What does a Dial Shelf Interconnect card do on a 7200 router? [7:15831]
Please reply privately. Thanks. -Frank Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15831t=15831 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
CCIE Written [7:15832]
Hi all, I have CCNP, ATM and VoIP certified and now preparing for CCIE. I only have two weeks to go besides I need to work. Can anyone suggest the most important material to review before going for the written exam. Behind me is: 1) Carlow's 2nd edition 2) Free Token Ring paper from CCprep.com 3) CCNP, ATM and VoIP Cisco press books 4) Routing TCP/IP Vol. I Is one Carlow's book + Token Ring paper enough for the exam.? Is Carlow's book on non-IP material enough to handle all non-IP question in written? Please help if you have achieved the written test. Thx. Kenneth Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15832t=15832 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
news group [7:15833]
hi, can any body can tell a good news group for unix and solaris thanxs kaushalender Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15833t=15833 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Access Lists On Routers [7:15830]
Hi, This depends on what you are trying to acheive but under most circumstances one would tend to block the traffic at the entry point. For example, if it was traffic from the WAN the block it coming in on the WAN interface. If however you wanted to see the traffic in the router for some reason then you might apply the same access-list on the ethernet going out. So it really depends on what the needs of your access-lists are. Usually on a 1 WAN port to 1 Ethernet port incoming from the WAN do it as INCOMING on the WAN port. Just some long winded thoughts from an older guy. Teunis, Hobart, Tasmania Australia On Monday, August 13, 2001 at 02:25:48 AM, yusuf ujjainwala wrote: I am a network engineer and have been assigned a task of implementing access lists on our routers. I have decided on implementing extended access lists permitting specific ports and restricting the other unwanted ports,but I am not sure as to where I should apply the access lists ,on the ethernet or serial interfaces ,and whether inbound or outbound access lists should be applied. Can somebody help me . -- www.tasmail.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15834t=15830 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
catalyst 2900 XL got reset [7:15835]
hi i was trying to access the 2900XL series switch through hyperterminal and strange thing happened ,it got reset by it on.did this happened with somebody else also ,just curious to know.what could be the reason Regards Arun Sharma Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15835t=15835 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CCIE Written [7:15832]
consider what happens to PDU's as they traverse networks and media of various kinds. device--medium--device--medium--device--medium--device device = server, workstation, router, switch, hub, repeater, etc medium = ethernet, token ring, frame-relay, point-to-point, x.25, etc mix and match all you want. have some fun. what happens to a PDU as it goes from one end to the other? a good refresher in the basics of networking, which is something all of us in this business do need continually drilled into our heads. best wishes on your test Chuck -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Kenneth Yeung Sent: Sunday, August 12, 2001 11:54 PM To: [EMAIL PROTECTED] Subject: CCIE Written [7:15832] Hi all, I have CCNP, ATM and VoIP certified and now preparing for CCIE. I only have two weeks to go besides I need to work. Can anyone suggest the most important material to review before going for the written exam. Behind me is: 1) Carlow's 2nd edition 2) Free Token Ring paper from CCprep.com 3) CCNP, ATM and VoIP Cisco press books 4) Routing TCP/IP Vol. I Is one Carlow's book + Token Ring paper enough for the exam.? Is Carlow's book on non-IP material enough to handle all non-IP question in written? Please help if you have achieved the written test. Thx. Kenneth Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15836t=15832 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CCIE Written [7:15832]
I heard that the CCIE written like CID. Is it true? Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15837t=15832 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: FW: CAN SOME ONE NO EXPERIMENT CAN PASS CCNP [7:15778]
The answer is YES and DEFINITELY. Remember to read the 4 cisco press books for CCNP. If you understand and remember these 4 books, you can be certified even without experiment/experience. Because you are not ask to build a complete network. You just need to demonstrate that you really understand the networking concept and protocols. Good Luck..and start now. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15838t=15778 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CAN SOME ONE NO EXPERMIENT CAN PASS CCNP [7:15717]
This is more like a chicken egg discussion. Which was first chicken or egg? Should you have certification first or experience? Certification is possible without experience but my question is how do you get experience without certification in this competitive market and IT job freeze (there are always few exceptions to rule). HR and technical managers will not even talk to you without some sort of certifications. It's true that initially the person who have no experience and has only certifications will not be as productive but it's only matter of time when this person in real world starts picking up stuff fast. ---Original Message--- From: [EMAIL PROTECTED] Date: Sunday, August 12, 2001 07:13:13 PM To: [EMAIL PROTECTED] Subject: RE: CAN SOME ONE NO EXPERMIENT CAN PASS CCNP [7:15717] a newly minted CCNP could bluff their way into a job but isn't it the hiring mangers responsibility to say if they keep the job after they display a lack of expertise. I think the Cisco cert. excluding the CCIE validate experience for some and provide a foundation to build on for others. just my 2 cents. -Original Message- From: ext Dennis Bailey [mailto:[EMAIL PROTECTED]] Sent: Sunday, August 12, 2001 10:53 AM To: [EMAIL PROTECTED] Subject: Re: CAN SOME ONE NO EXPERMIENT CAN PASS CCNP [7:15717] The point of certifications is (was) to validate one's experience and/or knowledge. The CCNA has already gone the way of the MCSE and CNE certs. CCNP is on its way as well. Memorizing material for a few simple tests means squat in the real world. You may impress the HR screener into getting to the interview with the hiring manager. You may even be able to bluff your way into a job offer. Then you have to be able to actually do the work or explain to the boss why he needs to pay for someone who knows what they are doing to come in and fix the problem or worse, why he has people sitting around on the payroll twiddling their thumbs while his freshly minted CCNP tries to figure out which command will fix the network which is down. Gareth Hinton wrote in message news:[EMAIL PROTECTED]... Why bother studying anything at school/college. It's not real world experience. If I was interviewing someone who said I didn't bother studying for any Cisco certifications because they are not real world experience, they'd be back out into the real world without finishing their coffee. I believe that any relevant knowledge can fill gaps in the future. Its a good base to start from. Gaz Dennis Bailey wrote in message news:[EMAIL PROTECTED]... Yes but why What would you do with it? PHIMHONGKONG wrote in message news:[EMAIL PROTECTED]... Hi i have a question I have no working experiment but i have some router to study at home Do i have a chance to pass ccnp? Thanks Give me a honest answer Thanks com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15840t=15717 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CCIE Written [7:15832]
I sure had that impression. similar approach to protocol behaviour. similar feel of the questions. if you passed the CID, and if you have covered the additional material as several here have recommended, you should be OK. best wishes Chuck -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Kenneth Yeung Sent: Monday, August 13, 2001 1:08 AM To: [EMAIL PROTECTED] Subject: RE: CCIE Written [7:15832] I heard that the CCIE written like CID. Is it true? Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15841t=15832 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
FW: SECURITY WIRE DIGEST, VOL. 3, NO. 63, AUGUST 1 [7:15842]
This one hit my in-box tonight. I'm forwarding the information about the crack of the wired equivalent privacy ( WEP ) This is far more serious than the announcement by the Berkeley folks a few weeks ago. I look forward to Cisco's response. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] Sent: Sunday, August 12, 2001 11:50 PM Subject: SECURITY WIRE DIGEST, VOL. 3, NO. 63, AUGUST 13, 2001 Security Wire Digest is an e-mail newsletter brought to you on Mondays and Thursdays by Information Security magazine. SWD is written, edited and produced by: Shawna McAlearney, editor, mailto:[EMAIL PROTECTED] Andy Briney, mailto:[EMAIL PROTECTED] Anne Saita, mailto:[EMAIL PROTECTED] Christine St. Pierre, mailto:[EMAIL PROTECTED] Lawrence M. Walsh, mailto:[EMAIL PROTECTED] 1. INFOSEC NEWS *POP GOES THE WEP PROTOCOL By Shawna McAlearney Any remaining illusions about the security of 802.11 protocol for wireless local-area networks (WLAN) were dashed last week when ATT Labs released a report describing a devastating new attack that acquires a network key in 15 minutes. Based on the RC4 cipher, the wired-equivalent privacy (WEP) encryption scheme has weaknesses in the key-scheduling algorithm that allows an attacker to retrieve a network's key, gaining full user access in less than 15 minutes, according to the report written by ATT's Adam Stubblefield, John Ioannidis and Avi Rubin. University of Maryland computer scientists earlier this year found a way to sniff cleartext messages containing the name of the network, which is used as a shared secret for authentication in some 802.11 implementations. A similar problem was found in the media access-control addresses used on the WLAN cards, which also broadcast in easy-to-capture cleartext. A third flaw involved an encryption error that allows an attacker to capture plaintext and ciphertext of shared keys and leverage them against WEP's shared-key authentication to join the network. Earlier, researchers at the University of California at Berkeley found a number of ways to intercept and modify wireless transmissions and to access restricted networks. Previous attacks have taken from eight hours to several days to exploit, and resulted in the capture of finite amounts of encrypted data--not the retrieval of the full network key. It's much worse than the Berkley paper, says Chris Wysopal, @stake's director of research and development, also known as Weld Pond. Their attack never recovered the key--only bits and pieces of encrypted data--and it was fairly difficult to do because you captured the data and then had to go and crack it. That's not the case with the new exploit. Another ramification of the new exploit is that it's passive, never giving the user any indication that he is being monitored. In this attack, an attacker never has to actually transmit a packet; he can simply sit on the network and the victim will never even know that he was attacked, says Stubblefield, the ATT Labs intern who created the exploit. So this is a much stronger attack and allows the attacker to completely recover the key, which means that he can send arbitrary data on the network. Though only recently standardized, 802.11 has been incorporated into the Microsoft Windows OS and WLAN components by several companies. It's also widely deployed in corporations, hospitals and other locations. The 802.11 standard is really catching on because it's very cheap and it replaces the need to completely wire the building, says Stubblefield. According to the manufacturer, it comes with its own security, but the fact that it's so easy to completely compromise and undermine the security, means that there are now many, many vulnerable networks out there. In addition to the exploit tool made by ATT Labs, security consultancy @stake also created one to help in its wireless assessment efforts. The problem lies in the key-scheduling algorithm of RC4 and allows almost anyone with a WLAN-enabled laptop to retrieve a network's key in less than 15 minutes, says Wysopal. This is only with the 40-bit key, but the attack scales linearly to 128 bits so it shouldn't take much longer. Security experts recommend installing the WLAN outside the firewall using a VPN in a DMZ with only an access point; changing the key immediately and often; and conducting WLAN audits regularly to ensure there are no rogue connections. Others say the entire network would need to be restructured and IPSec installed on each individual desktop. Mitigation might be doing network-level security on top of the link wire IPSec or doing application-level SSH and using the 802.11 simply as a data link layer for communication and not relying on any security services from that layer, says Rubin, principal researcher at ATT Labs and author of White-Hat Security Arsenal. http://www.cs.rice.edu/~astubble/wep = Security Wire Digest and Information Security magazine
RE: Access Lists On Routers [7:15830]
I would agree. It all depends on your network and what you are trying to achieve with the Acl's. D'Wayne Saunders Network Admin Ph:08 89507742 Fax:08 89521112 Mobile: www.lasseters.com.au World's First Government Licensed and Regulated Online Casino... *** This email message (and attachments) may contain information that is confidential to Lasseters Online. If you are not the intended recipient you cannot use, distribute or copy the message or attachments. In such a case, please notify the sender by return email immediately and erase all copies of the message and attachments. Opinions, conclusions and other information in this message and attachments that do not relate to the official business of Lasseters Online are neither given nor endorsed by it. *** -Original Message- From: Tony van Ree [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 16:41 To: [EMAIL PROTECTED] Subject: Re: Access Lists On Routers [7:15830] Hi, This depends on what you are trying to acheive but under most circumstances one would tend to block the traffic at the entry point. For example, if it was traffic from the WAN the block it coming in on the WAN interface. If however you wanted to see the traffic in the router for some reason then you might apply the same access-list on the ethernet going out. So it really depends on what the needs of your access-lists are. Usually on a 1 WAN port to 1 Ethernet port incoming from the WAN do it as INCOMING on the WAN port. Just some long winded thoughts from an older guy. Teunis, Hobart, Tasmania Australia On Monday, August 13, 2001 at 02:25:48 AM, yusuf ujjainwala wrote: I am a network engineer and have been assigned a task of implementing access lists on our routers. I have decided on implementing extended access lists permitting specific ports and restricting the other unwanted ports,but I am not sure as to where I should apply the access lists ,on the ethernet or serial interfaces ,and whether inbound or outbound access lists should be applied. Can somebody help me . -- www.tasmail.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15839t=15830 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Off Topic: Routing Protocols and OSI layers [7:15755]
