Hi
The real problem it seems to me, is one of philosophy rather than what
is practically possible.
The use of Ubuntu as a carrier vehicle has enabled a lot of people with
minimal Linux knowledge to use EMC.
As Kirk said, if a better technical solution were used at the expense of
usability,
On 24.11.11 19:21, Moses McKnight wrote:
Another option to consider is not using Unity or Gnome3 but maybe LXDE
or XFCE instead. Both of these are quite adequate for a machine control
and general desktop use. I used Xubuntu on my router table because it
took less resources, and it works
It seems to me that if you have an opinion on this matter, and you are
posting it to this thread, then you, personally, are not the type of
user we should be considering.
Is there anyone here with a strong opinion on specific Linux
distributions who has a plain, unmodified, LiveCD installation? I
Andy, you hit me severely there. My respect to all developers and
programmers of EMC, but I am sure there is a large silent majority of
EMC users who participate without writing to the list, just reading and
enjoying.
andy pugh schrieb:
It seems to me that if you have an opinion on this
is it not possible automate compilation processes?
--- On Fri, 11/25/11, Schooner schoone...@tiscali.co.uk wrote:
From: Schooner schoone...@tiscali.co.uk
Subject: Re: [Emc-users] Next distribution after Ubuntu 10.04 LTS is, no longer
supported?
To: emc-users@lists.sourceforge.net
Date: Friday,
I am using Debian squeeze + Trinity Desktop + Kernel and EMC2 from EMC
Repository. Basicly it's identical to Exe Linux Live-CD
http://exe-linux.fastfishwebsolutions.com/ with some tweaking (replace kernel
and some libs for emc). Basicly it's a good way to go for me, as I like
KDE3.5.
Nik
Am
2011/11/25 andy pugh bodge...@gmail.com:
The question to answer it not which distro _you_ prefer, but which
will be best for the project, and best for new users.
From my experience - those people, who are unfamiliar with EMC, are
unfamiliar with Linux. The fact that EMC is running on Ubuntu
On 25 November 2011 10:51, Peter Blodow p.blo...@dreki.de wrote:
Andy, you hit me severely there. My respect to all developers and
programmers of EMC, but I am sure there is a large silent majority of
EMC users who participate without writing to the list, just reading and
enjoying.
Indeed, my
Each night I backup my EMC machine home directory to a different computer
If I leave EMC running I get 'ERROR: Unexpected realtime delay'
The rsync cronjob causes this
I have varied time and disabled job so I am sure of this
I use 'rsync -vcupotrile ssh' and the files copied are
sending
On Thu, Nov 24, 2011 at 11:11:42AM -0800, Kirk Wallace wrote:
So, if I have a UP motherboard and upgrade to 10.04, which pulls SMP and
APIC. I might be able to fix my system by learning how to compile my
kernel and select UP instead of SMP?
You would have to build your own version of the
On Friday, November 25, 2011 11:17:21 AM kqt4a...@comcast.net did opine:
Each night I backup my EMC machine home directory to a different
computer If I leave EMC running I get 'ERROR: Unexpected realtime
delay'
I'll have to test this myself as I do a backup of:
FQDNdir level
From: andy pugh bodge...@gmail.com
To: emc-users@lists.sourceforge.net
Sent: Friday, November 25, 2011 4:20 AM
Subject: Re: [Emc-users] Next distribution after Ubuntu 10.04 LTS is no longer
supported?
It seems to me that if you have an opinion on this
On Friday, November 25, 2011 12:35:41 PM Edward Bernard did opine:
You were going to say? :)
From: andy pugh bodge...@gmail.com
To: emc-users@lists.sourceforge.net
Sent: Friday, November 25, 2011 4:20 AM
Subject: Re: [Emc-users] Next distribution after
Hello!
I am stuck with getting a servo motor moving again.
I got it working a month ago, then I had lots of other things to solve
and now that I have to assemble it all together to deliver the machine
to client, motor is not moving any more.
I tried to find the cause and what I have observed:
On 25 November 2011 17:56, Viesturs Lācis viesturs.la...@gmail.com wrote:
So it seems to me that the problem is in bldc component.
What might I be missing here?
It is hard to say without knowing what mode the bldc component is
operating in, and what hardware you are trying to drive.
--
atp
Sorry 'bout that. :
I am one of those new users and while I find all this discussion
interesting and informative I have been quite pleased with EMC2 up to
this point. While I'm eager to learn more about Linux I have neither the
knowledge or the time to do much tinkering with its innards so I'm
2011/11/25 andy pugh bodge...@gmail.com:
On 25 November 2011 17:56, Viesturs Lācis viesturs.la...@gmail.com wrote:
So it seems to me that the problem is in bldc component.
What might I be missing here?
It is hard to say without knowing what mode the bldc component is
operating in, and what
On 25 November 2011 18:21, andy pugh bodge...@gmail.com wrote:
What input do the Keling drives use?
Ah, sorry, Keling servos and 7i39. I need to read more carefully.
--
atp
The idea that there is no such thing as objective truth is, quite simply, wrong.
On 25 November 2011 18:11, Viesturs Lācis viesturs.la...@gmail.com wrote:
Not sure I understand about the operating mode. I suppose it has to do
something with this:
loadrt bldc cfg=qh,qh,qh
Oh, I did change the h mode recently, though that was intended to make
the parport work properly
Also remember that bit about either tying the fault input to the correct state
or changing its polarity in the HAL file so its default state is inactive
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
()_() signature to help him gain world domination.
