[expert-it] modem adsl

2001-05-25 Thread a.marcedone

Io uso l'alcatel home.
Ma non c'e' problema, con adsl: la maggior parte dei modem li devi attaccare
ad una scheda di rete. Io uso una 3com (ottima) ma puoi prenderne una
compatibile.
Non comprare quelli con l'uscita USB.
Ciao



- Original Message -
From: Daniele Bamberghi [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Wednesday, May 16, 2001 9:25 PM
Subject: [expert-it] Modem ADSL


 Ciao a tutti
 visto che finalmente la mia citta' e' coperta dall'ADSL, non c'e' nessuno
 che mi puo' dare qualche informazioni su un modem ADSL buono, che funzioni
 con Linux e costi poco ? :P
 grazie in anticipoDaniele









[expert] Problem Teles ISDN 16.3c (isa pnp) with mandrake 8.0

2001-05-25 Thread John Seiler

Hello,

i have a Problem with my ISDNcard from teles. The same card with the
same parameters will work fine under Suse 7.0 and Red Hat 7.0.

Under MD 8.0 it will not establisht a internet connection.

here are some infos /var/log/messages

localhost kernel: isapnp: Scanning for PnP cards...
May 23 07:54:20 localhost kernel: isapnp: Card 'TELES.S0/16.3c
PlugPlay'
May 23 07:54:20 localhost kernel: isapnp: 1 Plug  Play card detected
total

---


HiSax: Linux Driver for passive ISDN cards
May 23 07:54:20 localhost kernel: HiSax: Version 3.5 (module)
May 23 07:54:20 localhost kernel: HiSax: Layer1 Revision 2.41.6.2
May 23 07:54:20 localhost kernel: HiSax: Layer2 Revision 2.25.6.1
May 23 07:54:20 localhost kernel: HiSax: TeiMgr Revision 2.17.6.1
May 23 07:54:20 localhost kernel: HiSax: Layer3 Revision 2.17.6.2
May 23 07:54:20 localhost kernel: HiSax: LinkLayer Revision 2.51.6.2
May 23 07:54:20 localhost kernel: HiSax: Approval certification failed
because of
May 23 07:54:20 localhost kernel: HiSax: unauthorized source code
changes  | What ist that ??
May 23 07:54:20 localhost kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax
(0)| --
May 23 07:54:20 localhost kernel: HiSax: HFC-S driver Rev. 1.8.6.1
localhost kernel: HFCS: defined at 0x580 IRQ 5 HZ 100
May 23 07:54:20 localhost kernel: HFCS: resetting card
May 23 07:54:20 localhost kernel: Teles 16.3c: IRQ 5 count 0
May 23 07:54:20 localhost kernel: Teles 16.3c: IRQ 5 count 0
May 23 07:54:20 localhost kernel: Teles 16.3c: IRQ(5) getting no
interrupts during init 1
May 23 07:54:20 localhost kernel: HFCS: resetting card
May 23 07:54:20 localhost kernel: bug: kernel timer added twice at
d0906b09.
May 23 07:54:20 localhost kernel: Teles 16.3c: IRQ 5 count 0
May 23 07:54:20 localhost kernel: Teles 16.3c: IRQ(5) getting no
interrupts during init 2
May 23 07:54:20 localhost kernel: HFCS: resetting card
May 23 07:54:20 localhost kernel: bug: kernel timer added twice at
d0906b09.
May 23 07:54:20 localhost kernel: Teles 16.3c: IRQ 5 count 0
May 23 07:54:20 localhost kernel: Teles 16.3c: IRQ(5) getting no
interrupts during init 3
May 23 07:54:20 localhost kernel: HiSax: Card Teles 16.3c not installed
!
May 23 07:54:20 localhost kernel: ISDN-subsystem unloaded

I hope anybody can help me

john

begin:vcard 
n:Seiler;John 
tel;work:030 - 80944-812
x-mozilla-html:FALSE
org:Syidos IT-Solution
adr:;;
version:2.1
email;internet:[EMAIL PROTECTED]
x-mozilla-cpt:;-15920
fn:Seiler, John 
end:vcard



[expert] Configuring VMware for raw disk?

2001-05-25 Thread Benjamin Sher

Dear friends:

I've been trying to configure VMware for my Windows 98 /mnt/windows partition.

I have an AMD K6-2 400, 128 meg of RAM. Installation of  the VMware rpm went 
off perfectly. I am speaking of the interactive installation procedure (I 
think it's  called the file vmware-config.pl).

I have a dual-boot LM 8.0/Win98 SE system. Linux is on hda and hdb and 
Windows is on hdc, with the CD-Rom is on hdd.

I read the instructions on VMware's support page, changed the permissions on 
the hda, hdb, hdc and hdd and then configured hdc as a raw disk. 

The great thing about the latest VMware 2.04  for dual-boot systems is that 
you do NOT have to actually install Windows in a virtual disk. You can just 
invoke the ACTUAL, REAL Windows on your /mnt/windows partition directly from 
within VMware. I know that to be true. I have done it. I just don't know how 
to do it right, and I would rather not proceed until I am sure of what I am 
doing.

The instructions say clearly to UNmount /mnt/windows BEFORE configuring 
VMware.

First obvious question: Do you RUN Vmware with hdc as raw disk with 
/mnt/windows MOUNTED OR UNMOUNTED? That is, do you have to UNmount 
/mnt/windows every time you run VMware in this case or do you run Vmware with 
/mnt/windows mounted?