It was posted: System management protocols such as SNMP definitely are application layer. Routing protocols are layer management protocols of the same layer as the addresses for which they are computing routes. OSPF, ISIS, etc., are layer 3 management protocols. 802.1d is a layer 2 management protocol. This is absolutely unambiguous if one reads the correct ISO documents. And I would add: Or, if you read Cisco's own Networking Academy Program curriculum, which says the same thing. :-[)] Mark A. Morenz, MS Ed, CCNA, CCAI Regional CCNA Director, CNAP Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15845t=15755 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Len Lee/CHI/NTRS is out of the office. [7:15846]
I will be out of the office starting 08/13/2001 and will not return until 08/17/2001. I will respond to your message when I return. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15846t=15846 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
callback on 2600 [7:15849]
Hi guys Please assist in the configuration of callback on the 2600. For some reason, it does not work. Underneath please find a copy of my config. Your assistance will be highly appreciated. 2600#sh run Building configuration... Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname 2600 ! aaa new-model aaa authentication login default local aaa authentication login vty local aaa authentication login dialin local aaa authentication ppp default local enable secret 5 $1$2sLc$CE4MJiDYrS4jccjjLCxzh0 enable password networks ! username cisco password 0 test username qwerty password 0 123456 username sirpald callback-dialstring password 0 polo modem country microcom_hdms south-africa ip subnet-zero ip address-pool local ! ! ! ! ! ! ! interface Ethernet0/0 ip address 172.20.1.3 255.255.255.0 ip broadcast-address 255.255.255.0 no ip directed-broadcast ! interface Group-Async1 ip unnumbered Ethernet0/0 ip broadcast-address 255.255.255.0 no ip directed-broadcast encapsulation ppp async mode dedicated peer default ip address pool default no fair-queue ppp callback accept ppp authentication pap chap group-range 33 48 ! interface Dialer1 ip unnumbered Ethernet0/0 no ip directed-broadcast encapsulation ppp dialer in-band dialer-group 1 ppp callback accept ppp authentication pap chap ppp multilink ! ip local pool default 172.20.1.31 172.20.1.46 ip default-gateway 172.20.1.1 ip classless ip route 0.0.0.0 0.0.0.0 172.20.1.1 ip http server ip http access-class 15 ! dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit banner motd ^CC Unauthorised Access will be Prosecuted ^C ! line con 0 transport input none line 33 48 autoselect ppp script callback mod modem InOut modem autoconfigure discovery transport input all flowcontrol hardware line aux 0 line vty 0 4 password mesh ! no scheduler allocate end ___ http://www.webmail.co.za the South-African free email service Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15849t=15849 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
PIX failover!! [7:15848]
Dear All, Sorry for the stupid question but I want to confirm it. I have to configure my PIX 515UR bundle... How can I know the primary unit from the secondary unit?? Is that from the failover cable only OR there is an other thing marked the unit as primary or secondary??? Please advice me soon,,, Regards,,, Magdy Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15848t=15848 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: catalyst 2900 XL got reset [7:15835]
yes, actually, this happened to me w/ out servers switch :( in production. i never got a clear answer as to why this happened, but i'm never plugging into a 2900 console port in production w/ a windows box again. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15850t=15835 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Static routes [7:15851]
Can anyone tell me if you are able to use a loopback address in a static route. For example ip route x.x.x.x y.y.y.y 196.8.87.17 x.x.x.x y.y.y.y being the loopback address. Thanks Mike __ Disclaimer and confidentiality note Everything in this e-mail and any attachments relating to the official business of Standard Bank Investment Corporation (Stanbic) is proprietary to the company. It is confidential, legally privileged and protected by law.\ Stanbic does not own and endorse any other content. Views and opinions are those of the sender unless clearly stated as being that of Stanbic. The person addressed in the e-mail is the sole authorised recipient. Please notify the sender immediately if it has unintentionally reached you and do not read, disclose or use the content in any way. Stanbic can not assure that the integrity of this communication has been maintained nor that it is free of errors, virus, interception or interference. __ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15851t=15851 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Static routes [7:15851]
Sure, except that you might defeat the purpose of having a loopback address by doing this. Say you've got a scenario where you have two routers connected by three separate connections: /-\ O---O \_/ If you specify the next hop of the loopback to be just *one* of the interfaces on the other router, then the loopback will be inaccessable if that one interface on the other router goes down. If you're using static routes, be sure to include all the different paths you can take to get to the other router - which may be complex enough to warrant just going to RIP or OSPF. ;-) BJ -Original Message- From: Hawthorne, Mike MM [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 8:09 AM To: [EMAIL PROTECTED] Subject: Static routes [7:15851] Can anyone tell me if you are able to use a loopback address in a static route. For example ip route x.x.x.x y.y.y.y 196.8.87.17 x.x.x.x y.y.y.y being the loopback address. Thanks Mike Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15852t=15851 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Static routes [7:15851]
Yes, you can. - Original Message - From: Hawthorne, Mike MM To: Sent: Monday, 13 August, 2001 14:08 Subject: Static routes [7:15851] Can anyone tell me if you are able to use a loopback address in a static route. For example ip route x.x.x.x y.y.y.y 196.8.87.17 x.x.x.x y.y.y.y being the loopback address. Thanks Mike __ Disclaimer and confidentiality note Everything in this e-mail and any attachments relating to the official business of Standard Bank Investment Corporation (Stanbic) is proprietary to the company. It is confidential, legally privileged and protected by law.\ Stanbic does not own and endorse any other content. Views and opinions are those of the sender unless clearly stated as being that of Stanbic. The person addressed in the e-mail is the sole authorised recipient. Please notify the sender immediately if it has unintentionally reached you and do not read, disclose or use the content in any way. Stanbic can not assure that the integrity of this communication has been maintained nor that it is free of errors, virus, interception or interference. __ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15853t=15851 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: 2501 router... [7:14553]
Hey there its Mr Mellow. I wasn't talking to you I thought you only got fired up when provoked. O, and mellow, that spelling thing bounces of me and sticks to you cause I rubber and you are glue. hillarious - Original Message - From: nrf To: Sent: Friday, August 10, 2001 2:34 PM Subject: Re: 2501 router... [7:14553] Once again, wonderful brilliant commentary from the esteemed Mr. Johnson. We are so graced by the presence of you and your brilliant commentary. Why is it exactly that you feel the need to get off by biting other people's heads off (and doing so by using 2nd-grade level spelling skills, if you remember our last exchange)? When are you going to wake up and realize that you, sir, are an ass, always have been an ass, and always will be an ass? Donald B Johnson jr wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... If you have been here a year and don't know: a. how to research on cco b. how to check the archives c. how to connect to console d. how to change password e. that you should read a book you purchased that probably has both answers f. that there is a ccna group g. that this is helpful h. that I'm a smart a** then are we to believe that you are going to crimp a roll cable. Or are you going to build that by taking the plastic off. - Original Message - From: Schmelzer Tim L Contr 12 CPTS/FMS To: Sent: Wednesday, August 01, 2001 1:30 PM Subject: 2501 router... [7:14553] Greetings all. I'm kinda new to this game, but have been lurking here for about a year now. I have just been given a 2501 series router and now have a few questions. How do I build a console cable to connect to it? How do I clear any passwords that will be present? Is there somewhere that I can get scenarios / lab situations to practice on this router? I have purchased Todd Lammle's CCNA book and look forward to using this router with my studies. Thanks in advance for any answers, T. Schmelzer Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15854t=14553 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Friday Follies - IP NAT behaviour [7:15822]
Sounds to me like he may have config'd NAT to forward all traffic to his web server. Mark -Original Message- From: Brian [SMTP:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 1:46 AM To: [EMAIL PROTECTED] Subject:Re: Friday Follies - IP NAT behaviour [7:15822] why he gets to the server when telnetting to the router, perhaps the router is forwarding more ports than just 80, perhaps 23, perhaps more.. Bri - Original Message - From: Chuck Larrieu To: Sent: Sunday, August 12, 2001 9:06 PM Subject: Friday Follies - IP NAT behaviour [7:15822] so I'm late. so sue me ;- last Friday while I was in the office I got to chatting with one of the other SE's. He had a problem with his home setup and wanted some help. It was an interesting enough problem that I thought some of you CCNA's, some of your CCNP candidates, might enjoy taking a crack at it. this person has a DSL connection to the internet. He has an single assigned IP address. He is using a Cisco router as his firewall, in this fashion: internet---DSL_router--Cisco_router--web_server E0 E1 life is good. then he starts to fool around with NAT. He puts a private IP on his web server, and he runs NAT on the Cisco router. Again, life is good. folks can reach his web server from the net. but now he wants to telnet from the net ( i.e. from work ) into the Cisco router.. He cannot do so. instead he hits his web server, where telnet is not running as a service. so he disables NAT. he configures policy routing, and places the policy statement on the correct interface. tries to telnet into the cisco router. He can do so. however, now he cannot reach the web server from the net. if he enables the http server on the Cisco router, he gets the Cisco router login screen from his browser. now the question is, why? that is, what is the reason that the two situations occur? with NAT enabled, he cannot telnet to the router. with NAT disabled, he cannot browse the web server, even with policy routing in place. you may assume that all configurations are correct, both for NAT and for policy routing. At least that's what the two CCIE's who joined the discussion told us ;- answers late Monday. Chuck Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15855t=15822 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Bad experiences with IQSale aka Grandstore ..... [7:15756]
Agreed, and contact your States Attorney Generals office if they are in a different state you may also want to contact both your and the originating states AG's office. Like Jon said these guys like to mobilize. Worked for me on a third party car warrenty. You may also think about small claims court in your local area, and have a judgement entered. - Original Message - From: Jon Krabbenschmidt To: Sent: Saturday, August 11, 2001 10:18 AM Subject: RE: Bad experiences with IQSale aka Grandstore . [7:15756] I would also contact the District Attorney's Office in the area that they operate. If you have never contacted a DA's office you may be surprised at how responsive and aggressive they are. Jon -Original Message- From: Jason [mailto:[EMAIL PROTECTED]] Sent: Saturday, August 11, 2001 8:13 AM To: [EMAIL PROTECTED] Subject: Bad experiences with IQSale aka Grandstore . [7:15756] After talking to a couple of other people, I've found that I'm not the only one having problem getting refund from IQSale aka Grandstore , with a couple of other names For myself, I was promised a refund way back in late May and after numerous emails, on 4th July, promised to get back to me with details on the refund and till today is waiting for the cheque. My emails to them after 4th July was ignored. I'm planning to set up a web pages with testimonies about the problems we have with this company and also, if it has since been resolved, how long it took and the steps he or she has to take before the company would resolve the issue or refund I have filed a complaint with BBB and is considering filing a complaint with USPS for mail fraud as well. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15858t=15756 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: PIX failover!! [7:15848]
Hi, It is the cable only that selects the primary or secondary (it is even written on the cable). You make the configuration on the primary, and this will be sigronized with the secondary. Hope this helps, bye, Magdy H. Ibrahim wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Dear All, Sorry for the stupid question but I want to confirm it. I have to configure my PIX 515UR bundle... How can I know the primary unit from the secondary unit?? Is that from the failover cable only OR there is an other thing marked the unit as primary or secondary??? Please advice me soon,,, Regards,,, Magdy Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15856t=15848 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
BGP and NAT [7:15859]
Hi, Simply say, suppose configuring BGP between Router A and B. Router A makes a neighbor reference to the connected interface of router B. I would like to know can I configure ip nat outside on that interface on router B? Since once I configure it, after the hold time period, the BGP connection is lost and stay in Active state. Thanks a lot Regards, mak Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15859t=15859 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
quality of service for h.323 [7:15857]
Hi there does anyone know which queing implementation is better for video over ip in a atm enviorment Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15857t=15857 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CCIE Written [7:15832]
I took written today and passed, you should do fine with your material Regards Rob CCNP (CCIE one day) -Original Message- From: Kenneth Yeung [SMTP:[EMAIL PROTECTED]] Sent: 13 August 2001 07:54 To: [EMAIL PROTECTED] Subject: CCIE Written [7:15832] Hi all, I have CCNP, ATM and VoIP certified and now preparing for CCIE. I only have two weeks to go besides I need to work. Can anyone suggest the most important material to review before going for the written exam. Behind me is: 1) Carlow's 2nd edition 2) Free Token Ring paper from CCprep.com 3) CCNP, ATM and VoIP Cisco press books 4) Routing TCP/IP Vol. I Is one Carlow's book + Token Ring paper enough for the exam.? Is Carlow's book on non-IP material enough to handle all non-IP question in written? Please help if you have achieved the written test. Thx. Kenneth Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15860t=15832 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
