That describes a bridge or switch. A switch is
basically a multi-port bridge with advanced features.
A bridge just tracks port to MAC address; same for
basic switches. Advanced switches with layer 3/4
functions may track port #s as well.
A managed or smart hub lets you assign a network
address
This feature was introduced in 12.1(3)T.
12.1.6 mainline does not include T features. The
12.1.x mainline features were stopped at 12.0(7)T
basically.
--- Chad Humphries <[EMAIL PROTECTED]> wrote:
> I know that newer releases of the IOS allow a cisco
> router to act as a DHCP
> client and get it
The LightStream is Cisco's ATM Switch and good. It's
pricy though and may be hard to find.
IBM. I'm familiar with the MSS products (don't know
part # but it is 82xx.. may be 8285). The MSS were
OEM'd from Xylan. IBM OEM'd some of their switches to.
The MSS has a very cryptic configuration.
The
I don't have the link handy, but there are different
flash types on Cisco routers. Some don't allow you to
squeeze the flash to regain space, others do. I'll see
if I can find the link (I had it bookmarked on my work
PC).
I also question why you can delete if you can't
squeeze, but did find a us
The 144.20.0.0 network is not on router B so won't be
advertised. You can put it under the OSPF process but
it isn't going to do anything with that network
because it doesn't exist on that router at this time.
If it did, it would announce it.
If router B has a static route to 144.20.0.0 then you
Some suggestions.
Make sure the ISDN link works first by not placing
backup interface commands in the config. Just ping the
remote dialer interface IP and see if it is succesful.
If its not theres a config issue. Once you know the
dialer connection works then place the backup
interface command on
the second null0
> statement???
>
> Confused...(but thick enough to be happy)
>
> steve
>
> >From: "Erick B." <[EMAIL PROTECTED]>
> >Reply-To: "Erick B." <[EMAIL PROTECTED]>
> >To: Jon Kuhn <[EMAIL PROTECTED]>,
> "
You can get 1 port FE NMs for 36xx series. The 3662
has 2 10/100s in the base plus 6 slots.
The 2621 and 2651 have 2 10/100 ports in the base. No
modules though.
Or you can look at a layer 3 switch w/routing
capabilities (might be cheaper).
--- Jason Baker <[EMAIL PROTECTED]> wrote:
> nope FE
Windows: www.klever.net/kin (look for PumpKIN)
Also, Cisco and 3Com have free TFTP servers.
Linux: You need to enable the TFTP service. Depending
on the distro you have it may be there or not. You can
download a tftp daemon too.
--- "Sim, CT (Chee Tong)"
<[EMAIL PROTECTED]> wrote:
> H
I would say it will always go through, since null0 is
always up. The route-map will perform the actions
specified if the match conditions are all true. The
second null0 is a second interface to match against if
first one is down/unavailabe.
if you had:
route-map test perm 10
match interface s0
I'm not familiar with tcpdump output to well, what are
these IP address's for (router, pc, etc)
212.137.64.1 , 212.137.46.9 , 146.135.27.10
Can you provide a sanitized config along with a copy
of 'show ip route' and description of topology? It
could be a ip classless or classful issue perhaps o
That works for me...
--- "Kevin L. Kultgen" <[EMAIL PROTECTED]> wrote:
> Thanx, I'll let ya know if it doesn't work. No news
> is good news.
>
> Kevin L. Kultgen
>
> - Original Message -
> From: ""Erick B."" <[EMAI
Here ya go... adjust as necessary. There are similar
examples on cisco.com.
ip nat pool backup 10.10.10.6 10.10.10.6 netmask
255.255.255.0
ip nat pool primary 2.2.2.10 2.2.2.20 netmask
255.255.255.0
ip nat inside source route-map backup pool backup
ip nat inside source route-map primary pool prim
PPP uses magic numbers to detect loops. You'll see
warnings about receiving your magic #, etc if it
detects a loop. The magic number is a optional feature
though and every vendor doesn't use it or have it
enabled by default.
If using BayRS's 'Wellfleet Standard' which is their
implementation of H
Well, you have port-based VLANs and protocol-based
VLANs.
