Hi folks,
Does anybody have experience with using ISL en 802.1q within the same
switch. I have ISL trunk between my access and distribution layer. Now I
want to connect a firewall on my access switch with 802.1q trunking
protocol. Is it possible? if the answer is YES, should I change anything in
m
most newer cisco switches can use an ISL and a DOT1Q trunk actively
I believe I did that the other day with a 3550 and a 3524xl
Larry
[EMAIL PROTECTED] wrote:
>Hi folks,
>
>Does anybody have experience with using ISL en 802.1q within the same
>switch. I have ISL trunk between my access a
We did this in a large implementation of Catalyst switches using a
mixture of ISL and dot1q and works fine with no problems. We used ISL
between 6500s and 6500s, dot1q 3500s to 6500s and 3500s between 3500s. I
assume this should be the same for what you are implementing. Just
change the trunking pr
""Steve Dispensa"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> > I've been arguing with a collegue of mine which one would be tougher to
> > achieve. I told him that it would be much more harder to have a computer
> > science or a networking degree (you have to take the GRE and
Hi.. Group,
I know how to monitor a port of same switch using the following command.
Switch1(conf)#int fas0/5
Switch1(conf-if)#port monitor fas0/7
But how do I port monitor a port in another switch. i.e. switch3. FYI they
are in the same network
Thanks a lot
___
Hi all
I have set up a VPN between a Checkpoint FW1 (v4.1 sp3) and a Cisco 827.
The tunnel installs correctly and I can connect from the FW1 subnet to the
Cisco subnet but not the other way around.
When I try to connect from the Cisco subnet I can see the packets enter
the access list tha
Hi Deepak,
The answer to you question what I feel is as follows.
Its not that after full congestion only Frame-relay Switch starts setting
bit FECN or BECN.When ever the traffic rate exceeds the threshold value some
percentage of it Then the switch informs the sender/reciver that it should
decreas
Team,
I think is time to shift gears...but I will give my two cents...
The question isWhat do you want to do for the rest of your life..Do
you want to be the Boss or you want to be boss around...
IMO a PHD/MS is a LIFE TIME investment that any person will have for the
rest of his/her li
Team,
I think is time to shift gears...but I will give my two cents...
The question isWhat do you want to do for the rest of your life..Do
you want to be the Boss or you want to be boss around...
IMO a PHD/MS is a LIFE TIME investment that any person will have for the
rest of his/her li
Just wanted to give a general shout out to all, I'm new here, figured I'd
need some help with some study issues.
been a CCNA for about 2 1/2 years, looking to pass CCNP exams by August
2003, been working on switching as my first exam.
needed a place to vent, looking around here yesterday I cam a
That is a very interesting question for me; Yestarday I went for a lunch
with a friend that got his MS on Economy, and I asked him:
- What do you think it would be better? Either use my time and energy to
get certificate or go for a MS or MBA?
He said:
- Absolutely go to the Certification pro
Can someone reccomend a good back that deals with Call Manager setup and IP
Phones. I keep finding these VOIP books (Caputo, etc.), but all they talk
about is routers, FXS and FXO, H323, yadayadayada. I know all that. I know
about RSVP, RTP, QOS, signaling. I did the CCNP Voice thing a few years ag
Howard,
just my 2 pence
you know ...
funny you should say about BGP ... I was just thinking that the other day...
but I personally don`t agree with the new protocol theory...
I personally don't claim to be able to do thisI can barely plug in a
switch but
as far as I am aware the ISP
Dear All,
Can any one of you tell me the command required for
making a dialup user login automatically in cisco 2611
router for PPP conenction.
regards
R.N.R
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59524&t=59524
--
John,
try Cisco CallManager Fundamentals: A Cisco AVVID Solution
http://www.ciscopress.com/catalog/product.asp?product_id={3682EFD7-CBA6-
46F6-A5C8-7CC5F3D22F12}
AFAIK is one of the best ever written on the subject.
Ciao
___
Maurizio Moroni
Software/QA Engineer
Cisco Sy
Welcome to the world of IP Telephonythe following is a good start...
Cisco IP Telephony by ciscopress - David Lovell
Cisco IP Telephony Network Design Guide
http://www.cisco.com/univercd/cc/td/doc/product/voice/ip_tele/network/
Cisco IP Telephony Solution Guide
http://www.cisco.com/warp/public/
At 1:33 PM + 12/19/02, Juan Blanco wrote:
>Team,
>I think is time to shift gears...but I will give my two cents...
>The question isWhat do you want to do for the rest of your life..Do
>you want to be the Boss or you want to be boss around...
