John,
Take my advice . STAY OFF GILES ... this is the
most
confusing book I have read in my entire career as a Network Engineer . Its
full of
useless ,crappy information and trivia that will just end up confusing you
...
Jaspreet
John Neiberger wrote:
> Do any of you
And this had what to do with Cisco certification or products? It doesn't
seem that you are asking a question on advice or for an approach. You want a
total VPN plan and design to present to your customer for direct monetary
gain not for the pursuit of knowledge. Right
Pay a co
I'd recommend a 3620 in the head office, with 2611's @ the remote sites.
You need extra RAM, flash, and IP+56 feature set. As to the configs, there
are plenty of examples @ Cisco.com. I found a LOT of info on VPN. You just
have to be diligent and dig.
Michael
-Original Message-
Fro
If anyone is interested in going to Cisco Networkers (Chicago 7/16-7/20),
please let me know immediately. I have 2 passes that I can sell at
substantially less than the early registration (at least half price) . I'll
take the first reasonable offer. Please let me know ASAP as the conference
is
Hey, can everyone help me with setting up a good CCIE lab. I need to know
what equipment would be the best to purchase for the lab. I will use it to
study for both CCNP and CCIE. My budget is between $5000-$7000. Any and all
replies would be greatly appreciated.
Thanks,
Brian Clark - A+, Netwo
I don't know the answer but you might look up the timeout command on the PIX
(if that's what you have) and see if that helps.
Allen
- Original Message -
From: "James Haynes"
To:
Sent: Thursday, July 12, 2001 9:48 AM
Subject: NAT Translations and Time Left [7:12133]
> I'm performing N
Does anyone know if there is a CBT on Sniffers or similar analyzers?
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=12143&t=12143
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report mis
This brings up a point: why is there a telco version in the first
place? What are these telco requirements and why are they there? I've
been hearing little snippets about this but I don't know the details.
>From what I've read so far, it sounds like some government agency had
too much time on
Im trying to configure a my 3640 to dial a ppp server
and then route ip over that link. It will stay up
permanently until the frame connection comes back up.
Im putting a wic-2a/s into wic1 on the NM in slot 1.
First off Im not real sure how the line numbering will
go (cisco's site is pretty me
Thanks for the suggestions I will try them and let you know how it turns
out.
--
James Haynes
Network Architect
Cendant IT
A+,MCSE,CCNA,CCDA,CCNP,CCDP,
CQS-SNA/IP
""James Haynes"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I'm performing NAT translations on one of our networ
Anyone know what kind of cable to use to connect two T1 modules? I have a
2525 with the Fractional/full T1 module(RJ45) and a 2621 with the
WIC-1DSU-T1 module(RJ45). What kind of cable can I use to connect these
momdules?
Thanks
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i
Think of it as more of a "more specific match" instead. A rule for
50.0.0.0/8 is less specific than a rule for 50.5.5.5/32. I would put the
deny at the bottom of the list though
- Original Message -
From: "nrf"
To:
Sent: Thursday, July 12, 2001 8:33 AM
Subject: Some questions for
CISSP...
www.isc2.org
""Bruce Williams"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I want to get a well recognized security certification. I know about Cisco
> Security Specialist and the CCIE Security, but are there any others that
are
> more widely recognized in the indus
nrf
NRF,
I think that this may help - you have to remember that packets outgoing_src
source addresses are what are recieved on the INSIDE interface ie your local
network, outgoing_dst are the destinatio of the packets recieved.
t the fact of the matter that this does not work for me. I have
di
Greeting to all,
This problem proved to be a real bitch, and I thank you for all the advice.
Here is the fix, and I am almost ashamed to say, but I want to pass this on
so none of you all fall into the same trap as I did.
As I said, in one post before, I kept getting the same error messages ev
I'm performing NAT translations on one of our network connections and all is
fine except that the server the people are connecting to is having an
application issue. This causes them to time out waiting for a logon. They
then try to initiate another connection and the same process occurs. If I do
Hi
How about doing a "show version" to see the reason of last reboot
"Arun" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> hi
> we have catalyst 5000 in our organization and last week oneof our catalyst
> 5000 rebooted bu its own ...can anyboby tell me what could be the
proba
Search CCO for time based access lists. They are a new feature in of the
12.x's.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/ip_c
/ipcprt1/1cdip.htm#22601
-Ejay
-Original Message-
From: Thomas Surber [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, July 11, 2001 10
Each different frame type acts as a separate broadcast domain, thus they
have different network numbers.