I am afraid to proceed any further. I tried and experimented with various 
configurations, but I think it's time for me to quit experimenting. I am just 
an ordinary user and I'd rather not jeopardize my LM 8.0 installation.

I'd appreciate it if someone who has a how-to or step-by-step instructions in 
plain English for my specific situation could direct me a web site where I 
could find out how to configure Vmware properly, not only the /mnt/windows on 
a dual-boot system but all the other details that are a part of it.

Thank you.

Benjamin

-- 
Sher's Russian Web
http://www.websher.net
Benjamin and Anna Sher
[EMAIL PROTECTED]




[expert] Mandrake 8.0 and executables that don't.

2001-05-25 Thread Will Woods


Hi,
 
I have just done a fresh install of Mandrake 8.0 after having used 7.2
with no problems for some time. I am trying to install two different
commercial symbolic math packages, Macsyma Pro 2.4 and Maple V. Both
packages seem to install fine, but the executables they install are not
recognized by the system. I can list them, e.g. ls -l for Maple gives:
 
# ls -l mapleTTY
-rwxrwxr-x1 alias24 669660 Jan 11  1998 mapleTTY*
 
but trying to execute it gives the following:
 
# ./mapleTTY
bash: ./mapleTTY: No such file or directory
 
(this is not a PATH problem, it happens when I'm in the same dir as the
executable)

The same problem occurs for Macsyma. Both packages installed and ran fine
under 7.2.
 
Anybody got any ideas?

Thanks for any help
 
Will
 
  
 
 






Re: [expert] USB startup question

2001-05-25 Thread Jerry Sternesky

Neal,

This drove me insane for awhile and then I finally nailed it.  I would type 
service usb status and get not running, yet it was starting the service at 
boot. what I had to do was create a file in /etc/sysconfig called usb.  The 
contents of the file are as follows:

USB=yes
MOUSE=no
KEYBOARD=no
STORAGE=no
VISOR=yes

notice no quotes around yes and no.

Also since I am using the stock mandrake kernel, I needed to have some stuff 
in /etc/modules.conf:

alias usb-interface usb-uhci
post-install usb-uhci modprobe visor

Hope this helps you out

Jerry


On Thursday 24 May 2001 21:11, Neal Lippman wrote:
 I am trying to sort out some USB-related stuff, specifically related to the
 modules for syncing my Visor. I have all that stuff working, but it is a
 pain to have to load the modules after each boot so I can sync.

 I notice that in /etc/init.d there is a script called usb that starts up
 usb devices and should load all the visor modules as well. It seems to look
 for a subscript called /etc/sysconfig/usb, and after attempting to execute
 that script, it uses a number of shell variables (eg $VISOR) to decide
 what to do.

 Unfortunately, I don't have the /etc/sysconfig/usb script - probably
 because when I installed MDK 7.2 I didn't have any usb devices. In anycase,
 does anyone know if my understanding of this is correct? if so, it seems
 that all I would need to do is to create /etc/sysconfig/usb and put into
 it:

 $USB=yes
 $VISOR=yes

 and the modules will get loaded at boot time.

 Help, anyone?

 Neal





[expert] ximian mess

2001-05-25 Thread Bill Kenworthy

Hi,
Ive just installed ximian and have made a right mess of it!.. Does
anyone know what the configuration applet is called.  I hope to be able
to start it from an xterm within ximian and undo the damage.  The theory
is I have selected multiple windows which are overlaying the main window
and as it does not have a panel I cannot get to the configuration applet
toreselect single.  I can get an xterm by clicking on the background,
but thats all so far!




Re: [expert] adding second Hardisk

2001-05-25 Thread pedro marocas
From: Pierre Fortin <[EMAIL PROTECTED]>
To: pedro marocas <[EMAIL PROTECTED]>
CC: [EMAIL PROTECTED] 
Subject: Re: [expert] 
Date: Wed, 23 May 2001 16:05:12 -0400 
 
pedro marocas wrote: 
  
  Hi. After install a second hd(yes, i configure it in BIOS as a second master, 
  i 
  lost the jumper:( ), Mandrake8.0 start loading but stop mistyriously. Anyone 
  have any idea of what's going on? Thanks in advance 
 

Are you saying two masters on the same IDE bus...? 
No, different IDE. This is happening for the first time ever. Previous releases(Mandrake and even RedHat), never cause me this kind of failure. After showing the Loading linux message the loading simply stops.

 
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.



Re: [expert] Mandrake 8.0 and executables that don't.

2001-05-25 Thread Hoyt

On Friday 25 May 2001 05:01 am, Will Woods wrote:
 Hi,

 I have just done a fresh install of Mandrake 8.0 after having used 7.2
 with no problems for some time. I am trying to install two different
 commercial symbolic math packages, Macsyma Pro 2.4 and Maple V. Both
 packages seem to install fine, but the executables they install are not
 recognized by the system. I can list them, e.g. ls -l for Maple gives:

 # ls -l mapleTTY
 -rwxrwxr-x1 alias24 669660 Jan 11  1998 mapleTTY*



Wordperfect 8 seems to exhibit the same problems until you install 
ld.so-1.9.11-4mdk.i586.rpm. I have no idea if that package will fix it, it 
may be that the same _type_ of problem exists.

Hoyt




Re: [expert] Mandrake 8.0 and executables that don't.

