I am changing my primary email address
due to a 95% spam ratio.
I have been running filters and anti spam
programs, but I am still getting hammered.
The new email address is aero1 @ aerofoam . com
Please don't give this address to ANY 3rd. parties
or enter it in ANY forwarding sites such as e
I have enjoyed sloping my EPP P-38 and now want to electrify it by
adding two speed 400 motors.
By reversing the wiring on one of the motors the motors now rotate in
opposite directions.
It is not at all clear to me what kind of prop to put on the motor that
is rotating clockwise
I am looking for a source of the thin
covering films used on indoor planes.
Anyone have a link?
Mark Mech
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send subscribe and
unsubscribe requests to [EMAIL PROTECTED] Please note that subscribe and
unsubscribe messages
Where can I get replacement rubber for a Hi-start for hand launch gliders?
Dream Catcher is sold out.
I haven't stocked HLG sized rubber for a couple of years because
nobody ordered it. When I had 3 50's left, I made an announcement
that I wasn't going to carry it and sold the 3, but since
We haven't used the zip starts that Bruce describes for a couple of years due to the
emergence of disk launch and the difficulty of achieving reasonable equivalence
between a
zip start and disk launch. To match a good disk launch, you almost need an upstart
which
is so long .
If the HLG
Thank you for the link. I've already asked for one for my next present
from the wife.
The ultimate sin hat is the Sun Tamer
It is made from a vinyl siding type material, has an adjustable
internal basket so air circulates under it, it has a white
top and dark green bottom, so it reflects heat
If you hang vinyl min-blinds (1 or larger), save the extra vinyl slats. Or go buy the
cheapest set you can find at Wal-Mart. Or just sneak a test strip out of that set in
the
family room.
I have always favored old credit cards for squeegees, so there are 2 good supplies:
1: sign up for those
Hobby-Lobby has these histart tubing connectors that come in several sizes,
come with rings, look like a good companion to the hosemonster tubing. Myself,
I wet a suitably sized piece of wooden dowel, jam that into the rubber end,
and it clamps on like the old Chinese finger prison puzzle.
Meanwhile, the conventional wisdom seems to be you can't launch flying wings
as high as conventional tailed designs, assuming identical conditions. The
reason is the high alpha (angle of attack) in a histart or winch launch requires
you to crank in so much up-elevon, you ruin the efficiency of
Any future
shipments though with UPS will be through one of their UPS stores where I
will let them pack and ship the items for me. They guarantee a total
hassle free experience
The problem with this is that they charge 3 to 5 times more than it should cost to
ship.
I was at one of these
The cost is not 3 to 5 times what it should be, it sounds like it is 3 to 5 times
more
than you want to pay.
This is true.
I spent probably close to 2 to 3 hours dealing with UPS to file my claim plus the
receiver spent time as well taking the package back to UPS.
How often do you have to
A short time after the computerized system became effective, phase two
kicked in. That was an increase in shipping rates of all sorts. Not just the
base rate but things like the over length fee which went from $5 to $7. At
that point UPS became very expensive, relatively speaking
He's right
RCSE-List facilities provided by Model Airplane News. Send subscribe and
unsubscribe requests to [EMAIL PROTECTED] Please note that subscribe and
unsubscribe messages must be sent in text only format with MIME turned off.
I need landing practise.
I've been to a couple of contests where some fliers bring out hi-starts to
get a 3-4 m, full-house plane up high enough to shoot a landing in a
reasonable manner. The hi-start is not stretched very far and doesn't
have all that much line on it, but for this
The 29.5, especially if you
go full house IS just a toy (read novelty--and fits ALL car back
seats/trunks); if you go for full house at 40 you may be in for some
REGULAR real FUN!!
I pushed for 1m when this first started. I think it would have developed
into a more serious class. When the
Like I said in a prior post, I can get the tungsten
powder for a very reasonable price if I can order
enough of it. I will probably need to get about 20 lbs.
or more.
It is very easy to cast with paraffin and is easily removable.
I would think that I could put a kit together with about 1/2
pound
I use 1/2 (#10) SS split rings for my high starts, bungees
and mil spec bungees for launching UAV's.
They are rated at 210lbs. and I have never had a failure.
I think they are about $0.25..