e0 on 4000-m router [7:15861]
I have a Cisco 4000 with 2 serial, 1 token ring and 2 ethernet interface. However, when a show interfaces command is executed, there is only one ethernet interface shown. On the back of the router where the ethernet ports are, one is a typical 10baseT, RJ-45 connection, but the other is AUI which I do not have a transceiver for; I just have a CAT5 cable from the 10baseT connector going to my switch. When I do a show interfaces command, ethernet 0 is up, but the protocol is down. On my swith I do not see any activity lights for that port, so I am thinking that my e0 is actually the AUI port. How do I use the 10baseT interface? -- Vik Evans - MCSE, CCNA, CCDA [EMAIL PROTECTED] Cell: (602) 677-8214 Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15861t=15861 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Some Study and Preparation Advice [7:15758]
Excellent advice as always Chuck, and if I may be so bold as to add, try it before you ask. You learn more out of your failures than your successes. You also learn how to broaden your scope, which will be necessary for your lab, and I hope that is why we are here. Password recovery is an example; there is always a question on this list about it. Anybody that would tell someone how to recover from an unknown password is not helping the person. You are even stretching it by telling them about CCO in my opinion. By not helping people in this way you set the groundwork for that person learning how to find the answer they need. If this were not an important and needed skill they would not give you a CD when you sit your lab. Again learning what doesn't work is equally important to a successful sit at the lab, reason being that the lab is such a time intensive exercise. So knowing what doesn't work will save time and will prove invaluable in the methodology part of the lab not just the mechanics. I feel that if there weren't such an impetus on time during the lab the first time success rate would jump dramatically, say 10-15%. Also for those who are one-day'ers myself included, I think time will factor in even more. Execution, execution execution..won't be much time to go down the gilded path. - Original Message - From: Chuck Larrieu To: Sent: Saturday, August 11, 2001 8:22 AM Subject: Some Study and Preparation Advice [7:15758] A recommended good practice / good habit all those pursuing certification probably should begin to cultivate: familiarize yourself with the contents of the Cisco technical documents page. as you strive for higher and higher levels of certification, you will find it invaluable to have read as much of this stuff as you can, and to know how and where to find things about which you are unsure. the design guides, the configuration guide, and the command references are all there, and should be the first place you look for answers. admittedly, this can be difficult on dial up lines. DSL or cable modem is a great help. Another help is access to a laser printer, so you can print out a lot of this stuff. makes general reading a lot easier. one person with whom I correspond prints things out on paper with pre-punched holes, making it easier to organize things into binders. so bookmark the following link: http://www.cisco.com/univercd/home/home.htm it will serve you well in your certification and professional pursuits. Chuck Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15862t=15758 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: e0 on 4000-m router [7:15861]
Hi If the NP has one RJ-45 and one AUI then you do not have 2 ethernet ports, you have one. The NP-1E has one RJ45 and one AUI, the NP-2E has two each. You use either the AUI or the RJ45, but not both at the same time. To use one or the other use the interface command media and follow the options available. BTW, you may need a cross over cable to your switch too. HTH -- John Hardman CCNP MCSE Vik wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... I have a Cisco 4000 with 2 serial, 1 token ring and 2 ethernet interface. However, when a show interfaces command is executed, there is only one ethernet interface shown. On the back of the router where the ethernet ports are, one is a typical 10baseT, RJ-45 connection, but the other is AUI which I do not have a transceiver for; I just have a CAT5 cable from the 10baseT connector going to my switch. When I do a show interfaces command, ethernet 0 is up, but the protocol is down. On my swith I do not see any activity lights for that port, so I am thinking that my e0 is actually the AUI port. How do I use the 10baseT interface? -- Vik Evans - MCSE, CCNA, CCDA [EMAIL PROTECTED] Cell: (602) 677-8214 Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15863t=15861 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: e0 on 4000-m router [7:15861]
In a message dated 8/13/01 8:33:59 AM Central Daylight Time, [EMAIL PROTECTED] writes: Installing Network Processor Modules in the Cisco 4000 Series HTH, Rob H. I have a Cisco 4000 with 2 serial, 1 token ring and 2 ethernet interface. However, when a show interfaces command is executed, there is only one ethernet interface shown. On the back of the router where the ethernet ports are, one is a typical 10baseT, RJ-45 connection, but the other is AUI which I do not have a transceiver for; I just have a CAT5 cable from the 10baseT connector going to my switch. When I do a show interfaces command, ethernet 0 is up, but the protocol is down. On my swith I do not see any activity lights for that port, so I am thinking that my e0 is actually the AUI port. How do I use the 10baseT interface? -- Vik Evans - MCSE, CCNA, CCDA [EMAIL PROTECTED] Cell: (602) 677-8214 Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15865t=15861 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
who has purchased Boson test #3 for written CCIE? [7:15864]
how is Boson test 3 i am thinking of buying it Thanks Felix da Cat Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15864t=15864 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: e0 on 4000-m router [7:15861]
It is only a single port ethernet... You have a choice of AUI or RJ45.. I do not think the 4000M supports a dual ethernet card.. = Original Message From Vik = I have a Cisco 4000 with 2 serial, 1 token ring and 2 ethernet interface. However, when a show interfaces command is executed, there is only one ethernet interface shown. On the back of the router where the ethernet ports are, one is a typical 10baseT, RJ-45 connection, but the other is AUI which I do not have a transceiver for; I just have a CAT5 cable from the 10baseT connector going to my switch. When I do a show interfaces command, ethernet 0 is up, but the protocol is down. On my swith I do not see any activity lights for that port, so I am thinking that my e0 is actually the AUI port. How do I use the 10baseT interface? -- Vik Evans - MCSE, CCNA, CCDA [EMAIL PROTECTED] Cell: (602) 677-8214 Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15866t=15861 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: e0 on 4000-m router [7:15861]
They are the same interface - Original Message - From: Vik To: Sent: Monday, August 13, 2001 6:35 AM Subject: e0 on 4000-m router [7:15861] I have a Cisco 4000 with 2 serial, 1 token ring and 2 ethernet interface. However, when a show interfaces command is executed, there is only one ethernet interface shown. On the back of the router where the ethernet ports are, one is a typical 10baseT, RJ-45 connection, but the other is AUI which I do not have a transceiver for; I just have a CAT5 cable from the 10baseT connector going to my switch. When I do a show interfaces command, ethernet 0 is up, but the protocol is down. On my swith I do not see any activity lights for that port, so I am thinking that my e0 is actually the AUI port. How do I use the 10baseT interface? -- Vik Evans - MCSE, CCNA, CCDA [EMAIL PROTECTED] Cell: (602) 677-8214 Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15868t=15861 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: e0 on 4000-m router [7:15861]
Sounds like a 1 port enet card to me. You have a choice of running either the aui port or the rj-45 port, but not both. I believe you can select between by using the media-type command on the interface. Mark -Original Message- From: Vik [SMTP:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 9:36 AM To: [EMAIL PROTECTED] Subject:e0 on 4000-m router [7:15861] I have a Cisco 4000 with 2 serial, 1 token ring and 2 ethernet interface. However, when a show interfaces command is executed, there is only one ethernet interface shown. On the back of the router where the ethernet ports are, one is a typical 10baseT, RJ-45 connection, but the other is AUI which I do not have a transceiver for; I just have a CAT5 cable from the 10baseT connector going to my switch. When I do a show interfaces command, ethernet 0 is up, but the protocol is down. On my swith I do not see any activity lights for that port, so I am thinking that my e0 is actually the AUI port. How do I use the 10baseT interface? -- Vik Evans - MCSE, CCNA, CCDA [EMAIL PROTECTED] Cell: (602) 677-8214 Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15867t=15861 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
e0 on 4000-m router UPDATE [7:15869]
Figured it out. I had to use the media-type command. -- Vik Evans - MCSE, CCNA, CCDA [EMAIL PROTECTED] Cell: (602) 677-8214 Hm: (480) 633-1888 Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15869t=15869 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: e0 on 4000-m router [7:15861]
Hi The 4000 and 4000M support the NP-1E and NP-2E, the strange part is that the NP-1E is not supported on the 4500 or 4700 series... -- John Hardman CCNP MCSE guyman wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... It is only a single port ethernet... You have a choice of AUI or RJ45.. I do not think the 4000M supports a dual ethernet card.. = Original Message From Vik = I have a Cisco 4000 with 2 serial, 1 token ring and 2 ethernet interface. However, when a show interfaces command is executed, there is only one ethernet interface shown. On the back of the router where the ethernet ports are, one is a typical 10baseT, RJ-45 connection, but the other is AUI which I do not have a transceiver for; I just have a CAT5 cable from the 10baseT connector going to my switch. When I do a show interfaces command, ethernet 0 is up, but the protocol is down. On my swith I do not see any activity lights for that port, so I am thinking that my e0 is actually the AUI port. How do I use the 10baseT interface? -- Vik Evans - MCSE, CCNA, CCDA [EMAIL PROTECTED] Cell: (602) 677-8214 Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15871t=15861 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: VLAN interface remains SHUTDOWN ! ! ! ! ! ! ! [7:15742]
On a 2900XL series catalyst only one vlan interface will be up. The others will be in administratively shutdown state! Gerwin - Original Message - From: Sundar To: Sent: Saturday, August 11, 2001 4:00 PM Subject: Re: VLAN interface remains SHUTDOWN ! ! ! ! ! ! ! [7:15742] I am not sure if you can you assign more than 1 IP address to a switch for management purposes. This is a layer 2 device and you are using an IP address to manage the whole device not the VLANs. Try removing the IP address from one of the VLANs and see if it works. Cheers, Sundar Hamid wrote in message news:[EMAIL PROTECTED]... Hi group, I have a CATALYST 2900XL switch. All the settings sre set to defualt except the hostname, IP address, I have configured some ports to be on VLAN 2. But the problem is that VLAN 2 remains shutdown In the configuration: show int vlan 2 VLAN2 is administratively down, line protocol is down Hardware is CPU Interface, address is 0004.9a99.9d80 (bia 0004.9a99.9d80) Internet address is 192.168.1.254/24 MTU 1500 bytes, BW 1 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA ARP type: ARPA, ARP Timeout 04:00:00 ! interface FastEthernet0/9 switchport multi vlan 1,2 switchport mode multi ! interface FastEthernet0/10 switchport access vlan 2 ! interface VLAN1 ip address 192.168.0.254 255.255.255.0 no ip directed-broadcast no ip route-cache ! interface VLAN2 ip address 192.168.1.254 255.255.255.0 no ip directed-broadcast no ip route-cache shutdown Can anyone tell me what the problem is? Thanx in advance Hamid Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15873t=15742 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: catalyst 1200 [7:15701]
Hi Used one many years (95/96) ago before upgrading to a Cat5000. It is a 8 x 10BaseT, 1 x FDDI DAS/2 x FDDI SAS switch - designed primarily as a FDDI concentrator. This is a CatOS device, but the software I used is of a very low revision of CatOS ( has anyone ever used a catalyst 1200. from what I can tell it uses the catos. are there any differences from the regular 5000s? Im wondering if I can pick one of these up and put it into my lab and spend my money on isdn instead of a fullblown 5000. Ben __ Do You Yahoo!? Send instant messages get email alerts with Yahoo! Messenger. http://im.yahoo.com/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15872t=15701 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
IPSec Latency [7:15874]
Hi All, I was wondering if anyone has any information or sites which talk about how to tweak (if this can be done) IPSec tunnls (via keepalives) from a dial up client to a VPN5008? We have a latency of around 800 milliseconds on a network and we are trying to determine what the maximum delay can be in the network to keep the tunnel up via keepalives. How long can the delay be for the keepalives and who sends the keepalives or are the keepalives sent in both directions via remote dial up access. (we are using static routes) I know that a keepalive protocol is used by L2TP in order to allow it to distinguish between a tunnel outage and prolonged periods of tunnel inactivity. We are trying to find out if this can be done for IPSec. We have a open case with cisco tac currently to get more details and have been looking at third party web sites and RFCs. Can't find anything about latency but have found performance issues concerning bw, memory etc. Any information or sites you can direct me to would be great. Thanks!! __ Do You Yahoo!? Send instant messages get email alerts with Yahoo! Messenger. http://im.yahoo.com/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15874t=15874 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CAN SOME ONE NO EXPERMIENT CAN PASS CCNP [7:15717]
That is like saying, Why get your Bachelor's degree in Computer Science? What would you do with it? Should everyone need to work for 5 years before going to college??? Of course not!!! Just by studying for the CCNP, the person is learning a ton of valuable information... There are things that a person without a certification and tons of 'real-world' experience will never know and understand because they haven't studied the material as closely as a certified person... There are things a certified person without 'real-world' experience will not understand, because they don't have hours and hours on the equipment... Both are important, and both compliment each other. The certification shows that you have a good grasp on the technology. It shows that you are a learner and have the dedication to study and learn something... -Original Message- From: Dennis Bailey [mailto:[EMAIL PROTECTED]] Sent: Saturday, August 11, 2001 12:20 AM To: [EMAIL PROTECTED] Subject: Re: CAN SOME ONE NO EXPERMIENT CAN PASS CCNP [7:15717] Yes but why What would you do with it? PHIMHONGKONG wrote in message news:[EMAIL PROTECTED]... Hi i have a question I have no working experiment but i have some router to study at home Do i have a chance to pass ccnp? Thanks Give me a honest answer Thanks Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15875t=15717 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CAN SOME ONE NO EXPERMIENT CAN PASS CCNP [7:15717]
