RE: post CCIE written clarification
Charles, I'm currently struggling with the same... (I'm taking BSCN this Tuesday) here's the def's from the Cisco press BSCN course book. Point to Multipoint - treats the nonbroadcast network as a collection of point to point links. NBMA - Emulates a broadcast network, usually used in a fully meshed environment, some configuration necessary and for good measure an RFC: RFC 2328 Congrats on the written, Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Charles Henson > Sent: Wednesday, January 24, 2001 6:29 PM > To: [EMAIL PROTECTED] > Subject: post CCIE written clarification > > > Got the written out of the way and am now going back to the basics to help > start preparing for the lab. One thing I cannot get clear and > can't find any > good references for on CCO is the difference (if there is one) > between point > to multipoint and nbma topologies. I have discussed this at length with my > peers and am still drawing a blank. If anyone can clarify this or > refence a > good URL it would be greatly appreciated. Thanks. > > > Charles > [EMAIL PROTECTED] > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: need advice [3:1149]
Where in NJ? Some areas are more expensive than others. A good indication of cost of living can be found in the real estate section of yahoo.com (look in classifieds). If I remember correctly, car insurance is also expensive in NJ. Hope that helps, Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Mihai Dumitru > Sent: Thursday, January 25, 2001 11:34 AM > To: [EMAIL PROTECTED] > Subject: need advice [3:1149] > > > Hi! > > > I was offered o job in New Jersey area, through a recruiter, with H1B > visa sponsorsip. > > I finished my academic studies last year, but I have 2 years overall > experience (almost two years in administering a mid-sized NT network, > and half-year in designing and implementing WAN networks). I am a MCSE, > CCNA (plus Remote Access and Support exams passed), and CCDA. > > The question is: what salary should I ask? In general, will my non-US > experience count? > > It is easy to get a job in Romania with my skills, but I read Jeongwoo's > posting and the replies. It seems it is not so easy to get a job in US > now, at the entry level. I am seriously thinking about staying in > Romania for another year, because here I have a great opportunity to > learn. > > What do you think? > > Best wishes, > > Mihai > > > > > Message Posted at: > http://www.groupstudy.com/form/read.php?f=3&i=1149&t=1149 > -- > To unsubscribe from the Jobs list, send a message to > [EMAIL PROTECTED] with the body containing: > unsubscribe jobs _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Passed Switching Exam
I was going to stay out of this, but it is getting weird... I scored a 912 at the beginning of the month sorry for ruining the Stats ;-) Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > gustavo_spadaro > Sent: Thursday, January 25, 2001 7:46 PM > To: Fred Danson; [EMAIL PROTECTED] > Subject: Re: Passed Switching Exam > > > Me too. > I just took the exam last week and got 857 > > - Original Message - > From: "Fred Danson" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Thursday, January 25, 2001 5:30 AM > Subject: Re: Passed Switching Exam > > > > You got 857 on that exam too?? I just took the exam last week > and got 857. > > Also one of the other guys in my CCNP class also got 857. Has anyone out > > there not scored 857 on this exam?? :) > > > > > > >From: Helena <[EMAIL PROTECTED]> > > >Reply-To: Helena <[EMAIL PROTECTED]> > > >To: <[EMAIL PROTECTED]> > > >Subject: Passed Switching Exam > > >Date: Thu, 25 Jan 2001 09:08:46 +1000 (EST) > > > > > >Hi everyone, > > > > > >Last week I sat the Switching exam and passed. I didn't find > it as easy > > >some people said, and only got 857. But I'm happy I passed anyway :o) > > >There were some straightforward questions, but some really hard ones as > > >well, which the answers I thought weren't in the book > (CiscoPress) I was > > >reading. They also asked heaps of questions on LED lights > which I didnt' > > >know. I have a problem with timing myself though, having done my three > > >CCNP > > > > > >Helena > > > > > >_ > > >FAQ, list archives, and subscription info: > > >http://www.groupstudy.com/list/cisco.html > > >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > > Get your FREE download of MSN Explorer at http://explorer.msn.com > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Does anyone know what a "fluke" is ???
I think a 4000 with the fiber option is more than $5k (probably closer to 10k), we paid $5k for a OneTouch series II with fiber and internetworking option. Although it doesn't have any "real" sniffing/decoding capabilities, it did prove invaluable when we had to split a lan and the fiber option sure beats looking for a red-light coming out of the end of your fiber (no, I've never done that; really!). ;-) Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Jon Krabbenschmidt > Sent: Friday, January 26, 2001 9:23 AM > To: 'Traceroute'; Mask Of Zorro; [EMAIL PROTECTED] > Subject: RE: Does anyone know what a "fluke" is ??? > > > By big daddy you mean the 4000 with fiber option?? The 620 is a great, and > indispensable unit for techs and it is very affordable. > > Jon > > -Original Message- > From: Traceroute [mailto:[EMAIL PROTECTED]] > Sent: Thursday, January 25, 2001 10:46 PM > To: Mask Of Zorro; [EMAIL PROTECTED] > Subject: Re: Does anyone know what a "fluke" is ??? > > > We have a "Big Daddy" Fluke at our site (about $5k worth), and we couldnt > live without it... > - Original Message - > From: "Mask Of Zorro" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Thursday, January 25, 2001 12:37 PM > Subject: Re: Does anyone know what a "fluke" is ??? > > > > Fluke makes all sorts of test equipment. They make some great LAN > analyzers > > for troubleshooting network problems. Some of their handheld meters are > > cheap, others are very expensive. Some of them have > functionality that is > > almost like a sniffer. They are great tools! I have used them > in the past > > with much success for isolating faults on LAN segments. > > > > Check them out: > > > > http://www.fluke.com/ > > > > Z > > > > > > >From: [EMAIL PROTECTED] > > >Reply-To: [EMAIL PROTECTED] > > >To: <[EMAIL PROTECTED]> > > >Subject: Does anyone know what a "fluke" is ??? > > >Date: Thu, 25 Jan 2001 13:22:22 EST > > > > > >Is it some kind fo device to test a workstation and where I go to find > more > > >info about it > > > > > >___ > > >To unsubscribe from the CCIELAB list, send a message to > > >[EMAIL PROTECTED] with the body containing: > > >unsubscribe ccielab > > > > _ > > Get your FREE download of MSN Explorer at http://explorer.msn.com > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Does anyone know what a "fluke" is ???
Another great (undocumented) feature, is that when you plug it into the lan with a bogus ip, the firewall folks will call you in a panic cause they can't figure out what is attached to the inside of the lan. I've done this on accident, so I shouldn't call it a feature, I have a tremendous amount of respect for the responsibility network security specialists have. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Larry Ogun-Banjo > Sent: Friday, January 26, 2001 10:12 AM > To: [EMAIL PROTECTED] > Cc: [EMAIL PROTECTED] > Subject: Re: Does anyone know what a "fluke" is ??? > > > Although portable (the OneTouch Network Assistant), the fluke is > a fantastic > tool. You can use it for identifying routers or other devices on your > network,NIC/Hub tests, cable tests, tracking addresses, etc. I > particularly like > its network health test display showing collisions, bad FCS (frame check > sequence) etc. > > > >From: [EMAIL PROTECTED] > >Reply-To: [EMAIL PROTECTED] > >To: <[EMAIL PROTECTED]> > >Subject: Does anyone know what a "fluke" is ??? > >Date: Thu, 25 Jan 2001 13:22:22 EST > > > >Is it some kind fo device to test a workstation and where I go > to find more > >info about it > > > >___ > >To unsubscribe from the CCIELAB list, send a message to > >[EMAIL PROTECTED] with the body containing: > >unsubscribe ccielab > > _ > Get your FREE download of MSN Explorer at http://explorer.msn.com > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Resume Length (was: Certifications on resumes)
My latest incarnation is two and I don't think I'll ever let it go to three... but I'm certainly no authority on the matter ;-) Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Bradley J. Wilson > Sent: Friday, January 26, 2001 6:25 PM > To: cisco > Subject: Resume Length (was: Certifications on resumes) > > > You bring up an interesting topic. I try to keep mine under *four* pages! > ;-) Why four? I dunno, just seemed like a good number, I guess. > I had one > guy ask me, way back when I was starting out: "Your resume's only *one > page*??" Guess it kinda had an effect on me. ;-) > > Anyone else want to chime in? Can we get a bell curve going on what the > average resume length is? > > > - Original Message - > From: Brandon Rose > To: [EMAIL PROTECTED] > Sent: Friday, January 26, 2001 11:59 AM > Subject: RE: Certifications on resumes > > > My only issue with this is I try and keep my resume itself to one > lean, mean > page - though it sometimes goes over a little. > > If I individually included the dozen MS exams I completed and the many > CompTIA exams I both took and acted as a SME for along with > dates, that adds > a lot of paper right there. Same goes for the gigantic protocol, > operating > system, and equipment list some people include. It doesn't leave > much room > to mention job experience/major projects, which is what probably counts in > the long run. > > I don't know where I should stand on the keyword scan vs. "lean 'n mean" > resume issue. Is there a conflict? > > I understand keywords are vital if someone from HR is scanning a > hundred or > so resumes, but at the same time they don't want to read a small > novel with > footnotes and a bibliography. I know most of my MBA friends > would say it's > all about including as many buzz words and acronyms in as little space as > possible. heh > > I wonder what Raymond from the jobs groupstudy list will think? I'll be > sure to bring this up with him when I see him. > > One thing I do agree on is the vast majority of HR personnel have no idea > what the certs mean (but do they mean anything? that's a whole > other topic > right there). > > My $.02, > > Brandon - holder of various acronyms > > > > > -Original Message- > > From: Kevin Wigle [mailto:[EMAIL PROTECTED]] > > Sent: Friday, January 26, 2001 9:41 AM > > To: Ole Drews Jensen; 'Andy'; Craig Columbus > > Cc: netlinesys; [EMAIL PROTECTED] > > Subject: Re: Certifications on resumes > > > > > > I have done something similar as Ole, > > > > On my resume I have a section with a running history of exams > > passed and > > courses taken. If passing an exam completed a certification > > I note that in > > brackets. i.e. - 15 July 2000, CID exam passed (CCDP completed) > > > > On the cover page I only list the "senior" certs from a > > track. The same for > > my business card, the senior certs only. > > > > But on job boards I check off every single cert due to > > searches by HR people > > who may not know/understand the progression. > > > > There was a time when I chided people for putting down > > MCP/MCSE. But I > > didn't figure that HR people wouldn't know the difference - > > they're supposed > > to know the market they're recruiting for... right? > > > > right. > > > > Kevin Wigle > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: BSCN??
I just took the BSCN today and all I used was the Cisco Press book. I read the book and then read it again while creating my own study guide. So far, the Cisco press books have not let me down one bit. If you know them, you will have zero problems on the test. As far as the test itself, in my case, the first two thirds were easy. What I mean by that is no reading in-between the lines or remembering really obscure details were necessary. The last third took as long as the first two thirds. The questions were challenging and required much thought. I scored a 885. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Buri, Heather H > Sent: Tuesday, January 30, 2001 5:55 PM > To: 'William E. Gragido'; 'AndyD'; '[EMAIL PROTECTED]' > Subject: RE: BSCN?? > > > For this exam, would you recommend that the explanation of BGP provided in > the BSCN books is sufficient or would you recommend Basaam Halabi's book, > Internet Routing Architectures, to pass the exam? Also, what book(s) do > people recommend for this exam? > > I currently have the BSCN book by Thomas M. Thomas published by > McGraw Hill > ISBN 0-07-212477-6 and I don't like it. I am only on Chapter 4 but have > already found too many typos in it. I expect a few, but this is > ridiculous. > Can anyone recommend the book by Cisco Press for BSCN? > > Thanks, > > Heather Buri > > > -Original Message- > From: William E. Gragido [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, January 30, 2001 10:12 AM > To: 'AndyD'; [EMAIL PROTECTED] > Subject: RE: BSCN?? > > > No IS-IS, but you must know OSPF configs, EIGRP and BGPv4 like its cool > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > AndyD > Sent: Monday, January 29, 2001 10:49 PM > To: [EMAIL PROTECTED] > Subject: BSCN?? > > > Has anybody out there taken the BSCN test?? How was it?? Were there any > questions on IS-IS? Mostly OSPF and BGP?? > > Thanks, > > AD > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Chat Script and BCRAN
Quoted from the Cisco Press BCRAN book: "A chat script is a string of text that defines the handshaking that occurs between two DTE devices, or between a DTE and its directly attached." Is there a word missing after _attached_ or have I just been reading too much Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Routing table entries
sh ip route shows a routing table entry for a particular network (ie 192.168.1.0) as opposed to traceroute showing the hops to a destination address (192.168.1.1). Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Deloso, Elmer G (WPNSTA Yorktown) > Sent: Friday, February 02, 2001 9:41 PM > To: '[EMAIL PROTECTED]' > Subject: Routing table entries > > > Hi all. > Why is it that one can traceroute to a destination IP address A.B.C.D. > however when you do a show ip route A.B.C.D it says the address is not > on the routing table? I'm getting my routes from an ISP via OSPF which > lists several routes learned from it as an OSPF neighbor. > Comments anyone? > > Elmer Deloso > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Paquet's BCRAN p. 194-195
Too weird, I'm on that page and took a break to read my mail! There is no default route, but there are two static routes, we can only assume that the example is talking about traffic directly addressed to the 192.168.1.0 network (router b) - even though they never say so... consider that a practice question for the test ;-) Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Bradley J. Wilson > Sent: Monday, February 05, 2001 8:06 PM > To: cisco > Subject: Paquet's BCRAN p. 194-195 > > > One thing I'm confused about in Paquet's BCRAN book (1578700914): > > On p. 194/195, it shows a config which allegedly will cause > Cisco-a to dial > Cisco-b whenever any non-FTP or non-Telnet IP traffic comes through. My > question is: given the two dialer map statements, why will Cisco-a call > Cisco-b, and not Cisco-c? Will Cisco-a attempt to call Cisco-b first, and > if that fails, then try Cisco-c? > > Thanks in advance - > > BJ > > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: error on the show port counter on catalyst5505
I had a similar problem to ports 3/7 and 3/8 and it was a duplex mismatch. The ports were set to full but the nic couldn't decide whether to operate at full or half. Hard setting the duplex on the PC's it fixed the problem and made the users VERY happy. They were getting less than a third of the line speed! Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Sim, CT (Chee Tong) > Sent: Monday, February 19, 2001 7:18 AM > To: 'Brant Stevens'; [EMAIL PROTECTED]; Santosh Koshy; > [EMAIL PROTECTED] > Subject: error on the show port counter on catalyst5505 > > > Dear all, > > I did a show port conter command in my catalyst 5505 switches and > result as > below. Can I verify with you that whether the below is correct or not? > 1) many Align-Err-FCS-Err counter mean the quality of the cable not good? > 2) many Single/Multi/Late- mean the duplex type not match? > 3)What is the problem if I got many "Runts" and " Giant" counter? > 4)If I got many these port error, will it slow down the whole network or > just the PC attached to the port? > > Port Align-Err FCS-ErrXmit-Err Rcv-ErrUnderSize > - -- -- -- -- - > 1/1 0 0 0 0 0 > 1/2 0 0 0 0 0 > 3/1 0 0 0 0 0 > 3/2 0 0 0 0 0 > 3/3 0 0 0 0 0 > 3/4 0 0 0 0 0 > 3/5 0 3119 0 0 0 > 3/6 57 49 0 0 0 > 3/7 14189 14295 0 0 0 > 3/8 13578 12992 0 0 0 > > Port Single-Col Multi-Coll Late-Coll Excess-Col Carri-Sen Runts > Giants > - -- -- -- -- - - > - > 1/1 0 0 0 0 0 0 > 0 > 1/2 0 0 0 0 0 0 > 0 > 3/1 0 0 0 0 0 0 > - > 3/2 0 0 0 0 0 0 > - > 3/3 0 0 0 0 0 0 > - > 3/4 0 0 0 0 0 0 > - > 3/5 0 0 0 0 0 996 > 0 > 3/6 0 0 0 0 0 7 > 0 > 3/7 0 0 0 0 0 509 > 0 > 3/8 0 0 0 0 0 733 > 0 > > == > De informatie opgenomen in dit bericht kan vertrouwelijk zijn en > is uitsluitend bestemd voor de geadresseerde. Indien u dit bericht > onterecht ontvangt wordt u verzocht de inhoud niet te gebruiken en > de afzender direct te informeren door het bericht te retourneren. > == > The information contained in this message may be confidential > and is intended to be exclusively for the addressee. Should you > receive this message unintentionally, please do not use the contents > herein and notify the sender immediately by return e-mail. > > > == > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Dial-Up Experts...
