Note: The K3/K3S Programmers Reference specifically states that the FA;
command (change frequency) requires 0.5 seconds when changing bands and
that *all command handling is deferred until the process is complete*.
I don't know if band changes enter into the equation for you but if an
earlier v
I will amend the above:
It is not the fault of MY K3.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: ht
Got it! It was suggested in an email that I install an old version of
HRD. I did that (5.24.xxx) and sure enough - all is working just fine now.
Question is:
Is it the fault of a Windows update?
Is it the fault of an updated version of HRD.
Fact is:
It is not the fault of the K3!
The jury
Also have noticed that when using the K-Pod to QSY:
HRD is very slow to report the current frequency and cannot keep up with
the VFO. The K3 display works properly with the K-Pod.
Bill W2BLC K-Line
__
Elecraft mailing list
Home: http
Bill,
Please let me know if you see slow comms between the K3 and otehr
programs. I am seeing that in some cases.
73s and thanks,
Dave (NK7Z/NNR0DC)
https://www.nk7z.net
ARRL Technical Specialist
On 08/10/2018 09:41 AM, Bill wrote:
I have tried and tested everything mentioned and a load more
I have tried and tested everything mentioned and a load more. Results:
Primary Computer is solid - working properly
Laptop using a converter to RS232 - also working properly
HRD performs properly with my TS480 with either computer
HRD fails with the K3 on either computer (symptoms already discuss
Bill,
Have you looked at the RS232 menu to check the baud rate?
If you have a P3 check that too.
Set it for 38400.
73,
Don W3FPR
On 8/8/2018 4:34 PM, Bill wrote:
Suddenly, HRD is no longer working with my K3:
Using my K3, I initially click on a favorite - the rig responds
immediately. After
Hi,
I too have had issues with the serial port speed of my K3 as well. My
issues are when using MixW though, not HRD. When I switched from my
Icom 756 PROIII to the K3, (using MixW), I was appalled at the loss in
speed for rig control. I have never fully resolved this issue, and will
be mo
Just a thought, try disabling windows
defender when you are having this issue.
Settings >
Update & security >
Windows Security >
Virus & threat protection >
Virus & threat protection settings >
Turn Real-Time protection off
If nothing changes then it's not defender
behind the problem.
If t
same.73 Tomva2fsq.com
Sent from my Samsung Galaxy smartphone.
Original message From: Bill Date:
2018-08-09 12:13 AM (GMT-05:00) To: elecraft@mailman.qth.net Subject: Re:
[Elecraft] HRD slow accessing K3 frequency controls
Computer has a serial board with two ports. One for the
All are good suggestions and I have tried them all. No difference noted.
I run Malwarebytes and trust it. I do good cleanings periodically.
The older SSD I tried was used as the primary C drive while testing - no
other drives plugged in. No changes there either.
What is strange is the fact th
Also there are applications that will remove scraps of updates, faulty
files, excessive Registry entries and such. Sounds like time to do
some in-depth computer house cleaning. Also, a virus or malware will
consume resources and really bog down a computer basically doing nothing.
I use a
Can you try the K3 utility and talk directly to the K3 and eliminate HRD
from the picture? You could try the Windows and Linux versions and compare
operation. Someone else may have to suggest what operation would exercise
the interface. I would NOT try a firmware upgrade, try something innocuous
th
Bill,
Have you run the Windows Task Manager to see if the cpu, disk and/or memory
is being heavily utilized; stuck at 100% or thereabouts on a regular basis?
Ken
WA2LBI
On Thu, Aug 9, 2018 at 12:13 AM, Bill wrote:
> Computer has a serial board with two ports. One for the K3 (P3) and one
> f
Computer has a serial board with two ports. One for the K3 (P3) and one
for the 480. Not used for anything else. No adapters.
Pulled a two month old backup SSD out of the safe. No go - did not work
then either.
I am sure the computer is busy doing something - which I don't know
about - causi
Bill,
Aren't computers fun? If it is a Windows update, there will be a restore
point to go back to. Click on the Windows icon in the lower left corner
of your screen and type 'restore' and you can find the latest restore
points with their dates. Try going back to the latest one.
Some other q
Suddenly, HRD is no longer working with my K3:
Using my K3, I initially click on a favorite - the rig responds
immediately. After a few seconds (less than 10), I click on another
favorite and there will be a multi-second delay (about 6 or 7 seconds)
before the change takes place. Changing band
A full reinstall of Win 10 was made and the problem went away. The only
thing changed on my Windows system is the updates (no control over them).
