I am confused why you are using dafault routes and BGP at the same time
in this setup and why you are using IGP with just 2 routers?
Coming back to your question:
When you advertise an IGP route in the BGP process with network statement,
the
ORIGIN attribute in the update messages is set to IGP
in the dial-peer?
PING
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=43902t=43902
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
First, the traceback -Traceback= 60EC68D4 60EDD6B8 60EC74E0 60EBD4CC
60E9FE34 60EADCE8
6043407C 60434068 can be decoded by symbol files by Cisco and that will pin
point what
the problem is.
When you say Flash you mean the external PCMCIA flash card, right?
It is used only during the boot
If this is an IOS switch:
If you are trying to filter an IP address. Use ACL number between 1-99.
e.g
access-list 1 deny host 172.16.1.1
access-list 1 permit any
PING
Christian Fredrickson wrote:
Running a Cisco switch 3548XL
Trying to block a specific IP address. The access-list looks like
What is Squid?
Also, provide the topology.
PING
a. ahmad wrote:
Dear Members,
We have 2620 router with Fastethenet port and a Serial Interface. We just
want that no user traffic should directly go to router and only the traffic
that is coming through Squid should reach the router. How can
It depends on what else is there being process-swicthed.
If no other QoS, traffic stc. Experiment with show processes cpu command.
Construct your performance matrix.
PING
Ole Drews Jensen wrote:
My first line of defence is a 3620, and I am using and ACL on the outside
interface for incoming
guys, quick question, how much would you expect to pay for the following
kit?
1) cisco 3512xl switch with 2 GBICs
2) 2x2513 16flash 16 Ram
3) 3x2501 8MB Flash 16 MB Ram
4) 1603 with 8MB flash 6MB Ram + 1 serial wic card
5) 2610 16MB Flash 48MB Ram+ 2 serial Wic Cards + 4 port serial NM-4A/S
6)
I want to setup ISDN testbed for lab practice.
I wonder what equipment I need?
I have 2 3640s in hand.
I have 4 NM-2V in hand
I have VIC-2FXS in hand
I want to order VIC-2BRI...
Analog
PhoneNM-2V/FXS[3640]NM-2V/VIC-2BRI-S/T-TE--NM-2V/VIC-2BRI-S/T-TE[3640]NM-2V/FXSAnalog
Phone
In
need is mentioned for this topology
where as
I found that it is required to make it work.
2. Caslow states that both spokes cannot reach each other, whereas I see
that
they can (page 113):
3640-1#ping 10.10.10.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.2, timeout
on the interface)
* Issue a no shut on all frame-relay interfaces on both ends of the PVC.
hth,
Sean
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
PING
Sent: Thursday, April 11, 2002 7:43 PM
To: [EMAIL PROTECTED]
Subject: Re: Frame-Relay Problem [7
If I have this simple net:
3660(FR Switch)---3640
I am using NM-4T on both routers.
Default (HDLC) encapsulation causes both router serial interfaces to
come up. I am trying inverse ARP from Caslow book but as
soon as I enable FR (or even PPP) encap, line goes down. 3660 is the
Yes. It works from 3660 to 3800. Doesn't work from
NM-4T to NM-4T.
/N
Chris Camplejohn wrote:
Did you put frame-relay intf-type on the frame-interface?
Chris
PING wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
If I have this simple net:
3660(F
The question is that Caslow says on page-110 that if FR switching is
on, just enabling the encapsulation will bring up the PVC by using
inverse arp. I don't see that happening.
/N
Engelhard M. Labiro wrote:
Ping,
Have you configure the following comands on FR switch ?
1. Global config mode
Hi,
Does anyone know if its possible to configure 2 aux ports on 2 diffrent
routers, connect them back to back for DDR routing? I have seen some
configuration for this, but I suspect that you need 2 modems and 2 phone
lines, can someone throw some light on this subject?
Any responses much
12:34pm Saturday
If you do not have two telephone lines a dial tone simulator is a
wonderful
thing.
It has helped me a lot in my CCIE lab prep.
Richard
//
Nomadic Ping wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
Hi,
Does anyone know if its possible to con
If I have a setup:
R1 (E3/3)-(E2/3) R2
I want to make R1 think that it has lost the carrier as if I were
pulling the cable
out at R1 and this message should come up:
1d02h: %AMDP2_FE-5-LOSTCARR: Ehernet3/3 cable/transceiver problem?