I've done this with two modems and two computers... not trying to show my age but I connected a Kaypro 2X and a Commodore 128 through their respective modems at 300 baud ;-) Pretty big feat back then... Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Circusnuts > Sent: Sunday, February 25, 2001 3:50 PM > To: [EMAIL PROTECTED] > Subject: Dial-Up Experts... > > > Hey All- is there a way to simulate dial-up without going through the = > Telco (i.e. point to point, using no dial tone). I'm practicing CCIE = > labs & have a few with dial scenario. I wondered it I could do a call = > back without tying up two phone lines, say a modem off of my 2509 = > connected to another modem @ Aux of another router. > > Any advice would be greatly appreciated... > > Thanks > Phil > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: PLEASE HELP !!! Automatic dialing (Second Chance)
I haven't worked with the 800 but here are a few things that can cause unwanted dialing: dns lookups routing table updates ntp time sync Anyone know if the 800 supports NTP?? That or routing updates would be your best bet to get it to dial after a power failure/cycle Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Amnesia > Sent: Wednesday, February 28, 2001 9:54 AM > To: [EMAIL PROTECTED] > Subject: PLEASE HELP !!! Automatic dialing (Second Chance) > > > > PLEASE HELP > > > Hi all !!! > > Has somebody configured a Cisco 800 series > in order to make an "automatic-dial" when the > router has booted up??? > > It must be done without external help as Internet > browsers asking for webpages, mail clients asking > for new mail, etc. I wanna know if it possible to make it > work as soon as possible. I haven't found anything > related to this in cisco web-documentation. > > Anybody can help me ! > > Thank you very much in advance. > > Miguel Angel Romero Arcas > Dpto. Técnica de Sistemas > CESSER Informática y Organización, S.L. > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
IOS Release Schedule
Hi all, There are features in 12.1 that could really help me out but our company policy is to only use GD releases in production equipment. Does anyone have any idea when 12.1 will go GD? Thanks Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Bootstrap replacement
yes, they all use the same one. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Thomas > Sent: Friday, March 02, 2001 3:11 AM > To: [EMAIL PROTECTED] > Subject: Bootstrap replacement > > > Hi Group - I wonder if all the 2500 series routers can use the > same kind of > bootstrap rom? Thanks in advance! > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: image checksum error
I got this same error when I tried to boot an image off of tftp. The image was too big to be both stored in and run from RAM. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Circusnuts > Sent: Sunday, March 04, 2001 2:57 PM > To: Rizzo Damian; [EMAIL PROTECTED] > Subject: Re: image checksum error > > > Bad checksum is produced by corrupt IOS images, incompatible boot ROMs, & > you FLASH that is bad or incompatible (wrong speed in > nanoseconds). You are > right, I doubt the images are bad... > > Phil > > - Original Message - > From: "Rizzo Damian" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Sunday, March 04, 2001 1:08 PM > Subject: image checksum error > > > > I have two 1600 series routers that I am trying to upgrade to a IPsec > > feature set IOS. The problem I am experiencing is no matter > version of the > > feature set I try (I've tried 4 so far), after the image appears to load > > successfuly from a TFTP server, the router displays the message "Image > > Checksum Error" and then procedes to boot from ROM. I have > enough memory, > > flash shouldn't be of concern since I'm booting from a TFTP server. So > what > > gives? Anyone else experience this problem? Is it likely I got 4 bad > images > > from Cisco? Thanks. > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco IOS security flaw
BGP for one > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Watson, Rick, CTR, OUSDC > Sent: Monday, March 05, 2001 5:24 PM > To: [EMAIL PROTECTED] (E-mail) > Subject: RE: Cisco IOS security flaw > > > As you all may have heard about the warning from Cisco concerning > a flaw in > the IOS. It states "the flaw affects the security of only TCP connections > that originate or terminate from the device itself, not any traffic that > passes through the device in transit." > > My question to the group is, can someone elaborate on the types of TCP > connections that would originate/terminate at a Cisco device? I > am sure that > this s an easy answer, but one that puzzles me. Thanks for the help. > > Rick Watson > Network Engineer > OUSD(Comptroller) > 703.697.5710 > [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Telnet to a Router
I have a Netgear and have to specify a default host for a given port. Do you have something similar? My default host for port 23 is my access layer 2501 and I can telnet in from outside of my LAN. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Mark Rose > Sent: Monday, March 05, 2001 6:28 PM > To: Cisco@Groupstudy. Com (E-mail) > Subject: Telnet to a Router > > > > I am trying to telnet to a 2514 router from work. I have a Linksys BEFSR41 > ethernet/dsl router on my incoming cable line. I have enabled port > forwarding for telnet (port 23) on this router. I have also set up vty on > the 2514. When I try to telnet to the wan interface of the > Linksys forwarded > to the ethernet interface on the 2514 I get the message "Could not open a > connection to host: Connection failed". But if I remote access an > NT server > inside my home net (on internal address space), from there I can > telnet (on > the private address space) to the same ethernet interface and connect. > > Since I can remote access my NT box, port forwarding on the Linksys router > is working. Also the 2514 should be set properly since I can > telnet in from > within my lan. I must be overlooking something but I cannot figure it out. > > I would appreciate any ideas or assistance. > > TIA > Mark > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: BCRAN 640-505 Question
That is the latest book and I just used it and passed without a problem last month. It covers everything you need to know. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > udo Konstantin > Sent: Tuesday, March 06, 2001 8:53 AM > To: [EMAIL PROTECTED] > Subject: Re: BCRAN 640-505 Question > > > As I remember, there are big differences between version 1.0 and 2.0 > > Udo > "k w" <[EMAIL PROTECTED]> schrieb im Newsbeitrag > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > hi all, > > > > is studying the Building Cisco Remote Access Network > > book ISBN:1-57870-091-4 by Catherine Paquet enough to > > pass the BCRAN 2.0 series test? i don't think cisco > > has come out with later materials for this exam. so > > essentially, studying from this book prepares you for > > either the 1.0 or 2.0 series tests. Am i correct? > > > > kev > > > > __ > > Do You Yahoo!? > > Get email at your own domain with Yahoo! Mail. > > http://personal.mail.yahoo.com/ > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Telnet question
en conf t line vty 0 4 exec-timeout 15 0 ctrl-z done... Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Stuart Laubstein > Sent: Tuesday, March 06, 2001 12:29 PM > To: '[EMAIL PROTECTED]' > Subject: Telnet question > > > What is the default timeout time for telnet connection a to a > cisco router. > And what is the command to extend this time? I cannot seem to > find either. I > can use the absolute-timeout command but that would also kick someone out > who was working on the router. I just want to set the default > timeout to 15 > mins. > > thanks > > stuart > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: DSL internet with PPPoE
Not that I'm aware of (and I've checked). I have a Netgear RT314 handling the DSL at the core layer (it supports RIP v1+2, and various versions of IGMP) , a 2501 at the distribution layer and a 2505 at the access layer. It all works quite well and I can play with all the routing protocols, redistribution, traffic shaping and set various ACL's at the different layers. As a fringe benefit, my ISP is leaking RIP routes downstream, so now my routing tables are even bigger ;-). This setup has helped immensely in my CCNA and CCNP studies. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Rizzo Damian > Sent: Tuesday, March 06, 2001 4:23 PM > To: '[EMAIL PROTECTED]' > Subject: DSL internet with PPPoE > > > I have a home lab with a few routers and switches, I have a permanent DSL > connection but unfortunately they use PPPoE for authentication. > Is there any > way possible I can use this connection with a Cisco Router??? I'd like to > plug the modem into my router and then route traffic from there. But can't > seem to get past the PPPoE problem. Thanks for the help. > > > > > > > Damian Rizzo > Senior IT Engineer > Marakon Associates > 203-978-6341 > [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: DSL internet with PPPoE
Yes, I think this would work but I don't see how a second PC could get access to the internet unless it used the PC that initiated the connection through the DSL modem as a gateway. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Rahul Kachalia > Sent: Tuesday, March 06, 2001 7:39 PM > To: Rizzo Damian; [EMAIL PROTECTED] > Subject: Re: DSL internet with PPPoE > > > Rizzo, > > I think its possible, following would be your topology > > LAN-switch-Ciscorouter-eth-dsl modem--dsl cloud >( make sure you have to turn ON bridging on > both > ethernet interface of router ) > > I am assuming you are using PPPoE client software on the PC. PPPoE send > Ethernet broadcast which needs to reach to PPPoE server unless > you dont turn > bridging on at routers traffic wont pass & it will fail. > > thanks > rahul. > > > > > - Original Message - > From: "Rizzo Damian" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Tuesday, March 06, 2001 7:22 AM > Subject: DSL internet with PPPoE > > > > I have a home lab with a few routers and switches, I have a > permanent DSL > > connection but unfortunately they use PPPoE for authentication. Is there > any > > way possible I can use this connection with a Cisco Router??? > I'd like to > > plug the modem into my router and then route traffic from > there. But can't > > seem to get past the PPPoE problem. Thanks for the help. > > > > > > > > > > > > > > Damian Rizzo > > Senior IT Engineer > > Marakon Associates > > 203-978-6341 > > [EMAIL PROTECTED] > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: DSL internet with PPPoE
What I was saying is that I don't think (although I haven't tried) that 2 PC's can simultaneously access the same DSL modem, even if you have two accounts. Tim > -Original Message- > From: Rahul Kachalia [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, March 06, 2001 8:48 PM > To: Timothy Metz; Rizzo Damian; [EMAIL PROTECTED] > Subject: Re: DSL internet with PPPoE > > > Tim, PPPoE fundamentals are pretty much similar to PPP over WAN links but > PPPoE breaks the boundary on router/modem & brings down to host > level where > PPP is initiated just like a router but instead of serial links they send > PPP request over Ethernet frame which may add more Layer 2 frame as > configured on router/modem towards dslcloud. > > If second PC need to connect to internet that PC too needs an internet > account & PPPoE software in order to access else first PC can be > multihomed > & provide a gateway service to other host on LAN. > > thanks > rahul. > - Original Message - > From: "Timothy Metz" <[EMAIL PROTECTED]> > To: "Rahul Kachalia" <[EMAIL PROTECTED]>; "Rizzo Damian" > <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> > Sent: Tuesday, March 06, 2001 11:34 AM > Subject: RE: DSL internet with PPPoE > > > > Yes, I think this would work but I don't see how a second PC could get > > access to the internet unless it used the PC that initiated the > connection > > through the DSL modem as a gateway. > > > > Tim > > > > > -Original Message- > > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > > > Rahul Kachalia > > > Sent: Tuesday, March 06, 2001 7:39 PM > > > To: Rizzo Damian; [EMAIL PROTECTED] > > > Subject: Re: DSL internet with PPPoE > > > > > > > > > Rizzo, > > > > > > I think its possible, following would be your topology > > > > > > LAN-switch-Ciscorouter-eth-dsl > modem--dsl cloud > > >( make sure you have to turn > ON bridging > on > > > both > > > ethernet interface of router ) > > > > > > I am assuming you are using PPPoE client software on the PC. > PPPoE send > > > Ethernet broadcast which needs to reach to PPPoE server unless > > > you dont turn > > > bridging on at routers traffic wont pass & it will fail. > > > > > > thanks > > > rahul. > > > > > > > > > > > > > > > - Original Message - > > > From: "Rizzo Damian" <[EMAIL PROTECTED]> > > > To: <[EMAIL PROTECTED]> > > > Sent: Tuesday, March 06, 2001 7:22 AM > > > Subject: DSL internet with PPPoE > > > > > > > > > > I have a home lab with a few routers and switches, I have a > > > permanent DSL > > > > connection but unfortunately they use PPPoE for authentication. Is > there > > > any > > > > way possible I can use this connection with a Cisco Router??? > > > I'd like to > > > > plug the modem into my router and then route traffic from > > > there. But can't > > > > seem to get past the PPPoE problem. Thanks for the help. > > > > > > > > > > > > > > > > > > > > > > > > > > > > Damian Rizzo > > > > Senior IT Engineer > > > > Marakon Associates > > > > 203-978-6341 > > > > [EMAIL PROTECTED] > > > > > > > > _ > > > > FAQ, list archives, and subscription info: > > > http://www.groupstudy.com/list/cisco.html > > > > Report misconduct and Nondisclosure violations to > [EMAIL PROTECTED] > > > > > > > > > > _ > > > FAQ, list archives, and subscription info: > > > http://www.groupstudy.com/list/cisco.html > > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: DSL internet with PPPoE
