Try ebay.com.au, ebay.com, sold.com.au
"Hunt Lee" <[EMAIL PROTECTED]> ¼¶¼g©ó¶l¥ó
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Does anyone know what sort of switches should I get for practicing for
> the BCMSN (Switching 2.0) exam? or for the CCIE lab? Any help or advice
> is greatly appreciated
hi all
what is the purpose of configuring sc0 interface?
thanks.
--
jeongwoo
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
A logical interface on the cisco switches to which IP address and other
parameters can be assigned.
Administrator can gain access to the catalyst by telnetting to this addr.
Regards / Thangavel
- Original Message -
From: "jeongwoo park" <[EMAIL PROTECTED]>
Newsgroups: groupstudy.cisco
T
Hi ALL,
a fast Ether port on a cisco switch (2900XL)
connected to a hub (3com repeater) 10/100 port
reports auto-negotiated full-duplex, and works fine.
How can a normal hub (no buffering!) accept full-duplex?
To my undestanding this is impossible...
Am I wrong?
And, is there a simple way to check
Better known as VLAN 1 in the IOS switches. Look @ it as a loopback
interface. As long as one port is up on the switch, you will be able to get
to it. This IP address defines what subnet the switch is on though. If you
want to uplink into a common network, set the SC0 or VLAN1 in that desired
Has anyone heard of a Serial hub or RS232 hub ??? I have purchased a =
network probe & it is missing the Tap to gain the sampling from.
Any ideas ???
Thanks
Phil
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report miscon
Hi People
I am a CCNP and would like to make an attempt at the CCIE written. Can
anyone offer any advice. I would like to know how hard this exam is, after
doing the CCNP? Which areas need to be covered that are not covered in CCNP?
Please help, I also need to know what books and study material
some 3com models include an optional uplink module which function as a
switching port... are you refering to the port?
you can use: show port capabilities {port}
correct me if i am wrong...
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Sasha
Hi all,
When I ping the loopback address the reply is much quicker than when I
ping a serial interface that is directly connected.
Why is this?
Omer Ehsna Dar
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct
oops sorry should be: show port {port}
to check the speed.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Sasha
Sent: Wednesday, March 14, 2001 5:24 PM
To: [EMAIL PROTECTED]
Subject: Full duplex and a hub
Hi ALL,
a fast Ether port on a cisco swit
Hi all,
If I want to make back to back cables to connect my routers together
what will be the requirements and should I do so? or do I have to buy
the real thing?
Thankx.
Omer Ehsan Dar
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cis
Never seen that on a hub (hubs should of course not work with duplex)
However, I have seen this 'faking full-duplex' in other situations. Lights
on the switch (and the routers) indicated full duplex but data transfers (in
different directions at the same time) seemed slow.
I cleared the count
yup there is http://www.juniper.net/training/certification/
i wonder how tough is the exam. anyone here took it?
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Deepak Sharma
Sent: Wednesday, March 14, 2001 2:20 PM
To: sipitung
Cc: Cisco group study
Pinning out the DB-60 is rather hard to do. You can go to Ebay and get the
back to back V35 cables. If you use the DTE and DCE RS-232 Cables you are
limited to 128k
Correct me if I am wrong
Tim Fermanis
GCCS System Administrator
CCNA, MCP
Getronics Government Solutions
USAFE CSS/SCOG
DS
Hi,
As you all know, we use termial server to reverse telnet into all routers in the
lab exam.
This is very convenient. However, on the terminal server, if you just press return,
it will re-open the most recent session. This is so annoying. Any good idea to
tackle this ?
Hi there,
I am due to configure a Cisco 7206VXR router with an unbalanced E1-G703
Serial Port Adpater.
I was wondering if anyone had documentation\links to information, relating
to Multilink ppp over E1.