2001-05-25 Thread Praedor Tempus

I have run into this several times myself.  With me, the latest such episode 
occurred with sixpack, a bibliography application for lyx.  I installed it, 
which went fine.  I then try to run it and get the same message you do.  I 
then do a which executable and it properly identifies the executable in 
the proper place. 

The executable just wont work and isn't recognized.  I then tried 
reinstalling and that appeared to do the trick.  I have run into this with 
several different programs lately: sixpack, pybliographic, k3d, and a couple 
others I can't recall right now.  

On Friday 25 May 2001 03:01, Will Woods wrote:
 Hi,

 I have just done a fresh install of Mandrake 8.0 after having used 7.2
 with no problems for some time. I am trying to install two different
 commercial symbolic math packages, Macsyma Pro 2.4 and Maple V. Both
 packages seem to install fine, but the executables they install are not
 recognized by the system. I can list them, e.g. ls -l for Maple gives:

 # ls -l mapleTTY
 -rwxrwxr-x1 alias24 669660 Jan 11  1998 mapleTTY*

 but trying to execute it gives the following:

 # ./mapleTTY
 bash: ./mapleTTY: No such file or directory

 (this is not a PATH problem, it happens when I'm in the same dir as the
 executable)

 The same problem occurs for Macsyma. Both packages installed and ran fine
 under 7.2.

 Anybody got any ideas?

 Thanks for any help

 Will

-- 
Against stupidity, the gods themselves contend in vain.




Re: [expert] getting time right

2001-05-25 Thread D. R. Evans

On 24 May 01, at 21:26, Stephen Boulet wrote:

 I really like using webmin for this. There is a nice module to synchronize 
 your system time and hardware time with a time server.
 

Done that. Makes no difference. (Except that date -u now gives an 
accurately wrong time :-) )

The Webmin thing seems to assume that the whole local/UTC thing is 
already working right; it doesn't seem to mess with those settings at 
all, and those are the ones that seem to be in need of fixing on my 
system.

  Doc Evans

--
Phone:  +1 303 494 0394
Mobile: +1 720 839 8462
Fax:+1 781 240 0527
--




Re: [expert] network printing from SCO Unix to local printer on Mandrake

2001-05-25 Thread Lars Nordin

This would be better asked on one of the comp.unix.sco.* newsgroups but here 
is the answer anyway :)

If you are using the scoadmin GUI, realize that it can only scan for other 
SCO boxes with printers (and I believe that it even says that some where on 
the menu or documentation). I have successfully configured a SCO v5.0.5 to
print to a RH v6.2 box but you will have to (if I remember correctly) just 
fill in the settings in scoadmin-printers and not run the scan; scoadmin 
will just assume the settings are correct and try and use them. I believe 
that one the Linux box will have to add an entry for the SCO box in 
/etc/lphosts (or something like that).


On Friday 25 May 2001 01:19, Darcy Brodie wrote:
 I am hoping that you can assist me with this.

 I am attempting to connect a SCO unix remote printer que to a local
 printer on a mandrake box.  I have configured and successfully tested
 the printer under CUPS, but when I attempt to locate the remote printer
 on the SCO box, it is unable to locate it.  This printer is visible and
 usable from other Mandrake machines on the network.  There is no mention
 in any of the logs on the Mandrake machine of the attempts from the Unix
 machine attempting to gain access to the printer.  I have added the IP
 and computer name to the /etc/hosts file, and allowed guest and public
 access to the printer

 I am running Mandrake 7.2, with an IBM postscript printer (This
 printer does work under the Unix, as I am replacing all our windoze and
 dos machines with Linux).  SCO Openserver ver 5.0 with updates for the
 printing and security functions

 Darcy




[expert] Upgrading from 7.2 to 8.0 over network?

2001-05-25 Thread Brian Hartman

Hi, all.

I would like to upgrade from 7.2 to 8.0.  Unfortunately, I don't have a 
CD-ROM burner, so I can't just download the ISO and install.  Is there a way 
to do an installation over a network (from an FTP site, for example?

TIA.





Re: [expert] Upgrading from 7.2 to 8.0 over network?

2001-05-25 Thread Julia A. Case

You can download the iso and mount it with the loopback device and run live_upgrade

Julia

Quoting Brian Hartman ([EMAIL PROTECTED]):
 Hi, all.
 
 I would like to upgrade from 7.2 to 8.0.  Unfortunately, I don't have a 
 CD-ROM burner, so I can't just download the ISO and install.  Is there a way 
 to do an installation over a network (from an FTP site, for example?
 
 TIA.
 

-- 
[  Julia Anne Case  ] [Ships are safe inside the harbor,   ]
[Programmer at large] [  but is that what ships are really for.]  
[   Admining Linux  ] [   To thine own self be true.   ]
[ Windows/WindowsNT ] [ Fair is where you take your cows to be judged. ]
  




Re: [expert] Oracle 8i on Linux Mandrake - SOLVED

2001-05-25 Thread Leonardo T. de Carvalho

Fox wrote:
 
 A friend of mine got it to work this week.
 
 First:
 
 unset LANG
 unset LANGUAGE
 unset LC_*
 
 Any environment variable that starts with LC_ you need to unset.  That will
 fix your SIGSEGV.
 
 Next, switch to GNOME to run the installer if some buttons don't work.  Some
 of the buttons in the Java app may not work in KDE.
 
 Okay, you are on your way.  You will need the glibc 2.1.3 stubs from
 Oracle's site as well.
 
 Fox
 [EMAIL PROTECTED]
 

Hi all.