I guess all we can do is hope for PPPOE support in a future IOS. DSL is a great (and cheap) solution for a SOHO or small branch office. Add a VPN and you're set... but I would guess that until Cisco sees some of the current solutions as a threat to their client base that nothing will be done. This is not a slam on Cisco just how businesses think in general. Tim > -Original Message- > From: Rizzo Damian [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, March 06, 2001 8:59 PM > To: 'Rahul Kachalia'; Timothy Metz; Rizzo Damian; [EMAIL PROTECTED] > Subject: RE: DSL internet with PPPoE > > > I don't see how any of this will provide me with what I desire. I > desire to > plug my DSL modem directly into my router and use that router's address as > the gateway for my LAN. There's no reason that with only ONE registered IP > address that every PC in my LAN can't access the internet. There are many > solutions for this, I would probably use PAT on the router for > instance. The > only thing that stands between me and my desire, is this friggin, useless, > does nothing but supply accounting info to the ISP, waste of > bandwidth of a > protocol, PPPoE! Once you plug the Modem into the router, you somehow have > to authenticate to the ISP PPPoE server with a name and password. > I have not > found a way to implement this yet. This make me mad! > > Thanks for the ideas... > > > > > > -Original Message- > From: Rahul Kachalia [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, March 06, 2001 2:48 PM > To: Timothy Metz; Rizzo Damian; [EMAIL PROTECTED] > Subject: Re: DSL internet with PPPoE > > > Tim, PPPoE fundamentals are pretty much similar to PPP over WAN links but > PPPoE breaks the boundary on router/modem & brings down to host > level where > PPP is initiated just like a router but instead of serial links they send > PPP request over Ethernet frame which may add more Layer 2 frame as > configured on router/modem towards dslcloud. > > If second PC need to connect to internet that PC too needs an internet > account & PPPoE software in order to access else first PC can be > multihomed > & provide a gateway service to other host on LAN. > > thanks > rahul. > - Original Message - > From: "Timothy Metz" <[EMAIL PROTECTED]> > To: "Rahul Kachalia" <[EMAIL PROTECTED]>; "Rizzo Damian" > <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> > Sent: Tuesday, March 06, 2001 11:34 AM > Subject: RE: DSL internet with PPPoE > > > > Yes, I think this would work but I don't see how a second PC could get > > access to the internet unless it used the PC that initiated the > connection > > through the DSL modem as a gateway. > > > > Tim > > > > > -Original Message- > > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > > > Rahul Kachalia > > > Sent: Tuesday, March 06, 2001 7:39 PM > > > To: Rizzo Damian; [EMAIL PROTECTED] > > > Subject: Re: DSL internet with PPPoE > > > > > > > > > Rizzo, > > > > > > I think its possible, following would be your topology > > > > > > LAN-switch-Ciscorouter-eth-dsl > modem--dsl cloud > > >( make sure you have to turn > ON bridging > on > > > both > > > ethernet interface of router ) > > > > > > I am assuming you are using PPPoE client software on the PC. > PPPoE send > > > Ethernet broadcast which needs to reach to PPPoE server unless > > > you dont turn > > > bridging on at routers traffic wont pass & it will fail. > > > > > > thanks > > > rahul. > > > > > > > > > > > > > > > - Original Message - > > > From: "Rizzo Damian" <[EMAIL PROTECTED]> > > > To: <[EMAIL PROTECTED]> > > > Sent: Tuesday, March 06, 2001 7:22 AM > > > Subject: DSL internet with PPPoE > > > > > > > > > > I have a home lab with a few routers and switches, I have a > > > permanent DSL > > > > connection but unfortunately they use PPPoE for authentication. Is > there > > > any > > > > way possible I can use this connection with a Cisco Router??? > > > I'd like to > > > > plug the modem into my router and then route traffic from > > > there. But can't > > > > seem to get past the PPPoE problem. Thanks for the help. > > > > > >
RE: CRC errors on ISDN Interface
I read you original post and just kinda scratched my head. But now that Teunis brought up the building wiring I remember a colleague with the same problem that boiled to an oxidized terminal block in the damp basement of his building. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Tony van Ree > Sent: Tuesday, March 06, 2001 11:06 PM > To: Stephen Robichaud; [EMAIL PROTECTED] > Subject: Re: CRC errors on ISDN Interface > > > Hi, > > There are several places this can break. IF the line tests ok I > can understand this. > > Here is a couple of things you might look at. > > Are the CRC's seen on both ends of the link. (If so then there > is a chance it is on the line side) > > If not then almost certainly the problem will be at the end with > the CRC's between the NT1 and the router. My experience has been > most often this is a cable and/or the comb in the RJ45 socket. > > Another common problem is dry joints in the building wiring. > Often these are not picked up in tests as the voltages used by > test equipment 'blows trhe dust out'. In one case I had it was > indeed water. > > We are really trying to identfy is it in the two wire cct between > the sites or the 4 wire cct within a site. > > > Just some thoughts. > > Teunis > Hobart, Tasmania > Australia > > > > On Tuesday, March 06, 2001 at 01:38:35 PM, Stephen Robichaud wrote: > > > I have a problem with an ISDN circuit that keeps on dropping > off. When I > > look at the BRI interface I see CRC errors. I have swapped out > the patch > > cable going to the providers jack, I swapped out the router and > the ISDN WIC > > but I still keep on getting the CRC errors. The provider has > checked the > > line and they said the line is ok. This router keeps on > dropping off and the > > customer is now getting upset. Any idea have any ideas what I > can check or > > try next? > > > > Thanks > > > _ > > Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > -- www.tasmail.com _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: web based cbt training for ccnp....any good
We have free CBT's at work as well. Personally, I hate them. Sit there for an hour and learn 5 minutes worth of material Just my opinion, some people swear by them. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Moahzam Durrani > Sent: Tuesday, March 06, 2001 11:19 PM > To: [EMAIL PROTECTED] > Subject: web based cbt training for ccnpany good > > > > How effective are the cbt , netg training modules. I get them free through > the organization.Has anybody used them before. I was browsing through the > NETG course for the BSCN and it had some simulations and hands on and also > tried sticking to topics found in the cisco press book., but i > was to tired > looking at a pc screen... ill still stick to the books and hands on labs > Mo Durrani > IS&T > WYSE\EDS > phone:408-473 1246 > [EMAIL PROTECTED] > [EMAIL PROTECTED] > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: DSL internet with PPPoE
Probably should make a new thread but... while we are on the topic.. I've been trying to turn off NAT (I have a Netgear) and pass the traffic to a cisco router and let it do the nat'ing. I've been sucessful in turning off NAT in the netgear but unsuccessful in figuring out how to direct all the traffic to the cisco Just thought I'd through that out there... maybe someone has done it or similiar... Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Rizzo Damian > Sent: Tuesday, March 06, 2001 10:18 PM > To: [EMAIL PROTECTED] > Subject: RE: DSL internet with PPPoE > > > I currently am using a Linksys router. And it works fine, but the firewall > feature (if thats what you want to call it) blows. And it's not very > configurable, (you can only forward ports to one destination). So in a > better world, if I could get my dsl to work through my Cisco > Router, I could > fool around with access-list's, Firewall feature set, NAT, PAT, etc... > > > > > -Original Message- > From: Glenn Johnson [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, March 06, 2001 3:58 PM > To: Rizzo Damian; 'Rahul Kachalia'; Timothy Metz; [EMAIL PROTECTED] > Subject: RE: DSL internet with PPPoE > > > Any reason (other than $) that a simple linksys (<$100) switch wouldn't > allow you to accomplish your goal? > > Sample - > http://www.us.buy.com/retail/product.asp?loc=&sku=10249719&PageFor > mat=7#prod > uct > > It has DHCP, NAT, IPSec/PPTP pass-through, forwarding, etc. All > of this for > what seems like a bargain price. > > I'm not affiliated with Linksys. A Netgear switch would probably > be fine as > well. > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Rizzo Damian > Sent: Tuesday, March 06, 2001 2:59 PM > To: 'Rahul Kachalia'; Timothy Metz; Rizzo Damian; [EMAIL PROTECTED] > Subject: RE: DSL internet with PPPoE > > > I don't see how any of this will provide me with what I desire. I > desire to > plug my DSL modem directly into my router and use that router's address as > the gateway for my LAN. There's no reason that with only ONE registered IP > address that every PC in my LAN can't access the internet. There are many > solutions for this, I would probably use PAT on the router for > instance. The > only thing that stands between me and my desire, is this friggin, useless, > does nothing but supply accounting info to the ISP, waste of > bandwidth of a > protocol, PPPoE! Once you plug the Modem into the router, you somehow have > to authenticate to the ISP PPPoE server with a name and password. > I have not > found a way to implement this yet. This make me mad! > > Thanks for the ideas... > > > > > > -Original Message- > From: Rahul Kachalia [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, March 06, 2001 2:48 PM > To: Timothy Metz; Rizzo Damian; [EMAIL PROTECTED] > Subject: Re: DSL internet with PPPoE > > > Tim, PPPoE fundamentals are pretty much similar to PPP over WAN links but > PPPoE breaks the boundary on router/modem & brings down to host > level where > PPP is initiated just like a router but instead of serial links they send > PPP request over Ethernet frame which may add more Layer 2 frame as > configured on router/modem towards dslcloud. > > If second PC need to connect to internet that PC too needs an internet > account & PPPoE software in order to access else first PC can be > multihomed > & provide a gateway service to other host on LAN. > > thanks > rahul. > - Original Message - > From: "Timothy Metz" <[EMAIL PROTECTED]> > To: "Rahul Kachalia" <[EMAIL PROTECTED]>; "Rizzo Damian" > <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> > Sent: Tuesday, March 06, 2001 11:34 AM > Subject: RE: DSL internet with PPPoE > > > > Yes, I think this would work but I don't see how a second PC could get > > access to the internet unless it used the PC that initiated the > connection > > through the DSL modem as a gateway. > > > > Tim > > > > > -Original Message- > > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > > > Rahul Kachalia > > > Sent: Tuesday, March 06, 2001 7:39 PM > > > To: Rizzo Damian; [EMAIL PROTECTED] > > > Subject: Re: DSL internet with PPPoE > > > > > > > > > Rizzo, > > > > > > I think its possible, following would be your topology > > > > > > LAN-switch-Ciscorout
RE: DSL internet with PPPoE
Oops... This link was something I didn't know about... not the first time I blew my credibility ;-) That's why I love this list!! Thanks Rahul! Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Rahul Kachalia > Sent: Tuesday, March 06, 2001 9:51 PM > To: Rizzo Damian; Timothy Metz; [EMAIL PROTECTED] > Subject: Re: DSL internet with PPPoE > > > Rizzo, > > Check this link > http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/12 > 1relnt/160 > 0/rn1600xg.htm > > but thats for 1605, cisco may comeout for their other 1600 series. > > thanks > rahul. > - Original Message - > From: "Rizzo Damian" <[EMAIL PROTECTED]> > To: "'Rahul Kachalia'" <[EMAIL PROTECTED]>; "Rizzo Damian" > <[EMAIL PROTECTED]>; "Timothy Metz" <[EMAIL PROTECTED]>; > <[EMAIL PROTECTED]> > Sent: Tuesday, March 06, 2001 12:34 PM > Subject: RE: DSL internet with PPPoE > > > > You are correct Rahul. In theory, I do want my Router to be the PPPoE > > client, and have the PC's in my LAN travel through it. I > currently have a > > 1601 and a 1604 router. > > > > > > > > > > -Original Message- > > From: Rahul Kachalia [mailto:[EMAIL PROTECTED]] > > Sent: Tuesday, March 06, 2001 3:15 PM > > To: Rizzo Damian; Timothy Metz; [EMAIL PROTECTED] > > Subject: Re: DSL internet with PPPoE > > > > > > Rizzo, > > > > As I mentioned you earlier I just assumed your PC is PPPoE client, > from > > the following statement looks like you want router to be PPPoE client. > Could > > please tell which is this series of router? > > > > thanks > > rahul. > > - Original Message - > > From: "Rizzo Damian" <[EMAIL PROTECTED]> > > To: "'Rahul Kachalia'" <[EMAIL PROTECTED]>; "Timothy Metz" > > <[EMAIL PROTECTED]>; "Rizzo Damian" <[EMAIL PROTECTED]>; > > <[EMAIL PROTECTED]> > > Sent: Tuesday, March 06, 2001 11:58 AM > > Subject: RE: DSL internet with PPPoE > > > > > > > I don't see how any of this will provide me with what I > desire. I desire > > to > > > plug my DSL modem directly into my router and use that > router's address > as > > > the gateway for my LAN. There's no reason that with only ONE > registered > IP > > > address that every PC in my LAN can't access the internet. There are > many > > > solutions for this, I would probably use PAT on the router > for instance. > > The > > > only thing that stands between me and my desire, is this friggin, > useless, > > > does nothing but supply accounting info to the ISP, waste of bandwidth > of > > a > > > protocol, PPPoE! Once you plug the Modem into the router, you somehow > have > > > to authenticate to the ISP PPPoE server with a name and > password. I have > > not > > > found a way to implement this yet. This make me mad! > > > > > > Thanks for the ideas... > > > > > > > > > > > > > > > > > > -Original Message- > > > From: Rahul Kachalia [mailto:[EMAIL PROTECTED]] > > > Sent: Tuesday, March 06, 2001 2:48 PM > > > To: Timothy Metz; Rizzo Damian; [EMAIL PROTECTED] > > > Subject: Re: DSL internet with PPPoE > > > > > > > > > Tim, PPPoE fundamentals are pretty much similar to PPP over WAN links > but > > > PPPoE breaks the boundary on router/modem & brings down to host level > > where > > > PPP is initiated just like a router but instead of serial links they > send > > > PPP request over Ethernet frame which may add more Layer 2 frame as > > > configured on router/modem towards dslcloud. > > > > > > If second PC need to connect to internet that PC too needs an internet > > > account & PPPoE software in order to access else first PC can be > > multihomed > > > & provide a gateway service to other host on LAN. > > > > > > thanks > > > rahul. > > > - Original Message - > > > From: "Timothy Metz" <[EMAIL PROTECTED]> > > > To: "Rahul Kachalia" <[EMAIL PROTECTED]>; "Rizzo Damian" > > > <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> > > > Sent: Tuesday, March 06, 2001 11:34 AM > > > Subject: RE: DSL internet with PPPoE > > > > > >
RE: DSL internet with PPPoE