-Original Message-
From: Elmer Deloso [mailto:[EMAIL PROTECTED]]
Sent: Thursday, July 12, 2001 8:41 AM
To: [EMAIL PROTECTED]
Subject: RE: IPX Network addresses [7:11990]
Thanks for a
I thought you could, but checked the feature navigator on CCO
http://www.cisco.com/go/fn and it looks like a 2600 running IP Plus is the
lowest end router that would.
Jim
-Original Message-
From: Ahmed Mamoor Amimi [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, July 11, 2001 4:14 PM
To: [EM
Are you using all cisco equipment or are you mixing cisco with other
vendors? If you are using multiple vendors, make sure the sap and rip
updates are happening at the same time. (either when changes are made, or
every so many seconds) a lot of vendors' default configs are to allow
updates when
Anyone have informattion, where i can find simulated exams for Cisco PIX
Advanced ?
And what best sources, prepare for this exam ?
Regards,
Edgar Alves Nastri
CCNA, CCSA, CCSE, MCSE+I, MCNE
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=12129&t=12129
-
Did you have the phone company run a line test? What is the loop length
between the two?
Is it a dry pair? You should be able to check the line quality through the
DSL modem.
You can also mess with the TX power settings.
There other question is if it ever worked. If not there may be a short
You've got a line quality problem. Since you can't drop the speed, I'd
suggest ordering a new pair from the ILEC. Additionally, you can try
hooking up the router at the NID to eliminate Premise wiring as the possible
cause. Does your DSLAM have a built in test head? We use the Lucent
Stinger D
I've got some CBT's that show it. I think they are from CBT systems or
somesuch.
-Original Message-
From: Ole Drews Jensen [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, July 11, 2001 5:37 PM
To: [EMAIL PROTECTED]
Subject: Animated OSPF, EIGRP & BGP examples [7:12028]
I was hoping that so
CISSP is used by big 5 consulting firms for credibility. See
http://www.isc2.org/ for info.
-Andrew
Whelchel
-Original Message-
From: Bruce Williams [mailto:[EMAIL PROTECTED]]
Sent: Thursday, July 12, 2001 8:16 AM
To: [EMAIL PROTECTED]
Subject: OT: Security Certificatio
Just go to the LAN Switching IOS site when you Login under Software
Upgrades. You should see an opportunity to catch release note, etc. You
will see an upgrade chart (if there is one for 4x to 5x). I had one with
the Sup 1
All the best !!!
Phil
- Original Message -
From: "Arun"
To:
Hi,
Look into checkpoint.com for CCSA and CCSE certs.
Thanks,
Sal
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Bruce Williams
Sent: Thursday, July 12, 2001 9:16 AM
To: [EMAIL PROTECTED]
Subject: OT: Security Certifications [7:12116]
I want to get a
Hello all. I'm looking for some PIX experts to help me with the following
strangeness I found while fiddling around with the Pix.
For purposes of this discussion, I am using PixOS 5.3, and I got a Pix 530
with 2 interfaces. The inside interface has a network of 192.168.1.0/24,
and the outside i
Javier,
EIGRP will support secondary addresses. However,
neighbor relationships will NOT be formed with the
secondary addresses.
Refer to:
http://www.cisco.com/warp/customer/103/eigrpfaq.html#Q1.3
A good white paper on EIGRP can be found at:
http://www.cisco.com/warp/customer/103/eigrp1.html
Javier,
EIGRP will support secondary addresses. However,
neighbor relationships will NOT be formed with the
secondary addresses.
Refer to:
http://www.cisco.com/warp/customer/103/eigrpfaq.html#Q1.3
A good white paper on EIGRP can be found at:
http://www.cisco.com/warp/customer/103/eigrp1.html
One additional thought...you'll want to test this, but I believe you will
need to put the static route on Router A, not Router D. If you just put one
on router D, you will just be defining Router A as the next hop (which it is
anyway) and then Router A would just forward it to Router C as per it's
I have seen this before on HP OpenView. SNMP is and
will still see the ip address even if it is shutdown.
You must remove the IP address of the other router
> mmmhh ! yes i shutdown the interface and then bring it up ... looks
like
> the software issue to me too anyother way i can
I want to get a well recognized security certification. I know about Cisco
Security Specialist and the CCIE Security, but are there any others that are
more widely recognized in the industry or any well know vendor independent
security certifications.