Cheers
Ravi
_
FAQ, list archives, and subscription info:
I was afraid you'd ask that. No, I don't think it would be correct to
describe it as a routing protocol. The IP addressing is flat, and these
are switches. Its function is to allow each switch to be addressed using
IP in order to pass management traffic among them. The only IP device
outside
Can anyone tell me how to schedule a script to run on the CSS 11000 content
smart switch? I've created the script but cannot find any reference top
scheduling this..
Any help appreciated!!
Ta,
Aidan..
_
FAQ, list archives, and subscription info: http://www.group
Omer,
Do a trace to your loopback, then a trace to your connected serial
interface. The outputs will tell the story.
When you ping your connected interface, the packet has to go out on the
wire.
Pamela
On Wed, 14 Mar 2001, Omer Ehsan Dar wrote:
> Hi all,
> When I ping the loopback address t
I've met similar problem before and have solved it now. What I do is:
1. send an e-mail to them to complain about it.
2. call them to tell them the problem. ( you may check the local number of your
country on the web site )
3. they've spent more than 1 month to investigate and then told me that
I wasn't complaining, just letting folks know(I'll
keep the cash, thank you!)
--- Circusnuts <[EMAIL PROTECTED]> wrote:
> I'll pay your way if I get eveything else over the
> $300 from your first
> check as a CCIE written :o) I believe $5,000 is the
> bonus right now from
> the local Telco (V
>All,
>
>A simple question for those who have related exprience/knowledge:
>If we want to switch to another ISP, how soon we need to finish our
>readdressing?
There's no formal rule, although 30-60 days typically can get negotiated.
As a side comment, remember that when you do switch, it's prob
Hi,
I cannot distinguish the situation I should use portvlancost or portvlanpri.
Would someone can tell me?
Thanks
mak
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAI
Hi mak,
let me know what you want to do ?
First you can try
set spantree portcost mod_num/port_num cost - global port cost for a switch
port
set spantree portpri mod_num/port_num priority - global port priority for a
switch port
cu
Udo
-Ursprungliche Nachricht-
Von: mak [mailto:[EM
You would use the commands to modify the behavior of STP. To influence which
port forwards and which port blocks for a particular VLAN, on redundant
links.
Check here:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat5000/rel_6_1/cmd_ref/
setsn_su.htm#22448 (watch for word wrap) or here:
ht
I believe that you may be referring to a WANswitch. Datacom Systems makes
one. I use it in cooperation with our WAN sniffer to monitor our numerous
Frame lines. I can choose which frame line I want to monitor from the
WANswitch and I never have to worry about unplugging/replugging the serial
ca
>From: Thomas <[EMAIL PROTECTED]>
>Reply-To: Thomas <[EMAIL PROTECTED]>
>To: [EMAIL PROTECTED]
>Subject: Upgrade bootstrap
>Date: Tue, 13 Mar 2001 06:33:03 -0500
>
>Hi All - I just upgraded my 2501 bootstrap to ver 11.0(10c). This
>bootstrap
>was sent to me by Cisco. I successfully replaced the
I will be writing my bscn on friday and would like some tips or pointers
before I write.
Thanks
_
Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com.
_
FAQ, list archive
>Hi ALL,
>a fast Ether port on a cisco switch (2900XL)
>connected to a hub (3com repeater) 10/100 port
>reports auto-negotiated full-duplex, and works fine.
>How can a normal hub (no buffering!) accept full-duplex?
>To my undestanding this is impossible...
>Am I wrong?
The real problem here is t
Group,
We have a PIX 515 for a year now. There is one recurring problem which we
still cannot resolve. We opened case and talked to TAC at least two times.
Each time we were told to upgrade the code. We are now running version
5.2(3).
Here is our issue :-
We are using static public IP adddresse
>From: "Howard C. Berkowitz" <[EMAIL PROTECTED]>
>Reply-To: "Howard C. Berkowitz" <[EMAIL PROTECTED]>
>To: [EMAIL PROTECTED]
>Subject: Re: Full duplex and a hub
>Date: Wed, 14 Mar 2001 09:09:46 -0500
>
>Interestingly, until Cabletron and Cisco got into a rather nasty and
>public licensing fi
I am studying for the BCMSN and I think that is a good book to recommend but
you will need more. The objectives on Cisco's website include ATM - there
is no ATM in Cisco's book anywhere.