t;I guess all we can do is hope for PPPOE support in a future IOS. DSL is a > >great (and cheap) solution for a SOHO or small branch office. > Add a VPN and > >you're set... but I would guess that until Cisco sees some of the current > >solutions as a threat to their client base that nothing will be > done. This > >is not a slam on Cisco just how businesses think in general. > > > >Tim > > > >> -Original Message- > >> From: Rizzo Damian [mailto:[EMAIL PROTECTED]] > >> Sent: Tuesday, March 06, 2001 8:59 PM > >> To: 'Rahul Kachalia'; Timothy Metz; Rizzo Damian; [EMAIL PROTECTED] > >> Subject: RE: DSL internet with PPPoE > >> > >> > >> I don't see how any of this will provide me with what I desire. I > >> desire to > >> plug my DSL modem directly into my router and use that > router's address as > >> the gateway for my LAN. There's no reason that with only ONE > registered IP > >> address that every PC in my LAN can't access the internet. > There are many > >> solutions for this, I would probably use PAT on the router for > >> instance. The > >> only thing that stands between me and my desire, is this > friggin, useless, > >> does nothing but supply accounting info to the ISP, waste of > >> bandwidth of a > >> protocol, PPPoE! Once you plug the Modem into the router, you > somehow have > >> to authenticate to the ISP PPPoE server with a name and password. > >> I have not > >> found a way to implement this yet. This make me mad! > >> > >> Thanks for the ideas... > >> > >> > >> > >> > >> > >> -Original Message- > >> From: Rahul Kachalia [mailto:[EMAIL PROTECTED]] > >> Sent: Tuesday, March 06, 2001 2:48 PM > >> To: Timothy Metz; Rizzo Damian; [EMAIL PROTECTED] > >> Subject: Re: DSL internet with PPPoE > >> > >> > >> Tim, PPPoE fundamentals are pretty much similar to PPP over > WAN links but > >> PPPoE breaks the boundary on router/modem & brings down to host > >> level where > >> PPP is initiated just like a router but instead of serial > links they send > >> PPP request over Ethernet frame which may add more Layer 2 frame as > >> configured on router/modem towards dslcloud. > >> > >> If second PC need to connect to internet that PC too needs an internet > >> account & PPPoE software in order to access else first PC can be > >> multihomed > >> & provide a gateway service to other host on LAN. > >> > >> thanks > >> rahul. > >> - Original Message - > >> From: "Timothy Metz" <[EMAIL PROTECTED]> > >> To: "Rahul Kachalia" <[EMAIL PROTECTED]>; "Rizzo Damian" > >> <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> > >> Sent: Tuesday, March 06, 2001 11:34 AM > >> Subject: RE: DSL internet with PPPoE > > > > >> > >> > Yes, I think this would work but I don't see how a second > PC could get > >> > access to the internet unless it used the PC that initiated the > >> connection > >> > through the DSL modem as a gateway. > >> > > >> > Tim > >> > > >> > > -Original Message- > >> > > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED]]On Behalf Of > >> > > Rahul Kachalia > >> > > Sent: Tuesday, March 06, 2001 7:39 PM > >> > > To: Rizzo Damian; [EMAIL PROTECTED] > >> > > Subject: Re: DSL internet with PPPoE > >> > > > >> > > > >> > > Rizzo, > >> > > > >> > > I think its possible, following would be your topology > >> > > > >> > > LAN-switch-Ciscorouter-eth-dsl > >> modem--dsl cloud > >> > >( make sure you have to turn > >> ON bridging > >> on > >> > > both > >> > > ethernet interface of router ) > >> > > > >> > > I am assuming you are using PPPoE client software on the PC. > >> PPPoE send > >> > > Ethernet broadcast which needs to reach to PPPoE server unless > >> > > you dont turn > >> > > bridging on at routers traffic wont pass &
RE:
http://www.isi.edu/in-notes/iana/assignments/port-numbers > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Heidi white > Sent: Wednesday, March 07, 2001 4:54 PM > To: [EMAIL PROTECTED] > Subject: > > > Anyone know of a site that would list all ports? Or a > specific link on the cisco site? I've looked through > pages upon pages with no luck. > Heidi > > __ > Do You Yahoo!? > Get email at your own domain with Yahoo! Mail. > http://personal.mail.yahoo.com/ > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Spliting Hairs With Frame Relay
I've struggled with that one too... and came to the assumption (there I go assuming again) that when they say "port speed" they are talking about [for example] the physical clock rate between a serial interface and a CSU/DSU. Can someone please elaborate so I shut-up. Thanks, Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Circusnuts > Sent: Thursday, February 08, 2001 7:44 AM > To: [EMAIL PROTECTED] > Subject: Spliting Hairs With Frame Relay > > > > Excess Burst is the maximum # of uncommitted bits that the Frame Relay = > switch attempts to transfer beyond the CIR. My handy dandy BCRAN book = > says the typical Excess Burst is limited to the port speed. The CIR is = > the transfer speed agreed to in bps (DTE clockrate). > > I say all this to say- if my Excess Burst is my agreed CIR (port speed), = > where is the excess... or should I look @ this as point to multipoint = > (many VC's terminating on one interface). =20 > > Any takers ??? > > Thanks > Phil=20 > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CSU+DSU+DTE+DCE+ROUTER=WHAT
> 2. What role does CSU/DSU play? What is the role of DTE/DCE. > A2. The CSU is a device that performs protective and diagnostic functions > for a telecommunications line. The DSU is a device that connects > a terminal > to a digital line. Typically, the two devices are packaged as a > single unit. > The CSU/DSU is usually the DCE (provides clocking) and the router is the > DTE. This may be a bad comparison but it helped me... compare a CSU/DSU to a regular old PC modem. This is the device that sits between your telco line (copper) and the first (or last, depending how you look at it) device that is actually aware of user data. Don't think of a CSU/DSU as either DCE/DTE unless you are stating what the opposing device is, like Santosh did. Yes, the CSU/DSU is DCE to the router. But what about the telco switch it connects to??? A CSU/DSU, like a router can have many ports. In the particular model we have, you can manually set the clock (we're talking telco side) or let it set it's own auto-magically via the line signaling, an external clock, and at least one other option I can't remember at the moment. If you ever connect to the console port of a standalone CSU/DSU you will find quite a few things that need to be set. Luckily most (if not all) of this will be provided to you by the telco. Another point to remember is that a CSU/DSU can be an external device or built-in to the router (or WIC, expansion card, put your term here). Single and dual port models are about the size of a 2500 (1U?) but there are also large multiport models. Ours is used on a fractional T-1, I'm sure if I said something that either doesn't apply or is downright incorrect someone will correct me ;-) (and they should) Hope that helped I'll be out of town for a few days, so flame on ;-) Tim > ""Shubha Sinha"" <[EMAIL PROTECTED]> wrote in message > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > Hi folks, > > I am wondering how do you out together CSU/DSU, DTE/DCE and a router = > > into a neat physical arrangement. I am familiar with each one of them = > > look wise. But that's it. Could someone come forward to explain=20 > > 1. how the physical arrangement is done in a most basic WAN connection? > > 2. What role does CSU/DSU play? What is the role of DTE/DCE. > > 3. Can we set up a WAN connection with just a router not using any of = > > this? > > > > Thanks. > > > > Shubha Sinha > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Old bootstrap verison does not compatible with new IOS
I've heard people from the UK say that Cisco-UK requires an account. I ordered two sets from Cisco-US (ignore my email address) and they never asked but then again, even though I gave my personal address they sent them to my company HQ (because of my CCO registration). my two cents Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Ken W. Alger > Sent: Friday, March 09, 2001 4:43 AM > To: [EMAIL PROTECTED] > Subject: Re: Old bootstrap verison does not compatible with new IOS > > > I never have had to have one. > > ""Thomas"" <[EMAIL PROTECTED]> wrote in message > 9897sa$eq$[EMAIL PROTECTED]">news:9897sa$eq$[EMAIL PROTECTED]... > > Do you need a CCO account for free bootstrap ROM? > > > > > > ""Ken W. Alger"" <[EMAIL PROTECTED]> wrote in message > > 9878hm$881$[EMAIL PROTECTED]">news:9878hm$881$[EMAIL PROTECTED]... > > > You can get new bootstrap version 11.0(10c) free from Cisco + shipping > and > > > handling, look for a number for TAC at www.cisco.com as I forget the > exact > > > number to call. I have also seen some people selling the boot roms on > > ebay > > > for upwards of $120 US. Personally, I like Cisco's deal of $5.00 US > > > shipping and handling better, but that is just me. > > > > > > Ken W. Alger, MCSE, MCT, CCNA, CCDA > > > > > > ""Thomas"" <[EMAIL PROTECTED]> wrote in message > > > 98758c$apv$[EMAIL PROTECTED]">news:98758c$apv$[EMAIL PROTECTED]... > > > > Hi All - I have a 2501 with bootstrap version 4.14. I just upgraded > > > memory > > > > and the IOS to run 12.0. The upgrade was successfually; > however, when > I > > > > reload, I got error message: > > > > > > > > Illegal keyword - 'classless' > > > > > > > > This is because IOS 12.0 have "ip classless" turned on by > default. I > > > wonder > > > > if this old bootstrap version is not compatible with IOS > 12.0? If so > > > where > > > > can I get the latest bootstrap ROM? Thanks All! > > > > > > > > > > > > _ > > > > FAQ, list archives, and subscription info: > > > http://www.groupstudy.com/list/cisco.html > > > > Report misconduct and Nondisclosure violations to > [EMAIL PROTECTED] > > > > > > > > > > > > > _ > > > FAQ, list archives, and subscription info: > > http://www.groupstudy.com/list/cisco.html > > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Passed BCMSN
I took it about 3 or 4 months ago and although I thought it was easy, there were enough ambiguous questions to keep someone (or at least most people, myself included) from scoring in the mid to high 900s. The BCRAN and BSCN I took had practically no ambiguously worded questions. I've heard mixed reviews on CIT, I'll find out for myself later this month ;-) Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Chris Supino > Sent: Friday, March 09, 2001 4:46 AM > To: [EMAIL PROTECTED] > Subject: Passed BCMSN > > > > Passed BCMSN test today with 923. Did anyone else think this test was > ridiculously easy? On to BCRAN. Two down, two to go! Actually question for > all who passed CCIE written: how much more difficult is the > material on that > test as compared to the material on the CCNP/DP foundation tests? > > Christopher Supino > MCSE, MCP+I, CCNA, CNA Netware 5, Compaq ASE > Senior Systems Engineer > TransNet Corp. > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: IP Address Syntax
Isn't it either??? or maybe better said as "used for a network address that doesn't conform to the standard classes" Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Larry Lamb > Sent: Friday, March 09, 2001 6:06 AM > To: [EMAIL PROTECTED] > Subject: Re: IP Address Syntax > > > CIDR as I understand things. Hopefully someone will correct me if I'm > wrong. VLSM allows multiple size networks within the same larger network. > > "David A. Lauer" wrote in message > <006201c0a856$58350f20$890a@DALLAPTOP1>... > > Is it CIDR or VLSM? > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Larry Lamb > Sent: Thursday, March 08, 2001 9:38 PM > To: [EMAIL PROTECTED] > Subject: Re: IP Address Syntax > > > /24 is a CIDR notation. It means that 24 bits are masked leaving > 8 bits for > host addressing. In this case you'd have 192.35.3.0-255 with 0 being the > NetID, 255 being the broadcast ID, and 1-254 being available for hosts. > > "Dennis" wrote in message <989jdk$ths$[EMAIL PROTECTED]>... > I would like to know what the " /24 " at the end of this ip > address means... > 192.35.3.240/24 > > tai > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Switching
I didn't have any ATM and never heard anyone else mention anything about ATM being on BCMSN. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > LeBrun, Tim > Sent: Wednesday, March 14, 2001 4:02 PM > To: [EMAIL PROTECTED] > Subject: RE: Switching > > > I am studying for the BCMSN and I think that is a good book to > recommend but > you will need more. The objectives on Cisco's website include ATM - there > is no ATM in Cisco's book anywhere. > > Tim LeBrun > CCNA, CCDA > [EMAIL PROTECTED] > > > -Original Message- > From: Manny Colon [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, March 13, 2001 11:13 PM > To: [EMAIL PROTECTED] > Subject: Re: Switching > > > I used the Cisco Press Building Cisco Multilayer Switched Networks and > passed. > > Manny > > [EMAIL PROTECTED] wrote: > > > Anyone have any suggestions on books to read for switching exam? > > > > -- > > Get the Latest News at CNN Interactive: http://CNN.com > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco1600 ISDN + D channell
My telecom had announced a service (for consumers) where you had an "always on" D channel that could be used for email only at $5 a month. It never materialized and I have no idea how they would have implemented this on the head end. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Brian > Sent: Wednesday, March 14, 2001 10:58 PM > To: Damien Kelly; [EMAIL PROTECTED] > Subject: Re: Cisco1600 ISDN + D channell > > > I saw that there is isdn technology that allows data to pass along the > always up control channel. If I remember correctly, it passes 8k > along it. > I do not know how commercially available this is. Only use I > could think of > is you could then use it for dial on demand inbound, but do you want that. > > Bri > > - Original Message - > From: "Damien Kelly" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Wednesday, March 14, 2001 7:10 AM > Subject: FW: Cisco1600 ISDN + D channell > > > > Just sending this again, No one commented.. was this a stupid > question to > > ask? > > > > > > > > > > > Is it true that a cisco can be configured to use the D Channell to > > > remotely bring up an ISDN line on a remote router configured > for dial on > > > demand?. > > > > > > I was told sometime ago that a cisco ( also DoD ) could be used to > > > remotely connect to another cisco on a remote network which is on ISDN > > > dialup, using the ISDN D Channell. anyone know if this is true, or > > > possible? anyone have any experience in this? > > > > > > > > > Any suggestions? > > > > > > Thanks > > > > > > Damien Kelly, > > > > > > > > > > > > ** > > The information contained in this message is confidential and > > is intended for the addressee(s) only. If you have received > > this message in error or there are any problems please notify > > the originator immediately. The unauthorised use, disclosure, > > copying or alteration of this message is strictly forbidden. This > > message and any attachments have been scanned for viruses. > > Orbiscom Ltd. will not be liable for direct, special, indirect or > > consequential damages arising from alteration of the contents > > of this message by a third party or as a result of any virus being > > passed on. > > > > > > www.Orbiscom.com > > ** > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Browsing across subnets...
