Bandwidth Management

Hi I would like to know how to do bandwidth control using 6509 with MSFC. Basically, I have a number of VLANS created and I would like to limit the amount of bandwidth for each VLAN. (eg. VLAN10 - 1Mbps) Also, can this be done on a per port basis? Thanks in advance. regards Kevin

Problem with CiscoSecure ACS v2.3 for NT

I normally access the admin port of CiscoSecure ACS v2.3 for NT with browsers, Internet explorer 5.0 or Netscape 3.0. After adding a new user account "phtmi2" I click submit, the system will appear to freeze and come back in another 5 to 10 minutes that it cannot display the page. However, for som

RE: bgp and ospf and synchronisation

I'll elaborate a bit more. My fault. The BGP route in question is actually being learnt by OSPF and is in the route table. On BGP peers which have an EBGP session, that route is in the BGP prefix table, but comes in as "not sync..." when doing a sh ip bgp x.x.x.x Now, when I put it a static ro

Re: bgp and ospf and synchronisation

It seems to me that you've answered your own question. I currently run OSPF <--> BGP without the command 'no sync" on my EBGP peers. I've you carefully read the rfc, or any BGP related document you'll discover that two requirements must be meet in order for BGP to fully synchronized. The 2 requ

Re: Cisco versus Juniper at the corelayer

A little trivia for you - the "M" stands for Martini I've had a little exposure to Junipers - a course and some configuration. The OS (JUNOS) has a lot of similarities to IOS which is not suprising as the company was started by former Cisco employees. As others have pointed out they are selling

BCMSN question

Dear group, I have a question that is if a switch can simultaneously belong to more than one vtp domain? thanks in advance. dean **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posti

Re: booksamillion

Hi, I've used booksamillion to purchase about 8 books, being delivered to the UK. Even with the overseas postage they are still cheaper than local WEB sites, such as Amazon.co.uk, though they do take longer to arrive. So I only order books from them that I'm not in hurry for. I would imagine t

about the LED status

hi guys: i did the BCMSN test today,it is more diffcult than i think.i meet a question: the catalyst 5500 connect catalyst 2924 with UTP line. the LED light will be on always on both side. or catalyst 5k LED light will be off after 20 second. or catalyst 2924 LED light will be off after some se

Re: Just CCO online test Information

Guys, Does cisco take note and record on your results from these tests? Thanks Brandon -Original Message- From: Vincent <[EMAIL PROTECTED]> Newsgroups: groupstudy.cisco To: [EMAIL PROTECTED] <[EMAIL PROTECTED]> Date: Tuesday, September 26, 2000 6:19 AM Subject: Just CCO online test I

Re: Network Analyzer - Slightly OT

Chuck, I have EtherPeek, running on a DELL latitude, with W2K Pro. I use the following: Farallon **Fast EtherTX-10/100 PN995-TX CardBus (21143) CRC, Alignment, *Runt, Oversize *Use special Digital driver with EtherPeek 4.0.2 and later for capture of error packets. See Readme.txt

RE: CID exam Information Wanted

As Chuck has suggested. Read all questions carefully. This will be the most obscure exam you will probably sit to date. Make sure you study hard and give this exam more respect than any of the CCNP exams. Good luck. P.S. you can go back so mark the dodgy questions and go back at the end. --

Exam for CCDP Cert

Hi ! Can anyone tell me if there are 2 exams to take for CCDP after CCNP or just the one. Thanx. **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: http://www.groups

IOS

Hi ,   I know i am sound stupid in asking this question... but still want ask and am in NEED of ans...    Can anyone give me the structure of IOS ?   u know like u have kernel -- shell and filesystems as in unix/solaris Os. anylinks to this will be of great help.   thanks in advance,

Re: Exam for CCDP Cert

if you hold ccda, 1, if not, requrie DCN +CID "Cisco Kid" <[EMAIL PROTECTED]> wrote in message 8qps76$16o$[EMAIL PROTECTED]">news:8qps76$16o$[EMAIL PROTECTED]... > Hi ! > > Can anyone tell me if there are 2 exams to take for CCDP after CCNP or just > the one. > > Thanx. > > > **NOTE: New CCNA/CC

routing

Hi Consider the following setup: |--Internet | Upstream Provider--Router A | |--Router B Consider Router A to have two links (1 and 2) to the upstream provider and also Router B to have two links to the upstream provider (1 and 2) Would it be possible to route traffic f