Actually, if you want to be a boss, an M
At 2:39 PM + 12/19/02, steve wrote:
>Howard,
>
>just my 2 pence
>
>you know ...
>
>funny you should say about BGP ... I was just thinking that the other day...
>
>but I personally don`t agree with the new protocol theory...
>I personally don't claim to be able to do thisI can barely plug in
I ordered that one this morning. I feel better that someone else has read it
and it is relevant to my needs. I think I'm keeping Amazon in business!
Molte grazie
John
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59531&t=59523
-
I have not met anyone who liked the new Cisco site. I have tons of
errors and problems, I don't know what language the site is done in but
it pretty bad. When you try to contact Cisco about it, and no one gets
back to you. And when they do contact me back, they don't know why the
error is occurring
you sourcing clock from one side of this or tried another cable?
Brian
- Original Message -
From: "Wei Zhu"
To:
Sent: Wednesday, December 18, 2002 6:11 PM
Subject: Re: 2514 serial port flipping between up and down, [7:59501]
> I also tried "debug serial interface", only see myseq
hello,
indeed a large problem
the need for a hierarchical routing protocol ,that is effectively flat...
i think that is impossible for the internet to ever really converge ...if it
did it would indicate a lack of growth or movement which would not be
good for my job prospects !
i think
Hi all,
Can anybody tell me when I add static route to my default network it shows
with Administrative distance of 1,whereas we know that static routes to our
own interface have AD. of zero.
Example
C 10.77.152.128/25 is directly connected, FastEthernet1/0
S* 0.0.0.0/0 [1/0] via 10.77.152.129
i
> I think I'm keeping Amazon in business!
Funny, I'm taking the opposite tack: I've pretty much stopped buying Cisco
Press books, and have just started printing out PDFs from CCO. Anytime I
want to learn something new, I start by doing a search for whatever it is,
followed by "configuration guide
Hi Juan Blanco,
I totally agree with all your views,Yes CCIE and PHD cant be compared.Doing
PHD is really great and requires hardwork and dedication but going for CCIE
also we have to be very much dedicated.It doesn't matter irrespective its
value in term of longivity is less but still same dedicat
all static routes have an AD of 1...whether it is using ur interface or not.
all directly connected interface have an AD of 0
- Original Message -
From: "Munit Singla"
To:
Sent: Thursday, December 19, 2002 4:44 PM
Subject: Strange problem of route table [7:59533]
> Hi all,
> Can anybody
Please send your configuration and debug o/p then only something could be
thought off.
Regards,
MunitBrian wrote:
>
> you sourcing clock from one side of this or tried another cable?
>
> Brian
>
> - Original Message -
> From: "Wei Zhu"
> To:
> Sent: Wednesday, December 18, 2002 6:1
Hi Tunde,
Thanx for reply but can u tell me that I know that this static route to my
own
interface should have AD of 0 or am i wrong.Its mentioned in all the books.
can u clarify it or give me some link where its mentioned as u have written.
Regards,
Munit Singla
Tunde Kalejaiye wrote:
> all stat
""steve"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> hello,
>
> indeed a large problem
>
> the need for a hierarchical routing protocol ,that is effectively flat...
not so far fetched. consider that the ideal would be that anyone could plug
in their device, be that rout
I hear ya'! One other word to mention: Gnutella. Not very safe, but much to
pick and choose from, if you're careful.
-Original Message-
From: B.J. Wilson [mailto:[EMAIL PROTECTED]]
Sent: Thursday, December 19, 2002 11:48 AM
To: [EMAIL PROTECTED]
Subject: Re: RE: Good book(s)... [7:59534]
DNS based routing versus IPADD routing... this is interesting.
"you are gonna have to give me some grace on this as it has been a while
.. but "
Since we know that currently DNS resolution is already employed globaly (to
make things easier for the world community) and that rides on top of
At 4:37 PM + 12/19/02, steve wrote:
>hello,
>
>indeed a large problem
>
>the need for a hierarchical routing protocol ,that is effectively flat...
>
>i think that is impossible for the internet to ever really converge ...if it
>did it would indicate a lack of growth or movement which w
DNS based routing versus IPADD routing... this is interesting.
"you are gonna have to give me some grace on this as it has been a while
.. but "
Since we know that currently DNS resolution is already employed globaly (to
make things easier for the world community) and that rides on top o
Brian Zeitz wrote:
>
> I have not met anyone who liked the new Cisco site. I have tons
> of
> errors and problems, I don't know what language the site is
> done in but
> it pretty bad. When you try to contact Cisco about it, and no
> one gets
> back to you. And when they do contact me back, they d
At 5:56 PM + 12/19/02, test test wrote:
>DNS based routing versus IPADD routing... this is interesting.