I agree. Also, if you get your foot in the door working for a Cisco Gold Partner, you can always count on TAC to help you if you're stuck troubleshooting. So in that case - you won't have to worry about your hiring manager letting you go if you can't figure out how to troubleshoot a problem. There are plenty of resources available. This list is one. jd -Original Message- From: mschoener [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 9:33 AM To: cisco Subject: RE: CAN SOME ONE NO EXPERMIENT CAN PASS CCNP [7:15717] That is like saying, Why get your Bachelor's degree in Computer Science? What would you do with it? Should everyone need to work for 5 years before going to college??? Of course not!!! Just by studying for the CCNP, the person is learning a ton of valuable information... There are things that a person without a certification and tons of 'real-world' experience will never know and understand because they haven't studied the material as closely as a certified person... There are things a certified person without 'real-world' experience will not understand, because they don't have hours and hours on the equipment... Both are important, and both compliment each other. The certification shows that you have a good grasp on the technology. It shows that you are a learner and have the dedication to study and learn something... -Original Message- From: Dennis Bailey [mailto:[EMAIL PROTECTED]] Sent: Saturday, August 11, 2001 12:20 AM To: [EMAIL PROTECTED] Subject: Re: CAN SOME ONE NO EXPERMIENT CAN PASS CCNP [7:15717] Yes but why What would you do with it? PHIMHONGKONG wrote in message news:[EMAIL PROTECTED]... Hi i have a question I have no working experiment but i have some router to study at home Do i have a chance to pass ccnp? Thanks Give me a honest answer Thanks Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15876t=15717 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
CCIe Written : Thank you all [7:15879]
HI All, In my joy of passing the written exam, I forgot to thank all of you who helped with my questions about study material etc.For all of you who have not written as yet, go through the mails about CCIE written here on groupstudy and you will have all you need.It helped me a lot to home in on areas I was weak on. Thanks once again, Regards Rob Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15879t=15879 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
CCNP Certification Library box set? [7:15878]
On Cisco Press's web site they are offering a CCNP Certification boxed set. At the bottom under similiar titles listed are individual books like Cisco Internetwork Troubleshooting and Building Cisco Remote Access Networks, etc. Does the books in the new Certification boxed set take the place of the older books or do these supplement them? Thanks, Jeff Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15878t=15878 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Two CPA2503 questions... [7:14445]
For those who have a CCO login the utility can be found at: http://www.cisco.com/cgi-bin/tablebuild.pl/rsl -Original Message- From: Symon Thurlow [mailto:[EMAIL PROTECTED]] Sent: Sunday, August 12, 2001 12:17 PM To: [EMAIL PROTECTED] Subject: RE: Two CPA2503 questions... [7:14445] Yes, I have a CPA2503 too, I ordered some more flash for it as you can't do anything with 4mb. You don;t need a new boot rom for it, there is a utliity you can use to change one of the SNMP MIB values, which will then make the CPA2503 report itself as being a 2503 Have a look at this http://www.cisco.com/univercd/cc/td/doc/product/software/ios11 2/fp112rn/25_1 12rn.htm#xtocid72132 It is a bit old but I think you will get the picture. I am about to do this to mine (when my new flash arrives) so will elt you know the success if you are interested. Symon -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of James Willard Sent: 01 August 2001 05:35 To: [EMAIL PROTECTED] Subject: Two CPA2503 questions... [7:14445] Hello, I recently convinced my employer to give me a Cisco CPA2503 (the white box CiscoPro router) whose power supply died. I have two questions. First of all, before I check into finding a replacement power supply, I read on this list a long way back (probably 1999ish) about someone who had made an outboard 2500 series power supply from a PC power supply. Unfortunately, I can't get a search of the archives to turn up that post that I remembered. Does anyone happen to have that link, or perhaps is the original poster still lurking? Secondly, is it true that you can order a replacement boot ROM for the CPA2500 series and make them able to load standard 2500 series images? If so, does Cisco charge for these boot ROMs, or are they like the other routers where you pay for shipping only? Thanks, James Willard, CCNA [EMAIL PROTECTED] Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15880t=14445 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
CASLOW ?? [7:15884]
Did anyone get a look at the new edition of Caslow's book Router, Bridges and Switches for CCIE's? If so, is the new information worth buying the new edition in addition to the 1st edition that I already own? Thanks _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15884t=15884 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
High FCS errors on cat5505 [7:15885]
Hello. I'm experiencing huge amounts of fcs errors on my switch. 3/1 91521 fcs errors 3/2 28078 fcs errors These counters were cleared Friday. I understand that these errors are usually media related. I've swapped cables so far which has not seemed to help. I can tell you there is a sun e450 and e250 attached to these ports. Do you know of any interoperability issues with the cat 5505 and sun NICS? Thanks In Advance, Dave Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15885t=15885 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
CCIE Written [7:15886]
Beside Boson and ccieprep practice questions, can you tell me where I can get more practice questions for CCIE written exam? Thanks in advance! Danny - Do You Yahoo!? Send instant messages get email alerts with Yahoo! Messenger. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15886t=15886 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: VPN 3000 design and PIX [7:15653]
Though some Cisco documentation says to put it in parallel to the PIX, Cisco actually prefers three ways and they all require you to go through the PIX. One way is to have the public interface of the VPN to be in the DMZ. This way the only traffic that hits the VPN has been through the firewall already. The second way is to have the private interface of the VPN to be on the DMZ. This way unecrypted traffic is forced through the PIX for inspection. The third and best way is to have both the private and public interface be on two different DMZs, so that both encrypted and unencrypted traffic is forced through PIX inspection. It's all a matter of how many interfaces you have for DMZs. Michael Le, CCIE #6811 --- Tom Richs wrote: Can someone tell me if I have a PIX in place, where should I install my VPN 3000 box (in front of the pix, behind the pix, parallel, in the dmz on the pix, etc). Also, I can't seem to find any documentation that has how to do it or how to configure each component. Any help espeically with configuration on both would be greatly appreciated. Thanks. Tom _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp [EMAIL PROTECTED] __ Do You Yahoo!? Send instant messages get email alerts with Yahoo! Messenger. http://im.yahoo.com/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15888t=15653 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Off Topic: Cisco Price List [7:15883]
Thats impossible or highly not recommended, most of us here work for a partner and pricing has a lot to do with your partner status. A general price list could be obtained by Cisco. They will be happy to send someone out. - Original Message - From: Shahir Boshra To: Sent: Monday, August 13, 2001 9:17 AM Subject: Off Topic: Cisco Price List [7:15883] Hello Group, Sorry for the Off topic posting, but I desperately need an updated Cisco price list. Can anyone please send it offline? Thanks in advance Shahir Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15890t=15883 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CASLOW ?? [7:15884]
I have both books. I would recommend the 2nd edition. The 2nd edition covers QoS and VoIP along with other topic not covered in the 1st edition. -Eric Lange -Original Message- From: Ray Smith [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 11:23 AM To: [EMAIL PROTECTED] Subject: CASLOW ?? [7:15884] Did anyone get a look at the new edition of Caslow's book Router, Bridges and Switches for CCIE's? If so, is the new information worth buying the new edition in addition to the 1st edition that I already own? Thanks _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15889t=15884 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: catalyst 2900 XL got reset [7:15835]
This is a known bug. I do believe though that the latest IOS fixes it. What are you running? a wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... hi i was trying to access the 2900XL series switch through hyperterminal and strange thing happened ,it got reset by it on.did this happened with somebody else also ,just curious to know.what could be the reason Regards Arun Sharma Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15891t=15835 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Figuring out Config Register Values [7:15894]
I have been searching high and low on Cisco's website for information on how to figure out the hexidecimal values of various Config-Register. Example, 0x2141, 0x102, 0x2142, 0x2102 etc. I would like to know how to figure out the bit value and be able to tell what each value is trying to accomplish just by looking at them. If anyone out there can help please do. Thank you _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15894t=15894 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: High FCS errors on cat5505 [7:15885]
Thanks Frank. You wouldn't happen to have sun boxes giving you problems? -Original Message- From: David Eitel Sent: Monday, August 13, 2001 12:30 PM To: [EMAIL PROTECTED] Subject: High FCS errors on cat5505 [7:15885] Hello. I'm experiencing huge amounts of fcs errors on my switch. 3/1 91521 fcs errors 3/2 28078 fcs errors These counters were cleared Friday. I understand that these errors are usually media related. I've swapped cables so far which has not seemed to help. I can tell you there is a sun e450 and e250 attached to these ports. Do you know of any interoperability issues with the cat 5505 and sun NICS? Thanks In Advance, Dave Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15893t=15885 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Off Topic: Cisco Price List [7:15883]
That's not accurate. I used to receive from Cisco (as a Cisco end-user) a monthly price list in my previous job. The standard price list is not so confidential, the partner's markup / share is confidential though. If that's really hard to get, can someone just answer me this simple question? If I need to buy an Access Server with 16 E1 PRI connections, which is cheaper? AS5400 or AS5800? My guess is 5400, but I was told that I'm wrong. Can anyone please verify this to me? Thank you once more. Shahir Donald B Johnson jr wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Thats impossible or highly not recommended, most of us here work for a partner and pricing has a lot to do with your partner status. A general price list could be obtained by Cisco. They will be happy to send someone out. - Original Message - From: Shahir Boshra To: Sent: Monday, August 13, 2001 9:17 AM Subject: Off Topic: Cisco Price List [7:15883] Hello Group, Sorry for the Off topic posting, but I desperately need an updated Cisco price list. Can anyone please send it offline? Thanks in advance Shahir Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15892t=15883 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: VPN 3000 design and PIX [7:15653]
Presumably, when traversing through the PIX, you will be translating from a private DMZ address to a Public address. This would require the IPSEC through NAT option enabled on the VPN 3000, correct? I have seen several writings stating that using IPSEC through NAT can be a security concern. I don't remember the specifics of the concerns though. Would you share that viewpoint or have you seen it to not be a problem? - JT -Original Message- From: Yonkerbonk [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 12:43 PM To: [EMAIL PROTECTED] Subject: Re: VPN 3000 design and PIX [7:15653] Though some Cisco documentation says to put it in parallel to the PIX, Cisco actually prefers three ways and they all require you to go through the PIX. One way is to have the public interface of the VPN to be in the DMZ. This way the only traffic that hits the VPN has been through the firewall already. The second way is to have the private interface of the VPN to be on the DMZ. This way unecrypted traffic is forced through the PIX for inspection. The third and best way is to have both the private and public interface be on two different DMZs, so that both encrypted and unencrypted traffic is forced through PIX inspection. It's all a matter of how many interfaces you have for DMZs. Michael Le, CCIE #6811 --- Tom Richs wrote: Can someone tell me if I have a PIX in place, where should I install my VPN 3000 box (in front of the pix, behind the pix, parallel, in the dmz on the pix, etc). Also, I can't seem to find any documentation that has how to do it or how to configure each component. Any help espeically with configuration on both would be greatly appreciated. Thanks. Tom _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp [EMAIL PROTECTED] __ Do You Yahoo!? Send instant messages get email alerts with Yahoo! Messenger. http://im.yahoo.com/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15896t=15653 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Used Rack [7:15897]
Anyone with a used 19 Network Rack in good condition to unload at a reasonable price, preferable in the New York/NJ area for the purpose of saving on shipping handling? Thanks _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15897t=15897 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: e0 on 4000-m router [7:15861]
My guess is that there really is only one Ethernet interface, but two
cabling options: AUI or RJ-45.
Use the media-type {10Baset | aui | auto-select} command to select the one
you want. Notice that supposedly auto select should figure out which one
you're using but field experience says that it doesn't sometimes.
Check CCO to make sure on this, but that's probably what's happening.
Priscilla
At 09:35 AM 8/13/01, Vik wrote:
I have a Cisco 4000 with 2 serial, 1 token ring and 2 ethernet interface.
However, when a show interfaces command is executed, there is only one
ethernet interface shown.
On the back of the router where the ethernet ports are, one is a typical
10baseT, RJ-45 connection, but the other is AUI which I do not have a
transceiver for; I just have a CAT5 cable from the 10baseT connector going
to my switch.
When I do a show interfaces command, ethernet 0 is up, but the protocol is
down. On my swith I do not see any activity lights for that port, so I am
thinking that my e0 is actually the AUI port.
How do I use the 10baseT interface?