RE: Just CCO online test Information

Hi, How can one get a CCO login to write these tests? Do these exams count for certification trackc (i.e. CCNP/CCDP)? And are the exams free? Thanks in advance. J-M -Original Message- From: Brandon Peyton [mailto:[EMAIL PROTECTED]] Sent: 26 September 2000 11:04 To: Vincent; [EMAIL PR

CIT 2.0

Does anyone have any information for the CIT 2.0 exam that they would be able to send me that would be helpful? I just barely failed it the first time and do not want to do that again. **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associ

Re: Exam for CCDP Cert

you need ccna ccda routing switching and remote access (or foundation routing & switching) cid that is what gets you CCDP CCNP is ccna routing switching and remote access (or foundation routing & switching) cit "Cisco Kid" <[EMAIL PROTECTED]> wrote in message 8qps76$16o$[EMAIL PROTECTED]">news

BSCN MANUAL at LAST!!!

After searching the earth and back, I have finally just bought a copy of the official Cisco BSCN manuals (two in total) and believe me it's the bomb!! I'm happy about my purchase cos I am confident that all I need to study for the Routing exam is available in one place rather than studying blin

WCCP

Hi All, In the docs and CLI I have studied and successfully implemented WCCP v1 for web-cache to a Linux Server running Squid 2.4 with WCCP support compiled in and it works great! However this is just for web traffic and it refers to other possible redirects that can be done which I assume to in

IP Browsers

Can anyone recommend a good IP Browser? I know Solarwinds.net has one , but is their any others out there. **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: http:/

Re: 911....Help Needed "soft error" Token Ring

You are trying to solve something that is not a real problem . The message : Last Ring Status 00:32:29 (0x2000) indicates that the last status was a soft error . Mostlikely because insertion/removal of a station in the ring ( 1/2 hour ago ) . This is not a problem . Are actually see a problem

RE: BSCN MANUAL at LAST!!!

I will be taking the BSCN course through GlobalKnowledge next week. Will the class manual suffice as a good study guide. Are there any other books that I should read? I do have access to an old ACRC manual. I'd appreciate any feedback. Thanks!! Robert Lopez Network Planning Pfizer -Origi

Re: booksamillion

I think their prices are good, but they are not so good if you need it that week. Under www.bestbookbuys.com they come up as the cheapest quite often, but I have had to waite as much as a 5 to 7 days just for something to be shipped (no counting travel time). Other than that- OK with me... Phil

Re: 911....Help Needed "soft error" Token Ring

THANKS GUYS!! Flem wrote: > You are trying to solve something that is not a real > problem . The message : > > Last Ring Status 00:32:29 (0x2000) > > indicates that the last status was a soft error . > Mostlikely because insertion/removal of a station

NetRanger

Hi all: I need information about any software to detect intruders, so I heard something about NetRanger, which is used for intrusion detect, but i don´t know if this software is in my Cisco IOS or is independent. How can I know it?, is It really efficient for this purpose? Anybody had used this??

Other Way of Seeking Recruitment

You are the same Guy who just Apologised & again trying for Recruitment on the same List. Are you NUT? Good Luck with Your Recruitment. Regards MK CCNA 2.0, MCSE, CNE *** "Dave Swink" <[EMAIL PROTECTED]> wrote: > My company (a co-

CCIE written vs CCNP 2.0

I've recently passed the CCIE written, and am now studying to take the lab. However, since I work for a reseller, I need to have an actual certification to be eligible for some of the specialization requirements. Has anyone taken the CCIE written before the CCNP tests? If so, did you need to

RE: NetRanger

It is now called Cisco Secure Intrusion Detection System. I do not believe it is built within the IOS. It is sold as a separate box. I have never used it but I hear it is pretty slick. http://www.cisco.com/warp/public/cc/pd/sqsw/sqidsz/index.shtml Chuck Collins CCNP -Original Message-

Re: Password for 2501

Here's the link for the index of all password recoveries: http://www.cisco.com/warp/public/474/index.shtml "Danny Mok" <[EMAIL PROTECTED]> wrote in message Hi all, We have a Cisco router 2501 sitting between the Internet and our firewall. A network infrastructure change involves a configuratio