Bill W2BLC K-Line
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/
15:49:37 -0500
From: Bill
To:elecraft@mailman.qth.net
Subject: [Elecraft] HRD question
Message-ID:<56ce1761.6030...@nycap.rr.com>
Content-Type: text/plain; charset=utf-8; format=flowed
Has any one experienced a distinct slowdown of HRD initiating on Win 10?
I just put a Win 10 drive on my co
SSDs should not need de-fragmenting.
The problem with fragmented disk volumes is that the parts of a file get
scattered all of the disk. That means it takes multiple seeks to get an entire
file. De-fragmenting organizes each file in neighboring blocks on the same
cylinder, so the file can be ac
15:50
To: elecraft@mailman.qth.net
Subject: [Elecraft] HRD question
Has any one experienced a distinct slowdown of HRD initiating on Win 10?
I just put a Win 10 drive on my computer from about six weeks ago and it
initiates in about six seconds. On the current Win 10 drive, it takes about
25
I have never purchased - still using the same version for years. Hence,
no calls to your support. But, thanks for the offer.
That said, I really do not feel this is an HRD issue - more like
something leaking in from Windows 10 and a faulty update. Else why the
huge difference using a version o
Have you talked to my support staff?
Rick - W4PC
http://tickets.hrdsoftwarellc.com
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill
Sent: Wednesday, February 24, 2016 3:50 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] HRD question
Has
Identical SSDs. Never defrag same! Only difference is the one is up to
date and the other is out of date by about four weeks.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mm
l.com
10-10 #74624, North Georgia Chapter #2038
PODXS 070 #1962
K3# 281, P3 #688, KAT500 #860, KPA500 #1468
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill
Sent: Wednesday, February 24, 2016 3:50 PM
To: elecraft@mailman.qth.net
Subject: [Ele
Has any one experienced a distinct slowdown of HRD initiating on Win 10?
I just put a Win 10 drive on my computer from about six weeks ago and it
initiates in about six seconds. On the current Win 10 drive, it takes
about 25 seconds. The only difference between the drives is that the
slower dr
att Zilmer [mailto:mzil...@roadrunner.com]
Sent: Saturday, August 8, 2015 10:28 AM
To: la...@rn.org
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] HRD and K3
>
>The K3 goes into transmit but there is no power coming out of the radio.
>
Problem areas to look for -
1. The K3 mode shou
On 8/8/2015 2:31 PM, Lyle Johnson wrote:
In addition to Joe's excellent advice, you may need to set the Tx output
level for the soundcard in DM780 to a higher-than-default level. In the
DM780 version I have on my computer, I have the Transmit Level sliders
for Master and Wave both set to about
In addition to Joe's excellent advice, you may need to set the Tx output
level for the soundcard in DM780 to a higher-than-default level. In the
DM780 version I have on my computer, I have the Transmit Level sliders
for Master and Wave both set to about 70.
With that, my K3 (S) LINE (IN) gain
Hi to the gang
I have to agree with all the advice from the other hams but I have experienced
one more thing at least with my KX3. If I keep turning up the audio the
indications go up to the required 4 to 5 bars than if I keep turning up the
audio all the bars go away. I can see with a mic gain
>
>The K3 goes into transmit but there is no power coming out of the radio.
>
Problem areas to look for -
1. The K3 mode should be TX DATA (seen on the graphic), and its data
mode should be DATA A. DATA A is used to interface external sound to
the K3 through line in and out jacks.
2. Line in an
> Any other ideas??
Are you using MODE=DATA and data sub-mode=DATA_A?
> MIC SEL was set to Line In I changed it to FP
>
> MIC+LIN was set to NA and I set it ON and the MIC level is set to 60.
Set MIC+LIN back to OFF, set Mic SEL back to Line In, place DM780 in
PSK31 transmit and adjust the Mic
I don't use HRD, but the configuration should be basically the same
regardless of which software you use. My guess as to what was wrong
initially would be sound card output level too low or muted, but since
then you have made changes in the wrong direction.
First, you didn't mention which mode
I have my K3 connected to the PC and the K3 software works fine.
I have 2 audio cables between Line IN and Line Out of the K3 to the Mic and
Speakers on the PC.
With HRD - I see the QSOs on the screen and of course the waterfall display
at the bottom with an Audio level of 10%.When I at
To populate the logging window with a call sign shown in the receive window,
just right-click on it and DM-780 should copy in the call and do the lookup.
