Windows *sucks*. I've seen it act stupid in lots of situations where a
FreeBSD laptop with the exact same configuration works just fine. I
don't have a technical explanation - I'm attributing it to excessive bad
karma.
Dom wrote:
>
> >>I've seen situations where the legal length has been nearly d
>>I've seen situations where the legal length has been nearly doubled on
full duplex connections without much apparent
>>trouble. I don't know if I'd trust a Windoze box in this kind of
configuration, but routers, unix hosts, etc, don't seem
>>to mind too much.
What is the difference between a W
:
>
> I have a question regarding the max length for a 100BaseT
> cable. Granted I
> haven't done a wealth of research on this so feel free to point
> me to
> google if the answer is mind numbingly simple, which it
> probably is
>
> I have always understoo
ED]" wrote:
>
> I have a question regarding the max length for a 100BaseT cable. Granted I
> haven't done a wealth of research on this so feel free to point me to
> google if the answer is mind numbingly simple, which it probably is
>
> I have always understood
looking at it practically, you can run cable at 150 m and still make it
work. but the question is, will it meet the reference crieteria. there are a
lot of things to be looked at here of which an important factor is
attentuation.
-Nakul
""[EMAIL PROTECTED]"" wrote in
2003 11:37
To: [EMAIL PROTECTED]
Subject: OT: Cable Lengths [7:74776]
I have a question regarding the max length for a 100BaseT cable. Granted
I haven't done a wealth of research on this so feel free to point me to
google if the answer is mind numbingly simple, which it probably is
I
I have a question regarding the max length for a 100BaseT cable. Granted I
haven't done a wealth of research on this so feel free to point me to
google if the answer is mind numbingly simple, which it probably is
I have always understood the 100M limitation on 10BaseT ethernet cable
)
ander is dte geen clockrate
Martijn
-Oorspronkelijk bericht-
Van: LINSEN Jurgen (BMB) [mailto:[EMAIL PROTECTED]
Verzonden: vrijdag 8 augustus 2003 9:37
Aan: [EMAIL PROTECTED]
Onderwerp: RE: cisco back to back cable [7:71992]
Sure you're using a cross cable?
-Original Me
Sure you're using a cross cable?
-Original Message-
From: KW S [mailto:[EMAIL PROTECTED]
Sent: Monday, July 07, 2003 6:22 PM
To: [EMAIL PROTECTED]
Subject: cisco back to back cable [7:71992]
Dear All
I have a 2501 and 2505 and I am trying to set up a homelab..These 2
routers come
es and need
> to connect to
> something like a CAT5500 with a Sup III - that requires a
> straight patch
> cable to connect to its CON port - use the AUX port on the 2511
> and the
> patch cable.
>
> > -Original Message-
> > From: John Neiberger [mailto:[EMAI
If you are using a 2509/2511 series with octal cables and need to connect to
something like a CAT5500 with a Sup III - that requires a straight patch
cable to connect to its CON port - use the AUX port on the 2511 and the
patch cable.
> -Original Message-
> From: John Neiberger [
Thanks for helping a new Cisco gurl out! I truly appreciate it. I tried it
on my as2511 and it had a few hitches but I understand what i need to change.
Thanx
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=73767&t=73671
--
**Ple
Hello
I want to connect E&M ports on Cisco routers back-to-back, but wandering how
it can be achieved. Seems Type 2 and 5 of E&M are
symmetrical, so theorically it seems possible, but pratically is it true?
If it is possible what kind of cable should I use ? Some kind of roll-over
or cr
url
do a no shut on serial intf
clock dce say 64000
then
sh controllers ser x
Look at the DCD=up DSR=up DTR=up RTS=up CTS=up
you have a working cable, interface 2x
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fint
er_r/irfshoap.htm#1019003
http
or maybe try alternating the dce/dte settings on the serial interfaces
-Original Message-
From: LINSEN Jurgen (BMB) [mailto:[EMAIL PROTECTED]
Sent: 08 August 2003 09:37 AM
To: [EMAIL PROTECTED]
Subject: RE: cisco back to back cable [7:71992]
Sure you're using a cross
Regular RJ interfaces on a 2511RJ use a rollover cable - just like the
console cable that comes with routers. They shipped green cables with the
routers - I guess to make it easy to trace them. I prefer the RJ model as I
can make cables any length. Only downside is one fast serial interface
One more possible issue.
