i am confused about the difference between ospf LSA summarization and
route summarization, i know they are different and also have certain
relationship,the LSA summarization is automatic runned at ABR,and the
route summarization must be manually configured.
what's the relationship of LSA summariz
i want to run ospf on atm pvc circuit must i add command "ip ospf network
broadcast" to router's atm subinterface configuration? (atm subinterface is
configured as point
to point)
i know that if i haven't add this command,the atm subinterface network
type is point to point, if i add ,the network
Not sure, but my understanding is that the default priority is 100 and you
should not set it if you want a device to be 100. Try setting one to 105 and
leave the other alone.
To rule out other interfering devices, I would use the standby x
authentication command on all HSRP routers to make sure
HI all,
I have to routers connected on a token ring segment. Every 120seconds
exactly they lose the neighbourship. This is then established immediately
but keeps flapping. There have been no changes to the default EIGRP config
here in relation to timers.
Any idea's
Andrew Larkins
BCom, CCN
1. make sure the clocking problem. Comstream should provide the clock
2. make sure you are using the correct type of cable (DTE/DCE type) from
Cisco serial to Comstream port
3. try to loop back comstream (local Loop back), you should find Line
protocol (looped)
4. check your link quality, do a BER
Dear all,
May I ask how to see the access log on the access server AS2509. When I do
the sh log on it I only se the interface Async1 changed state to up and down
(as shown below), but I want to see who had accessed it from which phone
number it call from, which ID it use and etc.
I know this in
hi guys:
i have 4 bri port in my cisco 2620,how to config
the 2620 so that the cisco2620 can dial the isp,anyone have some example
thanks a lot
best regard
hi guys:
i have 4 bri port in my cisco 2620,how to config the 2620 so that the cisco2620 can
dial the isp,anyone have some example thanks a lot
best regard
-
»¶Ó¹âÁÙ http://www.cmmail.com
_
FAQ, list arch
Yakout A. Esmat
GDC Communications Ltd.
WAN Systems Engineer
MCSE,MCP,CCNA,CCIE Witten
[EMAIL PROTECTED]
64 25 224-4447
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAI
I am trying to set up a modem to dial into the AUX port of a Cisco2610
router for remote support. I am using HyperTerminal on the PC and I have
set up a reverse telnet session into the modem (3 Com U.S Robotics 56K fax
modem) connected to the AUX port. The modems seem to connect correctly b
Hi, everyone!
I have a question about the MAC layer address, and I use the Ethernet for
making an example.
We all know that the first 3 bytes of the 48-bit MAC address are indicate
the vendor. Among the 3 bytes, the first is important, because the first 2-
bit in this byte has special meanings
Hi,
I'm hearing positive vibes about a training course
run by Martin Shortland in the U.K for CCIE Lab prep.
A 12 day course running at around £3900 + VAT.
Has anyone got any comments or got a link for this
course ?
PS : Also heard negative comments about NETGUN.
Regards,
Phil.
___
hi all
thanks very much for giving me all required urls...
regds
>
> Study Cisco wrote:
>
> > Hi all,
> >
> > i am trying to find out free installable copy of
> > radius or tacacs , can any one help me about this
> >
> > thanks in adv...
> >
> > _
Andrew,
What IOS version are you running on ?
Do you have any other Routers on any other Token Ring
segments ?
I believe that major surgery was implemented in IOS
11.3 for EIGRP not sure how that would effect Token
Ring though.
Have you analysed the Token Ring Segment for errors
e.g beacon
Hi,
I was just wondering if anyone has a sample configuration of what they've
configured on a router...
I have a 2611 with serial and 2 eths and i wanted to connect and OOB modem
to it to dial up and test etc.
It will have to authenticate to a pop site so it needs that ability.
Could someone
Daniel Cotts wrote:
The trick is getting the
experience to reinforce the knowledge you gain through study. My first job
in IT included moving furniture, taking out the garbage, and shoveling snow.
After that I might be able to work on the computers. It's called paying your
dues.
And I'm saying:
Hi,
I have 2 Routers connected via 3 Fa/Eth segments.
The segs are configured in an HSRP arrangement.
I pinged 224.0.0.2 from one Router and got 3 replies
that I expected from the other router PLUS one that I
dont understand.