Thanx to A.V. Flinsch. The problem are really on the
glibc files.


Best regards
-- 
Leonardo T. de Carvalho
Ibiz Tecnologia
Frase aleatória:
Under every stone lurks a politician.
-- Aristophanes





Re: [expert] email form to staroffice apps

2001-05-25 Thread Mark Belanger

[EMAIL PROTECTED] wrote:
 
 I am a student at a Southern California University.  I need to know how
 to transfer rough data in an email document (text-based data) to the
 spreadsheets or database appications in Staroffice... I know ms access
 has some of these capabilites (as I done it before), but i don't see why

Save the text of the email to a file.  In star office,
Select Open and specify the file type as txt-csv

-Mark

-- 
Mark Belanger
LTX Corporation




Re: [expert] Configuring VMware for raw disk?

2001-05-25 Thread Woody Green

Benjamin Sher wrote:

 
 First obvious question: Do you RUN Vmware with hdc as raw disk with 
 /mnt/windows MOUNTED OR UNMOUNTED? That is, do you have to UNmount 
 /mnt/windows every time you run VMware in this case or do you run Vmware with 
 /mnt/windows mounted?
 


You can run it mounted but mount it read-only (ro) if you do.  Do NOT mount
the partition rw and run VMWare at the same time.


 I am afraid to proceed any further. I tried and experimented with various 
 configurations, but I think it's time for me to quit experimenting. I am just 
 an ordinary user and I'd rather not jeopardize my LM 8.0 installation.
 


BACK UP YOUR REGISTRY.  (Both the user.dat and the system.dat)  Otherwise, you
may find yourself reinstalling Windows so you can run it on the actual PC again.
The idea is that you are going to take advantage of Window's ability to do
hardware profiling.  When I tried it (as per instructions), I destroyed my
registry and the system performed poorly on both VMWare and the actual PC.
The idea is that you create a PC profile (a hardware config that will run on the
real PC hardware) and a VMWare profile (a hardware config that matches the
VMWare virtual hardware.)  Creating the PS profile and making a profile that
will become the VMWare profile is easy, but when you boot Windows and tell it to
use the VMWare profile (booting in VMWare of courrse) it begins the hardware
detection and starts adding the drivers necessary to run on VMWare.  This is
fine except that when Windows adds the drivers, it adds them to both profiles.
So as you are building your VMWare profile you corrupt your original PC profile.
You square away your VMWare profile once you get it done and reboot the real PC
back into Windows and choose the PC profile (note: if you can get the profiles
working correctly Windows will supposedly smartly pick the profile that matches
the hardware it sees at boot.)  It's then you notice your PC profile drivers
have both the real drivers and the VMWare drivers.  So you go into the PC
profile and remove the VMWare drivers being careful to choose Remove driver
from this profile only and get your PC profile all cleaned up.  Once you have
your PC profile all working again, you go back to trying it in VMWare and
discover that some of the drivers in the VMWare profile are missing and now it
has some of the PC drivers.  So you start the cleaning process from the VMWare
profile perspective...

  while (1) {lather; rinse; repeat;} /* infinite loop */

After about the third attempt, Windows begins to fail to boot altogether due
to registry corruption.  At this point, you restore the registry backup you
made before this mess got started and make another new partition on which to
install Windows inside of VMWare and run with Windows dual installed.

The short of it is that any driver added always gets added to all profiles and
any driver removed will affect all profiles enough whether or not you choose
Remove from this profile only such that when booting that profile the
hardware detection begins again causing all sorts of fun, ad infinitum.

Just my experience,

  Woody


 I'd appreciate it if someone who has a how-to or step-by-step instructions in 
 plain English for my specific situation could direct me a web site where I 
 could find out how to configure Vmware properly, not only the /mnt/windows on 
 a dual-boot system but all the other details that are a part of it.
 
 Thank you.
 
 Benjamin
 
 







Re: [expert] Configuring VMware for raw disk?

2001-05-25 Thread Julia A. Case

Have you or anyone else had luck running VMWare under the new 2.4.x kernels?  I 
can't get the modules to compile

Thanks

Quoting Benjamin Sher ([EMAIL PROTECTED]):
 Dear friends:
 
 I've been trying to configure VMware for my Windows 98 /mnt/windows partition.
 
 I have an AMD K6-2 400, 128 meg of RAM. Installation of  the VMware rpm went 
 off perfectly. I am speaking of the interactive installation procedure (I 
 think it's  called the file vmware-config.pl).
 
 I have a dual-boot LM 8.0/Win98 SE system. Linux is on hda and hdb and 
 Windows is on hdc, with the CD-Rom is on hdd.
 
 I read the instructions on VMware's support page, changed the permissions on 
 the hda, hdb, hdc and hdd and then configured hdc as a raw disk. 
 
 The great thing about the latest VMware 2.04  for dual-boot systems is that 
 you do NOT have to actually install Windows in a virtual disk. You can just 
 invoke the ACTUAL, REAL Windows on your /mnt/windows partition directly from 
 within VMware. I know that to be true. I have done it. I just don't know how 
 to do it right, and I would rather not proceed until I am sure of what I am 
 doing.
 
 The instructions say clearly to UNmount /mnt/windows BEFORE configuring 
 VMware.
 
 First obvious question: Do you RUN Vmware with hdc as raw disk with 
 /mnt/windows MOUNTED OR UNMOUNTED? That is, do you have to UNmount 
 /mnt/windows every time you run VMware in this case or do you run Vmware with 
 /mnt/windows mounted?
 