Recently I installed a back-to-back cable in my lab. On the DCE end I
verified the cable: sh controllers s 0 - It showed DCE.
I then configured the interface;
config t
int s0
clock rate 130
ip address
no shut
end
The router returned an error message that seemed to
Hi Hitesh,
Try to check out these resources:
INCITS: http://www.t11.org
SNIA: http://www.snia.org
Cisco: http://www.cisco.com/go/storagenetworking
IETF: http://www.ietf.org/html.charters/ips-charter.html
I hope it helps...
Best regards.
Rodrigo Kazuo Yamamoto
""Hitesh Pathak R"" escreveu na me
Hitesh Pathak R [mailto:[EMAIL PROTECTED]
Verzonden: dinsdag 29 juli 2003 9:16
Aan: [EMAIL PROTECTED]
Onderwerp: Information required on Fibre cable specifications & testing
[7:73151]
Dear Group,
anybody knows some good resources on web for Fibre cables specifications
(w.r.t. Cisco products) &
Hitesh,
try here
http://www.iec.org/
or
http://www.cableu.net/fibrtech/fib62-50.htm
If u need more info, pls reply me.
Prabu
STPI-Bangalore.
On Tue, 29 Jul 2003, Hitesh Pathak R wrote:
> Dear Group,
>
> anybody knows some good resources on web for Fibre cables specifications
> (w.r.t. Ci
Dear Group,
anybody knows some good resources on web for Fibre cables specifications
(w.r.t. Cisco products) & standards.
many thanks in advance.
Hitesh
**Disclaimer
Information contained in this E-MAIL being proprietary to Wipro L
You need a T-1 crossover cable.
Jacks=RJ-48 (C?)
pinout--> I'm not really sure but I seem to recall 12-45 was the pinout for
t1 crossover.
-Nakul
""David Ristau"" wrote in message
news:[EMAIL PROTECTED]
> I've got two 2621XM routers with WIC-1DSU-T1 cards i
Isn't really just a crossover rj-45, i mean same cat5 "ends" ?
That is what I use with the pinout.
1 to 4
2 to 5
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=72596&t=72585
--
FAQ, list archives, and subscription info: http://ww
what cable do I need [7:72585]
I've got two 2621XM routers with WIC-1DSU-T1 cards in them
here at work to play around with, I want to mimic a serial connection
between the two 2621's via the WIC,
any idea as to what cable I need to use or a Cisco part number
so I can connect these to r
I've got two 2621XM routers with WIC-1DSU-T1 cards in them
here at work to play around with, I want to mimic a serial connection
between the two 2621's via the WIC,
any idea as to what cable I need to use or a Cisco part number
so I can connect these to routers together ?
TIA
FYI, it's the same as a token-ring cross-over cable.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of
[EMAIL PROTECTED]
Sent: Wednesday, July 09, 2003 4:35 PM
To: [EMAIL PROTECTED]
Subject: RE: does anyone know the pinout on a t1 cable bet/ a [7:
Hi
I'm trying to configure a Cisco ATA 186-I2 in the UK. However I am unable to
get dial tone to configure the ATA. If anyone has configured an ATA in the
UK could they please let me have the piouts between the analogue handset and
the ATA to undertake the initial configuration.
Best regards
Mal
Hi
I'm trying to configure a Cisco ATA 186-I2 in the UK. However I am unable to
get dial tone to configure the ATA. If anyone has configured an ATA in the
UK could they please let me have the piouts between the analogue handset and
the ATA to undertake the initial configuration.
Best regards
Mal
I'm thinking that even mentioning a straight through cable when
connecting two T1 interfaces together is a good way to confuse the person
asking the question. A T1 crossover is always used to directly connect
two interfaces. The pin-outs are correct for the Xover.