A line flap by doing shut/no shut at R1
-HOWTO
for details on this). and you can have what you need.
Of course, this most probably violates cable
standards/recommendations,
but this is what you want in the end - errors ;-)
Marko.
- Original Message -
From: PING
To: [EMAIL PROTECTED]
Date: Tue, 2 Apr 2002 15:41:23
Tracebacks are HEX dumps that, when decoded, tell the exact story of
which process or harwdare/software components and routine casued the
problem. Usually in case of exception or crash.
IOS Developers use so called symbol files: to decode these messages.
They build the symbol files when the IOS
The designated port is not just the root ports.
1. Each root port is a designated port
2. Each designated port is not necessarily the root port.
There are other ports as designated, on the other side of the root bridge
to forward BPDUs downstream.
Nadeem
==
Cisco Nuts wrote:
Hello,If
I have follwoing questions:
Q1: When all the ports are in BLOCKing mode at start on switch,
how the initial broadcasts are then forwarded in a network so that
switches can learn about each other via BPDUs?
Q2: When a switch breaks the collision domains, then what is the
point of using Fragment
I am not sure if I understood the question completely but
I think you are trying to distinguish the L3 switching and
Routing?
Routing and Switching are two different functions taking place
within router. Routing takes place before switching can occur.
So, router first has to determine where this
Many congrats!!!
Nadeem
=
George Zhang wrote:
All,
The title says it all. I took my first attempt at the CCIE lab test
yesterday (March 5) in Halifax and received the Congratulations on Passing
the CCIE Lab! this morning.
I was the only person taking the lab test in Halifax
Doesn't hurt. No one is telling the actual questions.
It is far less helpful than practice exams...
Tarek Sabry wrote:
I think we should not be talking about the contents of the exams or how
much
of this or that. Doesn't do anyone any good.
No offense please.
Tarek
-Original
Considering default payload of 20 bytes, VoIP over Ethernet, no compression:
Codec sample size of 10 Bytes and sample interval of 10 ms:
Voice Packet per second = 1/byte size/sample size*sample interval*1000
= 1/20/10 / 10*1000 = 50 PPS
Total Packet size = IP+UDP+RTP+Enet+Payload=20+8+12+18+20=
There are circumstances when WFQ and CBWFQ are used on high speed interfaces,
specially in diffserv QoS environment.
Nadeem
==
s vermill wrote:
All,
Would you be so kind as to share your thoughts/experience with WFQ on high
speed links? I know that Cisco generally considers it to be
Congrats!
Nadeem
--
Ishrat Nadeem Zahid
CCNP
Cisco Systems,Inc.
Chelmsford, MA 01824
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=35579t=35570
--
FAQ, list archives, and subscription info:
I used CCNP Virtual lab by Sybex and ended up shipping them 128 CLI bugs in
just Remote
Access and
Support part. At CCNA level, you don't need much so you are satisfied. Be
careful while
buying
a sim for CCNP or higher.
Nadeem
==
--
Ishrat Nadeem Zahid
CCNP
Cisco
AUX is to plug a console when console port is busy, i.e. for terminal server
or
to connect MODEM. TTY is for used to configure Telnet.
Nadeem
==
Rafay Aslam wrote:
Some one please tell me the technical difference B/W AUX and TTY
Thanks,
--
Ishrat Nadeem Zahid
This also happens if you have duplicate IP address
Nadeem
==
Hamid Ali Asgari wrote:
Hi group,
I have a router which is the main gateway of my network. All the
hosts on my network can successfully ping everywhere on the internet,
but the ROUTER itself has always a success rate at 50
What you are running on T1?
If you are running Frame Relay, use FRTS to configure the CIR.
Another way is to use rate-limit command on the interface.
Another way is to use class based queuing to allocate the bandwithd to
different class of services.
Nadeem
==
Fernando Shiran wrote:
Hello,
If you see, interface up/line protocol down, most common cause is
encapsulation mismatch or clocking problem.
With serial it is usually clocking and DCE/DTE issue.
You should duble check that and also the interface
statistics.
Nadeem
==
dr_sukhi wrote
Respected Seniors and Friends in the
That's the way to go!