This phantom device that replied cannot be telneted
nor tracert' but
Dear friends,
Thanks for u reply mail
But the problem is they dont know both the
"Username and password". When i connect thro Hyperterminal , it is asking for
the username and i am not able to proceed further
Any hardware reset is possible so that the router
will be configured as a
It seems to be that the EIGRP packets are sent out, but then never
acknowledged. What concerns me is that in the TCP/IP bible for the ccie's,
there is a reference to the exact problem on pg 392. They say that the
packets are being filtered. I know that the otherside router has access
lists, attach
my thoughts on finding the device:
1 sh cdp neigh
2 sh arp - if mac entry is there, trace down device...
3 sniff.
-jm
"Phil Barker" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi,
>
> I have 2 Routers connected via 3 Fa/Eth segments.
> The segs are c
I have used this to establish a ppp connection.
interface Asyncxx
ip unnumbered Ethernet0/0
ip helper-address x.x.x.x - WINS, DHCP, DNS
no ip directed-broadcast
encapsulation ppp
ip tcp header-compression passive
no ip mroute-cache
autodetect encapsulation ppp
async mode interactive
peer
I would try setting the Aux port speed to 28800 instead of 115200. That's
all I can see.
Will
""Suzi Beavis"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I am trying to set up a modem to dial into the AUX port of a Cisco2610
> router for remote support. I
How similiar are the COLT's to the actual exams... specifically the BCMSN
exam?
Cheers.
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Dear All,
I'm trying to issue the command " IP WCCP ENABLE"
but not accepted by router.
It keeps on saying "Invaslid
"
The router IOS ver is 12.0(7)t and should support
WCCP
Any help please
Ref
-Original Message-
From: Andrew Larkins
Sent: 01 November 2000 12:57
To: 'Phil Barker'
Subject: RE: EIGRP Neighbour - keeps flapping
the one router uses 11.2-18 desktop plus. As for the other, it is owned by a
governemt organisation to which I have no access.
We have already mentioned
Hello!
Any one give me some suggestion that
which paper of CCNP should I exam first?
Afterwards, which paper is the second, third and fourth ?
THANKS!
Ken
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct
Hi ,
Scenario is 2 cat 5509's connected together with an STM-1. Both are in the
same VTP domain but will not speak to each other. Configs are pasted below.
I DO NOT want to have management traffic (vlan 1) traversing across this
link. This link is working just VTP is not traversing. First que
Jeff,
It is a Novell 5 Server. Think it may have
something to do with SLP protocol on this box using
the same multicast address 224.0.0.2
Regards,
Phil.
--- Jeff McCoy <[EMAIL PROTECTED]> wrote: >
my thoughts on finding the device:
> 1 sh cdp neigh
> 2 sh arp - if mac entry is there, t
"Wilson, Christian" wrote:
>
> I am studying for 2.0 to test on Friday. I was using the ACRC books and
> there was a lot of DDR and Bridging. When I bought some study tests off the
> internet for 2.0, I didn't notice any questions on ISDN, DDR, or Bridging.
> Can you tell me, is this stuff not
If the IOS support wccp then issue :
-global command
ip wccp web-cache (to enable http)
-interface command
ip wccp web-cache redirect out (to redirect http on
desired interface)
Bye..
> Dear All,
>
> I'm trying to issue the command " IP WCCP ENABLE" but
not accepted by router.
> It kee
"Eric Mwambaji" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> By default Cisco IOS 12.0 will enable RIP v2 when
> sending out and will receive any version.
>
> To specify a version:
>
> Config t
> router rip
> version 2 (or version 1)
>
> Eric M.
> CCNA
No
Title: CPQRG
Enjoy!
Denis
-Original Message-From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]Sent: Wednesday, November 01, 2000 8:18
AMTo: [EMAIL PROTECTED]Subject: Do you need quick info on
Cisco Products?
Title: Recent postings on listing all titles.
Ok here it is, right off of Cisco's site. Not that I agree that every title should be listed but
http://www.cisco.com/warp/public/10/wwtraining/certprog/testimony_NEW.pdf
Thanks,
Joey Fowler
This is awesome!
Rajeev KS here! I just had to tell you
about SendMoreInfo.com! You get paid to read email!
They send you information about things you are
interested in and they pay you to check it out!