Mark Mech
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send subscribe
Metric makes more sense for serious scientific and engineering work. One of
the best kept secrets in the US is that the place is really metric. They do
hide it well
Most of the aerospace machine shops I have dealt with use
100th's and 1000th's of an inch as their standard unit of measurement.
Matt, email again,
my spam filters got your first one!
I still have at least 6 of the digital servos left.
Sorry about the bandwidth!
Mark Mech
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send subscribe and
unsubscribe requests to [EMAIL PROTECTED] Please note that
Does anyone know of any free
down load programs that would allow my to scale a foil
and email the scaled coordinates?
Mark Mech
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send subscribe and
unsubscribe requests to [EMAIL PROTECTED] Please note that subscribe and
I just finished updating some of my Hose Monster
Bungee pages: www.aerofoam.com/hosemonster.html
I added some rubber specifications and will be adding
some pictures in the near future.
I have also added the option of ordering a high start
with bright yellow 100lb. Spectra line.
I recommended this
Tom is right on point. I'd like to see a good definition that clearly
divides the scale/performance planes that happen to be made from EPP
from the EPP combat wing and the like.
It is usually easy to differentiate at first glance.
It is obvious if a plane is built to be scale or for
Does anyone know Robert Kartmans email address?
He had done some laser cutting for some of my kits.
I am in need of some more laser cut parts, if anyone
is interested in cutting them, send a reply to this email.
Mark Mech
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News.
OK guys I need advice from the super geeks.(I know there are a few of you out there)
It is time for a new laptop (or a desktop AND a laptop) for Aerofoam.
I have been looking, but haven't made any firm choices.
It must have:
P4 at least 2.4ghz.
60 to 80gig HD.
Video inputs so I can use
I have a NIB Aveox 36/15/4 brushless motor with a 3.7 to 1 gear box
and a SH-18 programmable speed controller for sale.
The speed controller and gearbox have had 2- 10 minute flights on
one of my UAV's, the first motor was defective and burned to a crisp
while only drawing about 12 to 15 amps, so
Well if you can see, and controll, and tell what a 2-meter ship is doing at
4100 feet!
Then you must be Superman!
I have to agree with Charlie, I have flown one of my 8ft. deltas to around
2500ft. I verified this by measuring the distance on the ground and
using the altitude gauge on my marine
The weight of the BOT is around 60 oz. or 3.75 lbs. The rubber
should have a cross section (unstretched) of around 0.1 sq. in. That
weight of rubber is usually described by words like standard, 3
meter, L or heavy duty.
A good rule of thumb is that the rubber should have a tension equal to
a bagged foam core wing. The skin is 3/4 oz. cloth
I hit a wing tip and
now have a compression failure of the upper skin. The
wing is still basically strong in that it not very
flexible where the failure is. I am looking for the
best way to stabilize the area
Here is a technique I have been
. Now if someone who had the moxy and equipment and was willing to
offer a set of Genie wings I gotta believe there is a market out there.
I would be interested in a good set of wings like this myself.
I have the equipment, but don't have the time..
I would probably end up building a Mantis
What is the shortest bungee you'd dare to launch an open class sailplane
with? I'd like to get it about 50 ft high to practice landings. What
diameter tubing would be best?
Most people use the standard 1/2 x 25' bungee,
($38.00 shipped with connectors installed.)
This will take the average
Batteries are dangerous the worst battery incident
I ever saw happened when a bunch of sealed Gates D-Cell Lead Acid
I am now testing a plane using an 8amp 22v Li-poly pack and it makes
me very nervous. is it possible to put a fuse on the pack in case of a dead short?
The motor can pull up to
The 9C may have it's shortcomings but at a price point roughly 1/3
of the EVO it offers a great deal of functionality, particularly to
someone like myself, making the move from park flying to more
serious TD.
It's a lot more than that!
I have had the 8uaf, 8uafs and now the 9C. It is so
The Quad is very nice. 4 ports ALL at 1 amp each. Perfect for my large
aerobatic planes with 2 RX packs and the ignition pack plus the TX.
This brings up another question, I have been flying some large planes with
2600 nimh flight and ignition packs. They are the most current cells
that can
There was a similar fiber available in cloth from a British source,
I think it was called Dynel or something similar.
