et to "USB" RS232, as directed.
The Elecraft K3 Utility tool has no difficulty in comms with the rig.
If anyone has done this, please email me off-list for any thoughts on the
issue.
Many thanks.
--
73,
KD7YZ Bob EM88LL
___
e problem was solved.
I have no concept of why the cat, or I, would plug the speaker (B port) to the
Line-out.
--
Best regards,
Bob KD7YZ EM88LL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: ht
feedback, I MUST have done something. But search
thru config and manual I can't figure it out.
Help please?
--
73,
KD7YZ Bob EM88LL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
DP at ten feet above ground.
Took about 70 seconds. And I know I was sending over the air as the watt-meter
was telling me so.
So that's weird!. why the program was designed to to both I dunno. But it
surely does.
I have Yoniq too.
many thanks for the reply and help.
--
Best regar
chose from but not a single Elecraft.
Anyone ever used a K3 with that program?
--
73,
KD7YZ Bob EM88LL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Ele
pushed on the K3.
--
Best regards,
Bob KD7YZ EM88LL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://ww
n teh front, but the S-Meter drops 5
S-Units.
Yeah, signal does go to thje SDR device, but at a huge loss to the regular
operations.
What am I not seeing here ?
--
73,
KD7YZ Bob EM88LL
__
Elecraft mailing list
Home: http://mailman.qt
connector that would fit either to adapt them to the
K3?
Or maybe a universal box that lets me plug all the mic's in and have a cable to
the K3
Also run an Icom IC-9700 FWIW.
thanks!
--
73,
KD7YZ Bob EM88LL
__
Elecraft mailing list
I "used" to see the Ref*Call pulsating. It's been 3 or 4
months since I looked, or had the rig.
Now I just see " Ref Cal" , in Config.
Did I forget to set something ?
Or is there a newer firmware in the K3 that alters how ref-cal works?
again, t
of my K3?
thanks
--
73,
KD7YZ Bob EM88LL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Thanks for the direct-email help
I found my Elecraft cable for RJ45 to RS232
the next issue was correct settings in the K3 the with baud rate on the COM1
port
all is well now.
--
Best regards,
Bob KD7YZ
__
Elecraft mailing list
ld be wonderful
--
Best regards,
Bob KD7YZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.
#x27;s to track.
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www
On 12/7/2020 05:07, Bob KD7YZ wrote:
> On 12/6/2020 21:58, Fred Jensen wrote:
>> SPKR+PH Off?
>
> that is correct.
> SPKR+PH reads "no"
>
> tnx reply
Though after I just checked the 'Config" and was pressing Menu again,
rather than the screen returni
On 12/6/2020 21:58, Fred Jensen wrote:
> SPKR+PH Off?
that is correct.
SPKR+PH reads "no"
tnx reply
>
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/ele
s have audio but not both of them?
thanks
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This
sly figured that the Antenna input was before all the filters
and such.
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elec
the mods for me. Now I want to do
it and I can't find them listed so I can't fill in the "Form"
Magic or Memorex?
(most of you are too young to remember the TV commercial)
--
73
Bob KD7YZ
AMSAT LM #901
__
Ele
7;s NOT thru the KIO3b RJ-45 .
That flimsy connector was SMA soldered and that level I can't do .. or
wouldn't try anyway. Skill level deteriorated for that small stuff.
Any help on the audio?
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecr
on MSK144 ??
Hoping Don, W3FPR, will have some time after hectic daily Dayton
HamFest schedule to answer too.
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Hel
On 3/27/2019 19:01, Bob McGraw K4TAX wrote:
> With the radio in Data A mode, tap MENU, scroll to MIC SEL
YES!!!
the definitive answer !!
Apparently, I had mistakenly changed that setting.
thank you very much for a succinct answer!
--
73
Bob KD7YZ
AMSAT LM #
rned about the ancillary issue of number of bars as I was
curious just what Config setting I changed to cause Line to go away
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elec
On 3/26/2019 23:02, Nr4c wrote:
> Tap the knob to switch between Speed and Mic Gain. I think VOX is a hold
> function.
tnx Bill.
Tapp or push, all I see are Mic/
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecraft mailing list
Home
press the Mic/Speed button I see VOX and
no way to tickle the 4 to 5 bars.
So, uh, what'd I do?
80
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailm
Wondering how to do this.
I see a cable on https://www.arraysolutions.com/k3alc
A K3 ALC cable ...
or any other ideas ?
I have a W6PQL 2m SSPA with an ALC input on the back
many thanks.
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecraft
On 2/5/2019 14:47, Bob KD7YZ wrote:
So I'd previously asked if anyone knows how to read the same data from
the SUB-rx as I can get from reading the MAIN Rx on my K3 .