Bob by The Bay wrote:
gt;Sent: Wednesday, July 09, 2003 3:16 PM
> >To: [EMAIL PROTECTED]
> >Subject: does anyone know the pinout on a t1 cable bet/ a [7:72069]
> >
> >
> >3660 & an ls1010...the interfaces on both are t1
> >
> >thx in advance
> >Report misconduct
[EMAIL PROTECTED]
>[mailto:[EMAIL PROTECTED]
>Sent: Wednesday, July 09, 2003 3:16 PM
>To: [EMAIL PROTECTED]
>Subject: does anyone know the pinout on a t1 cable bet/ a [7:72069]
>
>
>3660 & an ls1010...the interfaces on both are t1
>
>thx in advance
>Report misc
3660 & an ls1010...the interfaces on both are t1
thx in advance
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=72069&t=72069
--
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report miscondu
Perhaps a copy of the configs would be helpful here.
-Original Message-
From: KW S [mailto:[EMAIL PROTECTED]
Sent: Monday, July 07, 2003 12:22 PM
To: [EMAIL PROTECTED]
Subject: cisco back to back cable [7:71992]
Dear All
I have a 2501 and 2505 and I am trying to set up a homelab..These
trying to set up a homelab..These 2 routers
> come with a cable which is a DB60(DTE) and the other end is a
DB60(DCE).This
> is wat that is label on the cable. Anyway, I try to connect this cable to
> the serial interface of the 2 routers...and both the routers are showing
> serial is down
h the wrap.
Good luck on your studies.
Mike
-Original Message-
From: KW S [mailto:[EMAIL PROTECTED]
Sent: Monday, July 07, 2003 9:22 AM
To: [EMAIL PROTECTED]
Subject: cisco back to back cable [7:71992]
Dear All
I have a 2501 and 2505 and I am trying to set up a homelab..These 2 routers
come
Dear All
I have a 2501 and 2505 and I am trying to set up a homelab..These 2 routers
come with a cable which is a DB60(DTE) and the other end is a DB60(DCE).This
is wat that is label on the cable. Anyway, I try to connect this cable to
the serial interface of the 2 routers...and both the routers
Thanks Scott! So if I didn't understand it wrong, I can just use a regular
CAT5 Ethernet cable (with all 8 pin) to connect the WIC-1DSU-T1 on the
router to that RJ48 hand-off connector from the ISP? Again, thanks!
Thomas
""Scott Chau"" wrote in message
news:[EMA
: RJ48-RJ48 cable [7:70596]
A regular cat5 ethernet cable would work. It used pin 1,2,4,5.
Scott
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of
Thomas N
Sent: Thursday, June 12, 2003 2:39 PM
To: [EMAIL PROTECTED]
Subject: RJ48-RJ48 cable [7:70596]
Hi All
Thomas,
You can use a straight-through CAT5 or CAT3 patch cable. The difference
is in the meaning of the pins. From a cabling perspective it doesn't
matter.
- Tom
Thomas N wrote:
> Hi All,
>
> I am wondering what is the difference between the RJ48 and RJ45
> connector/cab
>>>> Thomas N 6/12/03 1:19:04 PM >>>
>Hi All,
>
>I am wondering what is the difference between the RJ48 and RJ45
>connector/cable? I am setting a router with a integrated CSU/DSU
>(WIC-1DSU-T1) with a T1 RJ48 connection hand off by the ISP. They however
>do
RJ-45 and RJ-48 as used for a T1 circuit are effectively the same. As
long as the distance is not too great from the demarc to the router, Cat
5 UTP cable can be used. For long distances, shielded UTP is called for.
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On
A regular cat5 ethernet cable would work. It used pin 1,2,4,5.