 I am afraid to proceed any further. I tried and experimented with various 
 configurations, but I think it's time for me to quit experimenting. I am just 
 an ordinary user and I'd rather not jeopardize my LM 8.0 installation.
 
 I'd appreciate it if someone who has a how-to or step-by-step instructions in 
 plain English for my specific situation could direct me a web site where I 
 could find out how to configure Vmware properly, not only the /mnt/windows on 
 a dual-boot system but all the other details that are a part of it.
 
 Thank you.
 
 Benjamin
 
 -- 
 Sher's Russian Web
 http://www.websher.net
 Benjamin and Anna Sher
 [EMAIL PROTECTED]

-- 
[  Julia Anne Case  ] [Ships are safe inside the harbor,   ]
[Programmer at large] [  but is that what ships are really for.]  
[   Admining Linux  ] [   To thine own self be true.   ]
[ Windows/WindowsNT ] [ Fair is where you take your cows to be judged. ]
  




Re: [expert] getting time right

2001-05-25 Thread Alexander Skwar

So sprach D. R. Evans am Thu, May 24, 2001 at 06:30:20PM -0600:
 Fine. Now please tell me how you did it :-)

Hmm, well, I don't know.  I just selected it at install time, and that's it. 
Maybe the thing is that my hardware time is running on UTC?  Maybe you
should try that?

And DrakConf also contains something for setting time.  Does this not work?

Well, that's my /etc/sysconfig/clock:

ARC=false
UTC=true
ZONE=Europe/Berlin

Lastly, I'm setting my clock once per day to the official times provided by
official sources, ie. for europe ptbtime1.ptb.de and for US ntp2.usno.navy.mil

To do this, I use this mini script:

#!/bin/sh
SERVERS=ptbtime1.ptb.de ntp2.usno.navy.mil

ntpdate $SERVERS

. /etc/sysconfig/clock

OPTS=--systohc

[ .$UTC = .true ]  OPTS=${OPTS} --utc

hwclock ${OPTS}

Alexander Skwar
-- 
How to quote:   http://learn.to/quote (german) http://quote.6x.to (english)
Homepage:   http://www.digitalprojects.com   |   http://www.iso-top.de
   iso-top.de - Die günstige Art an Linux Distributionen zu kommen
Uptime: 5 hours 1 minute




Re: [expert] getting time right

2001-05-25 Thread D. R. Evans

On 25 May 01, at 22:11, Alexander Skwar wrote:

 So sprach D. R. Evans am Thu, May 24, 2001 at 06:30:20PM -0600:
  Fine. Now please tell me how you did it :-)
 
 Hmm, well, I don't know.  I just selected it at install time, and that's it. 
 Maybe the thing is that my hardware time is running on UTC?  Maybe you
 should try that?
 

Yeah; I was hoping to avoid that, but all the people who seem to have 
the time working correctly appear to be running with a UTC hardware 
clock. I'll mess with it over the weekend unless someone steps forward 
with a solution that works with a local-time BIOS clock.

 And DrakConf also contains something for setting time.  Does this not work?
 

Nope. Not if the BIOS clock is running on local time. (At least, it 
doesn't do the right thing on my system. Somehow, it doesn't figure out 
the right UTC time even though there appears to be enough information 
available in the two config files for the system to be able to work it 
out.)

Thanks for the other info. I will be using SNTP to keep the time 
correct once I have this UTC/local mess sorted out.

  Doc

--
Phone:  +1 303 494 0394
Mobile: +1 720 839 8462
Fax:+1 781 240 0527
--




[expert] Tuxracer with NVidia drivers on Mandrake 7.2?

2001-05-25 Thread Michael Leone

Hey all

I downloaded tuxracer .61 SRC RPM from rpmfind.net (I had to use the RH
7.1 sources, since all the Mandrake sources groused about not finding
libSDL, even tho I did install it), and rebuilt it (Linux Mandrake 7.2).

Anyway, the RH7.1 RPM rebuilt fine, but I couldn't install it, since it
says

[root@minas-aran i686]# rpm -ivh --test tuxracer-0.61-2.i686.rpm 
error: failed dependencies:
libGLcore.so.1 is needed by tuxracer-0.61-2

Now, I have a Diamond Viper V770 graphic card; this is a NVidia TNT2
based graphic card. I'm running the latest 1.0-251 NVidia drivers, with
no problems, on XFree86 4.0.2. The NVidia GLX driver installation
removes the default libGLcore, and replaces it with their own. 

I did a search, and found /usr/lib/libGLcore.so.1. 

lrwxrwxrwx1 root root   21 May 19 22:00 libGLcore.so.1
- libGLcore.so.1.0.1251*
-rwxr-xr-x1 root root  3457056 May 19 21:59
libGLcore.so.1.0.1251*

(IOW, libGLcore.so.1 is a symlink to NVidia's replacement libGLcore)

And /usr/lib *is* in my ld.so.conf, so it should be found and linked.
And my XF86Config-4 does say load GLX, and does *not* say load GLcore,
per NVidia's instructions.

So what can I do now? I've been thru NVidia's site, to no effect, nor
has a web search turned up anything useful.

-- 
 
--
Michael J. Leone  Registered Linux user #201348 
mailto:[EMAIL PROTECTED]ICQ: 50453890
PGP Fingerprint: 0AA8 DC47 CB63 AE3F C739 6BF9 9AB4 1EF6 5AA5 BCDF

In Pennsylvania, it it illegal to sleep on top of a refrigerator outdoors.
 