--
Vik Evans - MCSE, CCNA, CCDA
[EMAIL PROTECTED]
Cell: (602) 677-8214
Priscilla Oppenheimer
http://www.priscilla.com
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=15899t=15861
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Strange Problem with router... [7:6293]
If you are running BGP on 3640 you are bound to have problems. Not that it wont work, but it wont be consistent. Are you running the complete BGP table? Are there any other stuff like NAT or debug running?. What is the memory you have on the router. Recommended router for BGP if you are running full BGP table is 7206 VXR. Gopal --- Kiran Kumar M wrote: Hi Peter, Thanks for your mail. But I was using the same for last 16 months, almost with same setup. I never faced this problem. mtu is default, pps it can support upto 40,000 to 70,000 (according to cisco site), in my case it never reached to that point.. Thanks, Kiran On Tue, 29 May 2001, Peter I. Slow, CCNP Voice Specialist wrote: yup. thats going to happen when you plug that many serial links into the 3640. look at the mtu, look at your pps, and look at the 2640's forwarding capabilities. i have a cusdtomer who's 2640 freaks out the same way with 8 t-1s coming into it... Peter Slow, CCNP Voice Specialist Network Engineer Planetary Networks 535 West 34th Street New York, NY 10001 Cell:(516) 782.1535 Desk: (646) 792.2395 Mail: [EMAIL PROTECTED] Fax:(646) 792.2396 - Original Message - From: Kiran Kumar M To: Sent: Tuesday, May 29, 2001 4:19 PM Subject: Strange Problem with router... [7:6293] Hi, I am facing a strange problem from last two days. One of my 3640 router is behaving in a strange manner. Sudenly it is becoming 60 - 99 % CPU utilization.(Usally 20 - 30 %) at the same time It is droping the output packets on Main Serial link (which is using for uplink/downlink) and input packets on fastethernet (Used for LAN) port. Even these Interfaces are not overloading.. On the same router I am having 17 more serial links, and 1 more fast ethernet, and one ethernet interfaces and all are in working. I am using wccp v1, and BGP also on the same router. After Observing the problem I did the following things. 1) Increased the hold-queue to 4096 2) stopped the wccp and observed the status. But there is no use. It behaved in the same pasion. So I kept the things back. I am wondering.. if anybody help me.. The traffic is same and not varying.. but it is very much flutuating.. Please give me suggestions.. if anybody have any idea.. Thanks, Kiran PS: The router is not giving this problem continuously.. for 2 mins.. its working properly.. next 2 or 3 mins.. dropping the packets.. and next 2 mins.. working properly.. FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] [EMAIL PROTECTED] __ Do You Yahoo!? Send instant messages get email alerts with Yahoo! Messenger. http://im.yahoo.com/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15898t=6293 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Figuring out Config Register Values [7:15894]
my search on 'config reg bit settings' got me this hit on the first try: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/cis2500/2509/ acsvrug/maint.htm#20837 ( To: Sent: Monday, August 13, 2001 10:10 AM Subject: Figuring out Config Register Values [7:15894] I have been searching high and low on Cisco's website for information on how to figure out the hexidecimal values of various Config-Register. Example, 0x2141, 0x102, 0x2142, 0x2102 etc. I would like to know how to figure out the bit value and be able to tell what each value is trying to accomplish just by looking at them. If anyone out there can help please do. Thank you _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15900t=15894 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: load balance between 4 T1s [7:15692]
If your running this implementation with an ISP, chances are they won't use a technology that has proved buggy: CEF. My recommendation would be to use the load balancing feature of such IGP routing protocols like OSPF or EIGRP. khramov wrote in message news:[EMAIL PROTECTED]... I am getting 4 T1s but I think I will have only one IP address. How can I load balance 1IP between 4 T1s. thanks Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15903t=15692 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Figuring out Config Register Values [7:15894]
Bri - that sounds good to me! :-) although I find that most people 1. just don't know WHAT to search for... searching on CCO is an art that evolves using practice, practice, practice, and weeding out the worthless hits 2. don't know how to find what they searched for in the webpages presented for those who are CCIE bound, it's an imperative to know the basics of the IOS documentation layout on the CD ROM. Otherwise, the search engine brings up way too much information to be sifted through during the Lab. -e- - Original Message - From: Brian To: EA Louie Sent: Monday, August 13, 2001 10:37 AM Subject: Re: Figuring out Config Register Values [7:15894] I suggest a new rule for the list. If I don't know the answer, goto CCO to search and get the answer easily, about a topic I know very little about, then I perhaps shouldn't post the results of my arduous search. Bri - Original Message - From: EA Louie To: Sent: Monday, August 13, 2001 10:45 AM Subject: Re: Figuring out Config Register Values [7:15894] my search on 'config reg bit settings' got me this hit on the first try: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/cis2500/2509/ acsvrug/maint.htm#20837 ( To: Sent: Monday, August 13, 2001 10:10 AM Subject: Figuring out Config Register Values [7:15894] I have been searching high and low on Cisco's website for information on how to figure out the hexidecimal values of various Config-Register. Example, 0x2141, 0x102, 0x2142, 0x2102 etc. I would like to know how to figure out the bit value and be able to tell what each value is trying to accomplish just by looking at them. If anyone out there can help please do. Thank you _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15902t=15894 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: High FCS errors on cat5505 [7:15885]
Yep. On the sun it show some flapping but no errors on the switch side. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15904t=15885 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: BGP and NAT [7:15859]
Are you overloading the nat? Is the neighbor statement on router A pointing to the nat address of router B? let's see your config mak wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Hi, Simply say, suppose configuring BGP between Router A and B. Router A makes a neighbor reference to the connected interface of router B. I would like to know can I configure ip nat outside on that interface on router B? Since once I configure it, after the hold time period, the BGP connection is lost and stay in Active state. Thanks a lot Regards, mak Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15906t=15859 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: load balance between 4 T1s [7:15692]
It will depend on your service provider. CEF has become much more stable in the latest IOS releases. Sprint uses CEF for load-balancing multiple T1s where the customer also has Cisco equipment. I don't know about other providers since I mainly deal with Sprint. Is there anyone else out there who can share their experiences with other ISPs? James Willard [EMAIL PROTECTED] - Original Message - From: Scott M. Trieste To: Sent: Monday, August 13, 2001 2:10 PM Subject: Re: load balance between 4 T1s [7:15692] If your running this implementation with an ISP, chances are they won't use a technology that has proved buggy: CEF. My recommendation would be to use the load balancing feature of such IGP routing protocols like OSPF or EIGRP. khramov wrote in message news:[EMAIL PROTECTED]... I am getting 4 T1s but I think I will have only one IP address. How can I load balance 1IP between 4 T1s. thanks Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15905t=15692 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Design Help [7:15907]
I would appreciate some good advice on this from some of you design boys and girls out there. I am going to upgrade some of our branch offices from ISDN and DSL to Frame Relay, and I need to find the best suited devices to do that. I want to move away from the (now) slow ISDN and unreliable (unfortunately) DSL. I have been browsing on Cisco's web site, and looking through my Cisco Product Quick Reference Guide, but I am not 100% sure I have made the right selections yet. I would like to start out connecting my main office with four of our branch offices - each with a 256 kbps bandwidth as a starter. My thoughts have been as follows: Main Office: o Cisco 2610 with a WIC-1DSU-T1= Branch Offices: o Cisco 1604 with a WIC-1DSU-T1= or o Cisco 1720 with a WIC-1DSU-T1= I am not sure if I should go with the 1604 or 1720. The 1604 has ISDN-U which I could use as a backup connection in case the Frame Relay goes down. The reason that I have not selected the 1601 with an option for a ISDN-U WIC later on, is that the T1 doesn't have a build-in CSU/DSU (why don't they have a 1600 with a fixed T1 with CSU/DCU?). The 1720 is less expensive than the 1604, and I could then add the ISDN U WIC later on if I decide that it is necessary. However, the 1700 is a VPN router, and I don't need that, since it goes directly from one router to another through the Frame Relay. I assume that this feature can be disabled. So, back to my question - what would you buy? Thanks for comments on this, Ole ~~~ Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~ http://www.RouterChief.com ~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15907t=15907 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Figuring out Config Register Values [7:15894]
I believe 2141 will boot from network ignoring nvram 102 will boot from flash using nv 2142 will boot from flash ignoring nv 2102 same as 102 forget what the 2 means - Original Message - From: Ray Smith To: Sent: Monday, August 13, 2001 10:10 AM Subject: Figuring out Config Register Values [7:15894] I have been searching high and low on Cisco's website for information on how to figure out the hexidecimal values of various Config-Register. Example, 0x2141, 0x102, 0x2142, 0x2102 etc. I would like to know how to figure out the bit value and be able to tell what each value is trying to accomplish just by looking at them. If anyone out there can help please do. Thank you _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15909t=15894 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: load balance between 4 T1s [7:15692]
are you saying that CEF is buggy? -Original Message- From: Scott M. Trieste [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 2:11 PM To: [EMAIL PROTECTED] Subject: Re: load balance between 4 T1s [7:15692] If your running this implementation with an ISP, chances are they won't use a technology that has proved buggy: CEF. My recommendation would be to use the load balancing feature of such IGP routing protocols like OSPF or EIGRP. khramov wrote in message news:[EMAIL PROTECTED]... I am getting 4 T1s but I think I will have only one IP address. How can I load balance 1IP between 4 T1s. thanks Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15908t=15692 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Figuring out Config Register Values [7:15894]
You are correct. Instead of posting a URL I've sometimes given directions page by page to show how I reached a given topic. Any thoughts on how to teach CCO navigation? -Original Message- From: EA Louie [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 1:10 PM To: [EMAIL PROTECTED] Subject: Re: Figuring out Config Register Values [7:15894] Bri - that sounds good to me! :-) although I find that most people 1. just don't know WHAT to search for... searching on CCO is an art that evolves using practice, practice, practice, and weeding out the worthless hits 2. don't know how to find what they searched for in the webpages presented for those who are CCIE bound, it's an imperative to know the basics of the IOS documentation layout on the CD ROM. Otherwise, the search engine brings up way too much information to be sifted through during the Lab. -e- - Original Message - From: Brian To: EA Louie Sent: Monday, August 13, 2001 10:37 AM Subject: Re: Figuring out Config Register Values [7:15894] I suggest a new rule for the list. If I don't know the answer, goto CCO to search and get the answer easily, about a topic I know very little about, then I perhaps shouldn't post the results of my arduous search. Bri - Original Message - From: EA Louie To: Sent: Monday, August 13, 2001 10:45 AM Subject: Re: Figuring out Config Register Values [7:15894] my search on 'config reg bit settings' got me this hit on the first try: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix /cis2500/2509/ acsvrug/maint.htm#20837 ( To: Sent: Monday, August 13, 2001 10:10 AM Subject: Figuring out Config Register Values [7:15894] I have been searching high and low on Cisco's website for information on how to figure out the hexidecimal values of various Config-Register. Example, 0x2141, 0x102, 0x2142, 0x2102 etc. I would like to know how to figure out the bit value and be able to tell what each value is trying to accomplish just by looking at them. If anyone out there can help please do. Thank you _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15910t=15894 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: HSRP with 4 MSFC's....Best practice [7:15734]
Hi All, In my production network, I got kinda the same configuration, but only one 6509 with dual supervisor engines and dual MSFCs configured. The thing is that this 6509 also run EIGRP and NAT on its MSFCs and things start to get complicated. Please help me out with this configuration: - On the first MSFC, all VLANs have higher priority and therefore should be in active mode. - On the second MSFC, all VLANs have lower priority and therefore in the standby mode. - Both MSFCs have the same static NAT and static routes, default route. - Both of them have EIGRP with same configuration and have default route redistributed into EIGRP Since I started configuring EIGRP on both of these cards, duplicating the NAT, static routes and other global command on the second MSFC so that it can be redundant to the first, something started to happen. It seems that: 1. It seems both MSFCs do the routing, even the second MSFC supposes to be in standby mode. 2. EIGRP does load balancing on both card (I can see multi paths to the default route 3. Some IP are NATed to the ip nat outside VLAN on the first MSFC, while the others NATed to that of the second MSFC (standby one). Anh some IP are NATed, but didn't work well because it experiences packet dropping... Would someone please help me out with this scenario? What did I configure wrong? Is there any way to keep the second MSFC does NOTHING (eigrp, nat, static) beside listening to the active MSFC, and kick off only if the first MSFC dies... Thanks All Thomas N. Tony Medeiros wrote in message news:[EMAIL PROTECTED]... Found my answer, From: http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/sft_6_1/configgd /redund.htm#43570 Quote: Layer 2 redundancy for the supervisor engines (one active and one in standby)-If the active supervisor engine fails (the MSFC installed on it will also fail), both Layer 2 and Layer 3 functions roll over to the redundant supervisor engine and MSFC combination. So the way I see it: For HSRP redundency for the same vlan. The standby MSFC Should be the the MSFC in the redundent supervisor. This will utilize all the replicated MLS information kept in the PFC's (or CEF information on the PFC2) This will be a faster, cleaner failover than having the standby HSRP router in the other chassis in the event of a supervisor failover. It will also keep the Layer 2 path optimal. If the whole box fails then that is a different story. The listening HSRP peers will take a little longer to come up as well as build out their MLS/CEF cache. Cool, and thanks to Jeff for the pointer. Tony M. #6172 - Original Message - From: Tony Medeiros To: Sent: Saturday, August 11, 2001 1:34 AM Subject: HSRP with 4 MSFC'sBest practice [7:15734] I have a question that really only experience will answer. I have a customer with a two 6509 core with redundant Sup's and MSFC's in each box ( a little over kill if you ask me) The setup is a typical one with access layer switch's uplinked to each core boxes with the typical L2 load balancing going on by setting up the root bridges appropriately on the core boxes. The active HSRP MSFC's correspond with the root bridges. Pretty vanilla setup. A failure of a whole core box will have the layer 2 STP and layer 3 HSRP's fail over the other core box. They are running a hybrid setup with IOS and CAT OS. So far so good. The redundant MSFC's in each box are set up as the lowest priority's so they are just in listening mode. My question is: In the case of a primary Sup failure in one of the boxes and the secondary takes over. Will the associated primary MSFC fail as well? I have never tested this and this is a production network so I obviously can't test it there. If the associated MSFC fails with the sup, It make sense to me to make the MSFC in the redundant sup the standby one so the layer 2 path stays optimal and doesn't have to pass over the inter core trunk to hit the router in the other core switch. I know this won't be optimal if the whole box fails because it takes slightly longer for a listening HSRP peer to transit to active than it does a standby peer to transit to active. I could speed things up be lowering the HSRP hello timers some. If the MSFC stays alive after a sup failure then I think I'll just leave things alone. Has anybody any experience in this type of setup? I didn't build this network but I am tasked to fix a bunch of screwups. I know this would be a moot point if they were running native IOS cus the 2 MSFC's really act as one. Any experience or comments are very much welcome I haven't posted a question in quite a while, but it feels good !! I'll be scanning CCO too in the meantime. Thanks in advance Tony M. #6172 Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15911t=15734