Scott
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of
Thomas N
Sent: Thursday, June 12, 2003 2:39 PM
To: [EMAIL PROTECTED]
Subject: RJ48-RJ48 cable [7:70596]
Hi All,
I am wondering what is
Hi All,
I am wondering what is the difference between the RJ48 and RJ45
connector/cable? I am setting a router with a integrated CSU/DSU
(WIC-1DSU-T1) with a T1 RJ48 connection hand off by the ISP. They however
do not provide the cable. Could I make a cable with RJ45 connectors for
this? What
Thank you Dave and Kok - I appreciate your letting me know...
On Sun, 2003-05-25 at 19:29, Dave Jacoby wrote:
> Me neither.
>
> Dave
>
> ""Kok Onn Lim"" wrote in message
> news:[EMAIL PROTECTED]
> > You can forget about the two topic. I've done the exam, but didn't face
> any
> > question on
I see what you're after now. yes you can do this. the adapters are the trick
here.
cisco will use a rollover cable to essentially pair wire 1 on one end to
wire 8 on the other end (2 to 7, 3 to 6, etc...). in theory what this does
is reverses the the Tx and the Rx and the other correspo
When i plug rollover cable that i use for routers into routers console it
works. When I plug it into CSS11152 console it doesn't work When I use the
CS11152 adapter on rollover it does work. What I'm trying to figure out is
what do I have to do to a cat5 cable to make it work without th
every other cisco router (eia-232, 9600
> > baud).
> >
>
http://www.cisco.com/en/US/products/hw/accessor/ps107/products_tech_note0918
> > 6a0080094ce6.shtml
> >
> > scott
> >
> > ""Sam Sneed"" wrote in message
> > news:[EMAIL PROTECT
m/en/US/products/hw/accessor/ps107/products_tech_note0918
> 6a0080094ce6.shtml
>
> scott
>
> ""Sam Sneed"" wrote in message
> news:[EMAIL PROTECTED]
> > Has anyone done this before? I have a few CSS but don't have the
adapters
> > for console ports. I'm ho
ave a few CSS but don't have the adapters
> for console ports. I'm hoping I can create my own cable using cat5. If
> someone could enlighten me on how to do this that'd be great. Thanks.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=64393&t=64368
--
Has anyone done this before? I have a few CSS but don't have the adapters
for console ports. I'm hoping I can create my own cable using cat5. If
someone could enlighten me on how to do this that'd be great. Thanks.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&
If the Livingston port is a eia-232/DTE then you're basically set to go.
Just use a roll-over cable. On the chance that the livingston port is a
DCE, use a straight-through cable (which might be the answer since it
was a female to begin with).
scott
-Original Message-
From: John Gol
Can anyone help me for the pinouts for this cables.
>From the back of a Livingston Portmaster 2E I have a gender changer plugging
into a db25 cisco terminal to rj45 adapter.
>From here I want to plug a cat5 cable into the console of my ciscos.
I could use some help with the pinouts if
if it doesn't work, try to do this mannually in configuration mode:
ip address outside dhcp setroute retry 5
You may have to do it several times for it to work. I live in MD and my
cable modem
provider is comcast and it works.
H Howard Lewis Bloom wrote:I updated a PIX 506 with 6.2.2 an
t; interface, and
> told it to use DHCP to acquire on the outside
> interface.
>
> Comcast assigns IP addresses in the Philadelphia
> area according to the
> MAC address, so if you change the network card or
> device attached to
> the cable modem you'll get a different
the network card or device attached to
the cable modem you'll get a different IP.
I turned the modem off, attached the Pix, turned on the modem, and
then fired up the PiX.
The standard settings in the PDM should work, but it isn't.
Has anyone had any luck getting the Pix to get dhcp fr
This would work if you didn't go throgh the switch, ie from the router
console port -> patchpanel -> wall port -> to your PC (with DB converter
obviously).
SamN wrote:
>
> I wish to gain access to a router console but it's in the
> server room while
> I am outside.
> Is it possible to do someth
install a connection from the router console port to your
desk...thru patch panels or something
similar and connect the router end with a cisco blue or
black rollover cable and you have a local
console connection...
or setup a terminal server with 2511/2621 type router that
supports reverse
I wish to gain access to a router console but it's in the server room while
I am outside.