>
>"you are gonna have to give me some grace on this as it has been a while
>.. but "
>
>Since we know that currently DNS resolution is already employed globaly (to
>make things easie
The topology diagram given has at least 3 errors. I wasted a few hours
figuring this out.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59546&t=59230
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/ci
The topology diagram given has at least 3 errors. I wasted a few hours
figuring this out.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59547&t=59230
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/ci
what are u reffering out please be clear
McAllister Paul wrote:
> The topology diagram given has at least 3 errors. I wasted a few hours
> figuring this out.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59548&t=59230
--
FAQ,
I tried to do a password recovery on a 2600 router. I
typed a confreg 0x2132 instead of confreg 0x2142 and
reset the router. After the router reload, I only see
the weird character display on my terminal. How do I
fix ?
Thanks in advance.
__
Do you
Go to the rom monitor mode and change your configuration register value.
Press break key with in 60 seconds of router reboot,you will enter thier.
then enter---> confreg 0x2142
>sync
->i(to reload) or use reset
thats all
bye
Munit
"[EMAIL PROTECTED]" wrote:
> I
Try changing your terminal speed to 19200 baud. 0x2132 sets the console
baud rate to 19200.
Ted
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59550&t=59549
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/
wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> That is a very interesting question for me; Yestarday I went for a lunch
> with a friend that got his MS on Economy, and I asked him:
>
> - What do you think it would be better? Either use my time and energy to
> get certificate or
""J.D. Chaiken"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I would have to disagree with you on some of your points. More often
> than not predictions turn out to be wrong.
I believe this is incorrect, and I've actually talked about this with other
people on this board.
It
Hey what i supect is hyperterminal settings problem.Please do confirm
whether u have thse settings..
Bits per sec: 9600
Data bits : 8
Parity : none
Stop bits : 1
Flow control: none
moreover still then try changing properties vty type/or speed if u have
change
Ted great,
can u refer me doc for this settings and speed regarding this I couldn't find
Regards,
Munit.
Ted Marinich wrote:
> Try changing your terminal speed to 19200 baud. 0x2132 sets the console
> baud rate to 19200.
>
> Ted
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7
David,
Welcome - although, I'm pretty new here too, but just the same Welcome!
Switching exam is a good start. Take the Dial-up next. Save the tough ones
for last!
Ted
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59557&t=59521
---
This may be dumb question, but I have seen this happen when connecting a
high speed port to a low speed port. One side is default to 1544 and the
other cannot do better than 64K.
So, what are you connecting to, specifically - 2514 to 2522?
Again, I might not be in the loop, but thought I would p
I agree! I use C quite frequently, as a hobby and to do creative things at
work. I use Linux and FreeBSD to monitor our network infrastructure and the
C come in handy to adding to it or creating cool cgi scripting.
You will gain from the insight even if you never use it. JAVA was created
using
> all static routes have an AD of 1...whether it is using ur interface or
not.
> all directly connected interface have an AD of 0
> > Hi all,
> > Can anybody tell me when I add static route to my default network it
shows
> > with Administrative distance of 1,whereas we know that static routes to
>
Hi,
Static routes can either have the AD of 1 or 0 depending on the way you add
them to your router.
e.g lates RouterA interface FE0=192.168.0.1/27 and it is connected to
RouterB FE1=192.168.0.2/27 & FE3=10.1.0.1/24.
To define route to 10.1.0.1/24 on RouterA you have two methods.
1. RouterA# IP
Here's a doc that covers the config register by bit. Keep in mind that the
bits are numbered right to left starting with zero at the rightmost. Watch
the wrap.
http://cco-rtp-1.cisco.com/en/US/products/hw/routers/ps282/products_installa
tion_guide_chapter09186a008007dfd0.html
So 0x2132. The "3"
I recommend the tough exams first as u all you will have the concepts so go
gor routing
first.
Ted Marinich wrote:
> David,
>
> Welcome - although, I'm pretty new here too, but just the same Welcome!
>
> Switching exam is a good start. Take the Dial-up next. Save the tough
ones
> for last!
>
>
When & or why does one have to enter:
ip routing
or
ipx routing
command?