I had the same problem and fixed it with ip helper-address. Your goal here is to get netbios broadcasts forwarded to the destination network. I don't quite remember if the helper address in this case should be the network address or the broadcast address (I'm not at work to check) but someone will correct me if I'm wrong. Network A 192.168.10.X/24 Network B 192.168.20.X/24 on the interface that is directly connected to network A type (config-if)#ip helper-address 192.168.20.0 and on the interface that is directly connected to network B type the opposite (config-if)#ip helper-address 192.168.10.0 > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > The.rock > Sent: Thursday, March 15, 2001 4:52 AM > To: [EMAIL PROTECTED] > Subject: Re: Browsing across subnets... > > > Its also a known problem that Win9x clients are not able to browse across > different subnets...I can't remember the article ID, but if I find it i'll > post it. > > "Rizzo Damian" <[EMAIL PROTECTED]> wrote in message > 49C181ACF35ED311A7DC00508B5AF61102E524E3@NAEXCHANGE">news:49C181ACF35ED311A7DC00508B5AF61102E524E3@NAEXCHANGE... > > Here's an interesting problem...We have two routers on their own subnet, > > with Windows NT and 9x Clients. We setup WINS servers on each subnet to > > resolve Netbios names. On one subnet we can see everyone in network > > neighborhood (both subnets), but on the other subnet, we can only see > > machines on that particular subnet. Both routers are identical in model > and > > configuration. I used the "ip forward-protocol udp 137 & 138" > command, but > > that did nothing. Any thoughts? > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Loggging of router's syslog
Just point both routers at the same syslog server. You can change each routers facility to make it easier to differentiate which is which but I don't think that's mandatory. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Alex Boh > Sent: Thursday, March 15, 2001 11:46 AM > To: [EMAIL PROTECTED] > Subject: Loggging of router's syslog > > > Hi guys, > Is it possible to store 2 routers' event syslog into a > server? If that > is possible, how should I go about it? > > Thanks and regards > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco1600 ISDN + D channell (& PRI D channel nfas)
No it's correct and worth noting that the CCNA answer and CCNP(BCRAN) answers are not the same. Send complaints to Cisco ;-) Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Snow Jr., Jim > Sent: Thursday, March 15, 2001 2:44 PM > To: '[EMAIL PROTECTED]' > Subject: RE: Cisco1600 ISDN + D channell (& PRI D channel nfas) > > > RE ISDN Rates The 192K BRI must be an error, right? > > BRI = 2b (112K) + 1d (16k) = 128K > > US PRI = 23b (1472K) + 1d (64K) = 1536K + 8K framing/overhead = T1 (???) > Eur PRI = 31b (1984K) + 1d (64K) = 2048K (E1) > > Way off, or ??? > > Jim Snow, CCNA > Project Support Engineer > [EMAIL PROTECTED] > > HQ US Central Command > CCJ2-Requirements, Bldg 540 > MacDill AFB, Florida 33621 > (813) 827-6049 > GENERAL DYNAMICS > WORLDWIDE TELECOMMUNICATION SYSTEMS > > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > David Heaton > Sent: Wednesday, March 14, 2001 9:53 PM > To: [EMAIL PROTECTED] > Subject: Re: Cisco1600 ISDN + D channell (& PRI D channel nfas) > > > router(config-if)#isdn x25 dchannel > allowsd isdn on the d channel for a BRI x25 connection IOS 12.1.2 Desktop > > on an e1 PRI ISDN controller you can configure the nfas_d D > Channel timeslot > to be backup, primary or 'none' which permits it to be a B channel > > which should show up under sh isdn serv as an available channel > never actually done it myself > > as for BRI I've never heard of it being don > although you can configure lapb (b channel) variables: > N1Maximum number of bits per I-frame > N2Maximum number of attempts to transmit a frame > T1Retransmission timer > T2Explicit acknowledge deferral timer > T4Keepalive timer > interface-outage Interface outage deadband (partial T3) > k Maximum number of outstanding frames (window size) > moduloSet frame numbering modulus > > has anyone ever configured these variables, & if so to fix what problems? > > also, does anyone know why BRI is represented as 192K total in some books > (I though 2B=2x64 + D =16K) > > US PRI = 23B + 2 D how big is D (54K?) > Europe PRI = 30B + D (64K) > > what would the carrier use for signalling if the D channel was taken? > > Cheer > David > > > >>> "Brian" <[EMAIL PROTECTED]> 03/15 7:57 am >>> > I saw that there is isdn technology that allows data to pass along the > always up control channel. If I remember correctly, it passes 8k > along it. > I do not know how commercially available this is. Only use I > could think of > is you could then use it for dial on demand inbound, but do you want that. > > Bri > > - Original Message - > From: "Damien Kelly" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Wednesday, March 14, 2001 7:10 AM > Subject: FW: Cisco1600 ISDN + D channell > > > > Just sending this again, No one commented.. was this a stupid > question to > > ask? > > > > > > > > > > > Is it true that a cisco can be configured to use the D Channell to > > > remotely bring up an ISDN line on a remote router configured > for dial on > > > demand?. > > > > > > I was told sometime ago that a cisco ( also DoD ) could be used to > > > remotely connect to another cisco on a remote network which is on ISDN > > > dialup, using the ISDN D Channell. anyone know if this is true, or > > > possible? anyone have any experience in this? > > > > > > > > > Any suggestions? > > > > > > Thanks > > > > > > Damien Kelly, > > > > > > > > > > > > ** > > The information contained in this message is confidential and > > is intended for the addressee(s) only. If you have received > > this message in error or there are any problems please notify > > the originator immediately. The unauthorised use, disclosure, > > copying or alteration of this message is strictly forbidden. This > > message and any attachments have been scanned for viruses. > > Orbiscom Ltd. will not be liable for direct, special, indirect or > > consequential damages arising from alteration of the contents > > of this message by a third party or as a result of any virus being > > passed on. > > > > > > www.Orbiscom.com > > ** > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _
RE: Copy an image from TFTP (Windows 2000)
check your tftp server's config... it's not finding the file your router is requesting Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Ash Aslam > Sent: Sunday, March 18, 2001 8:53 AM > To: [EMAIL PROTECTED] > Subject: Copy an image from TFTP (Windows 2000) > > > Hi there, > > I have recently installed Windows 2000 Pro. on my PC and I am having > problems coping an image from the TFTP to Cisco 2509 Router. I can write > the image to a TFTP but cannot read from it. > Initially I had Windows NT 4 and Windows 95 and never had any problems. > > I can ping the tftp server OK: > Router#ping 172.16.10.2 > > Type escape sequence to abort. > Sending 5, 100-byte ICMP Echos to 172.16.10.2, timeout is 2 seconds: > ! > Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms > > Here is what I keep getting: > > System flash directory: > File Length Name/status > 1 9045624 /c2500-js-l.113-11a.bin > [9045688 bytes used, 7731528 available, 16777216 total] > Address or name of remote host [172.16.10.2]? > Source file name? c2500-jos56i-l.121-5 > Destination file name [c2500-jos56i-l.121-5]? > Accessing file 'c2500-jos56i-l.121-5' on 172.16.10.2... > Loading c2500-jos56i-l.121-5 [File not found] > [failed] > > Router# > --- > > If I copy the image from RouterA (TFTP) -> RouterB it copies the > image code > OK. > > Has anyone had similar problems copying the images from TFTP under Windows > 2000 to a Cisco Router? > > Any feedback on how to resolve this issue are welcomed. > > Thanks & Regards, > Ash > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Paper CCXX ...LONG
Bottom line for most job hunters is "what needs to be on my resume so the recruiter will forward it to company X" The simple answer is certs relevant to the position. Once at the interview, it is the job of the company at hand to screen the paper certs vs. the real McCoy vs. the up and coming. Most of these posts imply that paper certs include anyone without a CCIE or without extensive experience in [insert skill here] as a paper cert. The reason we have paper certs is because employers tolerate them. If you have hire/fire authority get rid of your dead weight and hire someone new. What have you got to lose??? Grab your n*ts (or female equiv), counsel/mentor/whatever your subordinates and put their future directly on their shoulders... I've seen plenty of paper certs myself but I am not in any position to do anything about it but I imagine some of you are. So when Monday roles around, some one on the list should get their local paper cert in their office and put him on notice. Let's let this thread die already... It's not as elitist as some of the previous ones but it heading in that direction... if you have any doubts, notice how the well respected members on this list are not contributing... as far as I'm concerned, that says it all. Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Password Utility
There's also one for the palm pilot, I'll look up the url if you're interested... Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > John Neiberger > Sent: Monday, March 19, 2001 5:53 PM > To: [EMAIL PROTECTED] > Cc: [EMAIL PROTECTED] > Subject: Re: Password Utility > > > http://www.alcrypto.co.uk/cisco/ > > >>> "The.Rock" <[EMAIL PROTECTED]> 3/19/01 9:39:18 AM >>> > Anyone have the password hash utility to de-crypt a password? > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: IOS version 13.xxx ?? and a Rant...