The home built boat community liked it for the final
layer on the bottom of the boat. It was so abrasion
resistant that you could beach the boats with very little
wear. This
I posted this before, but under my other email address, so it will take a day or 2 to
show
up!
Here is is again the first time, sort of.
Does anyone know of a killer deal on a fairly
fast PC 1.2GHZ or faster with an invidia graphics card
and reasonable amounts of RAM on the pc and video card?
If you want a wagon, consider a post 1983 Mercedes Turbo Diesel Wagon.
These cars sell for less than $7K used, get about 30 miles per gallon on
diesel fuel which is usually cheaper when gas prices spike and this car
has plenty of power.
The maintenance consists of oil and fuel filter changes and
What is the best program for calculating motor, prop, gearbox, battery
combinations???
Mark Mech
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send subscribe and
unsubscribe requests to [EMAIL PROTECTED] Please note that subscribe and
unsubscribe messages must be
I think Hitec wins the contest in Best web page with good information.
Hitec wins on everything that is service related.
Mark Mech
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send subscribe and
unsubscribe requests to [EMAIL PROTECTED] Please note that subscribe
At a $130 for the Craftsman, its a marginal value,
but its a much better saw than the Tradesman. If I was in the market, I'd
wait for the Craftsman to go on sale. By the way, the Tradesman is only a
1/4 hp. You get what you pay for.
1/4hp is plenty for a small bandsaw.
Every now and then
It actually has some unrelated amines that are on the surface or will
migrate to the surface
That was supposed to be un-reacted amines, my spell checker fixed it and
sent it
before I could stop it!
Mark Mech
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send
I have to question the statement about counterbalancing. The
kind of mass we are concerned with is rotational mass, i.e. moment
of inertia. Counterbalancing increases MI, the opposite of what we
want.
But it increases the rotational mass without increasing the surface area, so
the
I'd like to make a variety of different wings but don't have the tools,
time or patience (emphasis on tools and patience) to make my own
templates. Is there anyplace out there or anyone who makes templates or
a system of trading templates or renting them?
Go to Home depot and get some
When I was a kid back in the late '70's my R/C mentor was the town funeral
director. He was using CA on the stiffs when ZAP was first introduced. He
pushed everyone in the club to try it as he knew how useful it was.
I still remember the first blue hotstuff that stuff was so volatile, you
PS, one of the reasons for this landing was to minimize time and people in
the landing zone.
You know right away what the score is and you don't need to measure.
We wouldn't have been able to turn the LZ around for upwind landings because
the planes would then have to make their final over the
Let me get this right, you state and I quote: If the market stops
supporting a business, there will be
change.Lets see, Multiplex got bought out, that's change. I guess
someone stopped supporting their business. OK, who done it? Who stopped
supporting Multiplex. It wasn't me...I just
This Sierra 2.5m glider is advertised as for F3f. Is anyone flying it? It
looks good and the price is about what I was shooting for to get these guys
an entry level glider.
I have heard good things about this plane, good thermal performance and
good on the slope.
A club in Olympia is
I would like to upgrade to a Speed 400/480 size brushless motor,
probably one for direct drive and one for a planetary gear box. If
anyone has suggestions as to which is the best, most reliable,
I have been told about a fairly new motor.
The motor is the aerix speed 280 brushless. there are
Check the link I posted. I first posted on RCSE about these almost
2 years ago, and recommended them several times on RCSE since then :)
Anyways, no matter how you found out about them, I'm glad you like 'em.
Thanks for adding your comments. Can't imagine why not to use the cool
clips
Again, Hecells are at their max current rating as well with this motor. If
you run these cells at more than 16 or so amps for very many flights you
end
up with an 850mah cell very quickly. Use them under 16 and they will last
you a while @ 1050mah. Sanyo has a cell out early next year that is
Lee wrote:
I have a variety of composite structures that need to be filled. I have
been using hardware store Bondo for this lately. It works well enough
except it is way too hard, difficult to sand to a finish without boogering
up the surrounding surfaces. It's also rather heavy.
There are 2
Always a good idea to register software that is purchased, and to keep the
installation codes for software somewhere other than the computer you
installed the software on
I never register software, except for Norton for services.
I do write the codes on the disk with permanent ink.
