Re: Frame Relay Switch [7:75019]
Hi, guys: Why not consider 2523 i/o 2522 ? In the hardware spec, Cisco 2523 is the same as 2522, all the difference is 2523 is Token-Ring based, In eBay, you could find out that R2523 is cheaper than R2522, For the cost issues, I would suggest the 2523. If the cost/price is not the issues, maybe you could consider 4500/4700M+ with NP-4Ts, 4500/4700 has more horsepower than 2522/2523... Wilson - Original Message - From: "Devraj, Prem" To: Sent: Tuesday, September 09, 2003 5:49 PM Subject: RE: Frame Relay Switch [7:75019] > Hi Larry, > > I want to connect 8 port for a LAB Scenario which I have. I was thinking of > buying a 2522, I was just wondering if anyone has any better ideas then > buying this 2522 > > Thanks > prem > > -Original Message- > From: Larry Letterman [mailto:[EMAIL PROTECTED] > Sent: 2003 9 9 14:27 > To: [EMAIL PROTECTED] > Subject: RE: Frame Relay Switch [7:75019] > > > You can use the routers back to back with the v.35 cables..CCO has > A write-up on back-back frame connections..or buy an 8 port serial > Router... > > > Larry Letterman > Cisco Systems > > > > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of > Devraj, Prem > Sent: Monday, September 08, 2003 8:09 PM > To: [EMAIL PROTECTED] > Subject: Frame Relay Switch [7:75019] > > > Hi All, > > I am trying to setup a Lab for my CCIE. I do not have a Frame relay > switch. And it seems to expensive to buy one. > Does anyone have any ideas for a cheaper version of a Frame relay > switch. > > My requirement is atleast 8 ports. A friend of mine told me it is > possible to use a ordinary switch (I have tones of them) and use that as > a Tunnel for Frame relay encapsulation. > > Any ideas or suggestions will be welcomed. > > Thanks > prem > > > > *** > Dresdner Kleinwort Wasserstein is the marketing name used > globally to represent the investment banking activities of > Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein > is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, Tokyo > Branch or Dresdner Bank AG, Tokyo Branch. If you have received this > e-mail in error or wish to read our e-mail disclaimer statement and > monitoring policy, please refer to > http://www.drkw.com/disc/email/ or contact the sender. > > *** > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > > *** > Dresdner Kleinwort Wasserstein is the marketing name used > globally to represent the investment banking activities of > Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein > is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, > Tokyo Branch or Dresdner Bank AG, Tokyo Branch. > If you have received this e-mail in error or wish to read our e-mail > disclaimer statement and monitoring policy, please refer to > http://www.drkw.com/disc/email/ or contact the sender. > *** > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html This email has been scanned for all viruses by the MessageLabs Email Security System. For more information on a proactive email security service working around the clock, around the globe, visit http://www.messagelabs.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=75170&t=75019 -- **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
RE: Frame Relay Switch [7:75019]
I share my idea with you blow: Please application 2 ISDN lines and buy 2 ISDN modems, in china, you only need to pay RMB 50 per month for the lines, so cheap. Good luck! Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=75139&t=75019 -- **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Re: Frame Relay Switch [7:75019]
If you want to do more than j/a frame switch, than a 7000 would be ideal. Fast ethernet, atm, and frame-relay switch all in one. - Original Message - From: "Devraj, Prem" To: Sent: Tuesday, September 09, 2003 4:49 AM Subject: RE: Frame Relay Switch [7:75019] > Hi Larry, > > I want to connect 8 port for a LAB Scenario which I have. I was thinking of > buying a 2522, I was just wondering if anyone has any better ideas then > buying this 2522 > > Thanks > prem > > -Original Message- > From: Larry Letterman [mailto:[EMAIL PROTECTED] > Sent: 2003 9 9 14:27 > To: [EMAIL PROTECTED] > Subject: RE: Frame Relay Switch [7:75019] > > > You can use the routers back to back with the v.35 cables..CCO has > A write-up on back-back frame connections..or buy an 8 port serial > Router... > > > Larry Letterman > Cisco Systems > > > > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of > Devraj, Prem > Sent: Monday, September 08, 2003 8:09 PM > To: [EMAIL PROTECTED] > Subject: Frame Relay Switch [7:75019] > > > Hi All, > > I