I noticed, that on some of my test routers, the "router ospf #"
command doesn't take, if "ip routing" command hasn't been entered in
first.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59564&t=59
Hi Godswill,
Thanx for reply.I agree with u,but Still the doubt persists if both the
commands
are used then both entries come to the route table.As per your and mine
theory
also only better administrative distance should come into the route table,but
here both are introduced into the route table ,a
""meidinger"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> When & or why does one have to enter:
> ip routing
on by default, at least in the more recent IOS images
>or
> ipx routing
> command?
any time you want to add IPX routing capability to a router that doesn't
al
Thanx Daniel
Regards,
Munit
Daniel Cotts wrote:
> Here's a doc that covers the config register by bit. Keep in mind that the
> bits are numbered right to left starting with zero at the rightmost. Watch
> the wrap.
>
>
http://cco-rtp-1.cisco.com/en/US/products/hw/routers/ps282/products_installa
>
Hi Chris,
Hi the why its showing in the rout table.I have already given my route
table.Please
refer it and do clear my confusion.
Regards,
Munit
chris kane wrote:
> > all static routes have an AD of 1...whether it is using ur interface or
> not.
> > all directly connected interface have an AD of
ip routing is by default enabled.need to enable ipx routing if we are using
ipx..thats
all.ospf only runs on ip so by default ip routing is enabled if u have
disabled it ,u
have to enable it thats all.
Bye
meidinger wrote:
> When & or why does one have to enter:
> ip routing
>or
> ipx routin
Hi,
Your problem is the line speed. Register value 0x2132 specifies the line
speed. Change it and you will sleep well tonight otherwise, declare no-sleep
on yourself...
Further reading :
http://www.cisco.com/en/US/products/hw/routers/ps233/products_tech_note09186
a00800a65a5.shtml
Regards.
Godsw
Odd - this link didn't work for me until I replaced the "cco-rtp-1" host
with plain ol' "www"...if anyone else had this problem, give it a shot.
>
http://cco-rtp-1.cisco.com/en/US/products/hw/routers/ps282/products_installa
tion_guide_chapter09186a008007dfd0.html
BJ
Message Posted at:
http://
Hi all,
is it required to issue 'mls rp vtp-domain [domain-name]'on the logical
interfaces of an integrated router (MSFC for 6509MLS)?
Regs.,
Prasad.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59572&t=59572
--
FAQ, list archive
Hi Munit,
Let assume you put both coomands say:
1. IP route 10.0.0.0 255.255.255.0 172.16.0.1
2. IP route 10.0.0.0 255.255.255.0 FE1
since the AD of 1 is 1 and that of 2 is 0, option 2 will be the prefered
route
for any routing activity to network 172.16.0.1. The route defined by option 1
will b
Greetings,
I have been given the opportunity to install/configure a new 506E pix
firewall
which our client had purchased from another supplier.
Configuring it to provide basic connectivity seemed somewhat linear (I will
not be using any IPsec features ;) ), the client had also purchased a 168
bit
I recently bought a couple of routers. I was told that both have 4MB of
DRAM. How can I find out?
Both use IOS (a 2511 and a 2522).
Thanks in advance.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59575&t=59575
--
FAQ, list arc
I recently bought a couple of routers. I was told that both have 4MB of
DRAM. How can I find out?
Both use IOS (a 2511 and a 2522).
Thanks in advance.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59576&t=59576
--
FAQ, list arc
show version
show flash [ detail ] [ chips ]
--
TANSTAAFL
"there ain't no such thing as a free lunch"
wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I recently bought a couple of routers. I was told that both have 4MB of
> DRAM. How can I find out?
> Both use IOS (a 2511 and
Sorry if this is a dumb question! ;-) I want to make sure this design will
work before implementing it.
The customer has been using 192.168.168.0/24 in one small flat LAN. He has
run out of these addresses and is being hit by performance issues related to
broadcasts.
He wants to implement subnets
What's more difficult?
a) Memorizing configuration scenerios and commands on a Cisco router
b) Understanding Calculus, Differential Equations, Numerical Analysis,
Chemistry, Physics and Electrical Engineering well enough to create a
"meaningful" experiment.
One of my friends is working on his ma
Priscilla,
I'm sure someone can verify this with a 2600 specifically. As far as DHCP
in general, yes. We just did this with a much larger 6509-based network.
No problems. The only difference, of course, is that the MSFC has virtual
router interfaces per VLAN - not subinterfaces on a router on
Depending on the version of PIX code the unit is running, you might not
have to do too much.
First, go to your PIX, and issue the 'Show Version' command. If you are
running 6.1 or higher (I believe), you can go into config mode and issue
the 'activation-key' command followed by the 4 sets of alph
no, only when you connect to external router with physical interface.
- Original Message -
From: "puro prasad"
To:
Sent: Thursday, December 19, 2002 6:43 PM
Subject: MLS related [7:59572]
> Hi all,
> is it required to issue 'mls rp vtp-domain [domain-name]'on the logical
> interfaces o
I tried to connect to 2501, even use DCE/DTE to interconnect serial0 and
serial1 on 2514, seems the signal cannot go to the line.
