
> Subject: CLARIFICATION: 2511 with reverse-telnet [7:5686]
>
Hi folks,
I got the above modem which currently only speak xon/xoff which is
flowcontrol software. Is there any hayes expert out there that can show
me how to initialize this modem so it will speak 'flowcontrol hardware'
? I got four of these modems that I use to dial into a
phoneswitch. Thanks
session without
> exiting telnet? I understand from a terminal server point of view, where
you
> might need to switch to a different line, but I'm missing why you'd telnet
> directly to something and then want to exit the session without killing
> telnet.
>
> Andras
>
Hi folks,
I've been pounding this group with tons of questions. Nevertheless, my
quest for knowledge continues on. My question is, has anyone ever seen a
4500M being deployed for full-routes bgp on the internet? CCO claims that
a 4500M can only go up to 32megs for the main memory, that is 16meg
then your
> using the 2511 as a console/terminal session so it
> behaves differently. This is the way I understand it
> and best I can explain it.
>
> --- Frank Kim wrote:
> > Erick,
> > When you telnet into a 2511's ethernet address via
> > port 2001 which
Hi folks,
I want to get rid of my current lab. Please make me some offer directly
via email if interested. Below is what I have:
4000M NP-4T, 2xNP-2E, 8meg flash, 16meg
dram
4000M NP-2T, NP-2E, NP-1R, 8meg flash, 16meg
dram
4000M NP-2T, NP-2E, 8meg flash, 16meg
dram
4000M NP-2T, NP-2E,
Hi all,
I got a pc sitting behind a cisco4000. The cisco4000 runs nat with
192.168.1.0/24 for the inside network. I am trying to establish a vpn
connection to a cisco3030 concentrator with no success. I replaced the
cisco4000 with a linuxbox running 'iptables' and it worked fine. What am
I mis
Folks,
Nevermind the below message. I found out how to enable ipsec behind nat
on CCO. Problem fixed. Thanks.
-Frank
-- Forwarded message --
Date: Wed, 30 May 2001 07:46:59 -0400
From: Frank Kim
To: [EMAIL PROTECTED]
Subject: VPN to Cisco3030 concentrator behind nat [7:6405
Hi folks,
I am in need of a wireless solution for my home-lan for my laptop. So if
you have Cisco aironet, netgear, or linksys that are not used, I would
like to make a trade with you. I need a base-station and a pcmcia
card. Below is what I currently have in my inventory:
A few 8megs flash s
Hi folks,
I'm confused with the output of 'show proc mem'.
On a 4000m, I have:
cisco 4000 (68030) processor (revision 0xB0) with 16384K/4096K bytes of
memory.
And my output for sh proc mem is:
4000M#sh proc mem
Total: 4745316, Used: 2492048, Free: 2253268
##
Hi folks,
I just did a delete flash:c4500-is-mz.113-11b.bin on my 4500m
router. Here's the output of sh flash:
gateway#sh flash
System flash directory:
File Length Name/status
1 9028608 c4500-jk9s-mz.122-1.bin
2 4003224 c4500-is-mz.113-11b.bin [deleted]
[13031960 bytes used, 374525
Hi folks,
Is it true that the 4500m routers have the same cpu as the 7000 w/ RSP
routers? Check out the sh ver on each:
# on the 4500m
cisco 4500 (R4K) processor (revision D) with 32768K/16384K bytes of
memory.
Processor board ID 04008700
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
# on th
Hi folks,
I know ISL/802.1q can only be implemented with FE or GigE. Is there any
reason why ethernet interface isn't in the game? I know 10mbps is slow
but it's a useful feature for folks with 10mbps swithces online and don't
have routers with FE interface. I overheard somewhere that newer ios
'minicom' is good
On Mon, 4 Jun 2001, nethacker711 wrote:
> I was searching the archives and could not find this one. Does anyone know
> of or can recommend a good HyperTerminal like program that will let me
> console into Cisco routers and other devices on Linux (RedHat)?
Message Posted at:
I'm currently using ip cef on my 4000m with two T1s attached. And I'm
getting true 50/50 outbound load balancing. My router is ip cef enabled
with ip load-sharing per packet. And of course 'ip route-cache' is
disabled on the interfaces as well.
-Frank
On Wed, 6 Jun 2001, Chuck Larrieu
wrot
Hi folks,
I'm in need of a Catalyst 3920 for my studies of broken-ring. I have
the below gears for you if you wish to make a trade with me. If u'r
asking for monetary value, please let me know how much. Please send your
email directly to me. Thanks.
4000M NP-4T, 2xNP-2E, 8meg flash, 16meg
Marc,
When you said it's the 'same switch', do you mean it's a physical
match? Only difference is the logo/brand on the outside? Or do you mean
the Olicom 8600 has similar functions to the Cisco Catalyst 3920? Just
curious because I am looking for a cat3920 myself. I want to spend the
least am
Juan,
12.1(2)T ios and higher will supports dhcp client.