Bruce Williams
[EMAIL PROTECTED]
Message
I just passed my R&S written exam, I want to know what study materials are
best for prepping for the lab. I currently have Routing tcp/ip from Doyle
and Halabi's BGP book. I am looking for a CCIE lab book and/or CDs. Any
input appreciated.
Message Posted at:
http://www.groupstudy.com/form/
it is recommended in the BCRAN book But i didn't understande what u said
what is the fragmentation delay ?
Best Regards,
Mohammed Saro
Network Engineer
GEGA NET
Tel: +202-4149771 Ext:111
- Original Message -
From: "Charlie Hartwell"
To:
Sent: Thursday, July 12, 2001 11:53 AM
Subjec
Hi,
You need to make sure you have 32Mb RAM installed for each Supervisor
engine, even though the image still fits in 8Mb flash
Peter
""Arun"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi
> can anbody please help me with this i will be upgrading my catalyst 5000
IOS
> what
OSPF also uses "redistribute connected" to redistribute all connected
interfaces that don't belong to any OSPF area, but have IP enabled on the
interfaces. These are redistributed as external to the AS.
CM
> -Original Message-
> From: Jeongwoo Park [mailto:[EMAIL PROTECTED]]
> Sent: 12 J
you could get an older cisco cs-500. they came in both 8 and 16 port
models. You can pick one up for a couple of hundred on ebay.
Neil Schneider
""Ryan O'Reilly"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi All,
>
> I'm curious if anybody knows of any inexpensive alter
i have a problem with one DSL customer with a speed of 128 kbps conected to
my
company through 2 exchanges via copper wires 0.4 mm thick the line is up and
the protocols goes up and down i checked the H/W it is ok but the physical
line has input errors and crc's whta is the solution
Best Regards
Is any one aware of any CCNP study groups in my area? I have equipment and
want to find some serious people to study with.
E-mail or call any time.
Thanks,
--
Vik Evans - MCSE, CCNA, CCDA
[EMAIL PROTECTED]
(602) 206-5335
(480) 633-1888
Message Posted at:
http://www.groupstudy.com/form/read.p
I may be misunderstanding your topology...it would help if you posted config
excerpts.
As far as my experience has been, secondary addresses are configured in
eigrp in the same way as primary addresses. Just make sure you've included
the "router eigrp [network#]" and "network xx.xx.xx.xx" command
Thanks for all the responses. This is the only IPX speaking box on the wire
and the first NW5.1 server to be brought up. I understand that it supports
and automatically loads all IPX frame types by default if IPX is chosen
along with the default and preferred IP protocol. From the replies it seems
i have 32 MB RAM installed on it i was asking about the issues like ..which
features are resolved in newer relase and which were problem in 4.4(1)
thanks
Arun sharma
""Peter"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi,
>
> You need to make sure you have 32Mb RAM insta
hi
ur talking about dsl right how far is ur coustomer from ur prmises check
that is it on the right distance ..
Arun
""Mohammed Saro"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> i have a problem with one DSL customer with a speed of 128 kbps conected
to
> my
> company throug
mmmhh ! yes i shutdown the interface and then bring it up ... looks like
the software issue to me too anyother way i can check on the cisco
router if they still exists?
btw what is NOC ?
>From: "Chuck Larrieu"
>To: "shella kevin" ,
>Subject: RE: Duplicate Ip addresses ! [7:12100
Hi all
One is ospf's subnet command: redistribute subnet
The other is eigrp's connected command: redistribute connected
Are these two kind of same?
I know that without subnet keyword, ospf's routing table shows only major
network address that are not directly connected the redistributing router
what are you - the night shift in the NOC?
when you say you "decommissioned" the interfaces, did you issue shutdown
commands? physically pull the wires so they aren't connected to anything?
in general, issuing a shutdown command on an interface prevents it from
telling the network about itself.
hi
we have catalyst 5000 in our organization and last week oneof our catalyst
5000 rebooted bu its own ...can anyboby tell me what could be the probabale
cause or where one shoulb be looking for it ...
how do i start looking for it .Please help
this reboot has caused the services to be stopped
I am monitoring cisco routes via netview. I decommissioned 2 interfaces on
the cisco router and put it on an other outer. Now I am getting alerts on
netview " Duplicate Ip addresses" .. it's the same ip
addresses/FastEthernet interface which I decommissioned.
How can I address this problem
got your smartnet contract set up? Call 1-800-553-NETS, and the good folks
there will be happy to step you through getting your contract activated, and
your CCO login in place.