A switch/bridge builds a MAC address table (CAM) and
association MAC address's with a port. So, within the
switch arch. they extend these tables for VLAN
membership(s).
Lets say ports 1-5 are in VLAN 1 and 6-12 are in VLAN
2. So any MAC a
Looks like the image on flash went corrupt, or the
flash simm did. Try setting it up for a TFTP boot. If
you can get it to boot off TFTP erase the flash and
squeeze it and try putting a new image on the flash.
--- "Stull, Cory" <[EMAIL PROTECTED]> wrote:
> Has anyone seen this below error message
0 handy to try. This isn't going to
solve your problem but would be interesting to see
result.
Erick
--- "Erick B." <[EMAIL PROTECTED]> wrote:
> > %Error: This platform does not support relocatable
> > images
>
> It is erroring because of the above. Look over
ate: Sun, 18 Feb 2001 16:10:59 -0600
> Message-ID:
>
<[EMAIL PROTECTED]>
> X-Priority: 3 (Normal)
> X-MSMail-Priority: Normal
> X-Mailer: Microsoft Outlook IMO, Build 9.0.2416
> (9.0.2910.0)
> X-MimeOLE: Produced By Microsoft MimeOLE
> V5.00.2919.6700
> Importance: Norm
server local so ip-helper wasn't
needed.
If you search on cisco.com for HSRP and IP-helper
you'll get a document on UDP Flooding which involves
bridge-groups and using spanning-tree to block.
Erick
--- Bob Vance <[EMAIL PROTECTED]> wrote:
> I was told this in another venue:
It looks like the c2500 image you have is a
relocatable image, and the 4000 doesn't support
relocatable images. A relocatable image is one that
can be a different file # on flash. A non-relocatable
image has to be file 1. The 4500 is newer then the
4000 so may support relocatable images; this may
Hi,
I'm not sure how to calculate it for 4 seconds, but
all the documentation and examples I've seen explain
Bc (Commited burst) as bc = 1/8 / line access rate,
where 1/8 is the time period for a one second period
which is a common time period from my understanding.
Example:
line access rate: 6
Windump, tethereal (part of ethereal), probably a few
more libpcap/winpcap based apps.
--- [EMAIL PROTECTED] wrote:
> Hello,
>
> Is somebody know a command line sniffer for windows
> NT ?
__
Do You Yahoo!?
Get personalized email addresses from Ya
ip default-gateway works if ip routing is disabled and
the router is basically a host on the network like
your PCs, etc. You would turn IP routing off (no ip
routing) to bridge all traffic for example.
Using ip default-network would let you propagate a
route via IGRP/EIGRP or RIP to a neighbor ro
ave been having some problems with Multilink PPP
> recently. We have used
> Virtual-Template but have found that you can only
> have 1 Virtual-Template
> per Router (7507 in this case).
>
> Karl
>
> -Original Message-
> From: Erick B. [mailto:[EMAIL PROTECTED]]
> S
So, wheres the URL or info on 'Cisco Space Phones' ?
--- Arthur Simplina <[EMAIL PROTECTED]> wrote:
> This is COOL!!!
>
> >Received this today from my inside sales manager.
> >
> >Though you "might" consider blowing your own horn -
> it is still cool.
> >
> >Kevin Wigle
___
It will if they both have different IP subnets, thus
the floating route has it's own next hop.
If you want to go further you can use route-maps and
do policy routing. If PVC1 was down you could match on
the sub interface that was up and change the next hop.
Same for other PVC...
Why are you back
The default configuration, will have all the physical
interfaces shutdown (serial, ethernet, etc). To make
the interface active you must go into configuration
mode and put 'no shutdown' under the interface.