Re: Routing BSCN cramsession/quick study guide

Thanks, Lauren. It looks really good. Lauren Child wrote: > > Hiya, > > Found this while browsing and as I hadnt seen it I fugure other people > may not have. > > http://www.getccnp.com/ > > In the Cramsession area it has a very good (IMHO) study guide for the > Routing exam. > > TTFN > Laur

RE: booksamillion

I like using http://www.addall.com because it searches 30+ online bookstores and calculates the best price with shipping. As I am sure a lot of you have run into the sites that have the cheapest price on an item, BUT when you add in "THEIR" shipping price it ends up being allot more than the othe

RE: Converting RIP to EIGRP (Online)

I think that MentorLabs has a V-lab that covers this exact thing... It's been a while since I was out there, but I seem to remember doing this conversion on their system once or twice... Dale [=`) >From: "Chuck Larrieu" <[EMAIL PROTECTED]> >Reply-To: "Chuck Larrieu" <[EMAIL PROTECTED]> >To: "

ethernet is up, line protocol is down

Hi guys - perhaps you can clairify something for me. According to CIT - this means layer 1 is up, but layer 2 is down (paraphrase) - what I need to know is the reprecussions of this - In other words, can I ping this interface ip address from within the router? Could I do a sh ip route on thi

Re: about the LED status

Gary - DON'T tell people what the questions on the exam were... You did accept the Non-Disclosure Agreement, right? That means that you can't tell people what's on the test. You can't say: "I just took the test and I got this question that says blah, blah, blah... What's the correct answer?"

Re: BSCN MANUAL at LAST!!!

If you are studying to pass the test, the class books have all the info in it that you will need (assuming GK uses the official Cisco material.) If you really want to _know_ the subject matter, it wouldn't hurt to study other material as well, such as stuff on the Cisco site. ---JRE--- ""Lopez,

looking to purchase.. off topic

HI, Looking for a used ls-100 with at least two mmf oc-3 interfaces and two NP type oc-3 interfaces for 4XXX series routers. Neddless to say I am hoping to find reasonable pricing on these. Thanks, Curtis _ Get Your Priva

Re: about the LED status

As long as that link is OK the LED will stay on. Now, a quiet word about the NDA When you take these tests Cisco get a bit upset if you go around repeating the questions - and so do people who already have CCNP. You clicked an "accept" button before the test started that had in the small-pri

2948G-L3 Samples

Subject says all. I haue one, and, as reputded, they can be, "no end of trouble" to get working. Oh, per-port routing is not bad--- integrhting VTP, IRB, ISL and BVIs is the slick way and not intuitiue tor either router oriented people, nor for those more familiar with L2 switches. Truely a c

RE: BSCN MANUAL at LAST!!!

Jim, Could you be more specific as to what "stuff" on the cisco site to concentrate on to increase my knowledge on the subject matter. I truly appreciate your input. Thanks! Regards, Robert -Original Message- From: Jim Erickson [mailto:[EMAIL PROTECTED]] Sent: Tuesday, September 26

Re: ethernet is up, line protocol is down

Hmmm... Ping, IP Address - all layer 3 stuff, right? Can't do layer 3 if layer 2 is down... You can do a "no keepalive" on an ethernet interface to bring it up without actually pluggin it into anything. Is that what you are trying to do? Try that and see if you get the results you are looking

Cisco Cable Manufacturer

Does anybody know a Cisco approved Cable Manufacturer? (V.35 and octal async cables). There used to be an approved list on their web site, but I can no longer find it. Any help would be appreciated. Thanks. **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupst

NAT Static....give IP conflict...

Hello groups,   I'm using NAT on Cisco 3000 running ios 12.1.  I also using NAT Static to mapping port. (i.e ip nat inside source static tcp 10.0.0.254 80 64.x.x.x 80 ).  It works fine... but sometime when I reboot computer have ip 10.0.0.254 and computer display IP conflict error (its showi

Greater Cincinnati Cisco Users Group

We are starting a Greater Cincinnati Cisco Users Group. We are getting a feel for the interest level, etc. If you would like to be part of this, please send email to [EMAIL PROTECTED], [EMAIL PROTECTED] or [EMAIL PROTECTED] You can also visit our web site, which is under heavy contruction, at www.