Is it possible to do something like that:, Diagram-wise:
Router---Switch---PatchPanel---User wall I/O---Computer
I mean, just the way a user would be connected to the router ethernet port,
i want to connect t
On Mon, 30 Dec 2002, Bolton, Travis D [LTD] wrote:
> I was just having a discussion with a co-worker about how companies lay
> cable across the pond and how they troubleshoot cable splices etc. Does
> anybody have any documentation or Video they can share on this? We're
just
&g
oster. Anyway here are my comments on one of the
replies to him.
Actually the sled lays on the bottom and is pulled behind the boat. Then
it works like a ditchwitch to dig a trench and put the cable inside. The
cable is spooled on the deck of the ship (the cable flows down to the
sled) and is splic
Travis,
I've often wondered the same thing. I dug this up on google. Amazingly
it dates back to the 1890s!
http://www.atlantic-cable.com/
Chuck Church
CCIE #8776, MCNE, MCSE
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=59994&t=59994
--
Team,
I was just having a discussion with a co-worker about how companies lay
cable across the pond and how they troubleshoot cable splices etc. Does
anybody have any documentation or Video they can share on this? We're just
curious on how all this works. If you do this type of work l
l news and HowTo's
-Original Message-
From: Robert Raver [mailto:[EMAIL PROTECTED]]
Sent: Monday, December 16, 2002 1:56 PM
To: [EMAIL PROTECTED]
Subject: DSL/Cable Load Balancer [7:59306]
Hey,
This is a little off topic, but I have been searching for hours with no
results. The
""Robert Raver"" wrote in message ...
> This is a little off topic, but I have been searching for hours
> with no results. There was a device featured in a magazine
> (Maximum or T3) that you could plug in both Cable and DSL lines
> and load balance in between b
Hey,
This is a little off topic, but I have been searching for hours with no
results. There was a device featured in a magazine (Maximum or T3) that you
could plug in both Cable and DSL lines and load balance in between both. Now
I need this device and cannot find it. Does anybody know of it
Hi
We had the same problem with a cat switch, I can't remember which model,
but what we did was use a standard monitor cable and cut in the ridge
with a pen knife. It was a Sunday at 11:00pm so we really had no option.
That worked and to my knowledge no problems were experienced.
your kettle or other hot object. This may be an
indication that your 7000 is going to suck some serious power 8^)
In the UK you can get one of these in the local electical store, YMMV.
rgds
Marc
NetEng wrote:
>
> I bought a 7000 router off of ebay. It did not come with a power cable
>
I bought a Cisco 7000 router off of ebay. It did not come with a power cable
and I can not find one for the life of me. I ordered and received CAB-7KAC=,
but this cable does not fit. It says on the package thats its a 7500 series
AC power cord. On ciscos website its says to order this cable but
I bought a 7000 router off of ebay. It did not come with a power cable
and I can not find one for the life of me. I purchased and received
CAB-7KAC=,
but this cable does not fit. It says on the package thats its a 7500 series
AC power cord. On ciscos website its says to order this cable but, again
The cable you mentioned should work. The AC power supplies on a 7000 and a
7507 are the same. (Unless changed recently.)
FWIW They shipped the same cord with Cat5K Power Supplies even though there
is no notch on the PS receptacle end.
Any chance that they sent you a cable for a 7513? It has a big
I bought a Cisco 7000 router at an auction. It did not come with a power
cable
and I can not find one for the life of me. I ordered and received CAB-7KAC=,
but this cable does not fit. It says on the package thats its a 7500 series
AC power cord. On ciscos website its says to order this cable but
Does anyone know where I can buy this Cisco HSSI Y cable, part-number
NTC/4203/AA? Thanks for any advice.
Cheers,
Jose Martos
Loud Packet, Inc.
26755 Jefferson Ave. Suite F
Murrieta, CA 92562
Email: [EMAIL PROTECTED]
Ask a question in our Tech Forum:
http://www.loudpacket.com/tech.html
Thank you all for your replies.