Any free
Polypropaline doesn't bond to much of anything. In order to get a
permanent bond it needs a surface treatment. In industrial settings
the preferred method is to expose it to fluorine gas but that's REALLY
nasty stuff and not for amateures. A much safer, though less
effective, alternative
I have a 48 EPP foamie covered in strapping tape, then Ultracote. One of
the wings is twisted and I'm wondering if there is a way to fix this
If the strapping tape was put on with uneven ntension, you are sort of
screwed.
However!, you can try blocking the plane in some wood scraps with
I just got spammed by the guy from FVK models
Whats the world coming to?
Mark Mech
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send subscribe and
unsubscribe requests to [EMAIL PROTECTED] Please note that subscribe and
unsubscribe messages must be sent in text
Do not go to the website, it is a new form of virus that hacks your address
book and send out messages, just visiting the site can do this if you don't
have appropriate firewalls.
Mark Mech
www.aerofoam.com
- Original Message -
From: James V. Bacus [EMAIL PROTECTED]
To: [EMAIL
What's the best way to join two pieces of surgical tubing on a
highstart.
The best way is to use a solid rod that is about 1.5 to 2 times larger in
diameter than the OD of the tubing.
It can be aluminum or nylon, it really doesn't atter except that it needs to
be strong and the ends need to
be
Wow, what a project! I'm not sure I would want to risk a maiden flight.
Just put it into the museum. ;^)
After seeing the picture of such a fragile balsa ship, I would recommend
serious bicycle testing (see my trimming wings page).
The bicycle is your portable wind tunnel. You can also do this
I am just finishing a room in the basement. This room will be my new
shop. It is ~13*15 feet. My question goes out to those who have had a
shop, have a shop or who have dreams for a shop. What is important to
include in the shop
I have built my shop into a 7'x22' Aljo travel trailer ($250.00
Does anyone have a Corel Photopaint 7 disk #1 ?
I lost disk #1 and lost the program when my HD crashed in April and haven't
been able to reload the program.
Corel only supports the past 2 versions, so I am screwed..
I really need to edit some photos for the web site.
Soaring
You need to protect it from ozone and UV, the good stuff (Mine!)
www.aerofoam.com/hosemonster.html
is loaded with carbon black for UV protection.
I will be getting the rubber milk Hollyday Designs sold for treatment.
There are a number of protectants that are available, armor all is probably
the
I just found out there is a slimer club about 5 miles from me, there is a
slope about 12 miles away and I fly my Noseeum at the ferry landing (3miles)
or in front of my house...
Mark Mech
[EMAIL PROTECTED]
remove NOSPAM the address
or just hit reply
Not only are they self-insured, but they are talking about raising
membership dues because of it. They say that an increase is needed. How
long ago did the Board vote to give Joyce Hager some big bonus?
This sounds more like it, from what I understand, the insurance premium is
less than
in 1# EPS
Root Chord: 12
Tip Chord: 5
Wing Span: 34 (17 per wing)
Airfoil: SD7003 with thickness at 8.514% and camber at 1.482%
From what I understand the original foil was modified at under side of the
trailing edge area.
It has a good roll rate and is very aerobatic.
That being said,
What problems would I face if I converted a
rudder/elevator ship to a rudder/elevator/wingeron
ship - with a wing that has dihedral?
My Mosquito Hawk fits your description. (that is why it was named)
It has curved dihedral in the tips and a bit of dihedral in the center
panels.
It works well,
I just got in some really great kits. These are fully molded EPP flying
wings.
These are the most complete kits (includes all the tape and hardware) that
I have seen yet. They also come with more than two dozen light sticks.
And the price is amazing:
Ahh, the cheap Chinese knock offs have
Well, it doesn't quite work for me. The HLG was all over the sky.
The release isn't consistent. Sometimes the glider will launch
horizontally, sometimes vertically. But it took no effort to
launch it fast enough to make it howl,
It works great if the plane is light enough and strong
Only 2 hours left to bid on the 2 Meter Geraris Fox.
Do I have to sell it this cheap?? (yep, ebay policy)
Only if you were foolish enough to not set a reserve!
You can always submit a reserve high bid yourself and then you will buy it
from yourself unless there is a higher bid.
Has anyone ever had the Uline tape get old and not
stick well? My tape is about 2-3 years old and I did
the 3m77 but it wants to come up. Not good
considering I have to fly this weekend.
The Uline tape is inferior compared to the 3m tape, I stay away from it.