Re: [expert] Mandrake 8.0 and executables that don't.

2001-05-25 Thread Hoyt

On Friday 25 May 2001 10:43 am, Will Woods wrote:
 I seem to get a conflict with ldconfig-2.2.2-4mdk when I try and install
 it.  Can I force it to install (and is that advisable?)

 Thanks for your help.

 Will



I have not yet applied the fix to my computer, but a friend has to his (and 
forced it) with no apparrent problems . . . BUT . . . it's not a smart thing 
to do unless you are able to recover and repair your system in case of 
trouble.

Hoyt




[expert] Wrong memory detection

2001-05-25 Thread Sarang Lakare

Hi,

I am having problems with correct memory detection on two machines. Both 
machines have 1.5GB and LM8.0 on both of these detects 1.0GB. On one of the 
machines, 7.2 was installed earlier and it detected 1.5GB correctly.

1. ASUS K7V (VIA) Motherboard

2. SGI Zx10 workstation

I have tried appending mem=1536, mem=1500 etc but no help. Any ideas? 

Who is to blame? the linux kernel or the hardware vendor? 

thnaks!
sarang




Re: [expert] Tuxracer with NVidia drivers on Mandrake 7.2?

2001-05-25 Thread Todd Flinders

Yeah, I've been fighting similar problems for weeks. 
I have been trying to compile smpeg 4.2 or 4.3 and
they won't find GL.  They always disable opengl
support because it cannot be found.

You might try compiling the nvidia drivers from
tar.gz.  I was going to try that next.  Most
applications work for me, but there are some (another
is the Sin video game) that are having a real hard
time with the nvidia drivers.

Any help with this would be GREATLY appreciated.

--- Michael Leone [EMAIL PROTECTED] wrote:
 Hey all
 
 I downloaded tuxracer .61 SRC RPM from rpmfind.net
 (I had to use the RH
 7.1 sources, since all the Mandrake sources groused
 about not finding
 libSDL, even tho I did install it), and rebuilt it
 (Linux Mandrake 7.2).
 
 Anyway, the RH7.1 RPM rebuilt fine, but I couldn't
 install it, since it
 says
 
 [root@minas-aran i686]# rpm -ivh --test
 tuxracer-0.61-2.i686.rpm 
 error: failed dependencies:
 libGLcore.so.1 is needed by tuxracer-0.61-2
 
 Now, I have a Diamond Viper V770 graphic card; this
 is a NVidia TNT2
 based graphic card. I'm running the latest 1.0-251
 NVidia drivers, with
 no problems, on XFree86 4.0.2. The NVidia GLX driver
 installation
 removes the default libGLcore, and replaces it with
 their own. 
 
 I did a search, and found /usr/lib/libGLcore.so.1. 
 
 lrwxrwxrwx1 root root   21 May 19
 22:00 libGLcore.so.1
 - libGLcore.so.1.0.1251*
 -rwxr-xr-x1 root root  3457056 May 19
 21:59
 libGLcore.so.1.0.1251*
 
 (IOW, libGLcore.so.1 is a symlink to NVidia's
 replacement libGLcore)
 
 And /usr/lib *is* in my ld.so.conf, so it should be
 found and linked.
 And my XF86Config-4 does say load GLX, and does
 *not* say load GLcore,
 per NVidia's instructions.
 
 So what can I do now? I've been thru NVidia's site,
 to no effect, nor
 has a web search turned up anything useful.
 
 -- 
  

--
 Michael J. Leone  Registered Linux
 user #201348 
 mailto:[EMAIL PROTECTED]ICQ: 50453890
 PGP Fingerprint: 0AA8 DC47 CB63 AE3F C739 6BF9 9AB4
 1EF6 5AA5 BCDF
 
 In Pennsylvania, it it illegal to sleep on top of a
 refrigerator outdoors.
  
 
 


__
Do You Yahoo!?
Yahoo! Auctions - buy the things you want at great prices
http://auctions.yahoo.com/




Re: [expert] getting time right

2001-05-25 Thread Alexander Skwar

So sprach D. R. Evans am Fri, May 25, 2001 at 02:35:31PM -0600:
 Yeah; I was hoping to avoid that, but all the people who seem to have 

Uhm, why did you want to avoid that?  Long, long ago *G* when I was still
running Windows occiasionally, I also had my clock set to UTC.  Now, since
Windows sucks and isn't able to deal with a clock set to UTC, I've installed
a SNTP client in Windows, which ran right at bootup.  This caused the clock
to be set to the wrong time (ie. local time), but at least Windows was fine. 
In Linux I also had this SNTP script running, so really everything was fine.

 Nope. Not if the BIOS clock is running on local time. (At least, it 

Dunno, I've got my BIOS clock on UTC for quite some time now and will not
change it.

Alexander Skwar
-- 
How to quote:   http://learn.to/quote (german) http://quote.6x.to (english)
Homepage:   http://www.digitalprojects.com   |   http://www.iso-top.de
   iso-top.de - Die günstige Art an Linux Distributionen zu kommen
Uptime: 0 hours 30 minutes




Re: [expert] getting time right

2001-05-25 Thread D. R. Evans

Got it working!

But it sure doesn't seem very logical.