Thank you.
- Original Message -
From: "Ted Marinich"
To:
Sent: Thursday, December 19, 2002 5:28 PM
Subject: Re: 2514 serial port flipping between up and down
do a show hardware command or a show version
sjc5-row13-cs3#sh ver
System image file is "flash:c2500-i-l.112-5.P", booted via flash
cisco AS2511-RJ (68030) processor (revision I) with 2048K/2048K bytes of
memory.
8192K bytes of processor board System flash (Read ONLY)
Configuration register
No more drinks for you, pris
Design seems like it will work...till an intern puts up a nother dhcp
server on the same vlan and people get wrong address's
:-P
Priscilla Oppenheimer wrote:
>Sorry if this is a dumb question! ;-) I want to make sure this design will
>work before implementing it.
Maybe what I really need for Christmas is a new router. ;-) My routers are
too old to do this sort of stuff. It would be terrific if you could mock it
up.
I'm just not totally conviced the router will behave the way it obviously
should. Could be the egg nog though.
Thank-you. I am indebted to you
Dear Wei,
thanks for the reply. Anyway if the command is run on any of the interfaces,
should this affect in anyway. I just wanna check this cuz the 'sh mls rp'
command on my msfc is not listing the switches in the domain. Any inputs??
Regs.,
Prasad.
Message Posted at:
http://www.groupstudy.com/f
"activation-key" commands only works with version 6.2.x or higher
"Mark W. Odette II" wrote:Depending on the version of PIX code the unit is
running, you might not
have to do too much.
First, go to your PIX, and issue the 'Show Version' command. If you are
running 6.1 or higher (I believe), you
Dear All,
My network have collision is this good sign?? Please help!!!
FastEthernet0/48 is up, line protocol is up
Hardware is Fast Ethernet, address is 000a.f477.662c (bia 000a.f477.662c)
MTU 1500 bytes, BW 1 Kbit, DLY 1000 usec,
reliability 250/255, txload 5/255, rxload 9/255
Wei Zhu wrote:
>
> I tried to connect to 2501, even use DCE/DTE to interconnect
> serial0 and serial1 on 2514, seems the signal cannot go to the
> line.
Earlier you said the interface on the 2514 was "up/down" or cycling between
"up/up" and "up/down." That usually indicates a misconfiguration, no
Don't know the effect if you set the command on logical interface, maybe
system will ignore it, basically it is used by MLSP hello message. No clue
for why it doesn't show the MLS-SE.
- Original Message -
From: "puro prasad"
To:
Sent: Thursday, December 19, 2002 9:16 PM
Subject: Re: ML
The interface is set to half duplex. Collisions are a normal part of half
duplex Ethernet.
However, do you really need it to be confiugred as half duplex? What does it
connect to? If it connects to a single port like a router or switch port or
to a single workstation or server, then you can use fu
The configuration is pretty simple, one side only clock rate 100,
another side nothing, both serial ports are not shutdown. I tried debug, can
see myseq count is increasing but not the other two counters. Is there any
fuse or something like in the serial port to prevent it from burned? I think
I recently completed a review of the BSCI exam for CCNP.
http://tcpmag.com/Exams/article.asp?EditorialsID=67
Best of luck to you on your next exam!
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59594&t=59594
--
FAQ, list archi
Piyush ...
1. Tools : -YM with their YM ID :-) ... but they can be in invicible
mode .. :-(
- Make simple HTML Pake with ... YM status on it [ just
like the one on the YM website again they can be invicible :-(
2. Network SNiffer Will DO however there are several c
Sorry ... My mail was sorted by ... " Subject " ..
And this subject was a long time ago ... :-) he he he
Sorry for the inconvinience ...
Piyush ...
1. Tools : -YM with their YM ID :-) ... but they can be in invicible
mode .. :-(
- Make simple HTML Pake with ... YM statu
Just another thought to consider, your counters have never been cleared.
So if this router has been up for a long time who knows if it's just
people running around in the LAN room playing with cables or doing other
work that caused these errors 6 months ago. Otherwise you may want to
look at the h
Thanks for the tip!
-Mark
-Original Message-
From: eric nguyen [mailto:[EMAIL PROTECTED]]
Sent: Thursday, December 19, 2002 8:26 PM
To: Mark W. Odette II; [EMAIL PROTECTED]
Subject: RE: PIX and the Activation Key [7:59574]
"activation-key" commands only works with version 6.2.x or
87 matches
Mail list logo