Once done, you will be able to download the software you need.
HTH
Chuck
-Original Message-
From: [EMAIL PROT
That book is good enough, concentrate on Chapters 1 thru 3 and 13 thru 14
inclusive.
When i took the exam there were very few CLI type questions, at least 70% on
putting together a security policy and PKI, IKE, ISAKMP etc.
As to CLI understand things like how to clear the NAT table, what NAT
0(Z
Hi,
I prepared using Michael Wenstrom book and Donald C. Lee`s
book (Enhanced IP Services for Cisco Networks, Chapter 6-8
ISBN 1-57870-106-6). I think Donald`s book is easy to
understand than Michael`s which looks like a manual that
anyone can download from CCO.
Understanding the concept to pass t
Hi,
I am glad that this topic is discussed here. In fact currently I am doing
a project that is trying to make use of the Port Monitoring/SPAN
feature as a form of keepalive & duplicate traffic discovery
with a third party product. I won't go into that detail.
I had read the portion of info at
I don't believe this guy will actually implement this configuration. I think
he just wants to know if it is theoretically possible.
CM
> -Original Message-
> From: Tony van Ree [mailto:[EMAIL PROTECTED]]
> Sent: 12 July 2001 06:56
> To: [EMAIL PROTECTED]
> Subject: Re: Access-list Questi
I have a vinyl player capable of attaining two speeds (can't remember what
they are), with a whopping, monstrous 5watts RPM per speaker...beat that
> -Original Message-
> From: Tony van Ree [mailto:[EMAIL PROTECTED]]
> Sent: 12 July 2001 06:52
> To: [EMAIL PROTECTED]
> Subject: RE: Co
Use static route on router D. This will overide the dynamically learnt route
to 10.1.1.0
CM
> -Original Message-
> From: Grad Alfons Kanon [mailto:[EMAIL PROTECTED]]
> Sent: 12 July 2001 06:49
> To: [EMAIL PROTECTED]
> Subject: VPN QUERY [7:12068]
>
>
> All,
>
> need help,
>
> I have
I have always thought that NetWare only auto-generated its internal network
number (based on date and time of installation, which semi-gurantees
uniqueness of the address), but the external network numbers had to be
entered manually for each frame type. I may be wrong, but I don't think it
auto-de
Hi group
Have anyone studying for MCNS 2.0 or given the exam???/
If so, what books need to be prepared apart from Cisco press book written by
Michael Wenstrom. Any comments on how the questions are, and what level of
difficulty it is. Do we need to have hands on experience on Pix or rather
studyin
Steiven,
It sounds like those users who have logged in were using PAT(single ip
nat'ed). If that's the case, then your ACS/pix can only see one single
ip. Only enhance you can change on the pix is to change the time-out to
be as low as you can without annoying users logon process.
-Frank
On
Hello,
i've got two routers sharing one common
network...one of this routers got a
secondary address defined over the
interface...
is there any way to make this secondary
net be visible on the shared network
dynamically using EIGRP
Thank you very much in advance,
_
Javi
It would be interesting to see the document that recommends that
action - after all, WFQ is designed to help with low bandwidth links
without the need for complicated config.
It is more likely that it is recommended to turn off WFQ when using
ppp multilink across the ISDN connection. This is prob
Hi
can anbody please help me with this i will be upgrading my catalyst 5000 IOS
what are the things that needed to be taken care before doing this .i
have supervisior card 2 runnnign on it and they are runnign in redudant mode
..i have 2 catalyst 5000what can be like probaable prob
hello everybody,
I have a cisco 1601 router in my office and windows Nt server
in my home.For administration reasons i want to configure the router to call
me back when i call him from home.
I also have an isdn bri line and two net modes to make the project the scheme
is:
CISCO_1600 --NET MODENET
I have A problem when i enabled CEF on a 4500 router with ios 12.0(5) T i
have
a problem that when i apply a new access-list it does not make any matches
unless i disable then reenable the ip cef on the router what is that ?
Best Regards,
Mohammed Saro
Network Engineer
GEGA NET
Tel: +202-4149771
Hello Cisco Folks,
The problem that we face is a lot unusual. We are successfully
configured the PIX with Cicso Secure ACS software on the server and
have created some user ID on the software for the authentication to
access to internet through proxy server. The good thing is it can
immediate
thank you very much.
You advices were very helpful
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=12083&t=11896
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondis
101 - 167 of 167 matches
Mail list logo
