of a folded full-length (i.e. 1/4 wave long) element.
Folding short elements to make up for electrical length is something else
entirely different. The Orr twin-lead antenna that I remember was 125 feet
long, making it a full 1/4 wave on 160.
73, Ron AC7AC
-Original Message-
From: elecraft-boun
of the antenna.
A 1/4 wave long folded radiator has a feed point resistance of 4x the
typical 1/4 wavelength radiator, quite independent of the ground system.
Hence the efficiency is higher.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun
.
73 Ron AC7AC
-Original Message-
most of those posting have confused feedpoint Z with radiation resistance.
There's a nice graph in the ARRL Antenna Book showing radiation resistance
of a vertical as a function of height.
73, Jim K9YC
the assembly
instructions. Even so, we occasionally make a mistake.
73, Ron AC7AC
-Original Message-
But there's ONLY ONE in the entire kit, as the OP stated (above).
Presumably it has go to somewhere... but from a scan of the assembly
instructions, I can't find it either.
73
SO-239 connectors on the rear
panel (Fig 20, page 18).
2 are used to mount the Power Entry module on the rear panel (Fig 22, page
19).
7 are used to mount the rectifier board on the Z-bracket (Fig 29, page 23).
3 are used in the top cover interlock actuator (Fig 63, page 42).
73, Ron AC7AC
-angle radiation.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Dale Putnam
Sent: Saturday, September 28, 2013 11:49 AM
To: elecraft@mailman.qth.net; k2vco@gmail.com
Subject: Re: [Elecraft] Antenna
containing 50 or 100 words without lots of repeats.
With that criteria, common variations in the band over that time will swamp
out very small changes in signal strength. Personally, I don't get excited
about a change unless it can make a 6 to 10 dB difference.
73, Ron AC7AC
-Original
on HF due to all the
propagation variations. (Back then, 10 meters was a UHF band.)
I always thought that was why Collins settled on 6dB for one S-unit on their
receiver S-meters.
73, Ron AC7AC
-Original Message-
I think there is a lot of evidence that 3dB does not matter. 10dB matters
in the way of an improvement.
And maybe it's the variations among operators that make the discussion
unending. My tests suggested to me that what the radio engineers of the past
used was pretty close to what I'd want.
73 Ron AC7AC
-Original Message-
This argument will never die
speaker. I mean it's painfully loud!
You might want to do some troubleshooting, starting with looking for a short
circuit in the speaker wiring. IIRC, plugging in the speaker backwards will
kill the audio level by grounding the hot audio lead.
73,
Ron AC7AC
-Original Message-
From: elecraft
. Those who managed to reverse the connector and short the
audio line (fairly easy to do) often reported weak, low-level audio rather
than no audio at all. It would be great if that was all that was the matter
with your K2's audio.
73, Ron AC7AC
-Original Message-
From: elecraft-boun
on
another Ham band, so it was not obvious to the operator.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of kc2vmp
Sent: Wednesday, September 25, 2013 8:34 AM
To: Bob
Cc: Elecraft
Subject: Re: [Elecraft] P3 Feature
once again finds himself the object of a pileup. In their favor, I must say
that while reading the mail I've yet to hear DX station who didn't respond to
the calls politely.
73, Ron AC7AC
-Original Message-
...so there I am tuning across 20 meters and the band seems dead. Having
Also, human vision has the lowest acuity in the red region. That is, we see
less detail in red illumination.
73, Ron AC7AC
-Original Message-
FYI, if you're going to do as Wayne suggests and just turn the display off
aiming a light at it (saving battery drain also) red is NOT the color
.
And *no* automated stations are allowed. A control operator *must* be
present at all times.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill Frantz
Sent: Monday, September 23, 2013 7:59 PM
To: elecraft@mailman.qth.net
is high for any reason. So all the KAT500 will see during
the TUNE operation is whatever power you are driving the amplifier with -
certainly less than 50 watts.
If you are running your rig barefoot without the amp, you can run it at 100
watts during a TUNE operation without trouble.
73, Ron
Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill Frantz
Sent: Wednesday, September 18, 2013 2:47 PM
To: Larry Royster
Cc: elacraft reflrvto 2
Subject: Re: [Elecraft] W2 PROBLEM
Have you checked the ALC setting
their receiver with a gadzillion dB over S-9 signal.
Of course it only worked once, but was good for a laugh followed by a cup of
coffee or an '807' or two.
73, Ron AC7AC
-Original Message-
I was recently able to check in with my KX-3 for the first time in a year.
All it took
. The
difference would be that the guys with the elixir usually gave you something
that would produce a nice buzz (or hangover if you overdid it).