Tim LeBrun
CCNA, CCDA
[EMAIL PROTECTED]
-Original Message-
From: Manny Colon [mailto:[EMAIL PROTECT
Hi, group.
Can someone explain why my 2514 keeps recycling the boot phase over and
over? Here's the output with the error in bold letters. Thanks.
Router>sh ver
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-D-L), Version 12.0(6), RELEASE SOFTWARE (fc1)
Copyright (c) 19
What is the primary purpose of using the Loopback interface and can you
telnet into a router using a IP assigned to the Loopback interface. I know
the Loopback interfaces are used in OSPF and in BGP. But is there any other
purpose for them.
Regards
Asad
_
FAQ, li
I didn't have any ATM and never heard anyone else mention anything about ATM
being on BCMSN.
Tim
> -Original Message-
> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
> LeBrun, Tim
> Sent: Wednesday, March 14, 2001 4:02 PM
> To: [EMAIL PROTECTED]
> Subject: RE: Switching
Doesn't version 11.3 and above require a minimum of 16mb flash?
This is from www.cisco.com:
Platform Release Software Features
2501-2525 12.0.3 ENTERPRISE PLUS
Minimum Recommended Memory to download image - 16 MB Flash and 6 MB RAM
-
""Deloso, Elmer
For your information:
global:
! aaa authentication ppp "name" radius !!
aaa new-model
aaa authentication login default local enable
aaa authentication ppp linmethod radius
Interface:
! ppp authentication chap "name"
interface Group-Async1
ip unnumbered Ethernet0/0
Seeing as the economy is in a slow tail spin and cisco is cutting back it's CCIE
requirements for channel partners, does anyone have any comments on how difficult it
is in the
current climate and projected near future to find a job on the WAN side??
I just passed my CCNA a month ago, about to
Just sending this again, No one commented.. was this a stupid question to
ask?
> Is it true that a cisco can be configured to use the D Channell to
> remotely bring up an ISDN line on a remote router configured for dial on
> demand?.
>
> I was told sometime ago that a cisco ( also DoD ) coul
Take a look at the following link (watch the wrap!)
http://www.cisco.com/warp/public/122/crashes_swforced_troubleshooting.html
Rick Watson
Network Engineer
OUSD(Comptroller)
703.697.5710
[EMAIL PROTECTED]
-Original Message-
From: Deloso, Elmer G (WPNSTA Yorktown) [mailto:[EMAIL PROTECT
The loopbackIF never goes down.
So there is a possibility to reach this router at any time
One of the reasons for the loopback address is that you can telnet in...
Udo
-Ursprungliche Nachricht-
Von: Asad Hasan [mailto:[EMAIL PROTECTED]]
Gesendet: Mittwoch, 14. Marz 2001 16:09
An: [EMAIL
do a "show stack" and copy the output to the stack decoder on the Cisco
website. It may even be worth while opening a TAC case and send them the
output
-Original Message-
From: Deloso, Elmer G (WPNSTA Yorktown) [mailto:[EMAIL PROTECTED]]
Sent: 14 March 2001 16:59
To: '[EMAIL PROTECTED]'
S
It appears that we are going to be installing the ADSL WICs in our 2600s
in the future, but for now we're going to have about 30 locations with
either a 675 or 678. I don't mind the redirects, I just want to know by
what mechanism the hosts switch back to using the original default
gateway. Is t
Indeed, 3COM has a product called "full-duplex repeater" (what a name...).
This is actually a hybrid of a switch and a repeater: it uses buffering of
incoming
frames and a round-robin method of forwarding them to all egress ports.
However, my question concerns the common device -- no buffering.