2011/11/25 andy pugh bodge...@gmail.com: On 25 November 2011 18:11,
Viesturs Lācis viesturs.la...@gmail.com wrote: Not sure I
understand about the operating mode. I suppose it has to do
something with this: loadrt bldc cfg=qh,qh,qh Oh, I did change the
h mode recently, though that was intended to
On Fri, 25 Nov 2011, Viesturs L?cis wrote:
Date: Fri, 25 Nov 2011 20:52:23 +0200
From: [UTF-8] Viesturs L?cis viesturs.la...@gmail.com
Reply-To: Enhanced Machine Controller (EMC)
emc-users@lists.sourceforge.net
To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net
Subject:
On Fri, Nov 25, 2011 at 7:51 AM, andy pugh bodge...@gmail.com wrote:
On 25 November 2011 10:51, Peter Blodow p.blo...@dreki.de wrote:
Andy, you hit me severely there. My respect to all developers and
programmers of EMC, but I am sure there is a large silent majority of
EMC users who
2011/11/25 Peter C. Wallace p...@mesanet.com:
On Fri, 25 Nov 2011, Viesturs L?cis wrote:
Date: Fri, 25 Nov 2011 20:52:23 +0200
From: [UTF-8] Viesturs L?cis viesturs.la...@gmail.com
Reply-To: Enhanced Machine Controller (EMC)
emc-users@lists.sourceforge.net
To: Enhanced Machine Controller
On Fri, 25 Nov 2011, Viesturs L?cis wrote:
Date: Fri, 25 Nov 2011 21:40:09 +0200
From: [UTF-8] Viesturs L?cis viesturs.la...@gmail.com
Reply-To: Enhanced Machine Controller (EMC)
emc-users@lists.sourceforge.net
To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net
Subject:
2011/11/25 Peter C. Wallace p...@mesanet.com:
On Fri, 25 Nov 2011, Viesturs L?cis wrote:
Date: Fri, 25 Nov 2011 21:40:09 +0200
From: [UTF-8] Viesturs L?cis viesturs.la...@gmail.com
Reply-To: Enhanced Machine Controller (EMC)
emc-users@lists.sourceforge.net
To: Enhanced Machine
On Fri, 25 Nov 2011, Viesturs L?cis wrote:
Date: Fri, 25 Nov 2011 21:49:23 +0200
From: [UTF-8] Viesturs L?cis viesturs.la...@gmail.com
Reply-To: Enhanced Machine Controller (EMC)
emc-users@lists.sourceforge.net
To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net
Subject:
On 11/25/2011 01:11 PM, Eric Keller wrote:
On Fri, Nov 25, 2011 at 7:51 AM, andy pughbodge...@gmail.com wrote:
On 25 November 2011 10:51, Peter Blodowp.blo...@dreki.de wrote:
Andy, you hit me severely there. My respect to all developers and
programmers of EMC, but I am sure there is a large
2011/11/25 Peter C. Wallace p...@mesanet.com:
Can you unplug any daughterboard connectors on the 7I43 and launch one of
EMCs sample configs just to see if this is software or hardware related?
It is pretty late, 21:56 for me now, I have to go, so I will try it
tomorrow and report results.
On Fri, Nov 25, 2011 at 2:57 PM, Moses McKnight mo...@texband.net wrote:
And of course Debian is what Ubuntu is based on but it tends to be
more stable. It has not historically had as good hardware and media
format support out of the box as Ubuntu partly due to a more strict
adherence to
Hi,
I wonder if it would be possible to extend EMC in a way that I could ad
a 3D digitiser as an input device and control the position of a 3aces
CNC mill live via that digitiser so that I could use the CNC mill just
like a digital pantograph milling machine.
The digitiser, a Immersion
Hello,
Is it possible to clear the live backplot at the start of part program from
the part program? I am using Axis.
Thanks,
Mike
--
All the data continuously generated in your IT infrastructure
contains a definitive
Viesturs Lācis wrote:
2011/11/25 andy pugh bodge...@gmail.com: On 25 November 2011 18:11,
Viesturs Lācis viesturs.la...@gmail.com wrote: Not sure I
understand about the operating mode. I suppose it has to do
something with this: loadrt bldc cfg=qh,qh,qh Oh, I did change the
h mode recently,
On 25 November 2011 21:55, andy pugh bodge...@gmail.com wrote:
However, I just tried the command and got X server insecure (must use
xauth-style authorization); command ignored so I am not sure if it
works or not (this was in a VM, so might well be non-typical)
OK, just tried it on a real
On 11/25/2011 02:38 PM, Eric Keller wrote:
On Fri, Nov 25, 2011 at 2:57 PM, Moses McKnightmo...@texband.net wrote:
And of course Debian is what Ubuntu is based on but it tends to be
more stable. It has not historically had as good hardware and media
format support out of the box as
OK, just tried it on a real machine, and it worked fine.
So, in the directory referenced by PROGRAM_PREFIX in your INI file,
(probably home/emc2/nc_files) create a text file containing the
following lines.
#!/bin/sh
axis-remote --clear
exit 0
Then save that file with the filename M101 (no
Andy thanks for the quick response. I tried this but it did not work on my
system. I am running Axis ver 2.3.5 could that have anything to do with it?
I did not get any faults, it just executed the code but did not clear.
I think that is the problem. I ran the lines individually from a
terminal
37 matches
Mail list logo