FW: booksamillion - GREAT SOURCE

Did do a reply all and Tony was the only one who received this... I would like to know who has also had 'actual' experience with www.half.com as to their cust. stat. -Original Message- From: Aderion Brewer Sent: Monday, September 25, 2000 10:51 PM To: tv Subject: RE: booksamillion - GREA

ICQ ports

Hi,   Which ports(TCP, UDP) does ICQ use?   Thanks.

RE: ethernet is up, line protocol is down

This interface will not be able to be pinged locally.Any routes that refernece this will not show until this port becomes active. Bring up the port and all will be fine Andrew -Original Message- From: Rue Barb the Tangled [mailto:[EMAIL PROTECTED]] Sent: 26 September 2000 16:37 To: [EM

chat session??

Do we have the chat session today? What is the URL actually i am not able to remember. Pls. tell me the URL again. Anyone having knowledge on VoIP(Voice over IP)?? I am facing some problem with my setup. Thanks in advance Hitesh **NOTE: New CCNA/CCDA List has been formed. For more information

Equipment

Title: Equipment This is just a shameless plug but a well deserved one at that. I just purchased a few pieces of equipment from Brad Ellis (www.optsys.net) and I have to say that he did a great job!  The equipment all arrived that same week in great condition.  Kudos on the turn-around time

Losing connectivity to the pix

Hi All I am losing my connectivity to the pix after the reboot everthing is fine. Any clues. Thanks in advance regards rajeev = Rajeev Karamchand MCSE,MCSE+I,MCDBA,CCNA __ Do You Yahoo!? Send instant messages & get email alerts with Yahoo

Re: ICQ ports

ICQ 2000 uses tcp 5190, and ICQ uses tcp/udp 4000   Lonnie ""Bulent Sahin"" <[EMAIL PROTECTED]> wrote in message 001501c027cf$c6e083d0$[EMAIL PROTECTED]">news:001501c027cf$c6e083d0$[EMAIL PROTECTED]... Hi,   Which ports(TCP, UDP) does ICQ use?   Thanks.

FDDI Bridges

I am working to understand how Cisco handles FDDI bridges, but I can't see to find a definitive answer on what I need. I know that if you have 2 bridges that are connected via FDDI and they each have Ethernet hosts on the other side the ethernet hosts can communicate with each other because of en

RE: booksamillion

I've had good experiences with BooksAMillion but that's because they have a retail store (and it is huge) in a mall here in Charlotte, NC. I'm not sure if these are all over the place or not. Brian -Original Message- From: Thompson, JefferyX L [mailto:[EMAIL PROTECTED]] Sent: Tuesday, S

RE: ethernet is up, line protocol is down

Title: RE: ethernet is up, line protocol is down See comments below: -Original Message- From: Rue Barb the Tangled [mailto:[EMAIL PROTECTED]] Sent: Tuesday, September 26, 2000 10:37 AM To: [EMAIL PROTECTED] Subject: ethernet is up, line protocol is down Hi guys - perhaps you can c

Re: ethernet is up, line protocol is down

NO you will not be able to ping it. You will not see it in the show ip route command. If you want to bring it up just for testing then you can enter the command "no keepalive" in the interface configuration mode to bring it up but do that for testing only and once its up you can ping it and also

RE: ethernet is up, line protocol is down

That's the command I was trying to remember - NO KEEPALIVE - - Looks like the route is propagating now. I guess that guy did try to plug it into a MAU or something. Thanks guys. RB >From: "Guyler, Rik [EESUS]" <[EMAIL PROTECTED]> >To: Rue Barb the Tangled <[EMAIL PROTECTED]>,"Cisco G

Migrating from EIGRP to OSPF

Hi, all, Does anyhone have any links, documents, etc. about migrating from EIGRP to OSPF? Any gotchas in the process? Basically, I am looking for recommendations/comments on the most efficient way to do this such that the change is not visible on the network. Given that the AD of EIGRP is lowe