Ho
Fairly hard. I am a CCNA doing WAN-only work for a Fortune 500 company and
have not seen near the requests for WAN Engineers that I had seen 8 months
ago. The WAN side is a very limited technical skills field, but it is hard
prove yourself with only a cert and no experience.
Kelly D Griffin, CC
This particular image isn't even 7 MB, so the flash size isn't a
problem. Here is a similar bug report that might be the problem. It
says it is present in 12.0(12) but it's the closest bug report I could
find.
Bug Id : CSCds33876
Headline software forced crash with memory corruption
Produc
I am looking for a phone line simulator to do some dial-up practice using
modems. I would appreciate any recommendation of model, price and setup. And
I wonder a low cost PABX can do the job?
I ask this because the ISDN simulator is too expensive for me and if I use
the modem dial-up for practice
We have a jobs list where this type of post should go.
Please send this stuff to [EMAIL PROTECTED] and
send the technical and networking related stuff to [EMAIL PROTECTED]
If you have any questions please read the following guidelines located at:
http://www.groupstudy.com/list/guide.html
-Origin
Hello.
I have question - How to check whitch criteria BGP use when choosed the
best path ? What IOS command can show me this ?
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations
You've really only got a few options available:
(1) Proxy ARP
(2) ICMP Redirects
(3) ICMP Router Discovery Protocol
(4) Run a routing protocol on the workstations
(5) Hot Standby Router Protocol
Of these, (4) is probably the least desirable, (3) is the least widely
supported and (5), as you said
Everyone,
I would like to upgrade to my 2500s to IOS 12.0, what is the minimum required
bootstrap or boot-image. If I were to get the bootstrap, is it a software upgrade or
hardware upgrade. How much does it cost?
Thanks for your input!
-Original Message-
From: [EMAIL PROTECTED] [mai
TelTone makes several models. Check eBay for used equipment.
> -Original Message-
> From: Joe Wong [mailto:[EMAIL PROTECTED]]
> Sent: Wednesday, March 14, 2001 9:37 AM
> To: [EMAIL PROTECTED]
> Subject: Phone line simulator
>
>
> I am looking for a phone line simulator to do some dial-u
I have taken the Juniper Internet Specialist Exam (multiple choice). If
you're looking for a comparison, then I can say that it is a lot more
demanding than any of the Cisco Exams I have taken as of yet. (CCNP, CCIE
Written).
At 03:25 AM 3/14/01, you wrote:
>yup there is http://www.juniper.n
Can someone tell me if a new 2501 comes with a transciever for the AUI to rj-45.
Justin
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
You need ISDN to practice looking at q921 and q931 issues. You will need it
to practice your multilink ppp bundles... You need to be able to configure
switch types, spids, etc. It is not a good idea to get to the lab and see
ISDN for the first time.
You can practice DDR on the modems, but that
This was discussed earlier regarding the error message for a tftp server.
However, my question was still unanswered.
As suggested, the way to correct this is as follows:
Router(config)#no service config
Router(config)#Ctrl-Z
This eliminates the error message during the session. But after clear
I am interested in knowing the technique that people use to do such
migration.
Would you allow paths to both ISP's and do some prepending of routes or
other metric manipulation
to allow for load sharing during the migration, having the entire network
migrated in a long and meticulous
process?
Wo
There is a discount listed for Groupstudy members for Teltone ISDN
simulator.
Check here for details. Zorro Mentioned the price, this link
will give you the contact information as well.
http://www.groupstudy.com/discounts/index.html
-Original Message-
From: Mask Of Zorro [mailto:[EMAIL
Hi, somebody have a configuration file from a 7500 and 2600 ISDN PRI =
TO BRI connection.
I have the PRI interfase at 7500 and the BRI in 2600 router.
Thanks for your help.
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
R
CLEAR XLATE helps ;)
Also, see how many connections you are licensed for. You may be either out
of licenses or NAT may be out of physical addresses to use for a connection.