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of aj4tf
Sent: Thursday
the English (or is it
American?) language.
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Rick Bates
Sent: Thursday, September 12, 2013 7:33 PM
To: Bruce Beford
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] OT
RF
from the rig on a new frequency.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of K5HM
Sent: Monday, September 09, 2013 1:30 PM
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] KAT500 and SB 200 Amp
as you note from the specs.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Mike Flowers
Sent: Monday, September 09, 2013 2:17 PM
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] KAT500 and SB 200 Amp
Hi Ron
conductors.
73, Ron AC7AC
-Original Message-
The PowerWerx red/back paired wire ---is--- together, exactly like
zip-cord and can be easily un-zipped.
73!
K0PP
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman
and
earbuds without danger of damaging it.
With that criteria, the little KXPD1 is a perfect choice for me.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Doug Turnbull
Sent: Saturday, September 07, 2013 12:10 PM
the amplifier with the top cover removed.
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Brian Linn
Sent: Saturday, September 07, 2013 6:39 PM
To: elecraft@mailman.qth.net
Cc: supp...@elecraft.com
Subject: [Elecraft] RE
under K3 ENHANCED CABLING on page 24.
You aren't the first to miss it. The next rev of the manual will make that
instruction more obvious.
73, Ron AC7AC
-Original Message-
Hi Bruce. Check CONFIG:PWR SET on the K3. I'm pretty sure that you need to
have it set PER BAND.
The KPA500 manual
2 cents.
Ron
KB6G
K3 S/N 1997
P.S. I still give the K3 a 5+
- Original Message -
From: Bill b...@w2blc.net
To: elecraft@mailman.qth.net
Sent: Friday, August 30, 2013 8:05 PM
Subject: [Elecraft] K3 - using Clear Speech Speaker
Is anyone using the West Mountain
.
73, Ron AC7AC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support
.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Barry LaZar
Sent: Monday, September 02, 2013 4:32 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] 43 Ft Vertical and Elecraft Tuners
I know this isn't
Aaargh. I meant the more ground independent the antenna becomes not less,
above 14 MHz. That is the nature of the ground is less of a concern when the
radiator is at least 1/2 wavelength long.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft
Hi Stan:
If you don't mind waiting a few days, I'll be glad to drop a 4.7 ohm 1/4 W
resistor in the mail to you. I'm over on the Oregon coast.
If so, send me your postal address in a private message.
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
. That works great for low
frequency and audio stuff.
As long as you are breathing you are young enough to learn and enjoy new
things. Give it a shot! You might discover a world of fun!
73, Ron AC7AC
-Original Message-
On Aug 29, 2013, at 4:15 PM, Ralph Parker wrote:
If you use
.
73, Ron AC7AC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support
occasional DX,
running 1 to 2 watts with my homebrew rigs, a Heathkit HW-8 and then the
KX1, into a variety of antennas. Some were random wires strung up where
convenient and, when I had the space and time, a doublet up in the clear.
73, Ron AC7AC
of the pleasures of CW on the Ham bands for me
because almost every one of those Hams who I've had the pleasure meeting is
trying hard to improve.
I'm a firm believer in doing something badly at first, if necessary, in
order to learn.
73, Ron AC7AC
voice instead of
humans talking.
73, Ron AC7AC
-Original Message-
The good news is that I learned to recognize ships by their sound and ops by
their fist before I ever heard their call. :-) The surprising thing to me
then and still now is that the ham CW bands were filled
directly on it.
The ones I have handle heavy duty extension cords and look adequate for RG8
coax
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Walter Underwood
Sent: Tuesday, August 20, 2013 2:59 PM
That makes sense. Brian wrote RX - the abbreviation for receiver - by
accident in his original post.
So he wants two K3s connected together with an outboard TR switch that will
allow either one or both to transmit without damaging the receiver front end
on the other.
73 Ron AC7AC
be
able to apply for licenses and take the exams on-line so the rig log on and
get the license and we humans won't have to bother ourselves with what the
rig is doing.
73, Ron AC7AC
__
Elecraft mailing list
Home: http://mailman.qth.net
.
That said, of course some new products will fit a person's needs better than
ones the purchased earlier, so they will upgrade and replace. The
technology, the products Elecraft offers and the needs and interests of
individual Hams change over time.
73, Ron AC7AC
On 8/18/2013 3:39 PM, Trevor Dunne
the preamp off to see if it affects my ability to hear the other station.