Here's the link:
http://www.sendmoreinfo.com/id/1019293
I know you are going to love this w
Try changing
login
to
login local
brgds
Richard
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Will Klein
Sent: Wednesday, November 01, 2000 8:16 AM
To: [EMAIL PROTECTED]
Subject: Re: AUX port and Modem Problem
I would try setting the Aux port speed t
try ip wccp ?
is hould be something like
ip wccp web-cache
-Kirk
On Wed, 1 Nov 2000, Refaat M. Saadi wrote:
> Dear All,
>
> I'm trying to issue the command " IP WCCP ENABLE" but not accepted by router.
> It keeps on saying "Invaslid "
>
> The router IOS ver is 12.0(7)t and sh
Hi,
I faced one strang problem today:
I have two WAN links, and today one link is down due to
that I'm not able to browse, then i used route map on my etherport for
serial1 which is up, after that also I was not able to browse.
What could be the reason?
TIA
Gm
Javed,
Yes it can be done, but only if you have the right attitude. You must be
willing to put in the effort to learn actively. Read something every day,
try to get equipment and play with it, figure out why something works or
does not. Try to solve problems yourself, before you ask for adv
Tim,
Well said..
This kind of advice is probably worth more than $0.02. :-)
Nigel.
- Original Message -
From: Tim Harkin <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Cc: <[EMAIL PROTECTED]>
Sent: Wednesday, November 01, 2000 2:30 PM
Subject: Re: Need Advice
> Javed,
>
> Yes it
IS PPP Multilink is possible with serial wan
link using statis routes?
if yes then how?
TIA
To my knowledge, Netware 5 SLP Multicast uses a well-known address of
224.0.1.22, not 224.0.0.2...
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Phil Barker
Sent: Wednesday, November 01, 2000 8:39 AM
To: Jeff McCoy; [EMAIL PROTECTED]
Subject: Re: Ping
Title: Etherchannel with 2912XL
I just setup an etherchannel between two 2912XL's. I'm running IOS 11.2. I searched CCO and could only find information on setting this up on set based switches. Also the book I've been studying appears only to have the same info. I set it up using the visual s
I did a quick check on the IEEE site
http://standards.ieee.org/regauth/oui/oui.txt
according to the list, there are only a couple of registered OUI's that
begin with a "1". They are registered to AT&T Bell Labs ( 80-00-10 )and DEC
( AA-00-00 )and a couple of successors )
I presume these were fo
Hi everyone, I dropped off the list for a few weeks while I was
transitioning into my new job as a network engineer at Gtech. Gtech
installs lottery systems all around the world. If anyone else on the list
works at Gtech please drop me a message to say hi.
I'm glad to see the list is going stro
Does anyone know of a company that makes a back to back cable for the little
smart serial ports on a wic-2t or similar. Thanks if you can help
daveh
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondi
If you can't find a job right now, especially in DC, there's something wrong. Get
Thursday's edition of the Washington Post. They're everywhere. Take your Pick.
--
Get the Latest News at CNN Interactive: http://CNN.com
_
GO away. You have too much time on your hands. THIS email address should
be used for study purposes only. BAN THE IP ADDRESS ASSOCIATED!!!
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: 01 November 2000 15:10
To: [EMAIL PROTECTED]
Subject: Get Paid To
Hi,
I faced one strang problem today:
I have two WAN links, and today one link is down due to
that I'm not able to browse, then i used route map on my etherport for
serial1 which is up, after that also I was not able to browse.
What could be the reason?
TIA
Gm
Etherchannel with 2912XL""Fowler, Joey"" <[EMAIL PROTECTED]> wrote in
message E37739B46CE9D311A76700508B6CAF293CA9B9@CORN">news:E37739B46CE9D311A76700508B6CAF293CA9B9@CORN...
I just setup an etherchannel between two 2912XL's. I'm running IOS 11.2. I
searched CCO and could only find information o
Title: RE: Paying One's Dues (was: Re: Need Advice)
It seems if you work for most companies in IT / MIS you have to pay some dues. Even companies like FedEx., IP, Harrahs, or any other top IT companies your still end up paying some dues and proving yourself. I have worked for some of these and
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/15303/scg/appp.htm
-Original Message-From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]On Behalf Of net974 at
YahooSent: Wednesday, November 01, 2000 10:38 AMTo:
[EMAIL PROTECTED]Subject: PPP Multilink.
IS PPP
I want to allow a particular server to do DNS queries such that when they
type www.cisco.com or something like that, it will go to the specify DNS
server and find the ip address. I have an access list allowing port 53 for
tcp and udp and it doesn't work. Can anyone help. Thanks.