I have Troytec / Transcender W2K, I need Boson W2k [7:15912]
For details, pls email me: [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15912t=15912 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
CCO Navigation [7:15913]
Sure. 1. start at http://www.cisco.com/univercd/home/home.htm 2. choose Cisco IOS Software - Release 12.0 (or whatever release you're interested in - I think the Tables of Contents are close to identical from 11.3 thru 12.2, but I leave this verification as an exercise to the reader) 3. Click on Configuration Guides and Command References 4. Review that page - it gives the rundown on how the IOS documentation is organized by MAJOR TOPIC and TECHNOLOGY 5. Systematically click on every Configuration Guide link. Behind it are two more sets of table of contents links with more specialized topics. Either commit them to memory or print them out, so that you at least know where the major topics are located. 6. When that exercise is complete, realize that the Command Reference exactly parallels the Configuration Guide The other way to navigate CCO is to use the Master Indexes. That's a little trickier, because it just dumps you into a topic page without any context. However, the way to work your way backwards from that is to click the CONTENTS button on the navigation bar, which will back you out into the context and governing topics. When searching, read the actual URL that the search engine gives you and it will indicate what IOS Release the information is pointing to. I usually scroll down until I find a URL hit that has my target Release in it, and then navigate the Configuration Guide or Command Reference from there. Those are some of the methods I use for navigating CCO. Does anyone else have some helpful navigation pointers to share with us? -e- - Original Message - From: Daniel Cotts To: 'EA Louie' ; Sent: Monday, August 13, 2001 11:31 AM Subject: RE: Figuring out Config Register Values [7:15894] You are correct. Instead of posting a URL I've sometimes given directions page by page to show how I reached a given topic. Any thoughts on how to teach CCO navigation? _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15913t=15913 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Design Help [7:15907]
The first question is how many locations are we talking about. I would prefer the 1720 routers. These have the same processor as the 2600's. Don't worry about the VPN features, just don't configure them and it's not an issue. These are marketed as VPN routers because of the processing power. I believe the 1700's willl be around longer than the 1600's. Just my opinion. I work on a 300+ node frame relay network. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Ole Drews Jensen Sent: Monday, August 13, 2001 1:42 PM To: [EMAIL PROTECTED] Subject: Design Help [7:15907] I would appreciate some good advice on this from some of you design boys and girls out there. I am going to upgrade some of our branch offices from ISDN and DSL to Frame Relay, and I need to find the best suited devices to do that. I want to move away from the (now) slow ISDN and unreliable (unfortunately) DSL. I have been browsing on Cisco's web site, and looking through my Cisco Product Quick Reference Guide, but I am not 100% sure I have made the right selections yet. I would like to start out connecting my main office with four of our branch offices - each with a 256 kbps bandwidth as a starter. My thoughts have been as follows: Main Office: o Cisco 2610 with a WIC-1DSU-T1= Branch Offices: o Cisco 1604 with a WIC-1DSU-T1= or o Cisco 1720 with a WIC-1DSU-T1= I am not sure if I should go with the 1604 or 1720. The 1604 has ISDN-U which I could use as a backup connection in case the Frame Relay goes down. The reason that I have not selected the 1601 with an option for a ISDN-U WIC later on, is that the T1 doesn't have a build-in CSU/DSU (why don't they have a 1600 with a fixed T1 with CSU/DCU?). The 1720 is less expensive than the 1604, and I could then add the ISDN U WIC later on if I decide that it is necessary. However, the 1700 is a VPN router, and I don't need that, since it goes directly from one router to another through the Frame Relay. I assume that this feature can be disabled. So, back to my question - what would you buy? Thanks for comments on this, Ole ~~~ Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~ http://www.RouterChief.com ~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15915t=15907 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Design Help [7:15907]
Thanks Steve, He he, that was exactly what they told me - however, I have already told them that I want 50% CIR, and it's not that much difference once you start looking at the loop prices etc. Thanks for your input, OIe ~~~ Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~ http://www.RouterChief.com ~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~ -Original Message- From: Steve Smith [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 2:10 PM To: Ole Drews Jensen; [EMAIL PROTECTED] Subject: RE: Design Help [7:15907] Hey Ole, we use all 1720s at the lower end clients. The VPN features are only there if the right IOS is there. The 2600 should be fine. Look at your routing protocol, if you are using OSPF or something like that, you may want and probably will have to bump up the ram DRAM in the 1720 to handle it as well as the 1600. IMHO, put at least 50% cir on each line. A lot of carries will tell you if its local it does not matter but real life will tell you that is crap. Good Luck, Steve -Original Message- From: Ole Drews Jensen [ mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 1:42 PM To: [EMAIL PROTECTED] Subject: Design Help [7:15907] I would appreciate some good advice on this from some of you design boys and girls out there. I am going to upgrade some of our branch offices from ISDN and DSL to Frame Relay, and I need to find the best suited devices to do that. I want to move away from the (now) slow ISDN and unreliable (unfortunately) DSL. I have been browsing on Cisco's web site, and looking through my Cisco Product Quick Reference Guide, but I am not 100% sure I have made the right selections yet. I would like to start out connecting my main office with four of our branch offices - each with a 256 kbps bandwidth as a starter. My thoughts have been as follows: Main Office: o Cisco 2610 with a WIC-1DSU-T1= Branch Offices: o Cisco 1604 with a WIC-1DSU-T1= or o Cisco 1720 with a WIC-1DSU-T1= I am not sure if I should go with the 1604 or 1720. The 1604 has ISDN-U which I could use as a backup connection in case the Frame Relay goes down. The reason that I have not selected the 1601 with an option for a ISDN-U WIC later on, is that the T1 doesn't have a build-in CSU/DSU (why don't they have a 1600 with a fixed T1 with CSU/DCU?). The 1720 is less expensive than the 1604, and I could then add the ISDN U WIC later on if I decide that it is necessary. However, the 1700 is a VPN router, and I don't need that, since it goes directly from one router to another through the Frame Relay. I assume that this feature can be disabled. So, back to my question - what would you buy? Thanks for comments on this, Ole ~~~ Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~ http://www.RouterChief.com ~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15916t=15907 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Design Help [7:15907]
Hey Ole, we use all 1720s at the lower end clients. The VPN features are only there if the right IOS is there. The 2600 should be fine. Look at your routing protocol, if you are using OSPF or something like that, you may want and probably will have to bump up the ram DRAM in the 1720 to handle it as well as the 1600. IMHO, put at least 50% cir on each line. A lot of carries will tell you if its local it does not matter but real life will tell you that is crap. Good Luck, Steve -Original Message- From: Ole Drews Jensen [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 1:42 PM To: [EMAIL PROTECTED] Subject: Design Help [7:15907] I would appreciate some good advice on this from some of you design boys and girls out there. I am going to upgrade some of our branch offices from ISDN and DSL to Frame Relay, and I need to find the best suited devices to do that. I want to move away from the (now) slow ISDN and unreliable (unfortunately) DSL. I have been browsing on Cisco's web site, and looking through my Cisco Product Quick Reference Guide, but I am not 100% sure I have made the right selections yet. I would like to start out connecting my main office with four of our branch offices - each with a 256 kbps bandwidth as a starter. My thoughts have been as follows: Main Office: o Cisco 2610 with a WIC-1DSU-T1= Branch Offices: o Cisco 1604 with a WIC-1DSU-T1= or o Cisco 1720 with a WIC-1DSU-T1= I am not sure if I should go with the 1604 or 1720. The 1604 has ISDN-U which I could use as a backup connection in case the Frame Relay goes down. The reason that I have not selected the 1601 with an option for a ISDN-U WIC later on, is that the T1 doesn't have a build-in CSU/DSU (why don't they have a 1600 with a fixed T1 with CSU/DCU?). The 1720 is less expensive than the 1604, and I could then add the ISDN U WIC later on if I decide that it is necessary. However, the 1700 is a VPN router, and I don't need that, since it goes directly from one router to another through the Frame Relay. I assume that this feature can be disabled. So, back to my question - what would you buy? Thanks for comments on this, Ole ~~~ Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~ http://www.RouterChief.com ~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15914t=15907 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: I have Troytec / Transcender W2K, I need Boson W2k [7:15918]
Don't people lurk anymore before posting? William cc: Sent by: Subject: I have Troytec / Transcender W2K, I need Boson W2k nobody@groups [7:15912] tudy.com 08/13/2001 03:11 PM Please respond to William For details, pls email me: [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15918t=15918 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Figuring out Config Register Values [7:15894]
Cisco research skills are as important as configuration and design skills and almost as challenging. When you find something that someone else couldn't find, please tell us how you did it. Page-by-page navigation instructions are very helpful because they help us learn the structure of the documentation. Your Cisco career will die if you don't get good at finding stuff in the documentation, and the only way to get good at this is to spend time with it. Here's where I like to start: http://www.cisco.com/univercd/cc/td/doc/product/software/index.htm Regarding the search engine, the best advice is not to depend on it too much. It is not very effective. It's much better to know where to look in the documentation. Also, take some time to learn the search engine's caveats for those times when you really want to use it. For example, the Cisco search engine automatically adds and between the words you enter so it only returns those pages that include all of your search terms. To restrict a search further, just include more terms. The search engine does not support the logical or operator. It only returns pages that contain all the terms. You can search for phrases by adding quotation marks. Words enclosed in double quotes (like this) will appear together in all returned documents. Searches are not case sensitive. All letters, regardless of how you type them, will be understood as lower case. I discovered this the hard way. I did a search on SAID. Big mistake. ;-) But then I changed it to SAID VLAN and that was more effective. There's more info on the search engine here: http://www.cisco.com/public/extra_search_help.html Priscilla At 02:50 PM 8/13/01, Daniel Cotts wrote: You are correct. Instead of posting a URL I've sometimes given directions page by page to show how I reached a given topic. Any thoughts on how to teach CCO navigation? -Original Message- From: EA Louie [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 1:10 PM To: [EMAIL PROTECTED] Subject: Re: Figuring out Config Register Values [7:15894] Bri - that sounds good to me! :-) although I find that most people 1. just don't know WHAT to search for... searching on CCO is an art that evolves using practice, practice, practice, and weeding out the worthless hits 2. don't know how to find what they searched for in the webpages presented for those who are CCIE bound, it's an imperative to know the basics of the IOS documentation layout on the CD ROM. Otherwise, the search engine brings up way too much information to be sifted through during the Lab. -e- - Original Message - From: Brian To: EA Louie Sent: Monday, August 13, 2001 10:37 AM Subject: Re: Figuring out Config Register Values [7:15894] I suggest a new rule for the list. If I don't know the answer, goto CCO to search and get the answer easily, about a topic I know very little about, then I perhaps shouldn't post the results of my arduous search. Bri - Original Message - From: EA Louie To: Sent: Monday, August 13, 2001 10:45 AM Subject: Re: Figuring out Config Register Values [7:15894] my search on 'config reg bit settings' got me this hit on the first try: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix /cis2500/2509/ acsvrug/maint.htm#20837 ( To: Sent: Monday, August 13, 2001 10:10 AM Subject: Figuring out Config Register Values [7:15894] I have been searching high and low on Cisco's website for information on how to figure out the hexidecimal values of various Config-Register. Example, 0x2141, 0x102, 0x2142, 0x2102 etc. I would like to know how to figure out the bit value and be able to tell what each value is trying to accomplish just by looking at them. If anyone out there can help please do. Thank you _ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Priscilla Oppenheimer http://www.priscilla.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15917t=15894 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: HSRP [7:14135]