unless he's talking about some private area on CCO there is no 13 yet I'm still waiting on 12.1 to go GD! Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > John Neiberger > Sent: Monday, March 19, 2001 7:08 PM > To: [EMAIL PROTECTED] > Subject: Re: IOS version 13.xxx ?? and a Rant... > > > Wow, 13 already? That's pretty surprising since 12.1 isn't GD yet and > 12.2 isn't even out yet. > > >>> "Buri, Heather H" <[EMAIL PROTECTED]> 3/19/01 10:41:14 AM >>> > Hi Everyone. > > Well, I finished my BSCN course through Global Knowledge last week. I > have > to say I was kind of disappointed. I really was wanting to spend some > good > time on BGP and OSPF but we had to rush through it because we wasted a > whole > day going over RIP??? I thought this was supposed to be an advanced > class! > My opinion is the only refresher we should have been given on RIP is: > > Router Rip > > Anyways, the instructor said they started making the labs easier > because too > many people complained about them being too difficult??? :::sigh::: > > Oh well. Thank God for this list and I guess I will be saving myself > $2000 > on the CIT course now. > > I will be taking my exam on April 5. I wanted to study BGP and Policy > Based > routing some more. > > My instructor did mention Cisco was up to IOS release 13 already. This > was > news to me. He said it had been out for some time. My question is, > has > anyone been using it yet? My instructor did say that they finally did > away > with my favorite command... write mem. A sad, sad day! Well, I knew > it was > coming. I don't suppose "c r s" will work at the command line?? :-) > > Heather Buri > CSC Technology Services - Houston > > Phone:(713)-961-8592 > Fax: (713)-961-8249 > Mobile: > Alpha Page: > > Mailing: 1360 Post Oak Blvd >Suite 500 >Houston, TX 77056 > > > > -Original Message- > From: Robert Padjen [mailto:[EMAIL PROTECTED]] > Sent: Monday, March 19, 2001 10:58 AM > To: Chris Haller; [EMAIL PROTECTED] > Cc: [EMAIL PROTECTED] > Subject: Re: Cisco Certs Becoming Paper CCXX > > > I respectfully disagree with your summary point. I > know at least three CCIEs (R/S) that can't network > their way out of a paper bag. The odds are good that > you'll find one that has the knowledge, but its not a > guarantee. BTW - I have a number of co-workers that > have failed the lab but can kick most butts out there! > > > --- Chris Haller <[EMAIL PROTECTED]> wrote: > > I too am pursuing CCIE certification and have > > noticed > > a recent influx in people attempting and passing > > CCNP > > and CCIE written, especially the recent addition of > > hundreds of people on this board ... > > > > Anyway, CCNA, CCNP, CCDP ... CCIE Written, this > > means > > nothing. It is good, takes a good amoumt of work > > and > > is somewhat difficult to achieve, but if that's your > > issue, only interview LAB CERTIFIED CCIE's. There > > is > > no such thing as a "Paper LAB CCIE" If you pass the > > lab, you know your stuff .. WELL. > > > > HTH > > > > > > > > > > > > --- Adele Galus <[EMAIL PROTECTED]> wrote: > > > Hi Mike; > > > > > > I find your comment very interesting, most > > positions > > > state how > > > many years of experience before applying. The only > > > exceptions > > > that I have seen with certification positions, is > > in > > > the programing field. > > > It's not the certification being a problem - it's > > > the resources for > > > people to obtain experience. > > > > > > My thoughts are that there needs to be more labs > > for > > > people to work in when > > > studying for their certification that are > > affordable > > > or that it can be obtain. > > > People need to be involved with study groups and > > > they should do volunteer > > > work or try working as a contractor. > > > > > > This problem became obvious when Cisco & Microsoft > > > started programs in > > > San Jose for the welfare people to start becoming > > > certified. Why did they do > > > that > > > > > > What amazes me is how these people, that you are > > > seeing, have passed the test > > > > > > my 03 cents worth. > > > > > > respectfully, > > > adele > > > > > > Mike Davis wrote: > > > > > > > I will probably get yelled at for this one > > but... > > > > > > > > I am a CCNA, CCDA, CCNP, and yes going after the > > > CCIE. > > > > So up front I am not against certs. > > > > > > > > I am becoming aware of more and more people > > > becoming > > > > Cisco certified and not know enough to go and > > > actually > > > > do the work. Our company has and is interviewing > > > for > > > > network folks, I have the opportunity to > > interview > > > > these people to verify technical experience. I > > > have > > > > had CCNA, CCNP, and yes even CCIE written folks > > > who > > > > could not tell me what they 'should'
RE: [RE: Password Utility]
http://www.atstake.com/research/tools/index.html about halfway down the page is the Cisco Type 7 Password auditor for the Palm, actually, there are quite a few "gee wiz" things for the palm there Tim > -Original Message- > From: Charles Nunie [mailto:[EMAIL PROTECTED]] > Sent: Wednesday, March 21, 2001 10:19 AM > To: Timothy Metz > Cc: [EMAIL PROTECTED] > Subject: Re: [RE: Password Utility] > > > Hi, > I am interested, pleasen give more info > > [EMAIL PROTECTED] (Timothy Metz) wrote: > There's also one for the palm pilot, I'll look up the url if you're > interested... > > Tim > > > -Original Message- > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > > John Neiberger > > Sent: Monday, March 19, 2001 5:53 PM > > To: [EMAIL PROTECTED] > > Cc: [EMAIL PROTECTED] > > Subject: Re: Password Utility > > > > > > http://www.alcrypto.co.uk/cisco/ > > > > >>> "The.Rock" <[EMAIL PROTECTED]> 3/19/01 9:39:18 AM >>> > > Anyone have the password hash utility to de-crypt a password? > > > > > > _ > > FAQ, list archives, and subscription info: > > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > > > > _ > > FAQ, list archives, and subscription info: > > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
MAC addresses - gets off topic
Anyone know if a mac address of 00:00:00:00:00:00 is illegal or reserved. I assume it is and here's the rest of the story... While I should have been studying for CIT I installed a beta of the next version of redhat linux. After I installed it I couldn't get on the net. I could ping other workstations (Win2K boxes) but I could not ping the router. Netmask was correct. after typing ifconfig to check the nic's setup I noticed that the mac was all nulls. Pretty strange, but the win2k boxes didn't seem to care, the 2500 did! All workstations are connected to a 2505 (25xx with integrated 8 port hub). I can understand that the router wouldn't return a ping, but does anyone know why the win2k did?? Is 00:00:00:00:00:00 even a valid address??? Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Access list help
_ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Access list help
yes, I see that my wildcard mask is all screwed up, I'm sending this from home and now I'm not sure if it's just a typo on my part or I actually typed it in like that on the router.... ;-( Tim "Timothy Metz" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Access list help
All, For some reason I am having problems with a seemingly simple access-list and any help is extremely appreciated. When I applied the list, It blocked www access (intranet www worked fine) to all except the BDC and the Exchange server. I assume I made a mistake with the wildcard mask. My stub of the intranet is 10.105.190.0 BDC is 10.105.190.10 Exchange server is 10.105.190.246 IP's authorized unrestricted access 10.105.190.8 thru 10.105.190.24 LAN is on e0, WAN on s0 Here are my guidelines in plain English permit all to local intranet permit our BDC to all permit Exchange server to all permit specific block of ip's to all (10.105.190.8 thru 10.105.190.24) deny all others to www permit ip all (for proprietary stuff some of our offices use and I don't currently have the time to see what ports they need) Here is the list I came up with: access-list 101 permit tcp any 10.0.0.0 0.255.255.255 eq www access-list 101 permit ip host 10.105.190.10 any access-list 101 permit ip host 10.105.190.246 any access-list 101 permit ip 10.105.190.8 0.0.0.16 any access-list 101 deny tcp 10.105.190.0 0.0.0.255 any eq www access-list 101 permit ip any any apply to interface e0: en, config t, int e0 ip access-group 101 out ctrl-z Thanks again, Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Stupid Cat 5xxx question
I've just read (and never noticed on the 5500 we have at work), that the 5xxx series has a RS-232 console connector (I assume this to mean DB9 or DB25) that requires the use of a rollover cable (it did not say null modem), so I guess that means I need two DB25/DB9 to RJ-45 connectors and a rollover between them to log on through the console port. Can someone please confirm. Happy Thanksgiving (to those who observe) Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Extended Ping and data pattern
Hmmm, never knew that... but I always use the extended ping to test our connectiveity through a VPN to company remote locations. 5 pings isn't enough to determine if the connection is reliable, at least 50 better yet 100 if you are separated by a large geographically distance (as we are). Tim > Guys, > > While studying the CIT. I read that using the extended ping you can change > the data pattern (0xABCD the default) to debug data sensitivity > problems on > CSU/DSUs or to detect cable-related problems such as crosstalk. > I don't understand that, did anybody tried it. > > Thanks a lot > > > > > > ___ > Tired of slow Internet? Get @Home Broadband Internet > http://www.home.com/xinbox/signup.html > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
fast track exams
any one tried out the CCNP exams at http://www.fasttrakexpress.com/cisco.htm ??? Comments??? Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
help with IP Helper Address
A couple years ago we (actually my predecessor) removed a server from a small remote stub network (172.26.91.X). All the printers were moved to a print server on the main network (172.26.90.X) and kept their assigned ip's in network 172.26.91.X. The two networks are connected via a 4000 series on the 90.X end and a 2500 series on the 91.X end. When a user in network 91.X tries to map a printer, none show up in the box (WinNT). I can't reasonably expect all of them to all remember the UNC names for their printers. I started searching CCO for a solution and it seems to be "IP Helper Address" I have noticed that I don't have any set and always wondered what they were, well, now I know. The question is, on which router do I put the address of the print server?? Thanks Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Access-list Problem with UDP Port 53
Access-list Problem with UDP Port 53Could you clarify your network configuration? Is the 2600 at your location and connected to the client via the T-1 on serX? I just did some similar but even more restrictive acl's at my job. Tim ""Richie, Nathan"" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... I am having a problem with an access-list on a 2600 router. It used for the clients T1 connection. the access-list as follows: access-list 100 deny ip 10.0.0.0 0.255.255.255 any access-list 100 deny ip 172.16.128.0 0.0.15.255 any access-list 100 deny ip 192.168.0.0 0.0.255.255 any access-list 100 permit tcp any any established access-list 100 deny icmp any any timestamp-request access-list 100 permit icmp any any access-list 100 permit tcp any any eq www access-list 100 permit tcp any any eq smtp access-list 100 permit tcp any any eq pop3 access-list 100 permit udp any any eq domain access-list 100 deny udp any any log access-list 100 deny tcp any any log When this acl is applied inbound on the serial interface, all web browsing stops. Looking at the logs and acl counters, it shows that UDP port 53 is being denied via the "access-list 100 deny udp any any log" statement. >From my understanding, TCP port 53 is used between DNS servers and UDP port 53 is used for DNS queries between clients and DNS servers. The client is not hosting a DNS server, so they only need DNS queries and replies to pass. Upon changing "access-list 100 deny udp any any log" to "access-list 100 permit udp any any log", all web browsing is enabled. Could someone please shed some light on what I am missing here? Thanks in advance, Nathan Richie _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: help with IP Helper Address
Great, thanks! Tim ""Frank Wells"" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Put it on the router nearest the person who needs access to the remote > resources. > > > >From: "Timothy Metz" <[EMAIL PROTECTED]> > >Reply-To: "Timothy Metz" <[EMAIL PROTECTED]> > >To: [EMAIL PROTECTED] > >Subject: help with IP Helper Address > >Date: Tue, 28 Nov 2000 18:25:28 +0100 > > > >A couple years ago we (actually my predecessor) removed a server from a > >small remote stub network (172.26.91.X). All the printers were moved to a > >print server on the main network (172.26.90.X) and kept their assigned ip's > >in network 172.26.91.X. The two networks are connected via a 4000 series on > >the 90.X end and a 2500 series on the 91.X end. When a user in network 91.X > >tries to map a printer, none show up in the box (WinNT). I can't reasonably > >expect all of them to all remember the UNC names for their printers. I > >started searching CCO for a solution and it seems to be "IP Helper Address" > >I have noticed that I don't have any set and always wondered what they > >were, > >well, now I know. The question is, on which router do I put the address of > >the print server?? > > > >Thanks > > > >Tim > > > > > >_ > >FAQ, list archives, and subscription info: > >http://www.groupstudy.com/list/cisco.html > >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > Get more from the Web. FREE MSN Explorer download : http://explorer.msn.com > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Access-list Problem with UDP Port 53
Title: RE: Access-list Problem with UDP Port 53 Correct, when you make a tcp or udp request on a known port (dns, smtp, ftp, etc, check http://www.isi.edu/in-notes/iana/assignments/port-numbers for a list), the response from the destination is always (supposed to be always) returned on a port greater than 1023. This was the part that confused me, I couldn't figure out if you were trying to block your clients dns requests or block outside sources from making dns requests to your dns server. Keeping tweaking it and if you need any help just ask. -Original Message-From: Richie, Nathan [mailto:[EMAIL PROTECTED]]Sent: Wednesday, November 29, 2000 2:59 PMTo: '[EMAIL PROTECTED]'Subject: RE: Access-list Problem with UDP Port 53 Basically, I am trying to protect the clients network from the Internet. The serial interface is the gateway to their ISP. I fully understand the purpose of access lists, but I am still becoming familiar with the proper configuration for different scenarios to provide the desired results. I recieved an explanation from another gentleman in our study group. He states that when you receive a DNS querie reply, it uses a UDP greater than 1023. So in order to get DNS reponses, I need to open up UDP port >1023. I will do this using the ISP's DNS servers as the source IP. Hope I made sense here. Thanks for your offer to help.
CCNP Library at Bookpool
FYI: Bookpool.com has the CCNP library in stock for $134.95 Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: DRAM and Boot ROM's
from what I've read, the simms must have parity and someone said that Cisco gear doesn't like double sided simms. I am about to buy some memory for a 2501 and 2505 and would love to hear what you learn. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Ole Drews Jensen > Sent: Wednesday, November 29, 2000 8:03 PM > To: '[EMAIL PROTECTED]' > Subject: DRAM and Boot ROM's > > > There's a 4MB DRAM SIMM on my 2501. > > In a previous e-mail (8/27 by John Hardman) I read that almost any 72 pin > SIMM's would work as DRAM SIMM's, but no matter which of the > about 10 I have > lying around works correctly; They all say 1024 Kbytes of main > memory when I > boot up, even though they vary from 8 to 16 MB. > > I have been searching for information about this on the Cisco site, but > can't really get the facts that I am looking for. > > FYI, my Boot ROM's are: > > MX B9536 > 08-0034-01 > FW1 10.2(5) > 28058A > > MX B9536 > 08-0035-01 > FW2 10.2(5) > 28057A > > Would I need to upgrade them before the SIMM's would work? > > Also, if anyone know of a place where DRAM and Flash SIMM's can > be purchased > for a good price, please let me know. > > Thanks for any comments on this, > > Ole > > > Ole Drews Jensen > Systems Network Manager > CCNA, MCSE, MCP+I > RWR Enterprises, Inc. > [EMAIL PROTECTED] > http://www.oledrews.com/ccnp > > NEED A JOB ??? > http://www.oledrews.com/job > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: CCNP Library at Bookpool
Damn, I forgot all about them in my 2 week quest for the set ;-( Tim "Ross Bernardo" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Is this the 4 book bundle? If so Books-a-Million has it for $120.00. > > Ross > > -----Original Message- > From: Timothy Metz [mailto:[EMAIL PROTECTED]] > Sent: Wednesday, November 29, 2000 12:04 PM > To: [EMAIL PROTECTED] > Subject: CCNP Library at Bookpool > > > FYI: > > Bookpool.com has the CCNP library in stock for $134.95 > > Tim > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: RJ45 to AUI
get a transceiver... we have a bunch of aui to fiber transceivers, they come in all flavors Tim ""Circusnuts"" <[EMAIL PROTECTED]> wrote in message 007501c06d89$497dc420$[EMAIL PROTECTED]">news:007501c06d89$497dc420$[EMAIL PROTECTED]... > Any cabling ideas. I need an RJ45 connection to DB15, for a remote = > transceiver... > > Much appreciated !!! > > Merry Christmas !!! > Phil > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: is this statement true ??