Hello group
Please can you help!
i wiwhs to take the above exam and wish to find some info on it..
the cisco site hasn`t got anything so if anyone knows where:-
1 I GET THE EXAM OBJECTIVES LIST
2 AN EXAM CRAM OR SOMETHING SIMILAR
many thanks
steve
_
Hi,
Does anyone know where I can get the pinouts for connecting 2 1005 routers
via serial v.35?
TIA
BH
_
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.
Share information about yourself, create your
_
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.
Share information about yourself, create your own public profile at
http://profiles.msn.com.
_
FAQ, list archives,
I think wccp requires ip plus...I may be wrong though.
On Wed, 1 Nov 2000, Refaat M. Saadi wrote:
> Dear All,
>
> I'm trying to issue the command " IP WCCP ENABLE" but not accepted by router.
> It keeps on saying "Invaslid "
>
> The router IOS ver is 12.0(7)t and should suppor
we need the output of
"show int tok 0"
and
check the "Keepalive" too
Sam Li
- Original Message -
From: Andrew Larkins <[EMAIL PROTECTED]>
To: Cisco Mail List <[EMAIL PROTECTED]>
Sent: Wednesday, November 01, 2000 4:18 PM
Subject: EIGRP Neighbour - keeps flapping
> HI all,
>
> I have to
Hi,
Is there any CCIE Study group in Massachusetts area...?.
Any information on this will be appreciated.
Regards,
Sukhdev.
_
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.
Share information ab
Why not visit Cisco site and have a look at the objectives. There is no
bridging, no DDR, no access lists etc. anymore on BSCN (Routing 2.0) exams.
Thanks.
'Sola
-Original Message-
From: Dan Henry [SMTP:[EMAIL PROTECTED]]
Sent: Wednesday, November 01, 2000 3
His BCRAN book is excellent
Regards
Jon Eggert Gudmundsson
MCSE,CCNA,CCDA,Switching 2.0,Remote access 2.0
Network Administrator
Icelandic Banks Data Center
-Original Message-
From: Robert O'Brien [mailto:[EMAIL PROTECTED]]
Sent: 26. október 2000 12:05
To: [EMAIL PROTECTED]
Subject: Re: C
There will be soon...stay tuned.
- Original Message -
From: suk Ciscostudy
To: [EMAIL PROTECTED]
Sent: Wednesday, November 01, 2000 11:22 AM
Subject: Study Group in MA
Hi,
Is there any CCIE Study group in Massachusetts area...?.
Any information on this will be appreciated.
Regards,
I just brought the Boson tests for the BSCN and took the first test. I did
well considering I still have a bunch of BGP studying to do. The test
seemed kinda easy(or I'm just smarter than I thawt :-O). My question is to
those who have used these tests and taken the BSCN. Are the questions
gene
I'd be interested in this also
""Bradley J. Wilson"" <[EMAIL PROTECTED]> wrote in message
021101c04423$82625380$ec659aaa@bwilson">news:021101c04423$82625380$ec659aaa@bwilson...
> There will be soon...stay tuned.
>
>
> - Original Message -
> From: suk Ciscostudy
> To: [EMAIL PROTECTED]
>
Hi Group,
Anybody heard about Endless BGP Convergence Problem in Cisco IOS
Software Releases. I am multihomed to two ISP. My two routers speak to each other
with
iBGP. And one of my routeur, that is version Version 12.1(1)E3, EARLY DEPLOYMENT
RELEASE SOFTWARE, kept receiving BGP UPDATE from i
If a standby IP is set, could this be the virtual IPs response to the ping
of the multicast address?
Phil Barker <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi,
>
> I have 2 Routers connected via 3 Fa/Eth segments.
> The segs are configured in an HSRP arra
I find when I ask a question that may seem dumb to myself or to others, I
don't sign my name with my titles. Do you guys always sign with your titles
or just when you're answering a question?
Keith Townsend (MCSE, CNE, CCNA)?
_
FAQ, list archives, and subscripti
yes
inter s 0
ppp multilink
Sam Li
- Original Message -
From:
net974 at Yahoo
To: [EMAIL PROTECTED]
Sent: Wednesday, November 01, 2000
11:37 PM
Subject: PPP Multilink.
IS PPP Multilink is possible with serial wan
link using statis routes?
if yes then
Hey Everyone,
At 6:00 today I am being thrown to the lions. Objective 1 of 5 was
fuffilled last week: the preliminary technical interview. Tonight I will be
pitted against 5 Senior Engineers of Cisco's Network Service Engineering
division. We'll see how much I really know.