Re: ethernet is up, line protocol is down

Try setting no keepalives on the interface. It will appear to be up even though nothing is plugged in. HTH, Casey >From: "Rue Barb the Tangled" <[EMAIL PROTECTED]> >Reply-To: "Rue Barb the Tangled" <[EMAIL PROTECTED]> >To: [EMAIL PROTECTED] >Subject: ethernet is up, line protocol is down >D

Re: FW: booksamillion - GREAT SOURCE--Half.com

I ordered a book from www.half.com the Friday before Labor Day. They are required to get conformation of shipping from the seller within 2 days and didn't, due to the holiday, so they cancelled the order and notified me. I then re-ordered it, and also was notified that it was cancelled in er

RE: booksamillion - GREAT SOURCE

I have used half.com. The experience depends on the seller. I ordered six book one time. They were all coming from different sellers. Some books came within a week and some took a couple of weeks. For the savings it was worth it if you don't need the book right away. Before you order read the revi

RE: ICQ ports

Part of every networking person's repertoire should be:   http://www.iana.org/numbers.htm   contains the most recent port assignments and a whole lot more.   in another mail you were told ports 5190 and 4000.   5190 is registered to AOL ( whom I believe owns ICQ? )   port 4000 is registere

BSCN; Inter vs.Intra

Thank all. I still have a hard time with these two; intra and inter. I still get confused. In the OSPF with multiple areas, it describes how stub area carries Intra-area and Inter-area routes but not routes external to the AS. Is intra-area routes, routes with in the area? Is inter-area route

RE: Converting RIP to EIGRP (Online)

Good thought, Dale. And if you've never been there before, they offer one freebie to new folks. http://www.mentortech.com/vlab/onl.shtml -Original Message- From: Dale Holmes [mailto:[EMAIL PROTECTED]] Sent: Tuesday, September 26, 2000 7:35 AM To: [EMAIL PROTECTED]; [EMAIL PROTE

Re: chat session??

Paul has an excellent chat room setup at www.groupstudy.com OR you are certainly welcome to use mine at: www.allnetllc.net/chat/ciscochat.htm Have fun. What is your VoIP problem? Dale [=`) >From: [EMAIL PROTECTED] >Reply-To: [EMAIL PROTECTED] >To: [EMAIL PROTECTED] >Subject: chat session?? >

Searching CCO

Dear Group, After studying for seven or so exams, and now studying for the CCIE written, I'm getting "not bad" at searching CCO. However, I've drawing a blank try to find a link that will explain the feature set for Service Provider IOS. I found out by accident that Service Provider IOS doesn't

RTP port numbers

Cisco recommends using: ip rtp 16384 16383 bandwidth for RTP. Out of the range 16384-32767 that VoIP uses, how does it use the port numbers? What ports are used for fax? I have looked on Cisco's website and I have not been able to find any good information on this. Also, these are UDP ports.

RE: Cisco Cable Manufacturer

http://www.LoDanWest.com is one. > -Original Message- > From: Tim McCabe [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, September 26, 2000 10:06 AM > To: [EMAIL PROTECTED] > Subject: Cisco Cable Manufacturer > > > Does anybody know a Cisco approved Cable Manufacturer? (V.35 > and octal a

NetRanger

Has anybody ever used NetRanger? Is it a worthwhile device? Also, can you monitor crc errors with it? Any information would be much appreciated. Thanks, Stan Rossetti Russia Services Group Email: [EMAIL PROTECTED] Phone: (256) 544-5031 Beeper: 544-1183 pin # 0112 <<...>> **NOTE: Ne

Re: ICQ ports

I have seen that ICQ also uses ports 23647, 13492 and 18838. -Original Message-From: Chuck Larrieu <[EMAIL PROTECTED]>To: Bulent Sahin <[EMAIL PROTECTED]>; [EMAIL PROTECTED] <[EMAIL PROTECTED]>Date: 26 Eylül 2000 Salý 19:04Subject: RE: ICQ ports Part of eve

ATM Config

and while I'm asking getting lots of use out of the lab here.. I've got 3 4700/4500s with an ATM interface, a 7505 with ATM and an LS-1010. Using a config from Hutnick, I can't seem to get connectivity. On page 287 for the cmd "sh atm vc", Status is shown as "ACTIVE". I only

Anyone got pricing on a WIC 1 ADSL ?