Tiplets can be attached with
With an experienced modeler's help (meaning yourself), you can instruct
with
many different models. However, it will not be ideal. If your only looking
for a plane which will be impressive in YOUR hands, he'll love it.
I don't totally agree with this,I have taught a few people on my Avros
..Thinking too much about
design, can make you fall off your thermal
I think this needs to be a T-shirt!
Mark Mech
[EMAIL PROTECTED]
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send subscribe and
unsubscribe requests to [EMAIL PROTECTED]
This is a hoax, do not delete the file, windows uses the file and you will
be out on a limb.
Mark Mech
[EMAIL PROTECTED]
www.aerofoam.com
- Original Message -
From: Paul Rickie Clark [EMAIL PROTECTED]
To: [EMAIL PROTECTED]; [EMAIL PROTECTED];
[EMAIL PROTECTED]; [EMAIL
Daryl said:
So what are you looking for? Control throws? CG? Hook position?
Let me take some time out and make this easier for you all:
Control throws - Adjust to taste
CG - Adjust to taste
Hook position - Should rotate hard - adjust to taste
I have to second this.
When I first heard
I am on a couple of boating lists and the discussion of deep cycle batteries
comes up occasionally.
The best value for the money is the Trojan golf cart battery, it comes in
6v and 12v. Most people like the 6v. because the plates are a bit thicker
and they tolerate abuse better, but the 12v can
For sale:
2 NIB Artimus KC's.
One has a KC fuselage and wing $625 plus shipping.
One has a standard glass fuselage and KC wing $600 plus shipping.
There are pictures at:
www.aerofoam.com/artipage.htm
Mark Mech
[EMAIL PROTECTED]
www.aerofoam.com
RCSE-List facilities provided by
Hi Stan -- You have hit on the reason I had Pete Waters do his magic. It
avoids the headache of turning on the TX, and while its on -pulling the
module out and reinserting it - and at that point the flashing RF
indicator
goes from flashing to steady
I have never had to do that with my
- How can we make sure, or at least fairly sure, this won't happen
again?
Yes, that is the question. Last week most Americans would have bulked at
being photographed and fingerprinted before being allowed to board an
airplane. Perhaps not today. I do not believe my personal freedom would
Well, since they use it for signs, I'd call up the local sign shop and ask
what screen printing ink they use on the signs.
They don't print on the coroplast, they print on sign vinyl, then stick it
on the coroplast, or they cut they letters out and stick them on.
You can get spray paints to
How about Utracote, will that stick to coroplast? I'm getting my JW kit
shortly
and I would like to cover the coroplast fin.
Only if you put contact cement on the fin first, you are better off covering
the fin with sign vinyl or colored packing tape, I usually wipe it down with
a harsh
Try using vinyl paint, it's flexible, comes in spray cans of many colors.
It can be bought at most auto parts stores. (it's used for painting car
interiors)
Very thick and heavy
I have used it on wingtips of epp planes though, but Dip It is better for
tips.
Mark
Has anyone experimented with taking apart one of those super bright led
lights you can find at REI or other outdoor places? I think they are
called
sapphire LED's. I was thinking of doing this for my slowflyer as landing
lights.
You can buy the super bright white or blue LED's, they can
I just recieved the email below with a pif. doc. attached that had a virus.
I new it had the virus because this is the 4th one I have received with the
same message. The subject surprized me though, it is apparently
targeted..
Watch out for any of the emails that say they want your advice on
Hi Mathew, (rcse), I don't have the virus, I have had it sent to me a few
times.
I have never opened it and have done numerous Norton scans.
Mark Mech
[EMAIL PROTECTED]
www.aerofoam.com
- Original Message -
From: Matthew Orme [EMAIL PROTECTED]
You are infected with the
I just got spammed by the AMA!!
What were they thinking?
They have now destroyed the last shreds of credibility that they were
hanging on to. It's a sad day in modelville.
Mark Mech
[EMAIL PROTECTED]
www.aerofoam.com
RCSE-List facilities provided by Model Airplane
However, you can still become infected with the
backdoor/security-comprimise part of the virus. I use Eudora and I
absen-mindedly double clicked on an attachment from someone I trusted,
assuming it was an image (I read "gif" when it was really "pif").