1. Set BIOS clock to UTC.
2. Set /etc/localtime to link to the correct timezone.
3. Set UTC=false (yes, false!) in /etc/sysconfig/clock

Now date and date -u both work, as does the regular clock on the 
desktop. 

Even though I received several private e-mails suggesting that some 
people have managed to configure the time correctly with a BIOS clock 
set to local time, nothing I tried made that work successfully.

  Doc Evans

--
Phone:  +1 303 494 0394
Mobile: +1 720 839 8462
Fax:+1 781 240 0527
--




Re: [expert] Tuxracer with NVidia drivers on Mandrake 7.2?

2001-05-25 Thread Haim Ashkenazi

Hi

did you install Nvidia's drivers as rpm or from a tar file? (just for curiousity, if
you installed it from rpm try 'rpm -qf /usr/lib/libGLcore.so.1'). it doesn't really
matter, if that's the only thing missing then just install it with the 'nodeps'
option: 'rpm -ivh --nodeps rpm file'. although this is usually not recomended, if
you know you have the file that rpm complains about then you can use this option. 

[EMAIL PROTECTED], [EMAIL PROTECTED] wrote:

Hey all
I downloaded tuxracer .61 SRC RPM from rpmfind.net (I had to use the RH
7.1 sources, since all the Mandrake sources groused about not finding
libSDL, even tho I did install it), and rebuilt it (Linux Mandrake 7.2).
Anyway, the RH7.1 RPM rebuilt fine, but I couldn't install it, since it
says
[root@minas-aran i686]# rpm -ivh --test tuxracer-0.61-2.i686.rpm
error: failed dependencies:
libGLcore.so.1 is needed by tuxracer-0.61-2
Now, I have a Diamond Viper V770 graphic card; this is a NVidia TNT2
based graphic card. I'm running the latest 1.0-251 NVidia drivers, with
no problems, on XFree86 4.0.2. The NVidia GLX driver installation
removes the default libGLcore, and replaces it with their own.
I did a search, and found /usr/lib/libGLcore.so.1.
lrwxrwxrwx1 root root   21 May 19 22:00 libGLcore.so.1
- libGLcore.so.1.0.1251*
-rwxr-xr-x1 root root  3457056 May 19 21:59
libGLcore.so.1.0.1251*
(IOW, libGLcore.so.1 is a symlink to NVidia's replacement libGLcore)
And /usr/lib *is* in my ld.so.conf, so it should be found and linked.
And my XF86Config-4 does say load GLX, and does *not* say load GLcore,
per NVidia's instructions.
So what can I do now? I've been thru NVidia's site, to no effect, nor
has a web search turned up anything useful.
--

--
Michael J. Leone  Registered Linux user #201348
mailto:[EMAIL PROTECTED]ICQ: 50453890
PGP Fingerprint: 0AA8 DC47 CB63 AE3F C739 6BF9 9AB4 1EF6 5AA5 BCDF
In Pennsylvania, it it illegal to sleep on top of a refrigerator outdoors.


-
- -
Haim




Re: [expert] Tuxracer with NVidia drivers on Mandrake 7.2?

2001-05-25 Thread Michael Leone

On 25 May 2001 21:44:55 +, Haim Ashkenazi wrote:
 Hi
 
 did you install Nvidia's drivers as rpm or from a tar file? (just for curiousity, if
 you installed it from rpm try 'rpm -qf /usr/lib/libGLcore.so.1').

I never install NVidia's stuff from anything but tarballs. I have 3
different kernel versions that I boot to, for different things. I just
compile a driver under each kernel version.

And it's all working; I can even run other GL based stuff (gears gives
me 500+ fps); it's just tuxracer that won't install.


-- 
 
--
Michael J. Leone  Registered Linux user #201348 
mailto:[EMAIL PROTECTED]ICQ: 50453890
PGP Fingerprint: 0AA8 DC47 CB63 AE3F C739 6BF9 9AB4 1EF6 5AA5 BCDF

In Pennsylvania, it it illegal to sleep on top of a refrigerator outdoors.
http://www.dumblaws.com/states/pennsylvania.html





Re: [expert] Upgrading from 7.2 to 8.0 over network?

2001-05-25 Thread s

Find you a site close by and download the network.img file and direct copy it 
to a floppy.  dd if=network.img of=/dev/fd0  (or is it /mnt/floppy?)
make sure you have the exact address to the ftp site/Mandrake directory 
written down for reference cause it don't hunt for you.  This is a pretty 
cool way to do it, especially for the lazy person (like myself) cause then 
everytime you need to add something, it'll look on the site instead of asking 
for cdroms.  :-)
-s
ftp://helios.dii.utk.edu/pub/linux/Mandrake/Mandrake/current/i586/images/README


On Friday 25 May 2001 09:22 am, you wrote:
 Hi, all.

 I would like to upgrade from 7.2 to 8.0.  Unfortunately, I don't have a
 CD-ROM burner, so I can't just download the ISO and install.  Is there a
 way to do an installation over a network (from an FTP site, for example?

 TIA.





[expert] Problems with my page...

2001-05-25 Thread Craig Sprout

Thanks to all of you who have taken time to contribute your comments and
help to my little FAQ project.  I hope to get some more work done on it
this weekend, and hopefully double the current number of FAQ's.

I had some problems over the past 24 hours, and as much as I would like
to say that it was due to some horrific DSL provider, it was mainly due
to a not-too-bright administrator type who wasn't paying a lot of
attention to what he was answering yes to!  I'm not naming names, but
let's just say maybe that guy shouldn't be starting and maintaining a
plastic flower garden, much less a FAQ.