Hi All, I got kinda the same problem, but it is on the real 6509 w/ 2 sup and 2 MSFCs. Based on your message below, it seems to resolve the confusion between priority in groups. However, beside NAT, I also have EIGRP running. EIGRP does load balancing on both cards, is there a workaround for this? Also, let say I have Vlan 10 as the outside NAT interfaces on both MSFCs, so now with the load balancing of EIGRP, the NATed package still don't know with VLAN 10 it should go to (VLAN 10 on the first card or the second card?). Is it possible that I can have the same VLAN 10 on both cards, but they are on different group? Thanks All in advance! I really need your help here, since whoever setup the 6509 in our production didn't have it redundancy. We tried to configure this 6509 to do its primary job, redundancy while not breaking anything else (NAT for instant). Thomas N. Kevin Wigle wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Correct, but if you use secondary ip addresses and a different group number you can. If the original poster wanted 2 HSRP groups where one group was active on RouterA on netA and the other was active on RouterB on netB - both groups would co-exist and not bother each other. If RouterA failed then RouterB would become active on netB as well as already active on netA. The opposite holds true of course. This is also helpful in trying to load balance HSRP by splitting the user community manually, half to RouterA and half to RouterB - and maintain fault tolerance. Kevin Wigle - Original Message - From: Erick B. To: Sent: Monday, 30 July, 2001 06:51 Subject: Re: HSRP [7:14135] I don't quite understand what your asking, but... IOS will not let you configure the same HSRP/standby address or IP subnet on multiple LAN interfaces. You would have to use a different IP subnet on each Ethernet interface with a HSRP/standby address in that subnet. Were you asking that or ? --- BASSOLE Rock wrote: Hello group, I want to know if there are problems on doing a double HSRP (ethernet1 and ethernet0) with 2 routers (same configuration). Have you ever incounter any problems (Duplicate addresse, NAT, ...). Thank you. Rock BASSOLE Til: +33 (0) 1 45 96 22 03 [EMAIL PROTECTED] __ Do You Yahoo!? Make international calls for as low as $.04/minute with Yahoo! Messenger http://phonecard.yahoo.com/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15919t=14135 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: High FCS errors on cat5505 [7:15885]
Check for a duplex mis-match on the interface. It is a fairly well know issue that Sun and Cisco's don't auto negotiate well. Hard code the speed and duplex on preferably both sides, and you should the FCS errors go away. __ Thomas Crowe Senior Systems Engineer / Architect CTS - Atlanta Phone: 770-664-3900 Cell: 404-277-4089 __ -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of David Eitel Sent: Monday, August 13, 2001 1:05 PM To: [EMAIL PROTECTED] Subject: RE: High FCS errors on cat5505 [7:15885] Thanks Frank. You wouldn't happen to have sun boxes giving you problems? -Original Message- From: David Eitel Sent: Monday, August 13, 2001 12:30 PM To: [EMAIL PROTECTED] Subject: High FCS errors on cat5505 [7:15885] Hello. I'm experiencing huge amounts of fcs errors on my switch. 3/1 91521 fcs errors 3/2 28078 fcs errors These counters were cleared Friday. I understand that these errors are usually media related. I've swapped cables so far which has not seemed to help. I can tell you there is a sun e450 and e250 attached to these ports. Do you know of any interoperability issues with the cat 5505 and sun NICS? Thanks In Advance, Dave [GroupStudy.com removed an attachment of type text/x-vcard which had a name of Thomas Crowe.vcf] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15920t=15885 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Sort of Off topic / vpn question [7:15921]
Hey guys, My company is using point-to-point frame-relay (64k CIR) between an office in NY, and an office in Malaysia (Other side of the world). All of the Malaysian Internet access and email comes through NY first and then out to the Internet. It is costing us around 5k/month. We put some voice over the frame as well... Anyway, we are looking to get rid of the frame (for performance as well as cost reasons) and give the other site their own connection to the Internet. Then we will put a VPN between the two sites. We are using WorldCom for our T1 to the Internet in the NY office. WorldCom does not offer Internet services in Malaysia as of right now. However they do offer net access in Singapore which is very close by. We also have a small office in Singapore that we can use... My question is: Would we be better off going from NY to Singapore with the VPN because we can both stay with WorldCom and then bring a link from Singapore into Malaysia... Or, just go with a Malaysian service provider for their Internet access and go from NY straight into Malaysia with the VPN. I've checked both options out, and both are feasible and more cost effective than what we are doing right now. In other words, does staying with the same provider (even on the other side of the world) give big performance increases when dealing with VPNs? Thanks a million in advance for any help. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15921t=15921 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Cisco Call Manager [7:15402]
Rik, When you install the latest version of Call Manager it does a bios check. If you dont have a supported server (hardware), you wont be able to install CM. I have heard of a little program floating around Cisco that lets you install CM on any box (overlooks the BIOS thing). thanks, -Brad Ellis CCIE#5796 Network Learning Inc [EMAIL PROTECTED] used Cisco: www.optsys.net Rik Guyler wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... If you have a CCO account with the correct permissions, you can download it. Otherwise, talk to your local Cisco Account Manager for a demo or NFR version. --- Rik Guyler -Original Message- From: Rick Holden [mailto:[EMAIL PROTECTED]] Sent: Wednesday, August 08, 2001 9:04 PM To: [EMAIL PROTECTED] Subject: Cisco Call Manager [7:15402] I am looking to pass the CIPT exam and would like to get a copy of Call Manager. Does anyone know where I can get a copy or maybe a shareware voice or an eval? Thanks. /Rick Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15895t=15402 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Help need to find a good reliable datacenter in NY [7:15922]
Hi everyone. I would like to know who can provide good reliable datacenter service in NY city metro area. Basically, company that I am working for is looking for a datacenter which we can use it as pickup point for data feed from NYSE and CME (chicago Merchant Exchange ?) and reroute those data to overseas. Since I am a novice on this type of project, any info will be appreciated. I heard that Exodus is one of the excellent datacenter provider in my area. I wish to know if anyone has more detailed info. Thank you very much. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15922t=15922 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Design Help [7:15907]
Depending on how many nodes, manageability wise, pick one router, this maybe overkill for some sites, but in the long run having one model makes life easier. my 2 cent At 02:42 PM 8/13/01 -0400, Ole Drews Jensen wrote: I would appreciate some good advice on this from some of you design boys and girls out there. I am going to upgrade some of our branch offices from ISDN and DSL to Frame Relay, and I need to find the best suited devices to do that. I want to move away from the (now) slow ISDN and unreliable (unfortunately) DSL. I have been browsing on Cisco's web site, and looking through my Cisco Product Quick Reference Guide, but I am not 100% sure I have made the right selections yet. I would like to start out connecting my main office with four of our branch offices - each with a 256 kbps bandwidth as a starter. My thoughts have been as follows: Main Office: o Cisco 2610 with a WIC-1DSU-T1= Branch Offices: o Cisco 1604 with a WIC-1DSU-T1= or o Cisco 1720 with a WIC-1DSU-T1= I am not sure if I should go with the 1604 or 1720. The 1604 has ISDN-U which I could use as a backup connection in case the Frame Relay goes down. The reason that I have not selected the 1601 with an option for a ISDN-U WIC later on, is that the T1 doesn't have a build-in CSU/DSU (why don't they have a 1600 with a fixed T1 with CSU/DCU?). The 1720 is less expensive than the 1604, and I could then add the ISDN U WIC later on if I decide that it is necessary. However, the 1700 is a VPN router, and I don't need that, since it goes directly from one router to another through the Frame Relay. I assume that this feature can be disabled. So, back to my question - what would you buy? Thanks for comments on this, Ole ~~~ Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~ http://www.RouterChief.com ~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15923t=15907 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: IPSec Latency [7:15874]
The maximum delay for keepalives really depend on your phase one and phase two lifetimes. And if you have an idle timer set for your tunnels and whatever that value may be. Keepalives are mostly supported by your router or vpn box. I haven't ran across a client that supported keepalives. Although there may be one. It only takes one direct for keepalives to keep the tunnel up. As for documentation, I haven't seen any. I have been working with IPSEC for a little over a year now and I have yet to see alot of vender specific documentation, only because IPSEC is still new and being tweaked. -Original Message- From: Cisco Chic [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 10:32 AM To: [EMAIL PROTECTED] Subject: IPSec Latency [7:15874] Hi All, I was wondering if anyone has any information or sites which talk about how to tweak (if this can be done) IPSec tunnls (via keepalives) from a dial up client to a VPN5008? We have a latency of around 800 milliseconds on a network and we are trying to determine what the maximum delay can be in the network to keep the tunnel up via keepalives. How long can the delay be for the keepalives and who sends the keepalives or are the keepalives sent in both directions via remote dial up access. (we are using static routes) I know that a keepalive protocol is used by L2TP in order to allow it to distinguish between a tunnel outage and prolonged periods of tunnel inactivity. We are trying to find out if this can be done for IPSec. We have a open case with cisco tac currently to get more details and have been looking at third party web sites and RFCs. Can't find anything about latency but have found performance issues concerning bw, memory etc. Any information or sites you can direct me to would be great. Thanks!! __ Do You Yahoo!? Send instant messages get email alerts with Yahoo! Messenger. http://im.yahoo.com/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15926t=15874 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Off Topic: Cisco Price List [7:15883]
list pricing is pretty much readily available. true, the public tools on CCO do not provide list pricing. instead they refer you to a Cisco reseller. But all anyone has to do is ask, and most places I have dealt with have never had a problem divulging list. Chuck -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Donald B Johnson jr Sent: Monday, August 13, 2001 9:55 AM To: [EMAIL PROTECTED] Subject: Re: Off Topic: Cisco Price List [7:15883] Thats impossible or highly not recommended, most of us here work for a partner and pricing has a lot to do with your partner status. A general price list could be obtained by Cisco. They will be happy to send someone out. - Original Message - From: Shahir Boshra To: Sent: Monday, August 13, 2001 9:17 AM Subject: Off Topic: Cisco Price List [7:15883] Hello Group, Sorry for the Off topic posting, but I desperately need an updated Cisco price list. Can anyone please send it offline? Thanks in advance Shahir Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15925t=15883 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: load balance between 4 T1s [7:15692]
I've seen comments along those lines over on the NANOG group, if that means anything ;- Chuck -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Schneider, Matt Sent: Monday, August 13, 2001 11:43 AM To: [EMAIL PROTECTED] Subject: RE: load balance between 4 T1s [7:15692] are you saying that CEF is buggy? -Original Message- From: Scott M. Trieste [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 2:11 PM To: [EMAIL PROTECTED] Subject: Re: load balance between 4 T1s [7:15692] If your running this implementation with an ISP, chances are they won't use a technology that has proved buggy: CEF. My recommendation would be to use the load balancing feature of such IGP routing protocols like OSPF or EIGRP. khramov wrote in message news:[EMAIL PROTECTED]... I am getting 4 T1s but I think I will have only one IP address. How can I load balance 1IP between 4 T1s. thanks Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15924t=15692 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Off Topic: Cisco Price List [7:15883]
These guys have good prices on Cisco equipment... http://www.lanblvd.com I have bought 3 x 3548's and 1 x 2924 there so far, and I haven't had anything to complain about. They are (should you search on http://www.cnet.com) most often the cheapest Cisco on-line store out there. I am fixing to buy a bunch more this week. Hth, Ole ~~~ Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~ http://www.RouterChief.com ~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~ -Original Message- From: Chuck Larrieu [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 3:57 PM To: [EMAIL PROTECTED] Subject: RE: Off Topic: Cisco Price List [7:15883] list pricing is pretty much readily available. true, the public tools on CCO do not provide list pricing. instead they refer you to a Cisco reseller. But all anyone has to do is ask, and most places I have dealt with have never had a problem divulging list. Chuck -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Donald B Johnson jr Sent: Monday, August 13, 2001 9:55 AM To: [EMAIL PROTECTED] Subject: Re: Off Topic: Cisco Price List [7:15883] Thats impossible or highly not recommended, most of us here work for a partner and pricing has a lot to do with your partner status. A general price list could be obtained by Cisco. They will be happy to send someone out. - Original Message - From: Shahir Boshra To: Sent: Monday, August 13, 2001 9:17 AM Subject: Off Topic: Cisco Price List [7:15883] Hello Group, Sorry for the Off topic posting, but I desperately need an updated Cisco price list. Can anyone please send it offline? Thanks in advance Shahir Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15927t=15883 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: CCIE Written [7:15870]
Well done!! Good luck with the lab! OSN Ola Shusi wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Hi Alll, I passed my ccie written on saturday. Thanks for all your contribution. Ola Shusi Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15930t=15870 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: CCIE Written [7:15886]
The Boson's are really all you'll need . OSN Mohammed Nabelsi wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... Beside Boson and ccieprep practice questions, can you tell me where I can get more practice questions for CCIE written exam? Thanks in advance! Danny - Do You Yahoo!? Send instant messages get email alerts with Yahoo! Messenger. Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15929t=15886 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
7200 and Memory [7:15928]
Hi All,
I have here a Cisco 7204VXR with voice capability, which is having memory
problems.
I have 64Mbytes off memory e the show memory reports:
-
#show version
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-IS-M), Version 12.1(3a)T3, RELEASE
SOFTWARE (fc1)
. . . . .
ROM: System Bootstrap, Version 12.0(19990210:195103) [12.0XE 105],
DEVELOPMENT SOFTWARE
BOOTFLASH: 7200 Software (C7200-BOOT-M), Version 12.0(10)S, EARLY
DEPLOYMENT RELEASE SOFTWARE (fc1)
. . . . .
System image file is slot0:c7200-is-mz.121-3a.T3
cisco 7204VXR (NPE300) processor (revision D) with 40960K/24576K
bytes of memory.
Processor board ID 20405135
R7000 CPU at 262Mhz, Implementation 39, Rev 2.1, 256KB L2, 2048KB L3
Cache
4 slot VXR midplane, Version 2.0
As you can see there are 40960K for system memory.
But the command show process memory reports:
#show process memory
Total: 13976896, Used: 13688808, Free: 288088
PID TTY Allocated FreedHoldingGetbufsRetbufs Process
0 0 93804 18089857992 0 0 *Init*
. . . . . .
As you can see there are ONLY 13,976,896 of memory.
Any ideas about this??
Thanks in advance.