73,
Roger
N5RWK
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/list
ail.com
> 10-10 #74624, North Georgia Chapter #2038
> K3# 281, P3 #688, KPA500 #1468
>
> -Original Message-
> From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Paul
> VanOveren
> Sent: Wednesday, November 12, 2014 9:56 AM
> To: elecraft reflecto
12, 2014 9:56 AM
To: elecraft reflector
Subject: [Elecraft] HRD DM780 QUESTIONS
Just getting back into psk and everything working ok, except cannot remember
settings to populate the Add Log Entry window with the call signs that
appear in the receive window. I want to be able to click on a statio
Right mouse click on it.
Gerald
On Nov 12, 2014 8:56 AM, "Paul VanOveren" wrote:
> Just getting back into psk and everything working ok, except cannot
> remember settings to populate the Add Log Entry window with the call signs
> that appear in the receive window. I want to be able to click on
Just getting back into psk and everything working ok, except cannot
remember settings to populate the Add Log Entry window with the call signs
that appear in the receive window. I want to be able to click on a
stations call sign that is calling CQ and have the call sign appear in the
log entry win
Folks,
I want to thank _/*ALL*/_ of you who sent feedback!!! I narrowed the
issue I was having with the RX
down to the the following:
a) The SQUELCH default (25%) was simply too high. I lowered it to 4%
b) For some interesting reason, I had to drop the audio input down to
about 15%. This level
Tony
You said you used fldigi or some other software before.
Did you run Olvida? If so then hardware fine its a HRD setting.
Confirm that and I will go check mine in that mode while waiting.
Gerald
__
Elecraft mailing list
Home: http://mai
Looking at what I sent, I got Line In and Line Out reversed.
Tony is having problems decoding, so the Soundcard Line In and the K3
Line Out are the ones that are to be moved to the computer built-in
soundcard.
73,
Don W3FPR
Tony,
First make sure t
Tony,
First make sure that you have a good audio connection from Line Out to
the soundcard. Use good quality cables that do not pick up noise.
What happens if you eliminate the Signalink - change HRD to use the
computer default soundcard and connect from that soundcard line out to
the K3 Li
Hi Sal,
Yes, I went through the Signalink audio level config again and no change.
The Signalink pots are also set just like yours.
73,
Tony L. (KJ5XF)
Hi Tony!
Have you gone through the Signalink audio levels config procedure?
Is it possible that its just Windows audio levels that are low?
All m
Hi Steve,
I had the slider at about 25% and I moved it all the way to the left.
Still no change.
73,
Tony L. (KJ5XF)
Tony…
There is a SQUELCH slider near the top above the receive window (grayish
horizontal bar moving). My slider was in the middle and when I moved the slider
to the left al
Hi Gerald,
My K3 is indeed set to Data Mode. The bandwidth is set correctly and I
also have the default settings.
I also have re-installed HRD/DM780 I also re-checked the Signalink
soundcard settings and they are OK.
Still no go... TX is fine, RX drops characters.
73,
Tony L. (KJ5XF)
Tony…
There is a SQUELCH slider near the top above the receive window (grayish
horizontal bar moving). My slider was in the middle and when I moved the slider
to the left all the way, I had solid copy. Where is yours set at?
73, Steve K6SAB
On Jun 24, 2014, at 6:47 PM, Tony Lyon wrote:
> Fo
Tony
I have the same setup.
I have not tried Olivia. I have worked all other modes.
What mode is radio set too? Data mode? Is the decode button highlighted
above the waterfall in DM780?
Is band with set properly as not to cut off the signal edges both on the K3
and DM780?
Once your on the signal ba
Folks,
I decided to try HRD/DM780 for first time after using another HF digital
software program for
probably 10 years. I am using an Elecraft K3 and a SignaLink USB
interface and both
MixW and MultiPSK fine with ZERO problems on either RX or TX. With
HRD/DM780 (version 6.2) the K3
will TX
Thanks for the response - and no, I never received any email from you
regarding this question.
There are no sliders for Lo cut and Hi cut (they are separate controls
on the K3 from Shift and Width and function differently).
The other slider I asked about was for the Manual Notch - not the NB.
to test
it, but 6.2 is in beta and ONLY for paid users until it's release.
Rick - W4PC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of AA6VO
Sent: Wednesday, March 19, 2014 4:16 PM
To: elecraft@mailman.qth.net
Subject:
Thank you very much for making those tests. They saved me the
frustration of purchasing the new version of HRD, that would not have
improved my operation.