New routers or routers without a local configuration
or image file might have physical in
You can use the interface multilink feature to tie
serial interfaces together into one circuit. This is
fairly recent feature, mid 12.xT somewhere abouts.
multilink-group does not work on DDR interfaces. Look
into multilink virtual-template to do serial & ddr but
virtual-template is for inbound ca
== main/shared
HTH, Erick
--- David Tran <[EMAIL PROTECTED]> wrote:
> Hi Everyone,
> I have a cisco router 2620 that was running fine
> until Sunday when I =
> decided to upgrade the router=20
> with a new IOS. The new IOS image is specifically
> for cisco2610-2621. =
>
P the image back down.
I'm not sure why it lets you mark files for deletion
if you have to erase flash to regain space.
I can't find the cisco page on this at moment, but do
have it bookmarked on my other PC. I'll follow up with
the URL tomorrow.
Erick
--- "Roberts, Timothy&q
I get the best results w/USRs by setting them to dumb
mode, auto-answer, echo off, and default factory
settings. The jumpers are on the back edge or bottom
on the USRs depending on model. Newer ones are on
back. There should be a little chart on bottom with
what each DIP switch is for.
This way t
Hi,
You want to look into policy routing and route-maps on
cisco.com. Plenty of docs on the subject. You will
need two route-map sequences. One to match on www and
set next hop to R3 and the other to set next hop for
all other traffic to R2.
--- A Mateen <[EMAIL PROTECTED]> wrote:
> Hi !
>
> I
www.ethereal.com
It's free and decent for LAN/Ethernet stuff. If you're
looking for WAN, ATM, etc then you'll need to look at
commericial products such as Sniffer Pro.
--- Paul Werner <[EMAIL PROTECTED]> wrote:
>
> >Can someone recommend a good WindowsME
> sniffer?
>
> Well, I am not su
Why do you need a ethernet loopback plug? I've never
heard of or tried crossing the wires on a cable. Don't
know what would happen. Use caution. It may not even
come up or you might get a ton of collisions or
smoke... which reminds me of a graphic I have. :)
http://erickbe.home.dhs.org/etherkille
You're right.
--- John Neiberger <[EMAIL PROTECTED]> wrote:
> Actually, I believe that a static route pointing to
> a next hop has an AD of
> 1, but a static route pointing to an interface shows
> as directly connected
> and has an AD of 0.
>
> I just tested this to be sure, but someone else
>
t
prefer SM for major changes for compatibility reasons.
Erick
--- "Bradley J. Wilson" <[EMAIL PROTECTED]>
wrote:
> Don't forget that you may have another excellent
> configuration tool at your
> fingertips - the BCC (Bay Command Console), despite
> its relative
x.x.x is the instance. Just put the stuff
after the = in the get/set commands.
If you need assistance let me know. I'm in a rush to
get someplace right now so writing this real quick.
Erick
> >Wish I could help but I haven't touched a Bay in
> years, do you know how to
>
It's called Circuitless IP.
Protocols -> Circuitless IP.
You can only have one per router however and can
enable RIP, OSPF, etc for it.
--- Brian Lodwick <[EMAIL PROTECTED]> wrote:
> Anybody know how to configure a loopback interface
> on a Bay router?
>
> >>>Brian
With a TFTP server application.
PumpKIN is my favorite. Nice and small and gets job
done. www.klever.net/kin. Read the story :) They also
make some other nifty apps.
--- Turfis <[EMAIL PROTECTED]> wrote:
> How do you setup a WindowsME laptop as a TFTP server
> so that you can
> upload/download C
I use Sniffer Pro and Ethereal often. I like both of
them. Sniffer Pro supports alot more and Ethereal is
free and does a decent job at LAN/Ethernet traffic.
Ethereal also can decode application packets for
applications like Yahoo Messenger, AIM, Quake, ICQ,
etc which can be useful. This is avai
Other vendors (Nortel/Bay) support multiple spanning
tree groups on 802.1q as well. I think each
implementation is propiertary at moment. I heard
something about the IEEE working on a updated 802.1q
standard but I don't know where that stands today.
Anyone know?
I haven't tried Cisco 802.1q w/mu
What type of tunnel? I'm presuming some sort of VPN
tunnel. Sure you can. Set one end up as a server and
the other as a client.