Streaming connections hog up a big portion of NAT addresses. There is a
show command to show how much of your pool is bein
NO
>>> "Justin Clark" <[EMAIL PROTECTED]> 03/14/01 11:19AM >>>
Can someone tell me if a new 2501 comes with a transciever for the AUI to rj-45.
Justin
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and No
Anyone know if a 3102 Router's serial port is the DB-60 kind of today or
not so much?
Damian Rizzo
Senior IT Engineer
Marakon Associates
203-978-6341
[EMAIL PROTECTED]
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Repo
1)Did you order the telco line from your telco service provider.
2)Did you have ISDN simulator?
""Hugo Martinez"" <[EMAIL PROTECTED]> ¼¶¼g©ó¶l¥ó
002b01c0aca5$4e55c8c0$[EMAIL PROTECTED]">news:002b01c0aca5$4e55c8c0$[EMAIL PROTECTED]...
>Hi, somebody have a configuration file from a 7
SHOW IP BGP will list all the known routes for a given prefix
and will list the the attributes of each. To understand why it's
choosing one over another, do a search on www.cisco.com for "bgp path
selection criteria" and you'll find it.
HTH,
John
>>> "Przemyslaw Mujta" <[EMAIL PROTECTED]> 3/
The overall marketplace is reporting that spending is
not specifically slowing, but rather, that it stopped
dead. Hiring managers are taking more time to recruit
canidates, but they are still hiring. My contacts are
still looking for certifications, but, because of the
maturation process of 2000 t
Hi ALL,
After the upgrade of CAT OS and MSFC2 IOS to :c6msfc2-jsv-mz.121-5c.E8
I am getting TRACEBACK ERROR on MSFC2 card.
Has anyone encounter this error and what is the fix for this traceback
error.(Acording to CISCO this error is being going on from early IOS).
Thank you, for your help.
Mik
I've seen a million people ask about syslog for windows, but nobody has
mentioned syslogd on Unix.
I'm trying to find information on getting syslog on a Solaris platform to accept
logging messages from Cisco routers. By default, the syslog service does not
accept messages from external devices.
Guys,
I guess I need to exercise a bit more patience next time. The problem WAS
the clockrate. The thing is that I did change the clock rate to 100 on
the DCE side before posting to the group but for some reason it kept
failing. However, this morning I tried it with a clockrate of 64000
BSCN - CCNP Routing Test taken and passed. Score: 801
alot of BGP questions. Some redistribution, EIGRP and whatifs.
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EM
hey ALL I just got my 2 weeks notice at Charles schwab in Jersey City NJ I am
looking for a job with cisco /NT MCSE 1 more for CCNP any leads will be
appreciated
thanks
Get Your Private, Free E-mail from MSN
Hotmail at http://www.hotmail.com">http://www.hotmail.com.
___
general pratice, downgrade the IOS.
Waiting for Cisco release new IOS.
""Mike Peterson"" <[EMAIL PROTECTED]> ¼¶¼g©ó¶l¥ó
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
>
> Hi ALL,
>
> After the upgrade of CAT OS and MSFC2 IOS to :c6msfc2-jsv-mz.121-5c.E8
> I am getting TRACEBACK ERROR on MSFC2 card
Hi,
I have :
-- a set of CCNA 2.0 questions ( Over 1000 MC ) and notes.
-- a set of MCSE W2K questions and notes from a famous MCSE question company
I want to have transcender ( the best ) or other famous questions about MCSE
W2K.
However, if you have other CCNA 2.0 questions, you can also ema
Hi Larry,
Please check following link:
http://www.paradyne.com/cgi-bin/return?url=pagedslsb01.pl
Thanks
Abdullah Al FARUQ
Larry Osei-Kwaku wrote:
> Comrades,
>
> Has anyone read any good books on DSL . If so what are
> they ? Are there any good links or forums for DSL
> technology that yo
exactly what is accomplished by this configuration and command?
