Ive been reading up on OSPF for the BSCI test and am confused as to what an
OSPF Host Route is. RFC 2328 refers to OSPF host routes as Hosts attached
directly to routers. Is host route a route to a host? Am I missing
something?
Colin
Message Posted at:
http://www.groupstudy.com/form/read.
Hi all
I just have a query about configuring an isdn backup link to an isp.
I am going to use the backup interface bri0 with the backup delay command
on the serial link.
My question is what routing would i have to add if there is already a
default route going out the serial interface.
Thanks i
Hey Group
I have a Cisco 3005 series concentrator box configured to run between my
Externel router and Checkpoint firewall such that:
INTERNET Router ---> VPN 3005 > Checkpoint--LAN
This is one segment of my network. On another segment of the network I have
a Juniper M20 router w
Hi,
I've finished new, much improved, version of my L2/L3 traceroute
perl script. It can be downloaded from
www.geocities.com/milicsasa/Tools/l2trace/index.html
Happy tracing !
Comments are welcomed.
Regards,
Sasa
CCIE #8635
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&
Dear All,
Suppose there is a PC have 2 IP address configured in single NIC (10.x,
20.x) and connect catalyst 35xx switch that configured with dynamic vlan.
(NOT tagged)
And there are 2 servers with IP 10.x and 20.x connected to the same switch
as well. The server belongs to VLAN 10 and VLAN 20 ba
Hi,
Its nothing..its just that by default ospf advertises the loopback address
as a host route i.e with a mask of /32. This default behaviour can be
changed by giving the command ip ospf network point-to-multipoint under the
interface config mode.
Regards
Message Posted at:
http://www.groupstu
Does anyone know of a command which will show the flavour of GBIC in a
particular slot of a 3550?
Many thanks in advance.
Tim
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=70449&t=70449
--
FAQ, list archives, and subscription
Hi
I was trying to upgrade IOS on 2501 router with 16MB flash and 16MB RAM, new
IOS image requires 16/16 according to Cisco web site. Image size is 15,376
when I upload the image it fails with "memory buffer overflow error". I
tried this on different 25xx models same error on all of them. If an
Considering that your default route is probably pointing to a next-hop of
the other side of the serial or perhaps is pointing to the serial interface
itself, you would still need to tell the router to send traffic out of the
BRI0 in the event that your serial goes down. If you serial interface goe
Hi Tim,
DNWB-008-AS01#show interface gi0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is Gigabit Ethernet, address is 000b.5f82.2cb1 (bia
000b.5f82.2cb1)
Description: Connected to DHAA-005-DR01 Gi3/4
MTU 1500 bytes, BW 100 Kbit, DLY 10 usec,
reliability 255/255, txload 1
A host route is a route with all 1's as the mask... 255.255.255.255
JR
--
Johnny Routin
)?)
-
""Colin Weiner"" wrote in message
news:[EMAIL PROTECTED]
> Ive been reading up on OSPF for the BSCI test and am confused as to what
an
> OSPF Host Route is. RFC 2328 refers to OSPF host
If you mean async ports...no 16 is it at least as far as the 2500 series
goes.
Mitch
- Original Message -
From: "Brian W."
To:
Sent: Monday, June 09, 2003 11:58 PM
Subject: console server ports [7:70438]
> Got a friend building a lab, and well after hes done with servers and
> routers
I tried another version, but occurs the same error message:
R2#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-JS-L), Experimental Version
12.0(20011017:155337) [rraszuk
-New_reorg_oct17 110]
2#sh flash
System flash directory:
File Length Name/status
1 12
Hey Gang has anyone taken the 607 test? If so what are the best books to
study with? My CCNA runs out in a few months so it's back to the books.
Thanks,
Steve
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=70459&t=70459
--
FA
Off Topic:
Does anyone know if you can monitor the % usage by IP address/User or by
download type (ie .mp3) with the PDM .. Or does anyone know of any software
that would do this ??? Does WebSense ???
Kind regards
Paul ...
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=7
Hi all,
I have an issue on a 7200 where it appears that I am running out of memory
although none of the show outputs that I have seen tell me that. When I try
to issue the "show run" nothing happens, I get no output. If I try to copy
start run it gives me the following error:
Router#sh run
Ro
Kenan Ahmed Siddiqi wrote:
>
> Thank You very much Marc but my problem is that I am not
> running any routing protocols. Otherwise I had in mind to use
> floating static routes with Routing Protocols but the problem
> again boils down to this that how can I do it without using any
> routing protoc
Lamy Alexandre wrote:
>
> Hello, You think that it is useful for the CCNP or the CCIE a
> router 7505 with:
Uh, yes, you could use a 7505 in your lab for studying for CCNP and CCIE.
Consider yourself lucky!?
On the other hand, does it only do OC3? That might be hard to use in a lab.
What would y
I have setup AAA on a router which has a primary serial line and a ISDN
backup line.When the primary line goes down the back line does not
authenticate locally at the HQ router.When I take AAA off then it works
fine.If I modify the authentication for login to local then it deletes the
first lin
I've been on the Wave Tech bootcamps.