Anyone got access to pricing on this new module:WIC-1 ADSL ? http://www.cisco.com/warp/public/cc/pd/rt/1700/prodlit/ads17_ds.htm Cheers _ Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. Share infor

ROM to boot

Here is the console message. What has happened to the router? Is it using ROM to boot? How to fix that? Help! System Bootstrap, Version 11.0(10c), SOFTWARE Copyright (c) 1986-1996 by cisco Systems 2500 processor with 2048 Kbytes of main memory >

RE: Anyone got pricing on a WIC 1 ADSL ?

Frank, the pricing tool my employer uses puts the list price at $750.oo I understand the plan is that this module will become supported in the 26xx and 36xx series by year end. The same pricing tool shows that Cisco is offering a 1720-ADSL package for $1695. I have not pursued this in terms of

RE: Searching CCO

Title: RE: Searching CCO Kevin, I took a look for you and didn't find much either.  I did find an info page on the SP IOS, but it is rather weak.  Since I don't know what type of bridging you want to do, this link may still help or at least point in the right direction. http://www.cisco.com/w

Re: Migrating from EIGRP to OSPF

Hey, Brian, Thanks for the info. I have some comments/clarification. >EIGRP carries a lower administrative distance vs. EIGRP. CR: You mean EIGRP (90) has a lower AD than OSPF (110)? So you can >basically turn up OSPF on your routers, and then when it all looks kosher, >what I would do is r

CCNP testing

    What order would be MOST recommended for taking the 4 CCNP 2.0 tests?  Also, any reviews on the exam cram books?  Any suggestions on better books to prepare with?

RE: ATM Config

Kevin, Not sure with out seeing your config but try mapping the destination address of the PVC: int ATM2/1 ip address 220.1.1.1 255.255.255.0 atm pvc 10 0 32 aal5snap map-group trythis ! map-list trythis ip 220.1.1.2 atm-vc 10 -Scott > -Original Message- > From: [EMAIL PRO

Re: ATM Config

Also, don't forget to ensure that PVC switching is configured correctly on the LS1010; Something like this on each LS1010 interface that the routers are connected to. atm-pvc 44 102 interface atm 1/1/1 200 This is the same thing you did with the frame relay route command. HTH, Charles ""sd

Re: ROM to boot

in that mode type: o/r0x2102 -- o is letter O -- 0x2102 is Zero X 2102 - Original Message - From: "Hubert Pun" <[EMAIL PROTECTED]> To: "Cisco Study Group" <[EMAIL PROTECTED]> Sent: Tuesday, September 26, 2000 11:36 AM Subject: ROM to boot > > Here is the console message. What has

RE: ROM to boot

Is that the whole message? If so, then yes it is booting from ROM. Generally, Cisco routers do this because the router can't find a valid image in flash. Mike -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Hubert Pun Sent: Tuesday, September 26, 2000 2

RE: Searching CCO

Here is a good link to descriptions and features of the specific Service Provider IOS sets. They talk about the 7000 series and 12000 series and the different options, but it will tell you what is supported and what isn't. Hopefully this will answer any questions that you may have concerning the

RE: Migrating from EIGRP to OSPF

Would you guys cut it out! Now I've got another lab idea to try out, to whit: if you install OSPF over EIGRP, what will the OSPF side of things look like? I.e. the spf tables? I am confident in predicting that the routing table will contain only the EIGRP routes, because those would be prefer

Re: Migrating from EIGRP to OSPF

Chuck, The SPF/neighbor/database stuff of OSPF will pretty much look the same as if its routes were inserted in the table; the thing is that the OSPF routes will be sitting around looking bored because they are NOT in the routing table... kind of like my high school years when no one would dance

RE: Anyone got pricing on a WIC 1 ADSL ?

Well it wasn't listed on the updated price listing (9/26), so after checking the link that you sent I found this: "The model numbers and information for the Cisco 2600 and 3600 will be available CYQ1 2001." I'm assuming that pricing will be available at that time also, but you might want to chec

Fw: Exam for CCDP Cert

Just the one i.e. CID #640-025, try the Sybex Book by Robert Padjen ISBN 0782126391 which got a few good comments on the group, but apparently the Exam is a pig! You only get to be a CCDP 1.0 though which probably means you recertify in two not three years. Karl - Original Message - From:

Re: access list command

Try this for a start. http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/np1_c/1cprt2/1cip.htm#xtocid1182915 Martin-Guy Richard wrote: > > Hi Group, is there somekind of Access-List How To somewhere that you can > refer me to? > > And also, to the ones who helped me install

Cisco CCIE work on Foundry???