am trying to setup a Lab for my CCIE. I do not have a Frame relay > switch. And it seems to expensive to buy one. > Does anyone have any ideas for a cheaper version of a Frame relay > switch. > > My requirement is atleast 8 ports. A friend of mine told me it is > possible to use a ordinary switch (I have tones of them) and use that as > a Tunnel for Frame relay encapsulation. > > Any ideas or suggestions will be welcomed. > > Thanks > prem > > > > *** > Dresdner Kleinwort Wasserstein is the marketing name used > globally to represent the investment banking activities of > Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein > is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, Tokyo > Branch or Dresdner Bank AG, Tokyo Branch. If you have received this > e-mail in error or wish to read our e-mail disclaimer statement and > monitoring policy, please refer to > http://www.drkw.com/disc/email/ or contact the sender. > > *** > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > > *** > Dresdner Kleinwort Wasserstein is the marketing name used > globally to represent the investment banking activities of > Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein > is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, > Tokyo Branch or Dresdner Bank AG, Tokyo Branch. > If you have received this e-mail in error or wish to read our e-mail > disclaimer statement and monitoring policy, please refer to > http://www.drkw.com/disc/email/ or contact the sender. > *** > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=75097&t=75019 -- **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Re: Frame Relay Switch [7:75019]
Sure, you could use an older 7000 series router with 8 serial interfaces. You could also use a 2523. there is also a module for 26xx/36xx routers called an NM-8A/S which would also work. However the best solution is a 2522 or 2523. Old 7000 series routers are really big, extremely loud, and use lots of power. thanks, -Brad Ellis CCIE#5796 (R&S / Security) Network Learning Inc [EMAIL PROTECTED] www.optsys.net (Cisco hardware) ""Devraj, Prem"" wrote in message news:[EMAIL PROTECTED] > Hi Larry, > > I want to connect 8 port for a LAB Scenario which I have. I was thinking of > buying a 2522, I was just wondering if anyone has any better ideas then > buying this 2522 > > Thanks > prem > > -Original Message- > From: Larry Letterman [mailto:[EMAIL PROTECTED] > Sent: 2003 9 9 14:27 > To: [EMAIL PROTECTED] > Subject: RE: Frame Relay Switch [7:75019] > > > You can use the routers back to back with the v.35 cables..CCO has > A write-up on back-back frame connections..or buy an 8 port serial > Router... > > > Larry Letterman > Cisco Systems > > > > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of > Devraj, Prem > Sent: Monday, September 08, 2003 8:09 PM > To: [EMAIL PROTECTED] > Subject: Frame Relay Switch [7:75019] > > > Hi All, > > I am trying to setup a Lab for my CCIE. I do not have a Frame relay > switch. And it seems to expensive to buy one. > Does anyone have any ideas for a cheaper version of a Frame relay > switch. > > My requirement is atleast 8 ports. A friend of mine told me it is > possible to use a ordinary switch (I have tones of them) and use that as > a Tunnel for Frame relay encapsulation. > > Any ideas or suggestions will be welcomed. > > Thanks > prem > > > > *** > Dresdner Kleinwort Wasserstein is the marketing name used > globally to represent the investment banking activities of > Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein > is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, Tokyo > Branch or Dresdner Bank AG, Tokyo Branch. If you have received this > e-mail in error or wish to read our e-mail disclaimer statement and > monitoring policy, please refer to > http://www.drkw.com/disc/email/ or contact the sender. > > *** > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > > *** > Dresdner Kleinwort Wasserstein is the marketing name used > globally to represent the investment banking activities of > Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein > is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, > Tokyo Branch or Dresdner Bank AG, Tokyo Branch. > If you have received this e-mail in error or wish to read our e-mail > disclaimer statement and monitoring policy, please refer to > http://www.drkw.com/disc/email/ or contact the sender. > *** > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=75054&t=75019 -- **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Re: Frame Relay Switch [7:75019]