Check out www.bigdig.com for cool pictures of tunnel
making :)
--- "N.Anand" <[EMAIL PROTECTED]> wrote:
> Can we create tunnel between 2 hosts without the
> help of isp
Since your pinging from the same router that this IP
resides on the access-list doesn't come into play.
Traffic flowing through that interface will be looked
at against the access-list but not traffic sourced
from the router, unless you set up a local policy
route.
If you have a static route rout
Use an access-list + access-group to permit only the
stations that need to manage the router.
You can't get rid of the directly connected routes
unless you remove IP from the interface. If the IP
network is entering the routing table on another
router then you have this network in a routing proce
we limit the amount of time a process level activity
can hold onto CPU in case we were process switching
voice traffic. otherwise voice quality is going to
suffer.
HTH, Erick
--- Hugo <[EMAIL PROTECTED]> wrote:
> Flem Hi,
> If you do not specify a process-max-time does that
> How
> would that explain what happened when you ran a
> "whois" on microsoft.com? Did anyone else see
> that?!?! It was pretty funny. -- about 15 lines of
> hacker orgs and comments about MS.
>
> A more frightening possibilitydid someone hack
> the
Look into the traffic-shape command (GTS).
int e0
traffic-shape ...
--- dovelet <[EMAIL PROTECTED]> wrote:
> Hi all,
>
> Is there any ways to limit the speed of a switch or
> router's ethernet port?
> Example, limit the max. speed of an ethernet port to
> 3Mbps.
The 2503 and 2522 are S/T. Usually on U interfaces,
the interface has 'ISDN U' or similar. Most of the
older routers are S/T but some may be U. It is
sometimes hard to find if something is S/T or U in
some cisco docs. Older docs say the port is ISDN BRI
only. On newer docs I've read they mention t
http://www.microsoft.com/info/siteaccess.htm
Microsoft Explains Site Access Issues
On Tuesday evening and Wednesday, many Microsoft
customers had difficulty accessing the company's Web
sites. The cause has been determined, and the issue is
resolved.
At 6:30 p.m. Tuesday (PST), a Microsoft tech
they
can be worked out.
OSPF Global:
5) On Bay the router ID is the first OSPF interface
configured on the router. You may want to modify this
or create a circuitless IP interface (loopback
interface on cisco).
Good Luck!! Erick
--- [EMAIL PROTECTED] wrote:
> Hello everyone. I have a projec
Hi,
First of all, this isn't a problem with cisco TAC.
They assisted you and dispatched hardware in a timely
manner. This is a problem with damage during shipping
or possibly defective units from the warehouse or
supplier used. I don't work for them but do know
sometimes that companies use other
> Plus routing of packets is done more quickly when
> done at the Switch level rather than having to go
> through the router for every packet.
All of this depends on the architecure of the
router/switch/software/etc. Some devices depend
heavily on 1 processor for everything the box can do.
Other
133379
41 78 0
--- [EMAIL PROTECTED] wrote:
> Erick,
> Thanks for passing on the question.
>
> sh is act doesn't help much either.
>
> router1#sh is act
>
OSPF will run on LAN, WAN, loopbacks, dialer, tunnel,
etc interfaces.
--- Charles Paver <[EMAIL PROTECTED]> wrote:
> Hi. Was wondering what interface i could or would
> put
> ospf on, for testing in a home lab environment!
> Such
> as, can I run ospf from eth0 to serial1 with 2
> different ro
Hi,
Have you tried 'show isdn act' ? I haven't done it on
a AS5300 but that shows a listing of active calls with
phone #, time up, idle time remaining, etc.
I also asked your question on the Cisco-NAS mailing
list which is more access-server related.
--- [EMAIL PROTECTED] wrote:
> In IOS 11.2,
Applications usually have a default/well-known
multicast group address they use. This may be
configurable depending on the app. Similar to port
numbers, most people use the defaults (80 for http, 23
for telnet, etc) but some people change them. If
someone changes the multicast group address from t
I defiantly make the customer aware of it and
have them correct it.
> Priscilla
Erick
__
Do You Yahoo!?