-
Eng. Paulo Roque
Network Engineer
Cisco Certified Network Associate
[EMAIL PROTECTED]
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=15928t=15928
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Off Topic: Cisco Price List [7:15883]
if in the uk, www.action.com gives a reasonable price Symon -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Ole Drews Jensen Sent: 13 August 2001 22:19 To: [EMAIL PROTECTED] Subject: RE: Off Topic: Cisco Price List [7:15883] These guys have good prices on Cisco equipment... http://www.lanblvd.com I have bought 3 x 3548's and 1 x 2924 there so far, and I haven't had anything to complain about. They are (should you search on http://www.cnet.com) most often the cheapest Cisco on-line store out there. I am fixing to buy a bunch more this week. Hth, Ole ~~~ Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~ http://www.RouterChief.com ~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~ -Original Message- From: Chuck Larrieu [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 3:57 PM To: [EMAIL PROTECTED] Subject: RE: Off Topic: Cisco Price List [7:15883] list pricing is pretty much readily available. true, the public tools on CCO do not provide list pricing. instead they refer you to a Cisco reseller. But all anyone has to do is ask, and most places I have dealt with have never had a problem divulging list. Chuck -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Donald B Johnson jr Sent: Monday, August 13, 2001 9:55 AM To: [EMAIL PROTECTED] Subject: Re: Off Topic: Cisco Price List [7:15883] Thats impossible or highly not recommended, most of us here work for a partner and pricing has a lot to do with your partner status. A general price list could be obtained by Cisco. They will be happy to send someone out. - Original Message - From: Shahir Boshra To: Sent: Monday, August 13, 2001 9:17 AM Subject: Off Topic: Cisco Price List [7:15883] Hello Group, Sorry for the Off topic posting, but I desperately need an updated Cisco price list. Can anyone please send it offline? Thanks in advance Shahir Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15933t=15883 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: CCO Navigation [7:15913]
An addition to the following. From the CCO Home Page - under Service Support go to Technical Support Help - Cisco TAC. From there go to Top Issues and scroll down. Every major area is covered. -Original Message- From: EA Louie [mailto:[EMAIL PROTECTED]] Sent: Monday, August 13, 2001 2:17 PM To: [EMAIL PROTECTED] Subject: CCO Navigation [7:15913] Sure. 1. start at http://www.cisco.com/univercd/home/home.htm 2. choose Cisco IOS Software - Release 12.0 (or whatever release you're interested in - I think the Tables of Contents are close to identical from 11.3 thru 12.2, but I leave this verification as an exercise to the reader) 3. Click on Configuration Guides and Command References 4. Review that page - it gives the rundown on how the IOS documentation is organized by MAJOR TOPIC and TECHNOLOGY 5. Systematically click on every Configuration Guide link. Behind it are two more sets of table of contents links with more specialized topics. Either commit them to memory or print them out, so that you at least know where the major topics are located. 6. When that exercise is complete, realize that the Command Reference exactly parallels the Configuration Guide The other way to navigate CCO is to use the Master Indexes. That's a little trickier, because it just dumps you into a topic page without any context. However, the way to work your way backwards from that is to click the CONTENTS button on the navigation bar, which will back you out into the context and governing topics. When searching, read the actual URL that the search engine gives you and it will indicate what IOS Release the information is pointing to. I usually scroll down until I find a URL hit that has my target Release in it, and then navigate the Configuration Guide or Command Reference from there. Those are some of the methods I use for navigating CCO. Does anyone else have some helpful navigation pointers to share with us? -e- - Original Message - From: Daniel Cotts To: 'EA Louie' ; Sent: Monday, August 13, 2001 11:31 AM Subject: RE: Figuring out Config Register Values [7:15894] You are correct. Instead of posting a URL I've sometimes given directions page by page to show how I reached a given topic. Any thoughts on how to teach CCO navigation? _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15931t=15913 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Cisco 776 M question [7:15932]
Does anyone have a working config for a 776 or something in that series for routing? The config on cisco.com stinks. It has PAT enabledI have a /29 so I don't want PAT. PAT disables all inbound traffic at the router so I have no clue why their only example for routing includes PAT. If anyone has one in working order I would love to see the upload configuration. Thanks Allen Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15932t=15932 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Design Help [7:15907]
Yes, I am working on a 40 node Frame implementation shortly, we are going to use 3640's at the head office and the 'backup' head office (mainly for future expansion capability) and 1750's with WIC-1T's. We are going 1750 in case we move to VoIP at some time in the future (probably not, but hey). Symon -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] Sent: 13 August 2001 20:28 To: [EMAIL PROTECTED] Subject: RE: Design Help [7:15907] The first question is how many locations are we talking about. I would prefer the 1720 routers. These have the same processor as the 2600's. Don't worry about the VPN features, just don't configure them and it's not an issue. These are marketed as VPN routers because of the processing power. I believe the 1700's willl be around longer than the 1600's. Just my opinion. I work on a 300+ node frame relay network. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Ole Drews Jensen Sent: Monday, August 13, 2001 1:42 PM To: [EMAIL PROTECTED] Subject: Design Help [7:15907] I would appreciate some good advice on this from some of you design boys and girls out there. I am going to upgrade some of our branch offices from ISDN and DSL to Frame Relay, and I need to find the best suited devices to do that. I want to move away from the (now) slow ISDN and unreliable (unfortunately) DSL. I have been browsing on Cisco's web site, and looking through my Cisco Product Quick Reference Guide, but I am not 100% sure I have made the right selections yet. I would like to start out connecting my main office with four of our branch offices - each with a 256 kbps bandwidth as a starter. My thoughts have been as follows: Main Office: o Cisco 2610 with a WIC-1DSU-T1= Branch Offices: o Cisco 1604 with a WIC-1DSU-T1= or o Cisco 1720 with a WIC-1DSU-T1= I am not sure if I should go with the 1604 or 1720. The 1604 has ISDN-U which I could use as a backup connection in case the Frame Relay goes down. The reason that I have not selected the 1601 with an option for a ISDN-U WIC later on, is that the T1 doesn't have a build-in CSU/DSU (why don't they have a 1600 with a fixed T1 with CSU/DCU?). The 1720 is less expensive than the 1604, and I could then add the ISDN U WIC later on if I decide that it is necessary. However, the 1700 is a VPN router, and I don't need that, since it goes directly from one router to another through the Frame Relay. I assume that this feature can be disabled. So, back to my question - what would you buy? Thanks for comments on this, Ole ~~~ Ole Drews Jensen Systems Network Manager CCNA, MCSE, MCP+I RWR Enterprises, Inc. [EMAIL PROTECTED] ~~~ http://www.RouterChief.com ~~~ NEED A JOB ??? http://www.oledrews.com/job ~~~ Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15934t=15907 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Lightstream 100 Password Recovery [7:15937]
I've seen a few posts in the archives about performing password recovery on a Lightstream 100, but no answers... Does anyone have a link or instructions on how to recover the password on one of these? -chris Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15937t=15937 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: 2501 router... [7:14553]
If we sit the lab the same day please beat me up afterwards, I dont want to bleed on the routers. - Original Message - From: nrf To: Donald B Johnson jr Sent: Monday, August 13, 2001 12:42 PM Subject: Re: 2501 router... [7:14553] One other thing. You shouldn't go around talking like you want to start a fight, and then be surprised when somebody actually takes you up on the offer. I know your title, where you work, and your work phone number. I'm not saying I'm going to peel on over, but I'm just warning you that if you continue to flame people like that, one day you're going to get your ass seriously kicked; if not by me, then by somebody else. - Original Message - From: Donald B Johnson jr To: nrf ; Sent: Monday, August 13, 2001 8:32 AM Subject: Re: 2501 router... [7:14553] Hey there its Mr Mellow. I wasn't talking to you I thought you only got fired up when provoked. O, and mellow, that spelling thing bounces of me and sticks to you cause I rubber and you are glue. hillarious - Original Message - From: nrf To: Sent: Friday, August 10, 2001 2:34 PM Subject: Re: 2501 router... [7:14553] Once again, wonderful brilliant commentary from the esteemed Mr. Johnson. We are so graced by the presence of you and your brilliant commentary. Why is it exactly that you feel the need to get off by biting other people's heads off (and doing so by using 2nd-grade level spelling skills, if you remember our last exchange)? When are you going to wake up and realize that you, sir, are an ass, always have been an ass, and always will be an ass? Donald B Johnson jr wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... If you have been here a year and don't know: a. how to research on cco b. how to check the archives c. how to connect to console d. how to change password e. that you should read a book you purchased that probably has both answers f. that there is a ccna group g. that this is helpful h. that I'm a smart a** then are we to believe that you are going to crimp a roll cable. Or are you going to build that by taking the plastic off. - Original Message - From: Schmelzer Tim L Contr 12 CPTS/FMS To: Sent: Wednesday, August 01, 2001 1:30 PM Subject: 2501 router... [7:14553] Greetings all. I'm kinda new to this game, but have been lurking here for about a year now. I have just been given a 2501 series router and now have a few questions. How do I build a console cable to connect to it? How do I clear any passwords that will be present? Is there somewhere that I can get scenarios / lab situations to practice on this router? I have purchased Todd Lammle's CCNA book and look forward to using this router with my studies. Thanks in advance for any answers, T. Schmelzer Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15940t=14553 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
show ip bgp summary [7:15938]
Question that has been killing me... On IOS versions after 12.0, the command #show ip bgp summary gives the following output: show ip bgp summary BGP router identifier 5.5.5.6, local AS number 107 BGP table version is 174, main routing table version 174 13 network entries and 15 paths using 1861 bytes of memory 3 BGP path attribute entries using 180 bytes of memory 1 BGP AS-PATH entries using 24 bytes of memory 0 BGP route-map cache entries using 0 bytes of memory 0 BGP filter-list cache entries using 0 bytes of memory BGP activity 173/1013 prefixes, 205/190 paths, scan interval 15 secs NeighborVAS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd 192.168.12.53 4 107 0 0000 neverActive 192.168.14.13 4 113 33653 33411 17400 1w6d 10 The thing that is killing me is the line BGP activity 173/1013 prefixes, 205/190 paths, scan interval 15 secs. What exactly do these fields indicate? I do not think that they are send/receive on the BGP activity because the fields are populated on a router which I cleared the BGP process and the session never left Active state, so no routes were sent/received. As for the scan interval, I think it has something to do with the BGP command #bgp scan-time , but I am not sure what changes in this field will do? Any help please!?!? Thanks! Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15938t=15938 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Installs [7:15941]
Hello all, I am new to this forum and i have a question. I have a server, a hub, a cisco core switch, and another cisco switch which i want to use as a switching agent. My question is this how do i connect them all? So far i have figured out how to connect the core switch to the other cisco switch (in port x) from which i connected the DHCP server to the switch (non-core)(in port Y). Can i connect the hub to the switch (non core) in slot z? Any help will be greatly appreciated. thanks newbie :( Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15941t=15941 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: bleeding 2501 router... [7:14553]
you won't be able to bleed on the routers - the proctor won't let you. You may, however, bleed on the keyboard and mouse of your workstation. ;-) - Original Message - From: Donald B Johnson jr To: Sent: Monday, August 13, 2001 3:56 PM Subject: Re: 2501 router... [7:14553] If we sit the lab the same day please beat me up afterwards, I dont want to bleed on the routers. - Original Message - From: nrf To: Donald B Johnson jr Sent: Monday, August 13, 2001 12:42 PM Subject: Re: 2501 router... [7:14553] One other thing. You shouldn't go around talking like you want to start a fight, and then be surprised when somebody actually takes you up on the offer. I know your title, where you work, and your work phone number. I'm not saying I'm going to peel on over, but I'm just warning you that if you continue to flame people like that, one day you're going to get your ass seriously kicked; if not by me, then by somebody else. - Original Message - From: Donald B Johnson jr To: nrf ; Sent: Monday, August 13, 2001 8:32 AM Subject: Re: 2501 router... [7:14553] Hey there its Mr Mellow. I wasn't talking to you I thought you only got fired up when provoked. O, and mellow, that spelling thing bounces of me and sticks to you cause I rubber and you are glue. hillarious - Original Message - From: nrf To: Sent: Friday, August 10, 2001 2:34 PM Subject: Re: 2501 router... [7:14553] Once again, wonderful brilliant commentary from the esteemed Mr. Johnson. We are so graced by the presence of you and your brilliant commentary. Why is it exactly that you feel the need to get off by biting other people's heads off (and doing so by using 2nd-grade level spelling skills, if you remember our last exchange)? When are you going to wake up and realize that you, sir, are an ass, always have been an ass, and always will be an ass? Donald B Johnson jr wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... If you have been here a year and don't know: a. how to research on cco b. how to check the archives c. how to connect to console d. how to change password e. that you should read a book you purchased that probably has both answers f. that there is a ccna group g. that this is helpful h. that I'm a smart a** then are we to believe that you are going to crimp a roll cable. Or are you going to build that by taking the plastic off. - Original Message - From: Schmelzer Tim L Contr 12 CPTS/FMS To: Sent: Wednesday, August 01, 2001 1:30 PM Subject: 2501 router... [7:14553] Greetings all. I'm kinda new to this game, but have been lurking here for about a year now. I have just been given a 2501 series router and now have a few questions. How do I build a console cable to connect to it? How do I clear any passwords that will be present? Is there somewhere that I can get scenarios / lab situations to practice on this router? I have purchased Todd Lammle's CCNA book and look forward to using this router with my studies. Thanks in advance for any answers, T. Schmelzer _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15942t=14553 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
IPSec FTP [7:15943]
Hello Everyone, I have a question regarding the use of FTP over IPSec. I have IPSec running from a 3640 router to a 7206. I can do just about every IP service with no problem except FTP. I say just about because I haven't tested SSH a couple others yet. Here's the problem when I run FTP client from a Unix box it works, but it takes a l time to log in. I can't use FTP client on a windows box, cause it times out. Is there some special setting I'm leaving out or do I just need to buy a card to do the job. I know a card will obviously be alot faster, but I figured with no traffic crossing the network except one FTP client, I should be able to connect with windows or whatever(This is in a test environment)!!! Could someone point me in the right direction? Thank You, Andre Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=15943t=15943 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