Anyway, it's back up and going.  The address SSP MODE=ON again is
http://www.mtsprouts.net/craig/expertfaq.php, or if you have something
to add yourself, go here:  http://www.mtsprouts.net/craig/addfaq.php.

Thanks again for your patience, help and contributions.

--Craig






Re: [expert] getting time right

2001-05-25 Thread David Rankin

D. R. Evans wrote:
 
 On 24 May 01, at 21:05, David Rankin wrote:
 
  D. R. Evans wrote:
 
   On 25 May 01, at 0:47, Alexander Skwar wrote:
  
So sprach D. R. Evans am Thu, May 24, 2001 at 03:28:29PM -0600:
 This causes date to respond correctly, and the clock on the screen to
 display the correct time, but date -u gives the wrong time.
   
Define 'wrong' time.  My system clock is running on UTC and I live in CEST
zone (GMT/UTC +0200):
   
[askwar@teich pear]$ date
Fre Mai 25 00:47:16 CEST 2001
[askwar@teich pear]$ date -u
Don Mai 24 22:47:18 UTC 2001
   
Everything's fine.
   
  
   Fine. Now please tell me how you did it :-)
  
   I told you what I did (following the documentation in Linux
   Installation, Configuration and Use for Red Hat systems), and that
   gives me the wrong UTC time. Here, being a perverse sort of chap, I
   define wrong as not right :-)
  
   [n7dr@localhost n7dr]$ date
   Thu May 24 18:29:18 /etc/localtime 2001
   [n7dr@localhost n7dr]$ date -u
   Thu May 24 18:29:21 UTC 2001
  
 Doc Evans
  
   --
   Phone:  +1 303 494 0394
   Mobile: +1 720 839 8462
   Fax:+1 781 240 0527
   --
 
  Your softlink from etc/localtime to America/Denver isn't set
 
 
 
 Well, that's what I thought too. But:
 
 [n7dr@localhost n7dr]$ ls -al /etc/localtime
 lrwxrwxrwx1 root root   30 May 24 15:13 /etc/localtime - 
/usr/share/zoninfo/US/Mountain
 
   Doc
 
 --
 Phone:  +1 303 494 0394
 Mobile: +1 720 839 8462
 Fax:+1 781 240 0527
 --

Whoa Doc, the message your replying to wasn't sent by me - David Rankin.
I think it was a reply to my response to you. I really think you and I
are talking about the same phenominon. You linux file stamps are 6 hours
in the future and the time samba serves for me is 5 hours in the future
(localtime not set) 10 hours in the future with localtime set to
America/Chicago. Hmmm.. something strange, but consistent is going on
here. Hopefully someone reading will have some additionaly insight as to
why time is slightly warped in our systems.
-- 

David Rankin
Rankin*Bertin, PLLC
Nacogdoches, Texas




Re: [expert] getting time right

2001-05-25 Thread Ron Stodden

 Hopefully someone reading will have some additionaly insight as to
 why time is slightly warped in our systems.

One of my Mandrake 8.0 machines suddendly put itself on UTC and I was
not able to restore it to running the hwclock on localtime.

Much later: By copying from the good machine I was able to restore
the hwclock to operation on local time, so necessary for Windows
operation.

The /etc/localtime file had been clobbered by a localtime directory
which was a copy of the entire contents of:

/usr/share/zoneinfo/

Deleting the localtime directory and restoring a /etc/localtime file
from the contents of:

usr/share/zoneinfo/Australia/Melbourne

and setting /etc/sysconfig/clock to:

ARC=false
UTC=false
ZONE=Australia/Melbourne

solved the problem.  The desktop panel, date, date u, xdaliclock and
kworldwatch all now show correct values, as does the system after an
ntpdate adjustment.

=
BTW, the file names mentioned in man hwclock are completely
erroneous, and there is no man for ntpdate (see
/usr/share/doc/ntp/ntpdate.htm).
=

-- 
Ron. [au]

Kindly note my new email address: [EMAIL PROTECTED]
and new web site: http://www.ains.net.au/~ronst/




Re: [expert] Upgrading from 7.2 to 8.0 over network?

2001-05-25 Thread s

Yep when you're ready to install.  It will work exactly the same as if you 
had cdroms in there (except for setting up your network parameters and ftp 
site info first).
-s


On Friday 25 May 2001 09:12 pm, you wrote:
 On Fri, 25 May 2001, s wrote:

 After I do this, I just boot from the floppy?

  Find you a site close by and download the network.img file and direct
  copy it to a floppy.  dd if=network.img of=/dev/fd0  (or is it
  /mnt/floppy?) make sure you have the exact address to the ftp
  site/Mandrake directory written down for reference cause it don't hunt
  for you.  This is a pretty cool way to do it, especially for the lazy
  person (like myself) cause then everytime you need to add something,
  it'll look on the site instead of asking for cdroms.  :-)
  -s
  ftp://helios.dii.utk.edu/pub/linux/Mandrake/Mandrake/current/i586/images/
 RE ADME
 
  On Friday 25 May 2001 09:22 am, you wrote:
   Hi, all.
  
   I would like to upgrade from 7.2 to 8.0.  Unfortunately, I don't have a
   CD-ROM burner, so I can't just download the ISO and install.  Is there
   a way to do an installation over a network (from an FTP site, for
   example?
  
   TIA.