Reza
""Reza Sharifi"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> I am looking for the pinouts for DB60 (DTE) to DB50 (DCE). The cable is
> configured as DB60 (DTE) to DB50 (DCE). I need to switch it due to
Maybe you don't need to change your cable at all. DCE vs DTE is significant
at layer 1 for clocking issues. There is also DCE DTE at layer 2 for Frame
Relay purposes. The layer 1 DCE does not have to be on the same box as the
layer 2 DCE.
However if you really want another cable try Pacific
Hi all,
By the way, I have nothing to do with this seller. Just passing on a good
site to those who are interested.
Try this Web Address for Cisco Cables.
I do not think that you will be able to beat this.
http://www.anthonypanda.com
This guy has an excellent reputation on eBay as a Power Selle
Ditto!
-Original Message-
From: Mark W. Odette II [mailto:[EMAIL PROTECTED]]
Sent: Tuesday, November 26, 2002 10:01 AM
To: [EMAIL PROTECTED]
Subject: RE: Cisco DTE/DCE Cable [7:58103]
Check out the following, as it may be cheaper than building your own...
http://www.kg2.com
hope this helps.
-Drew
-Original Message-
From: Reza Sharifi [mailto:[EMAIL PROTECTED]]
Sent: Tuesday, November 26, 2002 8:46 AM
To: [EMAIL PROTECTED]
Subject: Cisco DTE/DCE Cable [7:58103]
I am looking for the pinouts for DB60 (DTE) to DB50 (DCE). The cable is
configured as DB60 (DTE
esday, November 26, 2002 7:46 AM
To: [EMAIL PROTECTED]
Subject: Cisco DTE/DCE Cable [7:58103]
I am looking for the pinouts for DB60 (DTE) to DB50 (DCE). The cable is
configured as DB60 (DTE) to DB50 (DCE). I need to switch it due to
device
configuration issues. (my 2522 is my frame relay switch and need
I am looking for the pinouts for DB60 (DTE) to DB50 (DCE). The cable is
configured as DB60 (DTE) to DB50 (DCE). I need to switch it due to device
configuration issues. (my 2522 is my frame relay switch and need to be DCE)
Can someone point me in the right direction. I check
CCO, but have not
Go to http://www.kg2.com/cables.html
The cables are around $15.00 each if you need them.
-Original Message-
From: Ernesto Diaz [mailto:[EMAIL PROTECTED]]
Sent: Friday, November 22, 2002 9:00 AM
To: [EMAIL PROTECTED]
Subject: Cisco Serial CrossOver Cable [7:57877]
Hi everyone!
Does
Here is a situation,
I have a Cisco 4000 router connected to a 2500 router back to back with a
DTE, DCE cable (4000 50 pin serial and 2500 60 pin serial.) At this time the
cable side that is connected to the 4000 is DCE and the 2500 side is DTE.
Does any body know how to swap that around (change
DTE DCE
If you want to make your own look up the specs in the hardware manual
on line.
Dave
Ernesto Diaz wrote:
>
> Hi everyone!
>
> Does anyone know the pinout for a Cisco Serial Crossover Cable (for
> interconnection of the routers via the serial ports)
>
&
Hi everyone!
Does anyone know the pinout for a Cisco Serial Crossover Cable (for
interconnection of the routers via the serial ports)
Thanks in advance
Ernesto Diaz
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=57877&
Hi All,
I have implemented Cable and DSL service providers and have seen =
that they use their own separate backbone.=20
The backbone for most cable ISP's is Hybrid Fiber Coax (HFC) where fiber =
will be laid from Headend till the nodes and nodes connects to customers =
using co-axial
Hi guys! I was wondering if someone could point
out some reading or advice concerning those MIBs. I
have a uBR7223, and i have to get all the info from
the cable modems that the uBR has. I have found this
info :
Object cdrqCmtsCmStatusEntry
OID 1.3.6.1.4.1.9.10.59.1.2.1.1
> -Original Message-
> From: Barbu Alexandru [mailto:nastybruno@;yahoo.com]
> Sent: Friday, October 25, 2002 11:40 AM
> To: [EMAIL PROTECTED]
> Subject: cable network [7:56267]
>
>
> Hi guys! I have a probem with some cable modems.