Will a CCIE or a company employing one entertain a consulting fee from a company running Foundry Switches all piped into a cisco switch. Anyone know of a company located near Atlanta to take on that kind of short consulting job? Gary Butler **NOTE: New CCNA/CCDA List has been formed. For more i

RE: NAT Static....give IP conflict...

You might try to back out to 11.4 I had the some NAT issues with 12.X; back down to 11.4 fixed it! Also B4 doing that; U might try to check the translation table when U R having the problem.   Hao Vu INS -Original Message-From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On B

Re: Losing connectivity to the pix

exactly what is happening at the time of connectivity loss ? without more detail I would guess that your sessions are timing out and you need to increase the timeouts. Rajeev Karamchand wrote: > > Hi All > > I am losing my connectivity to the pix after the > reboot everthing is fine. Any clues.

RE: ROM to boot

Looks like the config-register has been set wrong, or someone changed it for a password recovery. >From that mode (rommon), type o/r 0x2102 to reset the config-register, and type i to reinitialize the router. Hope it helps, Joel Studtmann -Original Message- From: [EMAIL PROTECTED]

Re: (no subject)

Has anyone tried password recovery using the new Cosmo IOS, Using the information from this web site http://www.cisco.com/warp/public/474/pswdrec_6000MSFC.html I cant get the config-registry to change from 2x2102 any suggestion. Please write me back at this address **NOTE: New CCNA/CCDA List h

Sync serial modem

A few months ago, I bought a synchronous serial modem from one of the list members.  A Penril Alliance v.32 box, with a normal-looking DB-25 RS-232 connector on the back, marked "DTE".  The manual says the modem is connected to the DTE device to the DTE connection.   I now want to hook it u

RE: Exam for CCDP Cert

I thought that Cisco is using the CID #640-025 for the 2.0 track. I read somewhere on the site that it counts towards the 2.0 certification. It is only slated for a future update, but for now. The 2.0 path lists the 025 exam. http://198.133.219.25/warp/public/10/wwtraining/certprog/lan/prog

Cisco Secure VPN client

Anyone knows the product number for the software? I have VPN-SW-DES-100= but it is just the license. TIA. Ken **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.groupstudy.com/list/Associates.html _ UPDATED Posting Guidelines: htt

Traceback tool?

Hi guys (gals), I am looking for a traceback decoder and I know one is available on CCO but I can't seem to locate it! I asked the TAC to try to look but he gets several thousand hits on return...anyone have the url link? Sincerely, David Luong CCNP,CCNA,Network+,A+,i-Net+ Telecommunication

Re: ATM Config

Thanks for your post as well as others.. I have since got it working. And it's hard to say why. I asked a co-worker who had used this lab before to suggest things. We essentially wiped all the configs and started from scratch. It worked on the first attempt. (but I did that! - twice!!

RE: how many ls1010s in the lab?

How many ls1010s are in the lab is irrelevant. They are not listed on the equipment list for the lab so you will not be responsible for configuring them. Any configuration required on the ls1010s will be performed by the proctor. To answer your question though, I suspect it varies from locat

RE: ip classless, Not exactly correct

At 08:41 PM 09/24/2000 -0500, Yee, Jason wrote: >With this command if a route is not found in the routing table it will take >the gateway of last resort if it is set . > >Without this command it will just drop the packet if a classful route is not >found in the routing table. > >Jason > Without

DR/BDR in OSPF

Question about OSPF: Once the DR/BDR are elected and network is converged, if a change is detected, does the router noticing the change flood the area or send this info to the DR so it can flood the area? Rob **NOTE: New CCNA/CCDA List has been formed. For more information go to http://www.grou

RE: Traceback tool?

I'll bite. What's a traceback decoder? TIA, Mike > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On > Behalf Of Luong, David > Sent: Tuesday, September 26, 2000 3:42 PM > To: 'Cisco Group Study' > Subject: Traceback tool? > > Hi guys (gals), > >

  1   2   >