I think I saw that on the boson switching tests I've never heard that full duplex extends range... did they offer the usual cco url as a reference? Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Li Song > Sent: Monday, December 25, 2000 10:33 AM > To: [EMAIL PROTECTED] > Subject: is this statement true ?? > > > "full-duplex can be used over longer distance than > half-duplex" ?? > what 's your opinion ?? > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
IGRP Propagation???
Here's a strange one... maybe someone can shed some light... My home setup: Access Layer: 2505 Distro Layer: 2501 Core Layer: Netgear RT314 (DSL Router) Workstations on 8 port hub (built into the 2505) Access to Distro: Frame Relay Distro to Core (LAN side): Ethernet Core to Cloud (WAN side): Seimans DSL Modem I don't know alot about the telecom side of DSL but my ISP knows who I am based on my login, I do not get authenticated when checking mail or news. If I enable IGRP on the Cisco routers (The netgear is RIP only) then I get a message saying that I am not authorized to access the mail or news server on the ISP side. When I disable IGRP all is fine. Any thoughts? Thanks, Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Flash Memory Upgrade
Does anyone know if the 2600s (not 265X) and 2500s use the same types of Flash SIMMs? Thanks Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Access-list block sizes
powers of 2 "Andy Barkl" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > What are the "valid" access-list block sizes? > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: 2500 power supply
I've used my two 2500s in both the US and Europe. The voltage range is printed on the back and it hasn't been a problem. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Albert Lu > Sent: Sunday, December 31, 2000 9:51 AM > To: [EMAIL PROTECTED] > Subject: 2500 power supply > > > Hi all, > > I'm about to purchase some 2500s from the US, to use in Australia. Are > there any power conversion issues, as US uses a 120V, and we use 240V over > here. > > I've taken a look at Cisco's website, and the papers there say > that it will > auto-detect the voltage, or something like that. > > Just wondering if anyone has any experience in this matter, as I wouldn't > want to zap it when I plug it in =) > > Thanks > > Albert > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Help Required - Desperately
as a desperate measure, I would remove the ram and flash and then see if it boots... if it does, start adding things back in there is also a jumper to boot directly from rom/flash, see: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/cis2500/2500c fig/bootrom.htm apparently this has happened to other people: http://www.cisco.com/cgi-bin/Support/OpenForum/dispnewqa.pl/2190 Tim ""Mani .K"" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Hi all, > I am badly in need of help from you Cisco gurus. We have a 2522 Router > which was bought around 1996/1997. It doesnt boot now. The console > screenshot is shown below. > > > > System Bootstrap, Version 11.0(10c), SOFTWARE > Copyright (c) 1986-1996 by cisco Systems > 2500 processor with 8192 Kbytes of main memory > > Restricted Rights Legend > > Use, duplication, or disclosure by the Government is > subject to restrictions as set forth in subparagraph > (c) of the Commercial Computer Software - Restricted > Rights clause at FAR sec. 52.227-19 and subparagraph > (c) (1) (ii) of the Rights in Technical Data and Computer > Software clause at DFARS sec. 252.227-7013. > >cisco Systems, Inc. >170 West Tasman Drive >San Jose, California 95134-1706 > > > > Cisco Internetwork Operating System Software > IOS (tm) 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c), > RELEASE SOFTWARE (fc1) > Copyright (c) 1986-1996 by cisco Systems, Inc. > Compiled Fri 27-Dec-96 17:33 by loreilly > Image text-base: 0x0101, data-base: 0x1000 > > Local Timeout (control reg=0x118) Error, address: 0x2101884 at 0x1076504 > (PC) > --- > > I have tried to enter the ROM Monitor prompt and tried to set the config > register as to boot from ROM and enter setup mode. But Neither does it > enter the setup mode nor does it come up to the router promt. The above > screen repeats itself. > > Can anyone infer what is the problem with the router. Also please tell > me what I can do to get the router prompt. > > Thanks in advance. > S.Kalidasan > > > > http://mail.indiainfo.com > First you had 10MB of free mail space. > Now you can send mails in your own language !!! > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
OT: For Sale-2x8mb Flash for 2500 series
Details: http://www.groupstudy.com/arch_front/sell.html Thanks Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Syslog Problem
Hi All, Ever since I upgraded to 12.X I have been unable to get them logging again to the syslog daemon on my server. Other things are logging fine so I know theres no problem with it. It did work fine with 11.X, I've searched CCO and can't find anything I didn't already know. One router is a 2501, the other a 2505. Here's one of the config's, I'd appreciate any help you all could offer. Thanks Tim Building configuration... Current configuration : 2190 bytes ! ! Last configuration change at 18:15:32 CET Fri Jan 5 2001 ! version 12.1 service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone service password-encryption ! hostname Access2505 ! boot system flash logging buffered 1 debugging no logging console enable secret 5 enable password 7 xxx ! ! ! ! ! clock timezone CET 1 ip subnet-zero no ip finger ip name-server 212.185.252.73 ip name-server 194.25.2.129 ! ip multicast-routing frame-relay switching cns event-service server ! ! ! # irrevelent hub ether stuff removed ! ! interface Ethernet0 ip address 192.168.0.252 255.255.255.0 ip pim sparse-dense-mode ip multicast ttl-threshold 16 no ip route-cache no ip mroute-cache ! interface Serial0 bandwidth 4000 ip address 192.168.10.252 255.255.255.0 ip pim sparse-dense-mode ip multicast ttl-threshold 16 encapsulation frame-relay no ip route-cache no ip mroute-cache fair-queue clockrate 400 cdp enable frame-relay interface-dlci 192 frame-relay intf-type dce ! interface Serial1 no ip address no ip route-cache no ip mroute-cache shutdown ! router rip version 2 network 192.168.0.0 network 192.168.10.0 ! ip classless no ip http server ip pim rp-address 192.168.20.253 ip pim send-rp-announce Ethernet0 scope 16 ip pim send-rp-announce Serial0 scope 16 ip pim send-rp-discovery Serial0 scope 16 ! logging facility syslog logging 192.168.0.2 access-list 5 deny 192.168.0.3 access-list 5 permit any ! snmp-server community xx RO snmp-server community RW ! line con 0 exec-timeout 5 0 password 7 x logging synchronous login transport input none line aux 0 transport input all line vty 0 4 exec-timeout 5 0 password 7 xx logging synchronous login ! ntp clock-period 17179719 ntp server 192.43.244.18 end _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Syslog Problem
For archive purposes: There are known issues with syslog in IOS 12.1.5 Now only if CCO would get a better search engine ;-( Tim ""Timothy Metz"" <[EMAIL PROTECTED]> wrote in message 935462$jvh$[EMAIL PROTECTED]">news:935462$jvh$[EMAIL PROTECTED]... > Hi All, > > Ever since I upgraded to 12.X I have been unable to get them logging again > to the syslog daemon on my server. Other things are logging fine so I know > theres no problem with it. It did work fine with 11.X, I've searched CCO and > can't find anything I didn't already know. One router is a 2501, the other a > 2505. Here's one of the config's, I'd appreciate any help you all could > offer. > > Thanks > > Tim > > > Building configuration... > > Current configuration : 2190 bytes > ! > ! Last configuration change at 18:15:32 CET Fri Jan 5 2001 > ! > version 12.1 > service timestamps debug datetime msec localtime show-timezone > service timestamps log datetime msec localtime show-timezone > service password-encryption > ! > hostname Access2505 > ! > boot system flash > logging buffered 1 debugging > no logging console > enable secret 5 > enable password 7 xxx > ! > ! > ! > ! > ! > clock timezone CET 1 > ip subnet-zero > no ip finger > ip name-server 212.185.252.73 > ip name-server 194.25.2.129 > ! > ip multicast-routing > frame-relay switching > cns event-service server > ! > ! > ! > # irrevelent hub ether stuff removed > ! > ! > interface Ethernet0 > ip address 192.168.0.252 255.255.255.0 > ip pim sparse-dense-mode > ip multicast ttl-threshold 16 > no ip route-cache > no ip mroute-cache > ! > interface Serial0 > bandwidth 4000 > ip address 192.168.10.252 255.255.255.0 > ip pim sparse-dense-mode > ip multicast ttl-threshold 16 > encapsulation frame-relay > no ip route-cache > no ip mroute-cache > fair-queue > clockrate 400 > cdp enable > frame-relay interface-dlci 192 > frame-relay intf-type dce > ! > interface Serial1 > no ip address > no ip route-cache > no ip mroute-cache > shutdown > ! > router rip > version 2 > network 192.168.0.0 > network 192.168.10.0 > ! > ip classless > no ip http server > ip pim rp-address 192.168.20.253 > ip pim send-rp-announce Ethernet0 scope 16 > ip pim send-rp-announce Serial0 scope 16 > ip pim send-rp-discovery Serial0 scope 16 > ! > logging facility syslog > logging 192.168.0.2 > access-list 5 deny 192.168.0.3 > access-list 5 permit any > ! > snmp-server community xx RO > snmp-server community RW > ! > line con 0 > exec-timeout 5 0 > password 7 x > logging synchronous > login > transport input none > line aux 0 > transport input all > line vty 0 4 > exec-timeout 5 0 > password 7 xx > logging synchronous > login > ! > ntp clock-period 17179719 > ntp server 192.43.244.18 > end > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Boson and BSCN
Which Boson is recommended for BSCN? Thanks Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Scores on Boson's and Colts - BCMSN
I just took BCMSN last week and got a 912. Until the last couple days (before the test) I was only getting scores in the 80's on Boson #2. Although my real test was similar (in subject matter) to #2 it wasn't as similar as the Boson CCNA vs. Cisco CCNA. I was pleasantly surprised when I hit the finished button, well, actually, more like ecstatic. I thought the test was challenging but no walk in the park. I was sure I was in the low 800's. As always, read the questions very carefully ;-) Passing score for my test (64 questions) was 699. As for study materials, I used the Sybex and Cisco Press books. They are very similar except on two points: The Sybex goes way into detail on Multicasting, this level of detail WASN'T necessary for my test. The Cisco Press book spends alot of time on the Campus model and the different models of switches, this WAS necessary for my test. Hope that helps, Tim ""Jennifer Mellone"" <[EMAIL PROTECTED]> wrote in message 000e01c0791d$a287dfc0$965cfea9@mellonj">news:000e01c0791d$a287dfc0$965cfea9@mellonj... > For folks who did Boson and Colts and passed BCMSN: > > How well do the scores on the Boson's and Colts predict success on the real > BCMSN? > > For example, I took Boson BCMSN Test #2 quiz A, B, and C and got 77, 75, and > 69 (I don't like that trend!). > Then I took Colt "BCMSN post assessment" and got 48/63 (passing score > 47-ouch!). > > With scores like that, do you think I'd pass by a comfortable margin, or > maybe just barely pass, or maybe not pass at all? > > - Jennifer Mellone > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: cisco press error??