No one was able to figure it out or had been able to accomplish that.
Sad.
Expensive addition I have which is nearly us
ess a
way outside of "Commander' to make WSJTX read the Sub Band, but cvan't
do that either .
Thus, my question to y'all
--
73
Bob KD7YZ
AMSAT LM #901
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/l
On 04-Oct-15 1611, Bob KD7YZ wrote:
> What can I check, here, to see why the antenna tuner no longer
> automatically switches when I change bands?
>
got the answer direct email ... seems due to the extreme rats-nest of
cable(s) to 3 XVxx transverters; EME sequencers, KAT500, PC cables
00 after checking.
Summary is no matter what band I select on the K3, the KAT500 doe not
follow.
What can I check, here, to see why the antenna tuner no longer
automatically switches when I change bands?
--
73,
Bob KD7YZ
www.qrz.com/db/kd7yz
AmSat LM#901
_
thanks all who wrote off-list.
thanks mainly to Elecraft for the memory-editor
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailt
I got the scan but it stopped at the bottom and never restarted.
Should it scan continually or just one time?
thanks.
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http
KD7YZ tapped out:
I see my email-er somehow sent and resent the reply. no idea why,
however, I apologize for the hassle.
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http
tar-AT-2K. Occasional, sometimes several in a row, when
the VSWR is 1.5:1 or less
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailma
;Bars" RF shows peaks at 50w despite what the RF-Power display claims as
I turn the RF-Knob.
The SWR indicator is one bar.
Receive is great
I don't see a related item in Config.
--
Bob KD7YZ
__
Elecraft mailing
On 5/26/2014 15:07, tnny...@yahoo.com wrote:
> 10% of Average, or Peak Envelope Power?
> Are you using a PEP Watt meter?
>
A coaxial-dynamics WM with a 2500 slug
--
Bob KD7YZ
AMSAT LM 0901
http://www.qrz.com/db/KD7YZ
www.denstarfa
tting SSB, the output is barely indicating 10%
of (A) a HARD whistle pr (B) CW
And I have mic at 60 and cmp at 40.
What is a "Great" desk mike for the K3? Anyway, I am tired of the boom
mic so wanted a desk mic and this may be a good reason.
thanks
--
Bob KD7YZ
AMSAT LM 0901
http:/
K3 KAT500 tunes all bands 160m to 10m, nicely.
--
Bob KD7YZ
AMSAT LM 0901
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/
27;d only used it a
few days when I once wanted to try receiving a VLF station form Sweden.
I guess Stereo wasn't needed. I wanted the high sampling rate of the
0404, at the time then.
--
Bob KD7YZ
AMSAT LM 0901
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
_
I will re-install the EMU0404 and see how to get the audio out.
thanks for the idea.
--
Bob KD7YZ
AMSAT LM 0901
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/ma
-Rx because I shut off the mast mounted Gaasfet and although
the sub-RX audio dropped way off, the JT65 program showed a steady,
unchanging noise level.
So how do I tell the K3 to put the audio from the Sub Rx and not the
main Rx?
--
Bob KD7YZ
AMSAT LM 0901
http://www.qrz.com/db/KD7YZ
-ohm line circa a hundred feet of it to balun, then about ten feet
RG213 to KAT500
--
Bob KD7YZ
AMSAT LM 0901
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elec
On 4/18/2014 07:42, Don Wilhelm wrote:
> Bob,
>
> DATA A, AFSK A, PSK D, and FSK D are data submodes.
I am in Data-A
--
Bob KD7YZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
H
ht suffice for my
RG213 coax?
--
Bob KD7YZ
AMSAT LM 0901
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mai
On 4/17/2014 22:53, Nr4c wrote:> Well it's out of league.
that's also how I feel. Waa over my head.
Are you sure the mode is either DATA A or FSK D?
Not sure where I find a Mode named "FSK D" on the K3.
--
Bob KD7YZ
AMSAT LM 0901
http://www.qrz.com/db/KD7YZ
.
the number of ALC bars is fairly constant through the bands, in Tx-Data
mode, when sending via the Soundcard.
--
Bob KD7YZ
AMSAT LM 0901
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailma
ever, this must be an elusive setting.
--
Bob KD7YZ
AMSAT LM 0901
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfa
"Fucbr" (whatever that is),
hi hi, sorry, I need a new keyboard as this one has rubbed off letter as
well as some keys, I now see, do not type if pressed to lightly.
Funcube-Dongle-Pro-Plus
--
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
my K3.
I thought I was perhaps "there" except that the signals appearing on a
waterfall display, of SDR-Radio program, were all but reduced to 0 they
were so very very weak.
Is there another adjustment, in the CONFIG, I need to make?
--
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
www.dens
ule. Flip K3 over. Take off rear-half of bottom cover.
mid-section and aft for the two.