Nadeem
==
Scott H. wrote:
Thanks for the support guys. If nothing else, it has must made me mad and
more determined. As soon as I can get some sleep, I'm going to double up
my
study efforts from before. At this point, just passing is not going to
satisfy
I cannot understand correctly but you can use route maps and set a particular
interface for partical traffic by using access lists.
Nadeem
=
Gil Shulman wrote:
Hi all,
Does any body know how can I divert all traffic transparently from an ATM
interface to an Ethernet interface in order
1. Voice is a low burst rate data in addition to other characteristics
required such
as
low latency, jitter etc.
2. If you really want to think in terms of layers, voice is not layer 4
stuff, it is an
application, just as video is. It might go down through presentation layer
for say
compression
As a new member I want to say Hi to all.
I am pretty sure, you have heard this question before:
I am looking to buy material for CCIE RS written and
lab, so please take few seconds to type your best
recommendation. .
Thanks,
--
Ishrat Nadeem Zahid
CCNP
Cisco Systems,Inc.
ip classless is used to tell the routing protocols which supports VLSM that
subnet should be sdvertised as part of the route. ip classfull on the other
hand
is used to restrict to use major class subnet mask.
Nadeem
==
Arnaldo Gomez wrote:
Can someone give a gerneral explanation on these
a default route is used as the out of last resorte. In case router receives
a packet and
it cannot figure out where to send it, it forwards to the default route.
Nadeem
==
Ryn wrote:
Hello folks,
I am tring to figure out what RIPs ip default-network command actually
does.
If you have
You can use RSVP on FR. I think RSVP code was in 12.1 first time
but you might wannat try. You can also use priority ququeing with
CBWQ and allocating a b/w of 300K for voice class.
Nadeem
==
[EMAIL PROTECTED] wrote:
Hi,
I want to configure for a FR PVC rtp which should have a
Did you try format disk0: command?
Nadeem
Scott Nawalaniec wrote:
Hi Rik, Anybody,
Regarding formatting the flash from rommon mode. I have looked on Cisco's
website for a couple of hours trying to find the commands to format flash
from rommon and haven't found any useful information. I
, simple!
Nadeem
==
Scott Nawalaniec wrote:
Nadeem,
Format is not a found command in ROMMON mode for a Cisco 2620 router. I
don't know if this will work for other routers. Thanx for the input.
Scott
-Original Message-
From: PING [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, February
Nadeem
==
Rafay Aslam wrote:
Guys
I am researching on Netflow i.e. how i can install / configure it. If some
one knows how it works and from where i can get really good information on
it Please let me know.
Thanks,
--
Ishrat Nadeem Zahid
CCNP
Cisco Systems,Inc.
I typed the link below but could not see it in the posted message:
If it still does not appear below, search for NetFlow on CCO.
http://www.cisco.com/warp/public/732/Tech/netflow/
Nadeem
==
Rafay Aslam wrote:
Guys
I am researching on Netflow i.e. how i can install / configure it. If some
Even if Enet is available, it is not recomenned on Enet.
Depends on the traffic you have on the trunk.
Colin wrote:
Hello
I have been doing some reading on VLANs and Trunking and have read
conflicting information. Can you use a 10Mbs Ethernet interface when
running ISL or 801.1q or does
You can enter a ? to see tha max supported lines.
e.g. line vty 0 ?
e,g, for telnet you could have line vty 0 4
Nadeem
==
A Mehr wrote:
Hi all
Is there a way I can create additional VTYs on my 2621 Cisco Router ?
someone told me that the Line Vty 0 n can be used for this purpose , It
Do erase flash or delete flash
Then squeez flash
Also check your config register if it is set to go
to ROMMON. Set it to 0x2102 to boot from flash
Save config before reload..
It will go to ROMMON if config reg is set or no
image is found on flash and it loads boot image.
Also make sure that
What my understanding is that CEF and Fast Switching happen inside
the router i.e. b/w input and output interface, once the exit interface
(route) has been determined. So, routing protocol does not have much
to do with it. However total speed is switching+convergence time based
on your routing
i need the cvioce copy.if anybody have.mail to me!!
thanks!!!
send to [EMAIL PROTECTED]
best wishes for you!!
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=30292t=30292
--
FAQ, list archives, and subscription info:
it is a data link issue...forget about the masking.
without ip or with ip configed ..if you have the correct cable for bach
to back connection.
i would only check the clock rate statement on the DCE side and make sure
that the cable is good.
do s sho contr serial X
and check if in fact you have
0.0.0.0...common
denominator i am using dotted notation
i found out that the MTU size for ospf for BAy is 1576 and cisco 1500 and
they must both match in order to form adjencencies between both.