Get email at your own domain with Yahoo! Mail.
http://personal.mail.yahoo.com/
_
FAQ, list archives, and s
done/said.
Erick
--- Kevin Wigle <[EMAIL PROTECTED]> wrote:
> I don't think its so fishy and I don't think Cisco
> could be faulted in any way.
>
> My reading is that the "guy" was working with Cisco
> on a problem.
>
> Therefore this "guy"
I don't understand how companys can have main network
equipment (routers, etc) accessible over the internet
with telnet (and other mgmt services) running *with*
no passwords or filters. I see it on a regular
occurance.
--- Priscilla Oppenheimer <[EMAIL PROTECTED]> wrote:
> At 10:31 PM 1/17/01, J
router#term no mon
--- Frank <[EMAIL PROTECTED]> wrote:
> when i run "terminal monitor",i can see the debug
> info and some alarm
> messages
> from my console and vty terminal,but could you tell
> me how to disable it?
>
> cisco#no terminal monitor
> ^
> % Invalid input detected at '^'
unky stuff between different boxes. Even though
there are standards, everyone implements them in a
slightly different manner so there may be things you
need to tweak to get it optimized.
HTH, Erick
CCNP-Security, NNCSE,
CCIE attempt 2 soon
--- "Fowler, Joey" <[EMAIL PROTECTED]> wro
> even though it's not quite conforming to spec.
>
> -Brant.
>
>
> -Original Message-
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED]]On Behalf Of
> Erick B.
> Sent: Wednesday, January 10, 2001 1:44 PM
> To: Steve Linney; [EMAIL PROTECTED]
> Subject
I read somewhere that they are working on revising the
802.1q standard to support per-vlan STPs and it's
based on Cisco's per vlan STP. Not sure what the
current status is. You could turn off STP to avoid
this I think (haven't tried) if your network layout
doesn't have any loops, etc. Of course, i
Hi,
VTP is a Cisco propiertary method of automatically
learning about other VLANs in the network dynamically.
It is not supported on the 3Com SS 1100.
Look at the docs at support.3com.com. The SS-1100 does
support 802.1q which is a standard VLAN trunking
protocol supported by many vendors. You
Here ya go. No pinouts in PDF though or on their
website from what I saw. Might have to give them a
call. Thee PDF saids the interface is selectable so
maybe it's simple and you need to just change the
setting over to RS-449 instead of one of the others.
http://www.rainbow.com/mykoweb/kiv7.pdf
-
Most Frame relay connections go through some
telco/frame provider and some bigger organizations
have their own frame infrastructure. I'm not aware of
any security measures at the frame layer.
As for securing the information, you can encrypt at
layer 3. Most financial software these days has
encr
What are you asking - it's not that clear.
Anyway, HSRP is Cisco propiertary and will not work on
a Bay switch (use VRRP). If you have 2 Cisco devices
w/HSRP plugged into a Bay switch or hub that shouldn't
be a problem since the HSRP packets should just pass
through the switch. There was a code i
This really comes down to network design.
Lets say you have a couple devices doing HSRP and you
want half of the users to use 1 IP address and the
other half to use another IP address for their default
gateway. The HSRP device configured for both groups is
shared by groups of users. If the router
What problems are you having with the inactivity
timers? I'd recommend leaving them at default on the
Bay unless there is a problem involving them. Do you
have any Bay log entries stating a problem that you
can show me? I would change the OSPF MTU size on the
Bay interface from 1 (the default) to
Interesting. Have you tried to make the connects
regular ports (not trunks) and disable all autoneg
(trunk, port channel, duplex, speed, etc). I realize
that you may not be able to do a non-trunk test easily
but if you can that would narrow the problem down
further to a trunking issue or not. I ra
ping".
If you have a extra router with a BRI interface try
this ISDN circuit in that router to eliminate a
possible hardware problem perhaps. What IOS version
and model of router is this?
Erick
--- Gareth Hinton <[EMAIL PROTECTED]> wrote:
> Hi all,
>
> Thanks for the respo
> > >
> > > > Has anybody experienced an ISDN BRI "going to
> > > sleep".