Hi, guys: Why not consider 2523 i/o 2522 ? In the hardware spec, Cisco 2523 is the same as 2522, all the difference is 2523 is Token-Ring based, In eBay, you could find out that R2523 is cheaper than R2522, For the cost issues, I would suggest the 2523. If the cost/price is not the issues, maybe you could consider 4500/4700M+ with NP-4Ts, 4500/4700 has more horsepower than 2522/2523... Wilson - Original Message - From: "Devraj, Prem" To: Sent: Tuesday, September 09, 2003 5:49 PM Subject: RE: Frame Relay Switch [7:75019] > Hi Larry, > > I want to connect 8 port for a LAB Scenario which I have. I was thinking of > buying a 2522, I was just wondering if anyone has any better ideas then > buying this 2522 > > Thanks > prem > > -Original Message- > From: Larry Letterman [mailto:[EMAIL PROTECTED] > Sent: 2003 9 9 14:27 > To: [EMAIL PROTECTED] > Subject: RE: Frame Relay Switch [7:75019] > > > You can use the routers back to back with the v.35 cables..CCO has > A write-up on back-back frame connections..or buy an 8 port serial > Router... > > > Larry Letterman > Cisco Systems > > > > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of > Devraj, Prem > Sent: Monday, September 08, 2003 8:09 PM > To: [EMAIL PROTECTED] > Subject: Frame Relay Switch [7:75019] > > > Hi All, > > I am trying to setup a Lab for my CCIE. I do not have a Frame relay > switch. And it seems to expensive to buy one. > Does anyone have any ideas for a cheaper version of a Frame relay > switch. > > My requirement is atleast 8 ports. A friend of mine told me it is > possible to use a ordinary switch (I have tones of them) and use that as > a Tunnel for Frame relay encapsulation. > > Any ideas or suggestions will be welcomed. > > Thanks > prem > > > > *** > Dresdner Kleinwort Wasserstein is the marketing name used > globally to represent the investment banking activities of > Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein > is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, Tokyo > Branch or Dresdner Bank AG, Tokyo Branch. If you have received this > e-mail in error or wish to read our e-mail disclaimer statement and > monitoring policy, please refer to > http://www.drkw.com/disc/email/ or contact the sender. > > *** > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > > *** > Dresdner Kleinwort Wasserstein is the marketing name used > globally to represent the investment banking activities of > Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein > is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, > Tokyo Branch or Dresdner Bank AG, Tokyo Branch. > If you have received this e-mail in error or wish to read our e-mail > disclaimer statement and monitoring policy, please refer to > http://www.drkw.com/disc/email/ or contact the sender. > *** > **Please support GroupStudy by purchasing from the GroupStudy Store: > http://shop.groupstudy.com > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=75063&t=75019 -- **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
RE: Frame Relay Switch [7:75019]
Hi Larry, I want to connect 8 port for a LAB Scenario which I have. I was thinking of buying a 2522, I was just wondering if anyone has any better ideas then buying this 2522 Thanks prem -Original Message- From: Larry Letterman [mailto:[EMAIL PROTECTED] Sent: 2003 9 9 14:27 To: [EMAIL PROTECTED] Subject: RE: Frame Relay Switch [7:75019] You can use the routers back to back with the v.35 cables..CCO has A write-up on back-back frame connections..or buy an 8 port serial Router... Larry Letterman Cisco Systems -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Devraj, Prem Sent: Monday, September 08, 2003 8:09 PM To: [EMAIL PROTECTED] Subject: Frame Relay Switch [7:75019] Hi All, I am trying to setup a Lab for my CCIE. I do not have a Frame relay switch. And it seems to expensive to buy one. Does anyone have any ideas for a cheaper version of a Frame relay switch. My requirement is atleast 8 ports. A friend of mine told me it is possible to use a ordinary switch (I have tones of them) and use that as a Tunnel for Frame relay encapsulation. Any ideas or suggestions will be welcomed. Thanks prem *** Dresdner Kleinwort Wasserstein is the marketing name used globally to represent the investment banking activities of Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, Tokyo Branch or Dresdner Bank AG, Tokyo Branch. If you have received this e-mail in error or wish to read our e-mail disclaimer statement and monitoring policy, please refer to http://www.drkw.com/disc/email/ or contact the sender. *** **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html *** Dresdner Kleinwort Wasserstein is the marketing name used globally to represent the investment banking activities of Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, Tokyo Branch or Dresdner Bank AG, Tokyo Branch. If you have received this e-mail in error or wish to read our e-mail disclaimer statement and monitoring policy, please refer to http://www.drkw.com/disc/email/ or contact the sender. *** Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=75045&t=75019 -- **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