I only use HRD for rig control, so my best bet now is to keep using the
5.xx version that I already have set up.
Bill W2BLC K-Line
__
Hello Bill,
I have HRD 6.2.3.234 current Public Beta and took a look at your questions:
ATU button works (AUTO/BYPASS) but button does not light
ATU Tune button works but no light
Notch (AUTO/OFF) works but no light
Notch-Manual button exists but does not allow for manual adjustment as far
as I c
Thanks for the general information. I did go to their site and could
find nothing directly addressing my questions.
What I am looking for, is someone actually using the latest version of
HRD with a K3 that can answer my questions from experience.
Thanks,
Bill W2BLC K-Line
__
The KX3 is 'officially' supported with HRD version 6.2, I believe. If you're
running any of the 5.x releases, you're actually running as a K3 since the 2
command sets are so similar. Both K3 and KX3's button mapping has improved
with 6.x, too.
Check with the HRD folks on the details - especially
I am using HRD 5.xx for rig control. I would like to buy the new version
6.2 if it will do the following:
Light the buttons for: ATU, ATU Tune, Notch, Notch Manual, Noise Blanker
Provides sliders for: Manual Notch, Hi Cut, Lo Cut
Any K3 users with the latest HRD to answer? I have asked before an
Absolutely textbook example of common mode (conducted) RFI on the
antenna cable. See the K9YC and GM3SEk documentation on common
mode chokes. In your case, I'd suggest one at the remote tuner
and one at the ground rod where your feedlines enter the shack.
The problem occurs because the RF volt
Anyone having this problem?
This is everything I can think of:
When running digital, my computer looses contact with my
K3/P3/KPA500/KAT500. In other words, DM780 stops working necessitating
shutting down HRD, pulling and re-plugging in the USB connection,
restarting HRD. Sometime the K3 is loc
The PC in my shack crashed badly, and I had to start again from
scratch. Does anyone, off hand, know the settings for Ham Radio
Deluxe (5) for controlling the radio in DM780. I receive fine, but I
don't key the K3 when I want to transmit.
Thanks in advance,
73, Dick WO1I
__
I have a kx3. I may have the wrong usb driver so tonight I plan on
downloading it again and see if that works. Thanks for all the advise.
--
View this message in context:
http://elecraft.365791.n2.nabble.com/HRD-software-tp7572114p7572126.html
Sent from the Elecraft mailing list archive at
Since you are using VMware, you have to ensure that USB/Serial is supported
or enabled by the hypervisor. I know it is now available in Hyper-V, not
sure about VMware though.
--
View this message in context:
http://elecraft.365791.n2.nabble.com/HRD-software-tp7572114p7572123.html
Sent from the
K2, K3, or KX3? Which transceiver are you using.
If a K2, many USB to serial adapters do not like to run reliably at the
K2s 4800 baud. Try a real serial port or another adapter.
73,
Don W3FPR
On 4/2/2013 8:06 PM, AB1SX wrote:
I just installed the HRD software using windows and VMware on a
Did you install the KXUSB driver?
Via the Elecraft site
http://www.ftdichip.com/Drivers/VCP.htm
- Original Message -
From: "Gary K9GS"
To:
Sent: Tuesday, April 02, 2013 5:13 PM
Subject: Re: [Elecraft] HRD software
I suggest asking on the HRD reflector. I'm guess
I suggest asking on the HRD reflector. I'm guessing someone has done
what you're trying to do.
On 4/2/2013 7:06 PM, AB1SX wrote:
I just installed the HRD software using windows and VMware on a mac. The
windows and HRD all loaded fine. I get to the connecting screen and it
attempts to make a
I just installed the HRD software using windows and VMware on a mac. The
windows and HRD all loaded fine. I get to the connecting screen and it
attempts to make a connection but comes back with a message stating can not
find frequency, com failled and to make sure radio is switched on. I tried
i
Try the HDR Support Forums
http://forums.hrdsoftwarellc.com/
Mike Alexander - N8SMA
amsct...@comcast.net
- Original Message -
From: "Scott W2NTV"
To: "elecraftyahoo" , "elecraft"
Sent: Saturday, February 16, 2013 6:27:22 PM
Subject: [Elecr
has anyone had a problem running the Logbook from HRD... "locks up"
after logging a qso...other things too, but that's the big one
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.q
After multiple restarts of DM780 I finally closed all the software and
rebooted. That resolved the incorrect "worked" markers I was experiencing.