Prior to that, when I tried to xmit in any mode on any band other than
my three transverters, I got Main Display, bottom, saying 0 W
it means the ten-watt-module is fried.
Or,, at least in my case, it did.
--
l and what mode
> were you using?
A paddle and in CW mode
--
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.
Just wanted to monitor/see the output of the XV50 and can't seem to do it.
--
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: htt
It's the correct sensor. The W2 reads the K3 output. But when it's
cabled to the Elecraft 6m Transverter, there is no power reading. I
sometimes see a few green LED's for 1.3 to 1.5 VSWR. Never a power reading.
--
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
www.den
e lit.
--
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This
On 1/17/2014 23:53, Dick Dievendorff wrote:
> My K3 back panel has two 1/4 inch key jacks, one for a paddle, one for a
> straight key. I plug a paddle into one, and the keying line from my computer
> into the other. I have a vibroplex bug and plan to put a 1/4 inch mono Y
> adapter plug into
Willis 'Cookie' said:
> The easy way is to hold the dash on the bug.
unless I am missing something in Setup, I do not see how to tell the K3
that I want manual dashes and string-dots. There is no setup for the
keyer. So obviously if I short out the dash side, of the Vibroplex
paddle, I get dashes
I have learned from Elecraft that this may be indicative of two blown
FET's in the 10w amp stage inside the K3.
gremlins abound. And all while I was away doing chores outside. Since I
had the dogs with me it must have been the inside cats!
--
Bob KD7YZ
http://www.qrz.com/db/
0 W".
Checking CONFIG: Tune PWR shows 30.
Adjusting the K3 front-panel knob "PWR" is what I'd expect, variable to
whatever I turn it to.
What the heck happened while I was away?
--
Bob KD7YZ
http://www.qrz.
ay to get key-down WITH a closed PTT so external 6m PA comes on?
--
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qt
s not in "VOX"
--
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailma
tronics SignaLink-USB for a year now, fwiw.
Was all functioning.
About two weeks ago the KAT500 cable to K3 chain was likely disconnected
as I was making major back-end cabling configs to the transverters. And
I remained off HF that long.
Help Please.
--
Bob KD7YZ
http://www.qrz.com/db/KD7
ver-tipped plug to give it a push back in.
thanks ..All connected now.
--
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.n
.
--
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list
CH simpler for me then.
>
--
73,
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
http://www.denstarfarm.us/LGD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto
W mode.
Fortunate for me I had the RF lone form the rig unscrewed form the line
which goes to the LNA.
--
Best regards,
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraf
ress XMIT anyway ... wouldn't be
nice to destroy an expensive LNA . especially in the middle of a
QSO with a severely weak station.
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http:/
thanks for the help to everyone who replied direct and List.
Have expected readings now.
--
Best regards,
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help
e real IF of my K3 when the K3-Util command FI; returns 6550?
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth
K3 Notch-Filter is not adjustable in some reasonable
>> amount.
>>
MY "reasonable amount", and I started the original Question, is circa
200Hz ... since that was the extra width I perceived I needed to wipe
out the "offending" traces from
JT65/JT9, depending on which CQ I am answering.
Some places, or a place, can't remember at the moment, have plethora
WSPR and PSK kinda in the middle. So I began using the Notch after
asking around for ideas.
--
Best regards,
Bob KD7YZ
ke a surgical removal of
CW/Narrow-PSK modes/ WSPR
was just wondering. My K3 does so many things, most of them I haven't
discovered. Found nil in the manual; had to ask here "just in case".
--
Best regards,
Bob KD7YZ
http://www.qrz.com/db/KD7YZ
0" of the WSJTx display.
So, is there a hidden setting where I can make the Notch bout 400?? It
"seems" to be effective to "300" .
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.
ng properly for my usage from 160m thru 70cm .
--
Best regards,
Bob KD7YZ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This
Howdy K3' people:
Is there a way that a Band's Split and VFO-B can be retained in K3
Memory between band switching?
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
BTW, that little XG3 has really been handy.
In this recent case, I have a nice LNA the splitter for the 2 meter
array. The other day I did a
I jut put the XG3 at the input of that, out there at the splitter, and
could see back here that I didn't wreck the low noise pre-amp.
Really cool . XG3's
On 7/21/2013, () sent :
> This sounds like a marginal USB to serial adapter power situation.
thanks info/help Dick. Quick Response!
Mainframe.
"seems" it was the 9v battery. I plugged into a 12v wall-charger, then
got the d/l to work.
however, I also had a confusing time with the pop-up which
to close this window
--
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www
rce to buy them.
--
Best regards,
Bob KD7YZWin7-64bit + K3
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted b
rm
KAT500 is annoying. On a weak-signal QSOit means the difference from
making the QSO or not decoding.