Both for Cisco and Microsoft, only one instructor showed any 'real-world'
knowledge and could answer confidently questions which were 'off-track'.
This wasn't particularly a problem for me, as I viewed the course as
revision of what I already knew, and was the
yeah the pm2e-30 would work, but I bet he wants to stay cisco, thanx for the
other info.
Bri
- Original Message -
From: "Daniel Cotts"
To: "'Brian W.'" ;
Sent: Tuesday, June 10, 2003 7:44 AM
Subject: RE: console server ports [7:70438]
> If he wants more ports in Cisco gear I beli
outta curiosity, whats the routing protocol and topology? And is your isdn
configured with floating static routes?
and which interface is showing up,up?
I've got a building connected with two wireless links and load balanced with
EIGRP. If one link goes down the other one takes all the traffi
Hi Gary
I attended the NetGun Academy courses last year in preparation for the
lab, and I found the courses to be extremely helpful. There are 6
courses, held over a period of 6 months, and they take you through the
basics os each topic in turn, building up towards the end of each week
into more
Kudos to Craig for a well thought out and written response. This is what
I wanted to
say but my temper got the better of me.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of
Craig Columbus
Sent: Monday, June 09, 2003 5:19 PM
To: [EMAIL PROTECTED]
Subject: RE:
Mark E. Hayes wrote:
>
> I don't know why I am doing this but I am... As far as trading
> in
> numbers goes-
> It doesn't make a difference to me if I am #1100 or #11000. I
> am only a
> CCNA now and
> working on my NP. I feel the reason for the headhunters and HR
> types to
> value a lower numb
1. Attacking his motives and attacking his character are mutually exclusive
endeavors. I attack his motive of defaming the certification process itself
in a series of different topics. I have not criticized any such commentary
that balances all facts, but NRF's overall commentary does no such thi
**
This email and any files transmitted with it are confidential and
intended solely for the use of the individual or entity to whom they
are addressed. If you have received this email in error please notify
the [EMAIL PROTECTED]
Few months is enough time to get your CCNP, depending where you stand with
understanding the technology and hands on.
Don't waste your time with CCNA.
Just my 2 cents.
Jim
-Original Message-
From: Steve Smith [mailto:[EMAIL PROTECTED]
Sent: Tuesday, June 10, 2003 11:12 AM
To: [EMAIL PR
Thanks for everyones assistance. It turned out that this was a known issue
on this release but it was undocumented. We upgraded and all is well.
Thanks,
Mario Puras
SoluNet Technical Support
Mailto: [EMAIL PROTECTED]
Direct: (321) 309-1410
888.449.5766 (USA) / 888.SOLUNET (Canada)
--
If he wants more ports in Cisco gear I believe that he will have to go with
octopus cables. Think NM-async modules for 2600/3600 series. I know 32 port
modules exist.
Several years ago I bought a 10' octal cable from Robert Lowery
[EMAIL PROTECTED] The extra length might help. I don't know if Bob i
Hi,
Can you post the out of 'sh proc mem'?
Thanks,
_
Jim Walker
Network Engineer
(617) 732-8803
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
Sent: Tuesday, June 10, 2003 11:29 AM
To: [EMAIL PROTECTED]
Subject: No output
ack on my previous reply, saw it was for bootflash after sending..
Brian
The path to a desireable destination
is often more difficult than the path to stay where you are.
On Tue, 10 Jun 2003, [EMAIL PROTECTED] wrote:
> Hi all,
>
> I have an issue on a 7200 where it appears that I am ru
Looks like he has two FastEthernet interfaces. If so, he can do Etherchannel
to a switch. He can always remove the ATM Port Adapter and install one with
different interfaces. PAs are still pricey. Others can comment - but I think
the posip card uses an entire VIP2-50. He might be able to remove the
What do you see in your log? How about a sh mem? If it is a memory
problem it is not the lack of flash that would cause this. If your not
on the console trying doing as a "term mon" and reissue the sh runn and
see if your getting errors.
Dave
[EMAIL PROTECTED] wrote:
> Hi all,
>
> I hav
Hi,
Yesterday I passed the CCNP - Remote Access. It was
more difficult than I had thought. Makes me wonder about
the SUPPORT, which will be my last. Of course, I don't
expect to get a job, but it is fun to learn. Then I can focus on
Cisco IP Telephony which is my real inte
Is that output from a 3550? I know the command is the same on most Cisco
gear, but my 3550 doesn't show whether it's SX or LX. It shows everything
else, though.
Robert
""Scott Chau"" wrote in message
news:[EMAIL PROTECTED]
> Hi Tim,
>
> DNWB-008-AS01#show interface gi0/1
> GigabitEthernet0/1 i
[NRF] In this thread, I have attacked what has happened to the CCIE lately.
Not
the CCIE in general, just what has happened to it lately. This is a
[JN] Your overall approach has a pattern to it, and your response ironically
reenforces the notion. The "number of CCIE" thread merely complements
this is an experimental image.
> IOS (tm) 2500 Software (C2500-JS-L), Experimental Version
so this trace can not be decoded like this..
the DE of the image should be contacted..