I found a second issue that all of the macros were set back to the defaults
and I had to edit them. The software wouldn't let me edit. After being
annoy
Downloaded it yesterday. I don't notice any significant differences. Still
working just fine with my K3
John KE4D
Fort Clark Springs, Texas
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://ma
I also had the problem with DM780 freezing the machine. Actually, the
problem was traced to the serial/USB interface that I was using.
Specifically, the Proset chip set was used in that interface, which is
known to have problems. I switched to a serial/USB interface based on
the FTDI chip set a
Was it not the case that Simon sold his K3 and bought a FT950? That would
explain the enhanced support for that radio.
As for HRD under new ownership, I shall be interested to see what the new
commercial version (due to be released at Dayton I think) will offer. I
have no problem with paying for
I just uploaded the new HRD and it has very few controls for the K3. In
comparison, I had before a FT950 and it had probably fifty plus slider bar
options. It worked real well with the 950 for basic rig control minus the fact
that I never had good stable operating of DM780 which is a application
Does the current "free" version of HRD do anything additional for the K3
than previous versions? Perhaps allow more sliders or other controls?
Bill W2BLC
--
IN GOD I TRUST (but, NOT a single politician)
__
Elecraft mailing list
Home: h
gt; http://www.dh8bqa.de/
>
>
>
>
> - Original Message -
> From: "Joel Black"
> To: "elecraft"
> Sent: Thursday, April 05, 2012 11:26 PM
> Subject: [Elecraft] HRD Turning Off AGC
>
>
>> Has anyone else encountered HRD turning *off* thei
Doh! I just read that too on the reflector in the past week. I
completely forgot about it. Thanks for the reminder.
Joel - W4JBB
On 4/5/2012 4:33 PM, Oliver Dröse wrote:
> Hi Joel,
>
> this is a known issue of HRD. Wayne added some code in the K3 firmware
> to suppress that miss-behaviour of
;Joel Black"
To: "elecraft"
Sent: Thursday, April 05, 2012 11:26 PM
Subject: [Elecraft] HRD Turning Off AGC
> Has anyone else encountered HRD turning *off* their AGC? I've had it
> happen twice in the past day. The first time, it really had me chasing
> my tail un
Has anyone else encountered HRD turning *off* their AGC? I've had it
happen twice in the past day. The first time, it really had me chasing
my tail until I noticed the K3 display. The second time, I was looking
for it.
I've also had my DATA MD change on me on two bands without me doing it,
Never mind...I just found the answer on the HRD Yahoo site. I needed to set
the K3 VFO-IND to YES. Geesh!
..mike AI6II
--
View this message in context:
http://elecraft.365791.n2.nabble.com/HRD-K3-band-switching-issue-tp7301947p7301965.html
Sent from the Elecraft mailing list archive at Nabble.co
I have always had a problem with the K3/HRD Cluster interface regarding band
switching. If I select a DX spot for a different band, the K3 'clicks' and
momentarily show the new band/frequency on the VFO, but then immediately
returns to where it was. If I am already on the band there is no problem.
David, I upgraded to the new HRD last week. I'm running a K3 and a KPA500 and
also a SteppIR vertical. All are working just fine with the newest version of
HRD. No issues at all. I'm running the same configuration as you, different com
port but that shouldn't matter.
John KE4D
Message:
I used HRD for quite a while with my K3 and had absolutely no problems. It
works fabulously, especially if you are still using real serial ports.
Hope this helps.
73,
Ian Kahn, KM4IK
Roswell, GA
km4ik@gmail.com
K3 #231, P3 #688
On Jan 14, 2012 3:21 PM, "W2BLC" wrote:
> I have been using H
I have been using HRD for several years for rig control of my current
XCVR and have become very accustomed to it and wish to continue its use
with the K3. Hence, the question:
Are there any issues using HRD for rig control of the K3? I have no
plans for digital word, so DM780 is not included in
Yes I am using the Y cable. I have to run none Ham errands for the XYL so the
radio must wait. Martin N1KGP
Sent from my iPhone
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net
All polling for freq has to be by the logging program.