Putting too much gain at the antenna input compromises the performance of
any receiver
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf
A lot of the later D-104's were manufactured with ceramic elements instead.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Brian Denley
Sent: Thursday, August 15, 2013 7:23 PM
To: Brian North
Cc: Elecraft
.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Mike WA8BXN
Sent: Tuesday, August 13, 2013 11:58 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Antennas in the attic
Remember things are different
to reassemble your KX3: replace the encoder,
tuning knob, ribbon cable, batteries, and reassemble the case halves.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Arno Dienhart
Sent: Monday, August 12, 2013 2
.
I wrote the KX3 kit assembly manual and there may be some shortcuts one can
take. I was trying to be complete for those who might have a
factory=assembled unit.
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf
delivered.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of David Eckert
Sent: Sunday, August 11, 2013 3:54 PM
To: Elecraft@mailman.qth.net
Subject: [Elecraft] question hi current/kpa out of control
I really
radio
is reproducing much of anything above 5 kHz. That's especially true of car
radios that suppress the higher frequencies to reduce background noise on
weaker A.M. stations.
73, Ron AC7AC
__
Elecraft mailing list
Home: http
frequency sensitivity, lots
of holes throughout one's hearing range, and chronic tinnitus.
Back in the 60's the Army said that was normal hearing for a 20-something
year old soldier. It's an experience one doesn't forget; my ears still ring,
literally.
73, Ron AC7AC
-Original Message
Right Al, it takes 10 kHz of RF bandwidth with A.M. to produce 5 kHz of
audio bandwidth after demodulation.
I thought my comment was clear in context. The thread was about the
desired/necessary audio bandwidth. My apologies for the confusion. I should
have said audio bandwidth.
73, Ron AC7AC
pulsar. I had no interest in
learning that it was 9:56 a.m. when all I wanted to know was that it was
almost 10.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of VE3WDM
Sent: Sunday, August 04, 2013 2:25 PM
break those pins off at the male connector. (That's what I did.)
73, Ron AC7AC
-Original Message-
From: dse...@dseven.org [mailto:dse...@dseven.org] On Behalf Of iain
macdonnell - N6ML
Sent: Thursday, August 01, 2013 9:00 PM
To: Ron D'Eau Claire
Cc: bwru...@gmail.com; Elecraft Reflector
Where do you see two DB15 cables in a diagram Brian?
Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Brian F. Wruble
Sent: Thursday, August 01, 2013 4:57 PM
To: Cady, Fred
Cc: Elecraft Reflector
Subject: Re
Interrupter shown in Figure 2 that opens the PTT
line in the DB15 cable.
73 Ron AC7AC
-Original Message-
From: dse...@dseven.org [mailto:dse...@dseven.org] On Behalf Of iain
macdonnell - N6ML
Sent: Thursday, August 01, 2013 7:01 PM
To: Ron D'Eau Claire
Cc: bwru...@gmail.com; Elecraft Reflector
straight through.
If you want to use a separate PTT cable for any reason, Figure 2 shows how
to do that. That's usually because one needs to interrupt the PTT like such
as to inhibit a Stepper-IR controller which cannot tune with full QRO power
applied.
Thanks,
Ron AC7AC
From: Brian
using the KPA500 with the KAT500, in the Utility Program click
Optimize for KPA500 to adjust the settings to take full advantage of the
capabilities of the K-line equipment (see Amplifier Key Interrupt Power on
page 29 of the KAT500 Owner's Manual).
73 Ron AC7AC
-Original Message-
From
antenna. If the noise level drops by
an S-unit or so, you have all the gain your KX3 can use. Any more just
reduces the dynamic range making the receiver more susceptible to overload.
73 Ron AC7AC
Hi Klaus,
I tried to provoke some AM breakthrough with my active antenna in
april and used
retuning indicates
the antenna system is quite efficient. Low Q - wide SWR bandwidth - in an
electrically short antenna is a solid indication there are losses in the
system.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net
on when I first became interested in radio. The
first radio station I ever copied on the homebrewed crystal
radio I made was from Florida. Not bad since I live in
Eastern PA.
72 and Thanks,
Ron Polityka
WB3AAL
www.wb3aal.com
www.n3epa.org/
K1 - SN 01011
K2 - SN 01392
but it was certainly galena.
http://tinyurl.com/knpukag
73, Ron AC7AC
-Original Message-
Yes it most probably was galena, not geranium (wrong spell check choice !),
and the crystal was about 3/8 in diameter, and height, and maybe mounted
in Woods Metal not lead. Many years later, it seems
/kl82klk (compressed URL to Amazon.com offering)
I prefer LED types having had enough fluorescent backlights die on me over
the years, Hi!
Works FB for me. Of course, the size depends on how much space you have, how
far away from you it is placed, etc. Mine is about 2 feet from me.