> %Software-forced reload
regards
devvv
- Original Message -
From: "alaerte Vidali"
To:
Sent: Tuesday, Ju
Hi I have a question here:
If i have 2 Routers and they are connected to the serial connection...
and the ethernet and the ISDN interfaces allso has a IP address.
AND THE ISDN LINE IS CONFUGRED AS BACKUP FOR THE SERIAL LINE.
(So is in standby mode (down))and all of the 3 interfaces have different
I am trying to configure a 2600 router. I have two problems:
1. I issued the default route command
ip route 0.0.0.0 0.0.0.0 x.x.x.x
I can see this under ip classless in "sh run"
However, when I do a "sh ip route", it does not appear there and in fact
says:
Gateway of last resort is not set
2.
What's the general opinion/experience/wisdom regaridng the writing off of
home lab gear costs from one's taxes if the only thing done with this gear
is to study for certifications to further one's career? I say "only". I've
also used this gear to test config's for work as we have no test network
ge
Dear Ms. Priscilla
Thanks alot for your answer but the problem still remains there. The
explanation is as under:-
>I don't think you have to be running a routing protocol to use >Dialer
Watch. "Routing protocol independentStatic routes or dynamic >routing
protocols, such as Interior Gateway Routi
Anil Gupte 6/10/03 4:25:10 PM >>>
>I am trying to configure a 2600 router. I have two problems:
>
>1. I issued the default route command
>ip route 0.0.0.0 0.0.0.0 x.x.x.x
>
>I can see this under ip classless in "sh run"
>
>However, when I do a "sh ip route", it does not appear there and in fa
You can pass one test, only the BSCI or BCRAN test, and retain you CCNA
status (for another 3 years) until you can test for the rest.
You don't need to retest for the CCNA at all.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of
Walker, James, IS
Sent: Tuesda
At 9:46 PM + 6/10/03, Anil Gupte wrote:
>I am trying to configure a 2600 router. I have two problems:
>
>1. I issued the default route command
>ip route 0.0.0.0 0.0.0.0 x.x.x.x
>
>I can see this under ip classless in "sh run"
Is x.x.x.x a reachable address through the routing table?
>
>Howev
Do you have a route to x.x.x.x? If your router does not have a route to
x.x.x.x it will not install the static route in the routing table since the
next hop is unreachable. As far as RIP goes you are seeing the correct
behavior. Remember that RIP is classful.
Brian Dennis, CCIE #2210 (R&S/ISP-Dial
comments inline:
- Original Message -
From: "Anil Gupte"
To:
Sent: Tuesday, June 10, 2003 11:46 PM
Subject: Simple config issues [7:70482]
> I am trying to configure a 2600 router. I have two problems:
>
> 1. I issued the default route command
> ip route 0.0.0.0 0.0.0.0 x.x.x.x
it dep
comments inline:
- Original Message -
From: "Iwan Hoogendoorn"
To:
Sent: Tuesday, June 10, 2003 11:20 PM
Subject: RIP updates trough a serial and ISDN connection [7:70480]
> Hi I have a question here:
>
> If i have 2 Routers and they are connected to the serial connection...
> and the
Hi Group,
I need to buy an updated documentation cd that contains Catalyst 3550
documentations. If any one can sell me one please let me know.
Thanks
John Tafasi
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=70490&t=70490
--
gateway of last resort is not the same as default gateway ciscowise, on the
router where you entered the ip route statement, show ip route doesnt list
an all zeros route??
Bri
- Original Message -
From: "Anil Gupte"
To:
Sent: Tuesday, June 10, 2003 2:46 PM
Subject: Simple config is
If you are planning to take the CCNP 640-605 BCRAN exam anytime soon, I
have completed my review of the exam and invite you to take a look.
http://tcpmag.com/Exams/article.asp?EditorialsID=74
Good luck!
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=70491&t=70491
Best Documentation CD you can get updated quite regularly.
http://www.cisco.com/univercd/home/home.htm
""John Tafasi"" wrote in message
news:[EMAIL PROTECTED]
> Hi Group,
>
> I need to buy an updated documentation cd that contains Catalyst 3550
> documentations. If any one can sell me one plea
Best Documentation CD you can get updated quite regularly.
""John Tafasi"" wrote in message
news:[EMAIL PROTECTED]
> Hi Group,
>
> I need to buy an updated documentation cd that contains Catalyst 3550
> documentations. If any one can sell me one please let me know.
>
>
> Thanks
> John Tafasi
Hi,
which commands do you use to load the IOS into the router? From
IOS or ROM Monitor? Please email me a complete log.
With kind regards
Jens Neelsen
--- Alex wrote:
> Hi
>
> I was trying to upgrade IOS on 2501 router with 16MB flash and
> 16MB RAM, new
> IOS image requires 16/16 according to
Kenan Ahmed Siddiqi wrote:
>
> Dear Ms. Priscilla
> Thanks alot for your answer but the problem still remains
> there. The explanation is as under:-
>
> >I don't think you have to be running a routing protocol to use
> >Dialer Watch. "Routing protocol independentStatic routes or
> dynamic >routi
55 matches
Mail list logo