>
> 73 Larry K1ZW
>
> -Original Message-
> From: elecraft-boun...@mailman.qth.net [mailto:
> elecraft-boun...@mailman.qth.net] On Behalf Of Martin
> Staffa
> Sent: Sunday, July 31, 2011 9:29 PM
> To: Elecraft@ma
Behalf Of Martin
Staffa
Sent: Sunday, July 31, 2011 9:29 PM
To: Elecraft@mailman.qth.net
Subject: [Elecraft] HRD N1MM
I have tried both and if I leave the computer alone for a while every thing
comes to a halt and I can not work the radio I also have steppIR in the mix.
I have to restart the computer
Your computer is probably turning off the USB port to save power.
You will need to change the power saving settings in both the
power control menu and Windows Device Manager.
73,
... Joe, W4TV
On 7/31/2011 9:28 PM, Martin Staffa wrote:
> I have tried both and if I leave the computer alone
I have tried both and if I leave the computer alone for a while every thing
comes to a halt and I can not work the radio I also have steppIR in the mix.
I have to restart the computer to unlock the program no matter if its HRD or
N1MM
__
E
If you are talking about rig control you have to run HRD. When you first
run it you will get a connection screen. Set up your COM port there and
connect.
Then in DM780 for PTT you probably want to click connect through HRD. When
the Radio window is open in DM780 click connect.
73
Greg
AB7R
On
n7za wrote:
> Anyone using Ham Radio Deluxe with the K3 for PSK31?
>
> I loaded it and clicked on DM780. The only thing I see is to set it up
> with a sound card.
>
> How do you set it up to talk with the serial port? The radio controls
> work OK.
You don't. AFAIK the only software that will us
Anyone using Ham Radio Deluxe with the K3 for PSK31?
I loaded it and clicked on DM780. The only thing I see is to set it up
with a sound card.
How do you set it up to talk with the serial port? The radio controls
work OK.
tnx
Bruce Kennewick, WA n...@arrl.net 509/396-3082
___
I see some discussion of this topic in the past, but did not see a solution
to my situation. Hoping someone can point me in the right direction.
Hardware is an HP Pavilion mini-tower with dual-core processors. I have
added a half-height Perle card that gives me two "real" serial ports. It
ca
On Mon, Oct 26, 2009 at 6:28 PM, Frank MacDonell wrote:
> I just loaded up the 3.44 K3 utility which I am using with the latest
> version of HRD and my K3. Using HRD to key the radio, I noticed the
> red transmit light does not illuminate during CW. Does this sound
> correct?
No... I'm fairly sur
I just loaded up the 3.44 K3 utility which I am using with the latest
version of HRD and my K3. Using HRD to key the radio, I noticed the
red transmit light does not illuminate during CW. Does this sound
correct? Thanks in advance.
--
Sent from my mobile device
Frank KD8FIP
_
I think I can prevent this with a change to K3 firmware. If so, I'll
get another beta version out as quickly as possible.
Wayne
N6KR
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.q
OE5CSP-Chris wrote:
>
> We habe been trying to use HRD with the K3 but the program shuts down
> after some seconds. I use Windows Vista. The K3 is connected to the
> program in the beginning(I can read the K3´s frequency), but then stops
> working(blue screen). We believe that the USB to serial
Here is Simon´s answer to my problem. Does anybody know where to get
prolific drivers which will work with Ham Radio Deluxe?
73, Chris-OE5CSP
Hi,
If you get a BSOD (Blue Screen Of Death) then it's the driver for the
Prolific cable which must be updated, only drivers can cause a BSOD and with
We connected the K3 to another computer running XP and after a while
everything was doing fine. I´ll contact Simon today and let you now the
answer. Thanks for your replies!!!
73, Chris-OE5CSP
--
View this message in context:
http://n2.nabble.com/HRD-shuts-down-tp3004924p3010492.html
Sent fr
Make sure you use a FTDI Serial Cable that has a real RS-232 Port built in
> http://www.ftdichip.com/Products/EvaluationKits/USB-Serial.htm
> When I bought this cable all my Serial port nightmares ended in Linux,
> BSD,
> MAC OS X and Windows 32 OS systems.
>
>
>
> In Windows Vista make sure
: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of OE5CSP-Chris
Sent: Sunday, May 31, 2009 11:43 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] HRD shuts down
We habe been trying to use HRD with the K3 but the program shuts down after
some seconds. I use
We habe been trying to use HRD with the K3 but the program shuts down after
some seconds. I use Windows Vista. The K3 is connected to the program in the
beginning(I can read the K3´s frequency), but then stops working(blue
screen). We believe that the USB to serial cable is causing troubles, but o
1 - 100 of 144 matches
Mail list logo