Wish me luck.
Scot
You mentioned that you have an access-list allowing port 53 for tcp or udp but the
question is are you filtering the response that is coming back from the DNS server.
Do you have access-lists filtering traffic coming from that direction? It will be
responding to a dynamic port number (it's de
I know this is a long shot.
Is anyone interested in forming a study group in the Boulder area?
I might have access to some gear.
I need some additional motivation.
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report mis
Questions:
Are they full mesh?
if yes, it is possible
or
they are partial mesh, you need
ip ospf priority command
ip ospf network broadcast
Sam Li
- Original Message -
From:
Mike
Canfield
To: [EMAIL PROTECTED]
Sent: Wednesday, November 01, 2000
11:08 AM
Subject
Hi All :
I can't found cisco demo testing site ?
Many Thank !eric
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
hi Brian.
I have a quick question from what you mentioned
regarding multipoint subinterface that I have always
been wondering about.
You mentioned, "Point to multipoint" and it can
communicate with many routers within that same
subnet."
Let's say there is a router in a headquarter, and 2
routers i
i used boson #2 and 3, did 95% consistently on them and passed BSCN with
850.
-jm
""Keith Townsend"" <[EMAIL PROTECTED]> wrote in message
8tpht7$5oo$[EMAIL PROTECTED]">news:8tpht7$5oo$[EMAIL PROTECTED]...
> I just brought the Boson tests for the BSCN and took the first test. I
did
> well conside
How involve is the BGP in the CCIE Lab exam?
Is the OSPF and BGP the two most important thing to learn in that lab
exam (and also in the real world)?
And if so, then the BGP course must be one of the most important course
to take. Am I correct?
_
FAQ, list archi
What are you trying to achieve:
A) remote dial-in for Exec session only to this router (no ppp)
or
B) remote dial-in for PPP session which will allow Telnet, ping onto and
via the router in question ?
Once I know a) or b) I can advise why your config is wrong.
Regards,
Bill
"Suzi Beavis" <
"Aaron" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi, everyone!
>
> I have a question about the MAC layer address, and I use the Ethernet for
> making an example.
>
> We all know that the first 3 bytes of the 48-bit MAC address are indicate
> the vendor. A
John,
If you have two routers on one LAN and ping 224.0.0.2 then only the other
router should respond, you will not get a response from the 'virtual' HSRP
IP.
Regards,
Bill.
"John Guenther" <[EMAIL PROTECTED]> wrote in message
8tpjeq$e45$[EMAIL PROTECTED]">news:8tpjeq$e45$[EMAIL PROTECTED]..
Count me in.
Neil Schneider
""Bradley J. Wilson"" <[EMAIL PROTECTED]> wrote in message
021101c04423$82625380$ec659aaa@bwilson">news:021101c04423$82625380$ec659aaa@bwilson...
> There will be soon...stay tuned.
>
>
> - Original Message -
> From: suk Ciscostudy
> To: [EMAIL PROTECTED]
> Se
You can accomplish this by allowing traffic on ports greater than 1023. Do
this with the following statement(s).
permit tcp any any gt 1023
permit udp any any gt 1023
Or...
you could use reflexive access-lists.
For reflexive access-lists:
Put the following statement in an outbound access-list
At 10:51 AM 11/1/00, Keith Townsend wrote:
>I find when I ask a question that may seem dumb to myself or to others, I
>don't sign my name with my titles. Do you guys always sign with your titles
>or just when you're answering a question?
>
>Keith Townsend (MCSE, CNE, CCNA)?
I think you just cont
At 10:04 AM 11/1/00, Aaron wrote:
>Hi, everyone!
>
>I have a question about the MAC layer address, and I use the Ethernet for
>making an example.
>
>We all know that the first 3 bytes of the 48-bit MAC address are indicate
>the vendor. Among the 3 bytes, the first is important, because the first 2
I took BCMSN on Monday and found that the COLT test I had practiced with in
the morning was very similar in covered content to the actual test (as would
be expected), but most importantly it helped prepare me for the somewhat
confusing way this particular test asks its questions. The actual test w
Hi All !
My name is Bamba and I am interested in your Cisco Study Group. Who should I
contact .