73, Ron AC7AC
satisfaction, and perception
is not always based on objective data.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Doug Person
Sent: Tuesday, July 23, 2013 2:25 PM
To: elecraft@mailman.qth.net
Subject: Re
It was pointed out to me that the resolution of the Acer 20 inch monitor is
not mentioned. I run mine at 1280x1024
It does not support 1440X900.
73, Ron AC7AC
-Original Message-
I just grabbed an Acer 20 inch that was on sale for under $100 at a local
store.
20-inch (diagonal
Yep, and an errata to the kit assy manual has been created. Thanks for the
comment.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Ian Kahn - Ham
Sent: Tuesday, July 23, 2013 4:53 PM
To: gdaug...@stanford.edu
cleanly without leaving any
scraps behind.
Bill said he worked that technique out installing the K3 synthesizer boards
that also have lock washers on the opposite side of the board from the screw
head.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
connector opening.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Brian Alsop
Sent: Saturday, July 20, 2013 8:42 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3EXREF query
Anybody install with with the subrx
on
each band to perform the alignment.
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Dave B
Sent: Thursday, July 11, 2013 1:20 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KX3: automated sideband
the internal speaker, but that is not surprise to me.
Further, the K3 has a multi-band audio equalizer accessed through the menu
that allows you to tailor the audio bandpass to your liking.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun
I think it's a good question, but I cannot answer it.
Most amps produce more distortion the more power they run.
The question is whether the sum of distortion from both amps at lower power
is less than one amp running at higher power.
73, Ron AC7AC
-Original Message-
On 7/18/2013 3
and my
admittedly high noise level, I used to have annoying levels from 20 through 6.
I now have no detectable VFO noise. If I ever find a truly quiet spot in the
suburban RF racket, I will check further. For now, I am happy.
Ron W3ZV
to her four
grandchildren, aged between seven and 14, so that when they are older, they
realise that this is the way messages were sent, once upon a time.
73, Ron AC7AC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman
on
the general public there. And the photo of the sounder and key was nice.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Phil Kane
Sent: Sunday, July 14, 2013 5:23 PM
To: elecraft@mailman.qth.net
Subject
Per the Owner's manual the next step after reinstalling firmware is to
reinitialize the parameters and reload your configuration file (pg 66 of the
manual).
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of aa
. They will lead you through any additional troubleshooting and then,
if the problem isn't fixed, give you the information for returning it for
factory service.
73, Ron AC7AC
From: aa...@aol.com [mailto:aa...@aol.com]
Sent: Saturday, July 13, 2013 7:19 PM
To: r...@cobi.biz; elecraft
Yep. AFAIK it was Telex (land-line based hard copy texting between terminals
for businesses) that added lower case letters to the keyboard.
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Mark Petiford
Sent
The biggest issue is that the RF is generated in the plasma display itself and
it is radiated directly through the screen (which is transparent to RF).
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of WM3M
the current limit is set for 3A and
the normal transmit current is 1.5A to 2A. A too-high SWR will cause the HI
CUR to appear.
If that happens to you due to the SWR being a bit too high, you can protect
the K2 finals by reducing the power.
73 Ron AC7AC
-Original Message-
From: elecraft-boun
Customer support - always an excellent resource!
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Brian F. Wruble
Sent: Wednesday, July 03, 2013 4:21 PM
To: Elecraft Reflector
Subject: [Elecraft] KPA500 270V
Hi Brian:
Other things to check are the connections to the rectifiers. They are also
spade connectors, any one of which could cause an intermittent. And, of
course P6 connecting to the PA assembly.
There are few things worse than an intermittent.
73, Ron AC7AC
From: Brian F
Rather superfluous now that the call sign no longer identifies the FCC
engineering district of the home station.
That was one of the all-time bad moves by the FCC, IMHO, but it was popular
among Hams who moved out of the district but couldn't bear to give up their
call sign.
73, Ron AC7AC (ex
reference for vertical antennas is Vertical Antenna Classics
published by the ARRL (ARRL Order No. 5218, ISBN 0-87259-521-8)
73, Ron AC7AC
-Original Message-
...If elevated radials are not tuned and not quarter wave, the efficiency
may be even higher than with quarter wave radials but the feed
by the vertical itself. It's all a matter of arranging
things to radiate more from the vertical and having less absorbed by the
earth.
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Barry LaZar
Sent: Monday
to the spacing and travel are made by two small Allen
wrenches supplied with the KXPD3 paddles, so if you like to mess with the
adjustments a lot, be sure to take them into the field with you.