I remember reading the exact same thing I think you are right. Tim ""tim sullivan"" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > All, > I am studying for the BCMSN exam and have run across something in the > cisco press book. > page 230 > Creating a null domain > "configuring an interface for multilayer switching by assigning an > interface to a vtp domian prior to assiging the interface to a vtp > domain places the interface in the null domain." > > I believe the third "interface" should read as switch,but I am not > all that positive.Can anyone make sense of this?? > Thanks for the help. > Tim > > _ > Get your FREE download of MSN Explorer at http://explorer.msn.com > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Little ID card
Ya, that little ID card is crap, Cisco should be ashamed to be s outdone by Microsoft on this point Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Jason Roysdon > Sent: Saturday, January 13, 2001 9:03 AM > To: [EMAIL PROTECTED] > Subject: Re: Little ID card > > > Be careful when you get mailed your certification letter. When I > passed my > CCDA, I took the letter out, skimmed and promptly tossed it, took out the > cert, and tossed the envelope. While hanging the cert, I recalled that I > had gotten a CCNA card and wondered why I didn't get one for my CCDA. I > went and checked the envelope, and sure enough stuck in the bottom was the > card. > > I wish Cisco would make them look a bit more professional, instead of a > piece of laminated paper. Furthermore, it'd be nice if they listed all > current certs on the same card as Microsoft does (MCP, MCSE, MCT, MCSE+I, > etc.). A card listing CCNA, CCDA, CCNP, CCDP, CCNP: Security > would make me > happy. And no, I didn't get a card for my CCNP: Security Specialization, > but I did get a Certification paper. > > Maybe I should just make my own Cisco card with all the nifty letters and > logos that I have? Probably not ok with Cisco, plus a bit too much work, > hehee. > > -- > Jason Roysdon, CCNP/CCDP, MCSE, CNA, Network+, A+ > List email: [EMAIL PROTECTED] > Homepage: http://jason.artoo.net/ > Cisco resources: http://r2cisco.artoo.net/ > > > ""Taylor, Don"" <[EMAIL PROTECTED]> wrote in message > news:[EMAIL PROTECTED] > effectcorp > .com... > > Yep, ya sure do. I've got two new ones since getting my NP/DP certs. > > > > -Original Message- > > From: Steven Dangerfield [mailto:[EMAIL PROTECTED]] > > Sent: Friday, January 12, 2001 8:32 AM > > To: [EMAIL PROTECTED] > > Subject: OT: Little ID card > > > > > > Don't want to sound too fussy, but, > > > > Now a days when you get your cisco cert do you still get the credit card > > sized > > id card that says your name, cisco id, and the qualification you've got. > > These > > sort of things are handy at interview time ! anyone passed CCNP and got > one > > of > > these let me know ! > > > > Steve > > > > Steven Dangerfield, Network Engineer/Analyst > > B.Eng, CCNA, CCSA > > > > Email : [EMAIL PROTECTED] > > > > > > Totalise - the Users ISP > > - > > To become a member and a shareholder > > visit http://www.totalise.net > > > > --- > > "From Golfing Breaks to Carribean Cruises, Totalise shop has the holiday > for > > you" > > http://www.totaliseshop.co.uk > > > > _ > > FAQ, list archives, and subscription info: > > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Timed Access Lists
Has anyone ever used timed access lists? I'm wondering if I can specify multiple times and days and still process through the list or will I exit the list after a test condition is compared... This is getting hard to verbalize but I'll give it a shot... ie: I want to limit www browsing on one time schedule during the week and a different time schedule during the weekend. Setting up two time ranges is not a problem Now I need to write the access list deny tcp any any eq http time-range no-http-weekdays deny tcp any any eq http time-range no-http-weekends permit ip any any will this work or will http traffic exit the list after the first test condition? Thanks Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Timed Access Lists
yes, you are absolutely right, and that's what I did. No one else responded to my message but these timed access lists are the best thing since sliced bread I no longer need to be concerned with my daughter compromising Net Nanny (which she is quite good at) even with her quite liberal surfing privileges. Here's the config in case you or anyone else is interested: ip access-list extended Michelle_Limit permit ip host 192.168.0.1 any permit ip host 192.168.0.2 any permit ip host 192.168.0.3 any time-range fri-evening permit ip host 192.168.0.3 any time-range sat-evening permit ip host 192.168.0.3 any time-range sun-evening permit ip host 192.168.0.3 any time-range weekdays permit ip host 192.168.0.3 any time-range weekend time-range fri-evening periodic Friday 19:00 to 21:30 time-range sat-evening periodic Saturday 18:30 to 21:30 time-range sun-evening periodic Sunday 18:30 to 20:30 time-range weekdays periodic weekdays 7:30 to 8:00 periodic weekdays 15:00 to 17:30 periodic weekdays 19:00 to 20:30 time-range weekend periodic weekend 7:30 to 10:00 periodic weekend 12:30 to 17:00 Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Gareth Hinton > Sent: Sunday, January 21, 2001 8:19 PM > To: [EMAIL PROTECTED] > Subject: Re: Timed Access Lists > > > Timothy, > > Would it not be better to use permits first, so that it does process them > all. > Then use a deny if you want to log exceptions, or otherwise leave it off. > > Gareth > > > "Timothy Metz" <[EMAIL PROTECTED]> wrote in message > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > Has anyone ever used timed access lists? > > > > I'm wondering if I can specify multiple times and days and still process > > through the list or will I exit the list after a test condition is > > compared... This is getting hard to verbalize but I'll give it a shot... > > > > ie: > > > > I want to limit www browsing on one time schedule during the week and a > > different time schedule during the weekend. > > > > Setting up two time ranges is not a problem > > > > Now I need to write the access list > > > > deny tcp any any eq http time-range no-http-weekdays > > deny tcp any any eq http time-range no-http-weekends > > permit ip any any > > > > will this work or will http traffic exit the list after the first test > > condition? > > > > > > Thanks > > > > Tim > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: BCMSN - ATM?
I sat BCMSN the first week of Jan and had no ATM nor LANE... Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Bradley J. Wilson > Sent: Monday, January 22, 2001 4:17 PM > To: cisco > Subject: BCMSN - ATM? > > > Okay, what's the deal with ATM on the BCMSN? The .pdf file on the Cisco > website says that ATM and LANE *are* on the test, and yet neither > of the two > books I have (the McGraw Hill / Thomas M. Thomas book, and the Exam Cram > book) have any ATM in it. > > In the immortal words of Frank Reynolds..."Can somebody get this nailed > down, please??" > > (Hopefully someone who's *taken* the test? :-) > > Thanks, > > BJ > > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: EASY ?? FOR MOST OF YOU
It's B. I think we just had this discussion not too long ago, it was quite a long thread with a lot of discussion on slot time (or the Cisco equiv term). Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Alvarado Jesus > Sent: Monday, January 22, 2001 8:11 PM > To: '[EMAIL PROTECTED]' > Subject: EASY ?? FOR MOST OF YOU > > > The network span of a 100Base-T Network (205) meters is approx. 10 times > smaller than the network span of a 10Base-T network (2500) meters Because > > > A) , Higher speed data signals attenuate more quickly and so cannot be > transmitted that far > > > B) . Both Networks have minimum frame sizes of 64 bytes and the network > spans must be tied directly to the minimum frame transmission > time to avoid > collisions. > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: But isn't that the routers job???
That's all still accurate (the Cisco terms and the theory) and can be found in the latest edition of the BSCN course book. I just read it myself, and know I've read it somewhere else (either in a Lammle or different Cisco Press book) Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > [EMAIL PROTECTED] > Sent: Tuesday, January 23, 2001 11:32 AM > To: [EMAIL PROTECTED] > Subject: But isn't that the routers job??? > > > I'm sure that somebody else will give a much more complete > answer, but in a > nutshell... > Don't forget that there is more than one component to 'routing'. The > 'routing process' (I'm using Cisco terms out of my rather old CIT notes > here, which in my opinion are thoroughly confusing in this context) > identifies the best path to a destination. This is what OSPF, EIGRP, etc > etc do. The routing process builds the routing table. > The switching process (we're still talking about routers here) moves > traffic from an input interface to an output interface. It uses the > routing table to work out which interface is the output interface. > > It is the switching process (i.e. moving packets, based on information in > the routing table) that is offloaded to the SP. The RP still does the > routing process (i.e. working out where to move the packets - building the > routing table). > > JMcL > -- Forwarded by Jenny Mcleod/NSO/CSDA on 23/01/2001 > 09:17 pm --- > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: ccnp studies
I normally hate to "ditto" questions but it seems all anyone ever talks about is the CiscoPress books. Are there any worthwhile alternatives to the "bore you to death" series from CP? Tim "jennifer cribbs" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > I am getting ready to study for the ccdp without formal classroom study. > Could someone please let me know or offer suggestions as to the specific books > that I need to purchase for this.What I would actually like to know is the > names of the actual books that the formal classrooms use offered by the cisco > academy for the ccnp curriculum. Those are the ones I would like to purchase. > > > Any help in this would be much appreciated. > > [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CCNA Boson exam
Personally, I think the ambiguously worded questions in boson test 3 were more like the real test. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Pieter Jordaan > Sent: Tuesday, November 14, 2000 7:06 PM > To: '[EMAIL PROTECTED]' > Subject: CCNA Boson exam > > > Hi > > I am gearing up to take the CCNA Exam. I have been testing myself with the > boson 2 Exam. How good are these for assessment. I have only done > the first > two tests so far and got more that 90% on each my first try. can > I expect to > pass CCNA based on these results or are the Boson exams easier. > > any input appreciated > > Thanks > > > Pieter Jordaan > > -Original Message- > From: Vazquez, Gervasio [mailto:[EMAIL PROTECTED]] > Sent: Thursday, November 09, 2000 10:00 PM > To: '[EMAIL PROTECTED]' > Subject: > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Windows Media Player
Right out of wmp help file: Use ports Specify a particular port, which is useful if your network or firewall administrator has established a specific port that enables streaming media to pass. Unless otherwise instructed, Windows Media streams attempt to pass through firewalls on port 1755. Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Jeff Duchin > Sent: Thursday, November 16, 2000 7:12 PM > To: [EMAIL PROTECTED] > Subject: Windows Media Player > > > Does anybody know what ports to block for WMP... radio and music? > > Thanks, > Jeff > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Hardware troubleshooting
Hi all, I recently inherited a 2501 and a 2505. Unfortunately, neither has any DRAM nor Flash. Without taking a couple hundred dollar gamble and buying a set of memory, is there anything I can do to see if they are functional? Should I expected them to (rx)boot and complain through the console port that there is no DRAM nor Flash?? Thanks, Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
OT: Metro Washington DC Area
Sorry for the OT, please direct replies to myself and not the list. I am considering looking for work in the DC area and was wondering if anyone on the list lives/works in the DC metro area. Sheer number of opportunities seem second only to CA Thanks, Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: what is the purpose of FECN?
The "F" in FECN means forward, so I choose "a." The packet arrives at the dest, notifying the dest that it experienced congestion along the way, so that rules out "b." Which is actually the correct answer if the question were "What is the purpose of BECN" "c." is not a function of FECN nor BECN. Sure wish "the router" was defined ;-) but this does keep it realistic ;-) Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > cslx > Sent: Sunday, November 19, 2000 10:39 AM > To: [EMAIL PROTECTED] > Subject: what is the purpose of FECN? > > > what is the purpose of FECN? > a.To tell the router that a packet experienced congestion > b.To tell the router that packets it is sending to a remote site are > experiencing congestion > c.To tell the router that there is bandwidth available > > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Cisco CCNP Preparation Library, Second Edition (Cisco Career Certifications)
Has the Cisco CCNP Preparation Library, Second Edition (Cisco Career Certifications) been published or is it just out of stock everywhere Thanks Tim _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: !H
That sounds like a Boson question, as a matter of fact, I remember getting it wrong by saying destination network unreachable, and not destination host unreachable. I never did check to see what the Cisco answer was Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > Miller, Nathan (AZ15) > Sent: Monday, November 20, 2000 5:16 PM > To: Richard Bosire; Jason yee > Cc: John Huston; [EMAIL PROTECTED] > Subject: RE: !H > > > Does it meas that the destination NETWORK is unreachable or the > destination > HOST?? > > -Original Message- > From: Richard Bosire [mailto:[EMAIL PROTECTED]] > Sent: Monday, November 20, 2000 8:01 AM > To: Jason yee > Cc: John Huston; [EMAIL PROTECTED] > Subject: Re: !H > > > destination unreachable i.e not path to the destination network > > Jason yee wrote: > > > hi anyone knows what does the symbol !H means in > > traceroute results > > > > __ > > Do You Yahoo!? > > Yahoo! Calendar - Get organized for the holidays! > > http://calendar.yahoo.com/ > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > -- > ___ > «¤»¥«¤»§«¤»¥«¤»§«¤»¥«¤»§«¤»¥«¤»§«¤»¥«¤»§«¤»¥«¤ > > Richard Bosire > Network Engineer CCNA,CCSE > AfricaOnline (k) Ltd > tel +254-2-243775 fax +254-2-243762 > http://www.africaonline.co.ke > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: IOS DHCP options (2514 and picky CATV server)
are you sure they are not also checking your mac address. I think roadrunner or @home does Tim > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of > John S. > Sent: Sunday, April 01, 2001 12:36 PM > To: [EMAIL PROTECTED] > Subject: IOS DHCP options (2514 and picky CATV server) > > > Hello, > > I've hooked up my 2415 running 12.1(2)T to the CATV modem, but > I'm having a > DHCP problem. Basically, the CATV company provides registered host names > (format: ab9-a.catv.area1.catv.com) and the host name must be in the > DHCP request packet, or the CATV system drops the request. > > Sniffing my NT4 SP6a machine requesting an IP, I see the host > name in under > the DHCP Header in the format: > DHCP Host name = "ab9-a.tv.area1.center2.catv.com". > > Sniiffing my Cisco router, this entry is "". > > Don't suppose there is any way to force the inclusion of the host > name in a > DHCP request in IOS? > > FYI, I set the hostname combos below with no luck: > > 1) > hostname ab9-a > ip domain-name tv.area1.center2.catv.com > > 2) > hostname ab9-a.tv.area1.center2.catv.com > (This gets truncated though) > > Regards, > > --john _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: AppleTalk on Support exam [7:269]
Took CIT on Apr 3 2001 and only had one... thank goodness! Tim ""Priscilla Oppenheimer"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > For those of you who have taken the Support exam recently, did you get any > AppleTalk questions? > > The outline for the 640-506 Support exam still includes AppleTalk. > > http://www.cisco.com/warp/public/10/wwtraining/certprog/testing/current_exam s/640-506.html > > The outline for the exam is a mess, though, so I'm not sure if I should > believe it. The outline for the course does not include AppleTalk. > > http://www.cisco.com/pcgi-bin/front.x/wwtraining/CELC/index.cgi?action=Cours eDesc&COURSE_ID=1492 > > THANKS > > Priscilla > > > > Priscilla Oppenheimer > http://www.priscilla.com > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=730&t=269 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Show running-config all at once [7:54367]
depending on the device and how many slots are populated, show tech can be
quite overwhelming ;-)
-Original Message-
From: McIntosh, Leslie (US - Tulsa) [mailto:[EMAIL PROTECTED]]
Sent: Saturday, September 28, 2002 10:08 AM
To: Tim Metz; [EMAIL PROTECTED]
Subject: RE: Show running-config all at once [7:54367]
I just use show tech-support when I want my running-config without page
breaks. I need the Page breaks due to the nifty feature of HyperTerminal
with XP scambling the buffer once it gets full...
Les
-Original Message-
From: Tim Metz [mailto:[EMAIL PROTECTED]]
Sent: Fri 9/27/2002 4:12 PM
To: [EMAIL PROTECTED]
Cc:
Subject: Re: Show running-config all at once [7:54367]
so that's what that does, and that explains why cisco works is always using
it.
Tim
""John Neiberger"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Use "terminal length 0" from priveleged mode to turn off the more
> prompt.
>
> HTH,
> John
>
> >>> "Don Claybrook" 9/27/02 2:29:31 PM
> >>>
> Hello.
>
> A customer asked me if I knew of a way to show the running
> configuration all
> at once, not page-at-a-time ("-more-"). I have no idea, but any
> hints,
> clues, or outright answers would be appreciated.
>
> Thanks.
&i=54372&t=54367
--
FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
- This message (including any attachments) contains confidential information
intended for a specific individual and purpose, and is protected by law. -
If you are not the intended recipient, you should delete this message and
are hereby notified that any disclosure, copying, or distribution of this
message, or the taking of any action based on it, is strictly prohibited.
[GroupStudy.com removed an attachment of type application/ms-tnef which had
a name of winmail.dat]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=54424&t=54367
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