-Frank
On Tue, 12 Jun 2001, Juan Blanco wrote:
> Team,
> I have a cable modem connection, I want to be able to use my Cisco 1600
> router, does any ones know I could find some information of how doing this,
> the problem
> that I se
putting the router in 0x41 mode will also allow you to have r/w to flash.
eric, how did the test go? congrats?
-Frank
On Fri, 15 Jun 2001, EA Louie wrote:
> The only reason (that I can think of) that you'd need to do that is to
write
> a new image onto flash. And when you do a 'copy tftp fla
Interesting! I didnt know you can do vlan routing on just ethernet
interfaces. I thought you would need a fast-ethernet interface for
that. But oh well, it's about time for Cisco to act smart. I know
Foundry iron family products support vlan routing even at 10mbps ethernet.
-Frank
On Wed,
Hi folks,
Before I throw this on ebay, I would like to see if anyone in this group
will need this router. Please make me an offer. The router comes with:
NPE150
PA-4E (4ethernets)
PA-FE (1 fast-ethernet)
PA-2T3+ (2 td/ds3 with built in dsu)
128megs of ram (good for bgp)
16megs of flash
You may
You need CCO for this.
-Frank
On Wed, 27 Jun 2001, Eric Rivard wrote:
> does any one know where I can download the Cisco VPN client for Windows
> 2000? I found the Secure VPN client vs 1.1 but it won't work on w2k. I
> see that you can get a 3des version, but I don't want to get a 3des
> versi
From: Holger Eichhorn [mailto:[EMAIL PROTECTED]]
> Sent: Monday, July 02, 2001 2:51 PM
> To: [EMAIL PROTECTED]
> Subject: Re: Cisco VPN CLient [7:10150]
>
>
> ?o)
>
> I don't understand the answer.
> I can't find the location or a hint to find the VPN-Clie
-Frank
-- Forwarded message --
Date: Mon, 2 Jul 2001 15:23:56 -0400
From: Frank Kim
To: [EMAIL PROTECTED]
Subject: URL for Cisco vpn client 3.0 for win2k [7:10701]
You need CC
Michael,
You can do dot1q(802.1q) trunking on a 10mbps ethernet link but not
ISL. You need to use high end routers such as the 4500 or the 4700. I
got one 4500m left with 2 ethernet ports left I can give to you for a good
price if you're interested.
And if anyone flames me about claiming that 1
Hey guys,
Help me get rid of this router. Below is the info to log into
router. Please don't make any changes. It has full bgp routes to
internet. You can see it with 'sh ip route' or 'show ip bgp' or 'show ip
bgp summary'.
You may log into the router to check it out. It is currently attac
Just find any 4meg flash stick that you use for your 2500/4000 series and
plug it in there. You can then download the boot-image from CCO and tftp
it into there. Remember, this is just a helper image; it doesnt give you
full-feature ios commands/functionality. So you will still need to
download
I used to deploy massive F760 netapps. They were great for NFSing; but
they were also very heat-sensitive. You may check your
datacenter/computer room to make sure it provides enough cooling before
throwing those netapps in there. As far as pricing for netapps, they are
'expensive'. For SAN so
Steiven,
It sounds like those users who have logged in were using PAT(single ip
nat'ed). If that's the case, then your ACS/pix can only see one single
ip. Only enhance you can change on the pix is to change the time-out to
be as low as you can without annoying users logon process.
-Frank
On
Ahmed,
The 4000 can go up to 16megs of ram. With the 'm' added to it, which is
'memory enhanced', it can go up to 32megs of ram. There is also a major
difference between the 4000m vs 4500m. The cpu on the 4000m is a weak ass
motorola 40mhz cpu. While on the 4500m, you get a 100mhz RISC cpu. W
Hi folks,
Can anyone give a good explaination for the above? Mainly, what's the
difference, and in which case would you use one or the other. I'm
currently using car-filter now and it works great! But I'm just curious
if I can make traffic-shape do the same function as rate-limit. For those
th
Hi guys,
Let's say i have two 520s running failover. Assuming that licensing isnt
a key issue here. Can I just turn disable failover on the configuration
and take one pix out and use it as a normal pix? So my question is, will
I end up having two pix'es ? Thanks for any help.
-Frank
Messa
George,
You probably end up better with 256megs of ram or more. With 128megs of
ram and you're running 12.2.2T code, assuming that you're running
enterprise or higher level such as for ssh, you probably using about 1/3
of your ram just for loading the ios code. So you don't have much. I
would s
On Thu, 19 Jul 2001, Circusnuts wrote:
> sure can do 32 RAM (even the 4000M). The max IOS for that router
> "currently" is 12.1(9) & the Enterprise Plus requires 8F/16R.
>
> Phil
Actually you need to have 8F/32R to do the max ios on the 4000m.