> The fact is that in the n
Hi guys! I have a probem with some cable modems.
The fact is that in the network there are around 150
cable modems and the uBR can't see more than 90. I
tried a: 'clear cable modem all reset' and the same no
of modems is seen(90). The problem was that we had a
power outage and th
On Mar 9, 5:19pm, "s vermill" wrote:
}
} Consider that the two tx leads physically tie together. So if both
stations
} were to transmit simultaneously, each would have a comparator that is
Consider what could happen if both transmitters decided to drive
the line in opposite directions for
o
} > } two simply by splitting the cable.
} >
} > Although, you can do this, I wouldn't advise it except in cases
} > where it would be very difficult to run additional cable. Also, if
} > this was the case, I would expect the hotel to provide the splitter, or
} > better
I will volunteer a similar cable I have seen a long time ago.
Only 2 pairs are required for connection. I have seen an "adaptor" where
two circuits were wired to provide two ports over one cable where there
wasn't enough wire strung.
At the patch panel two cables came
The TX/RX "loopback" is inside the NIC, from what I understand. I don't
think the senders see each other's transmissions even though their TX wires
end up being the same wire past the splitter. But I always try to work above
the physical layer and may be missing something.
Well, it's time to move
>
> No, that wouldn't make any sense. Regardless of how NICs
> determine a collision condition, it wouldn't work that a hub
> repeat back on the transmitting port. I was thinking outlout a
> post or two back.
Sometimes I am more revealing than I mean to be. That was to have been "out
loud." O
Priscilla Oppenheimer wrote:
>
> s vermill wrote:
> >
> > Priscilla Oppenheimer wrote:
> > >
> > > Back to the Ethernet question. Does the splitter simply take
> > > the four wires that 10BaseT uses and make 2 wires out of
> each,
> > > sending one of each to each port? What an awful thing to do
On Thu, 17 Oct 2002, [EMAIL PROTECTED] (John Nemeth) wrote:
> } If it was Ethernet, the only way it could have worked is if the second
pair
> } happened to go to another switch port. You can't turn one switch port
into
> } two simply by splitting the cable.
>
> Although
witch? Did
> > the switch diable the port due to the high number of
> > CRC-errored frames or did it recognize some other problem??
> Was
> > there a link light?
>
> Just for old times sake, I plugged that splitter back into a
> wall jack and tried it with our swit
hy the splitter didn't work on the switch? Did
> the switch diable the port due to the high number of
> CRC-errored frames or did it recognize some other problem?? Was
> there a link light?
Just for old times sake, I plugged that splitter back into a wall jack and
tried it with our
aying in the hostel room which has a
> > > wall port
> > > (RJ45) link to the internet. As there are two persons (two
> > PC)
> > > staying in
> > > that room. So they bought a cable splitter. (one side with
> > > one female RJ45
> > >
t; a wall port
} > } > (RJ45) link to the internet. As there are two persons (two
} > PC) staying in
} > } > that room. So they bought a cable splitter. (one side
} > with one female RJ45
} > } > jack and another side with two female RJ45 jack). So that
} > two PCs can
re are two persons (two
> PC) staying in
> } > that room. So they bought a cable splitter. (one side
> with one female RJ45
> } > jack and another side with two female RJ45 jack). So that
> two PCs can
> } > connect to internet at the same time,
> }
> }
On Mar 8, 6:25pm, "Priscilla Oppenheimer" wrote:
} Sim, CT (Chee Tong) wrote:
} >
} > Hi.. I have a friend staying in the hostel room which has a wall port
} > (RJ45) link to the internet. As there are two persons (two PC) staying
in
} > that room. So they bought a cabl
1 - 100 of 704 matches
Mail list logo