> > > > After periods of inactivity, the layer 2
> status is
> > > not shown as active and
> > > > incoming calls cannot be received.
> > >
ut is there any
> > workaround, or is there some form of keepalive
> which is not default. Switch
> > is basic-net3.
> > Config is a real basic one used successfully in
> many other locations.
=
-
Erick B | [EMAIL PROTECTED]
http://erickb
ch as IP in this instance.
=
-----
Erick B | [EMAIL PROTECTED]
http://erickbe.home.dhs.org
-
__
Do You Yahoo!?
Yahoo! Shopping - Thousands of Stores. Millions of Products.
Kevin and group,
Here is the answer.
10.0 - EIGRP network command introduced
12.0(4)T - The network-mask argument was added
Here's the URL - watch the wrap.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/ip_r/iprprt2/1rdeigrp.htm#xtocid1405116
--- xndr <[EMAIL PROTEC
The 2503 BRI interface is S/T. On most of the Cisco
gear that I have seen with U interfaces it is labeled
"ISDN U" or similar.
Heres output from a Cisco 800 w/12.1(5)T code:
show int bri0
BRI0 is administratively down, line protocol is down
Hardware is BRI with U interface and POTS
2620
7;t the
> deciding factor.
I agree. I work in a multi-vendor TAC-like environment
and have seen some other vendor tech-support groups.
It also depends on who you get working with you. I get
good+bad support from the vendors I need to work with
depending on what it is.
=
-/--
They are on the CCIE R/S Equipment list and fair game.
The 4000 series routers are still being used today and
are solid performers even if they are old. 12.x IOS is
available for them if you have proper amount of DRAM
and Flash to support 12.x, Enterprise feature sets,
etc.
All the newer hardwa
orkstation (the TFTP server) and it did not work!
>
> Looks like my router was smart enough to figure out
> I was copying junk :)
>
> Cheers,
>
> Pierre
>
> -Original Message-
> From: Erick B. [mailto:[EMAIL PROTECTED]]
> Sent: Monday, December 11, 2000
Here's some pastes from a Cisco 800 when putting a
non-Cisco 800 file on the flash.
psychoticindustries.org#copy tftp flash
Address or name of remote host []? pc
Source filename []? geeks.gif
Destination filename [geeks.gif]?
Accessing tftp://pc/geeks.gif...
Loading geeks.gif from 192.168.1.50 (v
Pierre, Thanks for sharing the results with us. That
is useful information.
--- Pierre-Alex <[EMAIL PROTECTED]> wrote:
>
> Through trial and error, I have found that you
> cannot copy the image of a
> Cisco2513 (c2500-js-l_112-17.bin) to the flash of a
> Cisco 4000 (the TFTP
> Server). (I have t
The tftp-server command can only serve up files that
exist on the routers flash somewhere. If you do a
'show flash' and see the filename listed you can serve
it. Best bet is to do a 'show flash' and copy the
filename into clipboard so you can paste it on copy
command, etc and have right spelling.
tftp-server flash:filename
This will make the file's available to be TFTP'd off
this Cisco router from another device. IOS doesn't
allow a way to just TFTP any file to the flash from
remote that I know of. You need to use the copy tftp
command from the CLI to put files on the flash. This
is for
It depends on if Chad is driving the truck. :)
> Has anyone figured out the ballots-per-second (bps)
> transmission rate for the ballots that travelled in
> a Ryder truck from Palm Beach County to Tallahassee?
Bits travel around alot at high speed and there have
been sightings of swinging bits,
olks
interested.
--- "Erick B." <[EMAIL PROTECTED]> wrote:
> You need to get a USB to DB9 cable.