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.ht
ol did nothing for the transverters. Either it's not
designed to do that or I'm not designed t try the tool.
PB CTRL was Shift =01 now it's .05 on SSB/CW/Data
Anyway, Now I have lo-cut and hi-cut back in CW & SSB & Data
Thanks a bunch!
--
Be
"Shift" and the other one on "Width".
Holding either will only go to "Norm" or "I/I"I .
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http:/
owards moonset and an Elevation of about 28 degrees
and down.
--
Best regards,
Bob KD7YZWin7-64bit + K3
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
ed there and tried to set Spectravue for 8.215; 10.0; 28.0 and
still see nothing from 6m. I even tried to set it at 50.10, to no avail.
So how do yu set it up to watch lower end of 6m on the K3, without
using a transverter?
thanks
--
73
KD7YZ Bob
__
were a dozen
remains of virtual ports.
Anyway, running fine now; loaded latest beta firmware 141 I believe.
How much can the KAT500 stand in bypass? I am testing my 2 x 3cx800a7's .
Howver, I am keeping it to about 350 watts for the time being.
--
ded 'cept now the utility
does not find the KAT500 on the only three COM-Ports listed in device
manager (including hidden).
what do I try next?
thanks
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/m
n ten minutes. Have had it
up to an hour and the xv432 is still solid.
The watt meter tells me what the output it. The LED's, well, still goofy
and generally just eye-wash for accuracy measured over time.
73
--
73
KD7YZ Bob
__
El
, and despite
re-installing the com-port, there are no errors from K3, just the
continual searching for any handshake on whichever port I'd used.
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listin
y, or even in the last hours actually. I was
probably pushing buttons, twisting knobs, in the excitement of working a
Sporadic-E opening on 6m
I done it, don't beat me. Mea Culpa
Now, what the heck is QRQ and why's that affect my filters?
--
Best
pushing upper-left knob makes the green LED go from Shift to"LO"
and the width LED to "HI"
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.n
y conclude that nothing is holding TX-INH active
until the DCW-2004 sequencer is itself keyed.
Therefore I have to ask anyone using TX-INH to guide me through this
confusing process.
Kinda specialized, however I hope somebody is using it like I wish to
do.
thanks in advance
--
73
On Friday Gregory used a Straight-Key to send:
-Original Comment---
> Have you got Menu Tech Mode ON?
yes.
--
Best regards,
Bob KD7YZWin7-64bit + K3
__
Elecraft mailing list
Home: http://mailman.qth.net/mail
don't bother to go back and re-do it
on any of the "Lists" I am on. I think Admin's set it that way to
reduce overall List-Traffic . I could argue either way on the topic.
--
Best regards,
Bob KD7YZWin7-64bit + K3
o OFF.
Not I am seeing 99.9dBV for an RMS reading of "1.09 A".
This isn't too helpful though. Perhaps David
can elaborate on how I get to a meaningful reading.
thanks for the help.
--
Best regards,
Bob KD7YZWin7-64bit + K3
___
And the reason I want to see this is because I just received my new XG3
Signal Source. In it they mention a way to see dBV on the K3 .
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
a think out there? Have I just put too many add-ons to the
K3 to make any of it work reliably?
Todays Critical Error messages twice with ERR DSE and once ERR TXG.
I did the Utility download and firmware update. I watched it go thru it.
No error me
On Sunday, Don () sent on an old
Straight Key:
> Bob,
> The suggested correction is to reload the DSP firmware (and DSP2 if
> applicable).
As I said, I did the 2 .. used cw on the transverter for a while. Back to
144 CW again and Just got the error message again.
--
73,
>> The suggested correction is to reload the DSP firmware (and DSP2 if
>> applicable).
> thank you Don.
seems to have worked by doing updates and so forth.
--
Best regards,
Bob KD7YZWin7-64bit + K3
__
Elecraft ma
Hi Don,
> The suggested correction is to reload the DSP firmware (and DSP2 if
> applicable).
thank you Don.
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.q
Howdy K3' people:
Was just siting here calling CQ (CW) on 144 with the transverter..
All of a sudden I wasn't calling CQ and the screen said :
E046068
ERR DSE or D5E, can't tell what the middle character is.
I had to power-reset to get back to calling CQ.
what's it mea
3/4 mile but not line-of sight through the hills.
--
73
KD7YZ Bob
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This lis
e.
as does the XV50 I own.
I just connected the 50-ohm Dummy Load and ran thru the three
transverters. Only the xv144 behaves oddly
--
Best regards,
Bob KD7YZWin7-64bit + K3
__
Elecraft mailing list
Home: http://mailman.qth
1 - 100 of 143 matches
Mail list logo