I have set the mtu size on bay 1500.
still no adjencencies but they can ping each other..What am I
the best track to follow is pick a subject and read
http://www.cisco.com/warp/public/625/ccie/certifications/rsblueprint.html
...you might think you know some topics but you will be surprised ...i
speak for myself..example the datalink layer...oh my
this is what i used to study and pass the
i think i understand what you are saying.
at the fram relay switch
type fram intf type dte
you can config it dce, dte and something else which does not come to mind
use ?
Thomas wrote:
Hi All - I am setting up my 2501 router as a frame-relay switch. I
succeed
when setting both of its
make sure the ip helper is set up on both interfaves to each vlan.
also add ip helper to your wins serverif you have one
Infotech wrote:
Group Pls help me with this config:-
cat 4k switch---cat6509 vlan 1 Vlan2
NT PDC 1NT PDC 2
USERx
go here http://www.fatkid.com/html/frame_relay.html
Mark Rose wrote:
A while back there was a posting showing how to set up a frame relay switch
with 3 routers (with configs). I misplaced the copy I had. I couldn't find
it in the archives. Could someone help me out.
TIA
Mark
jonh:
cisco shiped it for free for me .
John Hardman wrote:
Humm... Interesting, Cisco is willing to give them away free, but they do
not ship for free. I wonder which is the better deal, your price for
something free or something for free.
HTH
--
John Hardman CCNP MCSE+I
he routers which would ping all the desired destinations
in your network. That way, rather than sit there and ping x, then ping y,
etc., you could just type in the alias, and away it would go.
So I'm trying to learn how to do this, and it's not going all that well.
I've looked over CCO, and hav
it is way to summarize..
that is what is being done by
router rip
network 192.168.1.0
redistribute static
!
ip route 192.168.1.0 255.255.255.0 loopback 0
Hunt Lee wrote:
I don't understand the following routing configs. I understand that
redistribute static means it will redistribute
maybe this would shed some light..
on a pc
command .com would bring the pc up to dos.equvalent to ROM
after dos is loades then you clould load win3.11 or windows 95===equivalent IOS
lanadm wrote:
Hi
I am a newbie in Cisco CCNA, I learn form the book that "flash memory"
holds the
use any old 72 pin memory u have lying araound ..if it is for your lab ..who cares
if its for your company get the cisco stuff..though i doubt there is any diffrence
Brad Ellis wrote:
Jeremiah,
The 25xx DRAM is standard 60ns 72pin w/ Parity. If you dont have smartnet
on the router and it
i agrre with you.it should say in ...
Alec Smiths wrote:
Router A
neighbor 2.2.2.2 distribute-list 1 out
access-list 1 deny 160.10.0.0 0.0.255.255
In this case router A wants to deny updates for
network 160.0.0.0 propagated from router b (2.2.2.2)
to router a . But why does it say
i think you are in the wrong newsgyoup..
Issaya Ernest wrote:
I've a notebook PC Compaq armada 1560. After
reformating and reintalling windows 95, my notebook
display has been reduced to half the screen size How
can I make the screen full as was before.
Any help will be appreciated.
I have tried what you have been trying below in code 11.2 ...
and if i do a frame relay map statement for that dlc1 and i reboot i does not do iverse
arp.
i had the spoke do inverse arp and then mapped to the dlci; and it shoes the static
maping and the dynamic mapping when i do a "sh fram pvc"
d:
i did not look ar the question properly
Pedro Quezada wrote:
c
KOLIY wrote:
A router is receiving update for 1 subnet from different routing protocol.
Th system administrator wishes to take advantage of a path via a route
with less administer distance.Should I use ?
Try this link http://www.cisco.com/warp/public/474/
Ivan.
On Tue, 3 Oct 2000, Schmidt, David wrote:
Hello all.
I have a 2610 router that I don't have the console password or the enable
password . Can't connect to the ethernet port because I don't know the IP
of the port. If any one
Hi,
Can I search back those archive message which posted before in the site?
I think it can help me from keeping ask same question.
Many Thanks
Ivan.
**NOTE: New CCNA/CCDA List has been formed. For more information go to
http://www.groupstudy.com/list/Associates.html
64 matches
Mail list logo