-Frank
>
> - Original Message -
> From:
Hi guys,
Does anyone know if there is any trick to make a PA-FE-TX runs at 10mbps
ethernet? Seems like it can only take 100 full or half. Thanks for any
help.
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=13585&t=13585
-
Hi guys,
I need to find a good and cost efficient IDS solution. Please
advise. Please also give me your opinion about BMC Patrol as
well. Thanks.
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=13630&t=13630
--
FAQ, l
You can actually do a lot of interesting policy routing and load balancing
with both dynamic and static routing if you use two 2501s with two dte/dce
cable. I would load the 2501 with 12.1(2)T codes or higher so it can pick
up the ip address via dhcp from cable modem provider. Uplink the
cablemo
Yes. The words are swapped around. They are both 72pin simms.
-Frank
On Tue, 24 Jul 2001, [EMAIL PROTECTED] wrote:
> Does anybody know offhand what the difference between the MEM-NPE-128MB and
> MEM-NPE-128MB=
> is.
>
>
>
> Thanks,
>
> Duncan
>
> Duncan Wallace
> Sr. Network Engineer
Hi guys,
I dont' know why i'm posting this in here. But what the hell. I need to
get rid of the router.
http://cgi.ebay.com/aw-cgi/eBayISAPI.dll?ViewItem&item=1258503547
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=13652&t=13652
Hey guys,
I know no one in the world would put two T1s on a 2501 router. But I
maybe doing this soon. I am currently using a 7200 router for my two T1s
but I feel like taking it offline and sell it to pay for my ECP1 and my
trip to San Jose for the lab test. So I'm going take out my 2501 and se
Hi guys,
I got a cat5500 originally running on 16megs of dram and 8megs of flash on
some old ass code. I took out that 16megs dram stick and traded it off
for a carnesada burrito. Luckily, I had a 32megs dram stick left so I
plugged it into the cat5500 and it worked like a champ. After finishin
Hey guys,
I know this is off the topic. But it is network security related. I have
an smtp server running hp-ux and I'm looking for a good virus filter
software to install on it. Thanks for any advice.
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=13997&t=13997
--
Can I use pc100 dimms?
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=14585&t=14585
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL
Please reply privately. Thanks.
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=15831&t=15831
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure vi
Hi guys,
I got a I/O-FE that doesn't get inserted or recognized after booting
up. Is there anyway to manually force it to insert once the router is
booted? Below is my show diag:
slut-hosting#show diag
Slot 0:
Fast-ethernet on C7200 I/O card with MII or RJ45 Port adapter, 1
port
This is just as easy as if you need to decide to run BGP or static route.
1) Is money important to you? if so, take the job that offers you higher
salary.
2) Is learning/experience more is more fun for you? if so, take the job
that you will think will allow you to play with more gears.
3) Is sex
Hi guys,
I'm using sniffer pro 3.0 on NT platform. I am able to filter a single
host or any host. But I cannot filter a subnet, for example,
10.10.10.0/24. I have tried entering in all sort of combination such as:
10.10.10.*
10.10.10.*.*
10.10.10.0/24
10.10.10.0 /24
10.10.10.0/255.255.255.0
10
Hi folks,
Please advise me on the below:
PC1-PIX--Router--RouterPIXPC2
PC1 = nt-box
PC2 = unix box
framerelay is connected between the two routers
PIX codes are 5.2(6)
My problem is that when I initiate a telnet session to PC2(
I had similar problem with the 4500/4700 series router. My problem was
that during air shipping, the routers were bouncing up and down. As a
result of this, the cpu became kinda lose. So I opened up the router,
took out the cpu and tightly inserted it back in. Voila, I got something
when I boo
Hi guys,
I need to swap for a date in December of 2001 or early January of
2002. Please contact me offline. I appreciate it.
-Frank
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=23447&t=23447
--
FAQ, list archives, and subsc
Hi guys,
Usually, on a cat3524-xl or cat2924-xl series switches, I can look at the
stats on how much bandwidth is being used on each port by sh int
fast0/1. Let's say I want to do the same on a cat5500, looking for how
much bandwidth is used on port 2/10. What is the same command? I can't
seem
Hi guys,
I appreciate for any input here. I'm trying to sniffer a specific port
that AIM(america online instant messenger) uses, which is 5190/tcp. I'm
currently using network associates sniffer pro version 3.5. Since there
wasn't a tcp/5190 port in the filter, I went into
Tools--->Options--->P
Try showing full header on the email. You might be able to dig it out
from the X-originating IP.
Cheers,
Frank Kim, Manager
Sales and Marketing
Loud Packet, Inc.
26755 Jefferson Ave. Suite F
Murrieta, CA 92562
Direct: 909-757-5119
Office: 909-894-8240 ext. 8010
Fax:909-494-4425
Email
100 matches
Mail list logo