Bamba Thiam
MCSE,CCNA
Technical Support Engineer
Client Web team
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report miscondu
At 12:41 PM 11/1/00, Jim Erickson wrote:
>"Aaron" <[EMAIL PROTECTED]> wrote in message
>[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > Hi, everyone!
> >
> > I have a question about the MAC layer address, and I use the Ethernet for
> > making an example.
> >
> > I have a question about the follow
Try www.coffer.com/mac_find/
Priscilla Oppenheimer wrote:
> The first three bytes are a vendor code. Here's a pretty good list of
> vendor codes:
>
> http://www.cavebear.com/CaveBear/Ethernet/vendor.html
>
> At 09:57 AM 10/27/00, ROUTHIER, YVES wrote:
> >does anyone know a place where I can find
""Wilson, Christian"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I am studying for 2.0 to test on Friday. I was using the ACRC books and
> there was a lot of DDR and Bridging. When I bought some study tests off
the
> internet for 2.0, I didn't notice any
"Priscilla Oppenheimer" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> At 12:41 PM 11/1/00, Jim Erickson wrote:
> >"Aaron" <[EMAIL PROTECTED]> wrote in message
> >[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > > Hi, everyone!
> > >
> > > I have a question abo
Want some advice? Pay your dues in a K-12 public sector job. Lots of
action in today's educational technology buzz-word world. Pay is generally
terrible, but the exposure can be significant.
A good resume stuffer.
Best, G.
_
FAQ, list archives, and subscript
Hi all
I have a lab with 4 1602 routers. I have 2 of them, RA&RB, ospf over nbma
frame-relay. When I do a show neighbor on RA, I see RB in the INIT/DRother
state. When I do a show ip ospf neighbor on RB, I get nothing. I have
debug ip ospf adj running on both, and I see the hello's exchanging
Okay, here's what I had in mind: I'll volunteer to open
up my apartment (which is very spacious) to a group of people who want to
get together once a week (or more?) to study for the CCNP/CCIE
certifications. I'm a CCNA/CCDA myself and hold other technical
certifications, and am studying now towa
Hi,
I just started studying for my BCRAN and came across Async character
stream calls. Can anyone point me to a URL on how async technology works
and how is it differnt from synchronous calls like ISDN initiated calls?
also, how an async initiated call flows and make a successful connection
at t
You seem to misunderstand that having experience in the skill you are
'selling' is part of a skill-set. Without some experience you do not have a
complete skill-set, just a portion of one. I think you will find most
employers are looking for a complete skill-set in the tasks they require
hel
There's a site http://www.cheaplab.com that offers access to a router lab
for study for $25.00(USD) for 5 hours. Lab has 8 routers, 2 switches, 2
token MAUs.
_
Get Your Private, Free E-mail from MSN Hotmail at http://www.hot
Hubert,
If you have Halabi's book plus the BGP on Cisco website, should be enough
with BGP.
OSPF, read the doc CD should help a lot, and of course, play with different
setup of OSPF on Frame Relay is something every CCIE candidate is doing.
Jack
""Hubert Pun"" <[EMAIL PROTECTED]> wrote in mess
Dear Selvan,
You can go to this link below, and make the step by step, in step 12 change too
the password for user configured in router, you
can see this username when to type command show
running-config or
show startup-config. If
you do not configured service password-enc
At 10:45 AM 11/1/00, Priscilla Oppenheimer wrote:
>>2. When a multicast packet shoud be sent to this address, the destination
>>address in the MAC packet header should be set to 0130.b6f7.3000?
>
>Yes, that is right. The least-significant bit is set to one. It is the
>first bit transmitted. Thi
Congratulation phil .. :)
Any small study advise you can give .. "other than not study .. 30 days :)
it is a hard one"
Is there Anyone how score 100% of the Written Test .. !!
Good Luck in the Lab ..
Mohammed Hakim, CCNA R/S
- Original Message -
From: Phillip Heller <[EMAIL PROTECT
Your configs would be a big help, but without them my best guess here is
that you were using inverse arp and you added an incorrect frame relay map
statement. Frame relay map statements disable inverse arp for the protocol
it was configured for. Any dynamic ip to dlci mappings you had with inver
no idea if it fits your situation but an interesting thing happened to me in
the lab a few days ago..
same problem - adjacency wouldn't form.
once debug ip ospf adjacency was turned on it told me that the MTU didn't
match.
I was going over a bridged emulated lan service (atm and etherne
1 - 100 of 148 matches
Mail list logo