Although
it did not send out any email,
There was a guy in Phx. that was in to the high end rocket gliders, he was
going to put one of the aerotec reloadable motors in a 6oz. version of my
36" delta wing.
His motor would put his 7oz. plane to over 1000 ft.
The motor can be configured with different nozzles and amounts of fuel.
He had
Has anyone heard from Tim Cone?
I have emailed a few times and not had any luck, does
he ave a new email address?
Mark Mech
[EMAIL PROTECTED]
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send "subscribe" and
"unsubscribe" requests to [EMAIL PROTECTED]
I accidently got 2 astro .010 brushless motors (mighty micro) I only ordered
1 so the other one is for sale for my cost + shipping.
It is $85.00 and the shipping will be $3.80 for priority mail.
They are normally about $100.00, there isn't much mark up on them.
It comes pre wired with the
I have been using a similar hinge method for about 3 years, I can't remember
if someone showed it to me or if it evolved from the "both surface tape"
method where you fold the surface over the wing and offset the hinge.
I space the aileron about 3/16" from the stationary surface and tape both
Hello RCSE'rs,
I just put up the first version of my international EPP materials list at:
www.aerofoam.com/materials.html
Please let me know if it shows up ok on different browsers etc.
I also just had to migrate my entire site to another server, so let me know
if any problems exist!
If you have
Boy, you're not kidding! That amount will more than pay for my Commercial
Glider license
So, you will be qualified for ...troop transport?
Mark Mech
[EMAIL PROTECTED]
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send "subscribe" and
Does anyone know how many cells it takes to run the tiny Hobby Shack B2
motors? what size cells for reasonable times?
Mark Mech
[EMAIL PROTECTED]
www.aerofoam.com
RCSE-List facilities provided by Model Airplane News. Send "subscribe" and
"unsubscribe" requests to [EMAIL
Here is the forecast for North Richland Hills, TX, zip code 76180, which
is
where I normally fly. You can substitute YOUR ZIP CODE:
http://www.weather.com/weather/hourbyhour/76180
This is a very cool feature, I book marked that site.
I have been using this one:
It is a wall filler compound like drywall mud, but the light weight stuff is
"silicon borate" it comes in a small tub and is water soluble.
You can see it being used to fill voids and mount servos on my Pico Jet
Modification page at: http://www.aerofoam.com/PicoJet.htm
I am compiling a list of
I was seaching the net for lithium batts last night and found that the
lithium polymers are in production and available for Nokia cell phones.
Not cheap, $89 for 3.7v cell that is about 600mah and weighs less than 10
grams.
There are a number of free plans for chargers that would only cost $10 to
Comes in a can a little taller and narrower than a soup can, sorta like a
small tennis ball can. You can find it at most hardware stores. I've
found
it at Ace Hardware, Walmart, Home Depot and LumberJack. Get the dip stuff,
the spray is ineffective and messy.
This stuff can be thinned or
UPS has gotten weird on large shipments.
It is because there is so much e-commerce with small package shipping.
UPS now looks at a large package and says, Hmmm I could get 9-$6.00 packages
in the same space that the large package takes up, so I should charge
$54.00 to ship the large package!
Maybe that's the eway
to go.although it would only be a matter of time before someone puts
together a Tip Launch Micro ;-)
Hopefully inexpensive 3 gram servos will become available in the near
futurelets hope :-)
They have, it's called a Noseeum or a Red Herring!
They both side
What about a sort of micro cross-country paradigm in which the overall
site
conditions must be artfully used to get one's glider to show up at a
series
of checkpoints?
It's called Handlaunch Golf! and they are playing today at the SWC
Scobie is right about new formats in my opinion.
I
You can still turn it on to check the radio environment, then shut it off
and do a proper start before flying.
Mark Mech
[EMAIL PROTECTED]
www.aerofoam.com
- Original Message -
From: "Regis White" [EMAIL PROTECTED]
To: "YK Chan" [EMAIL PROTECTED]; "RCSE" [EMAIL PROTECTED]
a fix for
rejuvenating a battery that had sulfated. The fix is to charge the
battery
with a constant current of C/20 for 24 hours
I deal with this on the main bank for my boat. It is 125ah
All lead acid batteries need a high voltage/current charge occasionally to
burn off the sulfate, on the
1 - 100 of 153 matches
Mail list logo