>
> http://www.pcwebshopper.com/bafusbtoserd.html
> $25
>
>
http://store.yahoo.com/cablesonline/usbtorsdb9se.html
> $39
>
> --- ERIC BRATAGER <[EMAIL PROTE
You need to get a USB to DB9 cable.
http://www.pcwebshopper.com/bafusbtoserd.html
$25
http://store.yahoo.com/cablesonline/usbtorsdb9se.html
$39
--- ERIC BRATAGER <[EMAIL PROTECTED]> wrote:
> If a laptop only has USB ports, what is the best way
> to connect to the
> console port? Is there any
If you remove the router ospf configuration and paste
it back, OSPF will restart with a new router ID if you
have a new high IP address. You can only do this in a
test/non-production network environment though. I've
done this before in my labs because it is faster then
waiting for the router to re
While browsing through the new features in recent
releases I found something very useful that will speed
up our config making/changing sessions.
http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t5/range.htm
Router(config-if)# interface range fastethernet 5/1 -
5,
It's on the equipment list and it is fair game (from
experience in SJ).
If you review the docs on cisco.com on configuration,
etc that should provide enough information on how the
device operates and is configured.
--- Tim Ross <[EMAIL PROTECTED]> wrote:
> Is a 3920 still used in the CCIE Lab
If you look at the interface input stats for s0 there
are input errors, CRC errors, framing errors,
overruns, etc. Clear the counters if this has been up
awhile, and see if those values increase still. If
they do have the line looked at. This is a physical
layer problem. If you want to make sure i
; route. I.e whenever any interface bounce..
> regardless of the OSPF Router ID.
> The difference is probably in terms of the amount of
> "data" being sent.. but
> definitely a covergence would occur..
>
>
>
> - Original Message -
> From: "Er
unless you want to
reach that from another device.
I hope this clears things up... it's late so I hope my
explanation makes sense. :) If not, hit me for the
mistakes if your ever in Chicago area.
Erick B. - Prepping for attempt 2.
(Why am I still up at 6am?)
--- Chuck Larrieu <[EMA
I'm no expert here, but from my experience...
Alot of this depends on the forwarding
methoding/switching method (whatever x vendor calls
it) of a device as well as the end station. The end
stations are responsible for pieceing the packets back
together in the right order (going over multiple path
Change the ospf network type on the loopback to
multipoint.
--- Simon Hope <[EMAIL PROTECTED]> wrote:
> Hi Guys / Gals
>
> Does anyone know of a way to make OSPF advertise the
> loopback network
> instead of the host route?
>
> ie:
>
> int lo0
> ip add 213.166.24.161 255.255.255.240
>
> comes
ct by using an access-list. This
access-list doesn't block traffic from going across
the dialer interface once the interface is up -- to do
that use ip access-group on the interface.
I hope this clears things up. If not ask away.
Erick
--- BENO JACOB <[EMAIL PROTECTED]> wrote:
> hi,
&g
For OSPF, if no loopback address is configured OSPF
uses the highest IP address on the router being used.
This could be a WAN interface. You may be running OSPF
only on your Ethernet interface and not this WAN
interface OSPF is using for the router ID.
If the WAN interface bounces, it effects OS
d see collisions, late
collisions, alignment errors, etc.
As for this happening at 2-3pm, anything happening in
your network at that time (broadcast storm, network
backup, etc)? I'd do a sniffer trace and see what that
reveals.
As for DEC21140, thats the chipset used on the
Ethernet interfac
Try searching/looking at DJ Cases.
--- "Cthulu, CCIE Candidate"
<[EMAIL PROTECTED]> wrote:
> Hi, all,
>
> Y'all recall that I posted a few weeks ago for a
> router cabinet. Well, I
> got some good leads, and then my circumstances have
> changed...again. I
> will be spending alot of time in K
Your doing OSPF through a NAT translation? If you send
me your Cisco/Bay configs I can take a look at them.
Send me the log off the Bay as well (save log
) at TI/telnet/console prompt.
What version of code on the Bay? NAT can be the
problem here since theres a # of issues involved with
NAT and
Know your stuff. They grill ya pretty good on BGP,
OSPF, IS-IS, ATM, MPLS if your familiar with it, some
SONET/STS stuff and probably will hit on other
technolgies (Frame Relay, PPP, security, etc). Having
experience in a core/ISP backbone environment is a
plus. I interviewed with them awhile bac
201 - 300 of 380 matches
Mail list logo