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
[EMAIL PROTECTED]
Sent: Tuesday, March 13, 2001 6:34 AM
To: [EMAIL PROTECTED]
Subject: RE: Reverse Telnet on 2600 routers not working
reve
Try ^C ^C ^C tree times at the Router>en
Mike
"Hornbeck, Timothy" wrote:
> We just received 4 new 6500's. Unboxed and powered them up, they boot
> straight to the Router> prompt. How do we get to the Switch> prompt. We
> have tried to CTRL+SHIFT+6, X and other key sequences, but have
> I've seen a million people ask about syslog for windows, but nobody has
> mentioned syslogd on Unix.
>
> I'm trying to find information on getting syslog on a Solaris platform to
accept
> logging messages from Cisco routers. By default, the syslog service does
not
> accept messages from externa
Greetings all,
Need some white papers or an info on MPLS.
Thanks
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
If you're using RS-232 cables, one DTE and one DCE and plugged them
together, your max clock will be 128k.
If you're using a 60 pin to 60 pin cable, you may have a V.35 int avail with
which you can do 4meg.
However, I forget which platform you have. some interfaces (modules)
cannot do 4 meg
22 hrs to CID examcouple of questions:
regarding SNA,.is the info in the CID text (Birkner) sufficient for what
I'll see?
also,regarding WAN Switching,do they get into the specific cards?
thanx,
dshepp806
_
FAQ, list archives, and subscription
It probably failed because that back-to-back cable is RS-232, not v.35.
RS-232 fails for me at anything over 50. V.35 can go all the way to
400.
Regards,
John
>>> "Ray Smith" <[EMAIL PROTECTED]> 3/14/01 10:22:37 AM >>>
Guys,
I guess I need to exercise a bit more patience next time. T
>From what I've heard, CCIE is considered a junior level cert when it comes
to ISP's. Comments on this? ISP consider Juniper, Nortel, Lucent certs
more appropriatewhereas CCIE would be more for the enterprise.
Curtis Call wrote:
>
>I have taken the Juniper Internet Specialist Exam (multip
http://www.cisco.com/univercd/cc/td/doc/product/dsl_prod/gsol_dsl/dsl_arch/index.htm
is a good over of DSL technology and design.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
Abdullah Al Faruq
Sent: Wednesday, March 14, 2001 9:47 AM
To: Larry Osei-Kwa
I believe google.com has them
;-]
> -Original Message-
> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
> Nabil Fares
> Sent: Wednesday, March 14, 2001 12:59 PM
> To: [EMAIL PROTECTED]
> Subject: MPLS
>
>
> Greetings all,
>
> Need some white papers or an info on MPLS
Instead of buying an ISDN simulator, can you just buy another router with
ISDN interface and connect them together, or is it not possible? The price
for the simulator is kinda steep, considering you could just buy another
router...
"Jim Dixon" <[EMAIL PROTECTED]> wrote in message
93D78DD50BC5D311
Does not- documentation, rack mounts, power cord, & console cable...
Phil
- Original Message -
From: "Justin Clark" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Wednesday, March 14, 2001 2:19 PM
Subject: New Router
> Can someone tell me if a new 2501 comes with a transciever for t
>From what I've heard, CCIE is considered a junior level cert when it comes
>to ISP's. Comments on this? ISP consider Juniper, Nortel, Lucent certs
>more appropriatewhereas CCIE would be more for the enterprise.
¨
That's my general impression. ISPs don't use non-IP protocols.
(after all,
It allows us access to a terminal device from the async AUX port. Typically,
we use the AUX as a receiving input device; that is, receiving data from a
terminal. This configuration allows us to initiate a session into an end
ASCII device from the network.
for example, if you wanted to use a ter
If my memory serves me correctly, the 3000 series routers used the DB-25
serial cables (like the AGS+) and not the high-density DB-60 connector cables
(which were introduced in the 2500/4000/7000 series routers)
http://www.cisco.com/univercd/cc/td/doc/product/access/acs_fix/cis3000/c3k2him/22616.