73, Ron AC7AC
-Original Message-
I have a KX3 but I did not get the key paddle option. I am
And there's this carrying case that handles the rig and paddle. One still
handles the paddle connected to the rig. Has room for a mic too.
http://w8fgu.home.comcast.net/~w8fgu/kx3case.html
I don't know how it compares in size, cost, etc., to the ones Rose sells.
73, Ron AC7AC
-Original
watts. Indeed,
the big issue is getting a response from halfway around the world when one
wants a call to local emergency services!
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Lynn W. Taylor,
WB6UUT
Sent
Blaise Pascal once began a letter with:
I am sorry I have had to write you such a long letter, but I did not have
time to write you a short one
He was quite right. Writing something short and concise takes much longer
than writing a lengthy tome.
73, Ron AC7AC
-Original Message
, and customer support is forever noting
that a customer called about this (covered on page 4) and that (on pages
9 and 11) and the other thing (page 15).
73 Ron AC7AC
-Original Message-
I also created a 5 page printed guide and leaving at the station thinking it
would be read. That was dumb
Ken, if you only want batteries to keep the clock running and you otherwise
run off of an external power supply, why not a set of simple alkaline cells?
One set should last years, if not longer!
73 Ron AC7AC
-Original Message-
On Thu, 27 Jun 2013 18:51:22 +, you wrote:
I'm
Just out of curiosity, I put a strain gage on a power cord and checked the
force required to un-mate the APP connector from three pieces of equipment.
One took just 5 lbs.
The second took 7 lbs.
The third took just 5.5 lbs.
I've never had an APP connector disengage accidentally.
73 Ron
The NB icon will flash slowly if the I.F.
blanker setting is too high for the present signal
conditions. If this happens, use a lower setting.
Yeah, it's frustrating when the answers are truncated or the original question
is not included, Hi!
73 Ron AC7AC
-Original Message-
From
you want them.
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Richard Fjeld
Sent: Monday, June 24, 2013 8:18 AM
To: Rip R; elecraft@mailman.qth.net
Subject: Re: [Elecraft] Elecraft and Ten Tec
Roger,
I went
Look at the filter. If it has a collection of individual cans mounted on a
board, it's a 5-pole. Eight pole filters are in a single rectangular can.
You can see photos of them here:
http://www.elecraft.com/manual/K3%20Crystal%20Filter%20Option%20Rev%20A.pdf
See Figure 1 on page 5.
73,Ron
gain antennas are for CW/SSB/DATA over long paths with
horizontal polarization.
73 Ron AC7AC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft
voice
or CW.
73, Ron AC7AC
-Original Message-
K3, KX3, KPA500-FT, KAT500-FT,P3.
On 20/06/2013 7:47 AM, Robert G Strickland rc...@verizon.net wrote:
Sam...
In my *limited* experience with the K3 decoder, I have found that the
quality of the sent cw is a big factor in effective
, the electrical contact pressure
doesn't depend upon the molded plastic like axial type holders do.
I think there's a reason we don't see axial type fuses in automobiles any
longer and I sure don't experience fuse holder failures in my car!
73, Ron AC7AC
-Original Message-
It looks like one
!
73, Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bill K9YEQ
Sent: Monday, June 17, 2013 4:03 PM
Cc: elecraft@mailman.qth.net
Subject: Re: [Elecraft] CAIG DEOXIT or Servisol Super 10
Don,
Nice suggestion. I
/KRX3_Subreceiver_Install-Operate_Manual_Rev_E
.pdf
Pages 25 and 26 show the optional ways to connect the subrx antenna input
either to the KAT3 or to the rear-panel AUX RF input.
Page 43 shows the MENU settings required.
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
Jim is having trouble posting to the reflector so he asked me to forward
this for him.
73 Ron AC7AC
---
From: Jim Harris [mailto:capo...@gmail.com]
Sent: Sunday, June 16, 2013 3:30 PM
To: undisclosed-recipients:
Subject: Fwd: KX3!
Howdy, Group.
My KX3-k (at the time
was a perfect sine
wave and the carrier and opposite sideband suppression were perfect so that
the only RF transmitted was the sideband produced by the audio oscillator.
But, of course, it never is...
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun
indicates a significant change in the antenna, usually not for the best, Hi!
73 Ron AC7AC
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of NZ0T
Sent: Saturday, June 15, 2013 5:16 AM
To: elecraft@mailman.qth.net
Subject: Re
At one time a lot of fellows tried to work all the serial numbers for a
given rig. That was back in the early days when the K2 was the flagship
rig.
I put my s/n's on the list back then because several people asked for them.
I confess that I have not kept it updated though.
73, Ron AC7AC
901 - 1000 of 5130 matches
Mail list logo