The following list should help...
www.mplsrc.com // The MPLS Resource Center
http://www.ietf.org/html.charters/mpls-charter.html// MPLS Working Group
http://www.cisco.com/warp/public/cc/so/neso/vvda/ipatm/index.shtml//
Cisco MPLS site (with white papers)
There are countless other goo
I want to implement cisco works in my campus. Especiall y need it for
traffic director. What are decent servers to run this software. ...
Mo Durrani
IS&T
WYSE\EDS
phone:408-473 1246
[EMAIL PROTECTED]
[EMAIL PROTECTED]
_
FAQ, list archives, and subscription info:
I'd recommend you visit www.mplsrc.com
*** REPLY SEPARATOR ***
On 3/14/2001 at 12:58 PM Nabil Fares wrote:
>Greetings all,
>
>Need some white papers or an info on MPLS.
>
>Thanks
>
>_
>FAQ, list archives, and subscription info:
>http://www.gro
I assume you are using NAT 0.
If so upgrade to 5.3.1 (no I don;t work for TAC but
NAT 0 has many problems.)
Are you using another NAT (NAT 1 or something) on top
of your NAT 0? Are you suing statics from low to
high?
Do DEBUG ICMP TRACE and ping when you are experiencing
problems and see if
It was the intent to prepare a written exam that when passed indicates a strong
readiness for the lab test. Essentially, the difficulty levels between the written
and lab are designed to be comparable, whereas Cisco's written isn't on the same level
as its Lab.
pete
*** REPLY SEPARA
sounds like config register to me.
if you do a sh ver, and it's set to something other than 0x2102 would boot
config off a tftp server, then change it
config-reg 0x2102
write your (empty) configuration
and reload
(if you're working on your certification, you'd be wise to know where that
infor
Hi Nabil, try these:
http://www.newbridge.com/doctypes/techwhitepaper/pdf/mpls.pdf
http://www.dataconnection.com/download/crldprsvp.pdf
http://www.ericsson.com/datacom/emedia/qoswhite_paper317.pdf
http://www.juniper.net/techcenter/techpapers/21.pdf
http://www.ietf.org/rfc/rfc3031.txt
You mig
MPLS Tutorial:
http://www.nanog.org/mtg-9905/ppt/mpls/index.htm
MPLS Resource Center:
http://www.mplsrc.com/
Internet Drafts on MPLS:
http://www.ietf.org/ids.by.wg/mpls.html
Cisco info on MPLS (a start anyway):
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/switch_c/xcp
No back-to-back for BRI. You could with a PRI, given the right cable and IOS
version, but that won't really help you practice for the lab exam.
Z
>From: "The.Rock" <[EMAIL PROTECTED]>
>Reply-To: "The.Rock" <[EMAIL PROTECTED]>
>To: [EMAIL PROTECTED]
>Subject: Re: Phone line simulator
>Date: Wed
RE: cisco worksI am running win 2k 512 and dual PII 450's and that seems to
do o.k. The more the memory the happier it seems to be!
-Original Message-
From: Moahzam Durrani [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, March 14, 2001 10:59 AM
To: Chris Boyd
Subject: RE: cisco work
Is the exam actually more demanding, or is the content just different? For
example, whereas the CCIE concentrates on SNA, RSRB, and token ring, I'd
imagine that Juniper concentrates more on ISIS, BGP, and MPLS. Is this the
case? If not, in what way is the Juniper exam more difficult than the
LOL...I love people...they just crack me up!
hey Nabil... go look at Foundry Networks website. Cisco also had a paper or
two on MPLS. and I believe there's a draft RFC out on MPLS, too. (I hope you
have access to the Internet...) You're obviously a very intelligent person
(since you want to k
1 - 100 of 205 matches
Mail list logo