RE: Frame Relay Switch [7:75019]
You can use the routers back to back with the v.35 cables..CCO has A write-up on back-back frame connections..or buy an 8 port serial Router... Larry Letterman Cisco Systems -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Devraj, Prem Sent: Monday, September 08, 2003 8:09 PM To: [EMAIL PROTECTED] Subject: Frame Relay Switch [7:75019] Hi All, I am trying to setup a Lab for my CCIE. I do not have a Frame relay switch. And it seems to expensive to buy one. Does anyone have any ideas for a cheaper version of a Frame relay switch. My requirement is atleast 8 ports. A friend of mine told me it is possible to use a ordinary switch (I have tones of them) and use that as a Tunnel for Frame relay encapsulation. Any ideas or suggestions will be welcomed. Thanks prem *** Dresdner Kleinwort Wasserstein is the marketing name used globally to represent the investment banking activities of Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, Tokyo Branch or Dresdner Bank AG, Tokyo Branch. If you have received this e-mail in error or wish to read our e-mail disclaimer statement and monitoring policy, please refer to http://www.drkw.com/disc/email/ or contact the sender. *** **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=75027&t=75019 -- **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
RE: Frame Relay Switch [7:75019]
You can get a 2522 with 10 port serial for around $500. Raj Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=75022&t=75019 -- **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Frame Relay Switch [7:75019]
Hi All, I am trying to setup a Lab for my CCIE. I do not have a Frame relay switch. And it seems to expensive to buy one. Does anyone have any ideas for a cheaper version of a Frame relay switch. My requirement is atleast 8 ports. A friend of mine told me it is possible to use a ordinary switch (I have tones of them) and use that as a Tunnel for Frame relay encapsulation. Any ideas or suggestions will be welcomed. Thanks prem *** Dresdner Kleinwort Wasserstein is the marketing name used globally to represent the investment banking activities of Dresdner Bank Group. In Japan, Dresdner Kleinwort Wasserstein is represented by Dresdner Kleinwort Wasserstein (Japan) Limited, Tokyo Branch or Dresdner Bank AG, Tokyo Branch. If you have received this e-mail in error or wish to read our e-mail disclaimer statement and monitoring policy, please refer to http://www.drkw.com/disc/email/ or contact the sender. *** Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=75019&t=75019 -- **Please support GroupStudy by purchasing from the GroupStudy Store: http://shop.groupstudy.com FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Re: Help making a frame relay switch [7:64224]
Figure 3: NM-4T, NM-4A/S, NM-8A/S, WIC-1T, WIC-1DSU-56K4 The NM-4T serial network module has four synchronous serial interfaces. The network module supports a total full-duplex throughput of 8 megabits per second (Mbps), which can be realized over one port (at 8 Mbps) or across all four ports (at 2 Mbps on each port). The NM-4T module in any network environment delivers very low price per port and provides higher performance than comparable third-party solutions. For instance, a small or medium-sized Internet service provider (ISP) with high serial density requirements may find this solution very cost-effective per subscriber. LEDs-Network module status indicator, five Status LEDs for each serial port, including data send/receive indication. Network interfaces-Four serial interfaces. Table 2 Cable Options2 for the 4T Network Module: Product Number Cable Type Cable Name Length Connector Type CAB-V35MT V.35 DTE T1/E1 10 ft Male CAB-V35FC V.35 DCE T1/E1 10 ft Female CAB-232MT EIA/TIA -232 DTE T1/E1 10 ft Male CAB-232FC EIA/TIA -232 DCE T1/E1 10 ft Female CAB-449MT EIA/TIA -449 DTE T1/E1 10 ft Male CAB-449FC EIA/TIA -449 DCE T1/E1 10 ft Female CAB-X21MT X.21 DTE T1/E1 10 ft Male CAB-X21FC X.21 DCE T1/E1 10 ft Female CAB-530MT EIA/TIA-530 DTE T1/E1 10 ft Male Larry Letterman Network Engineer Cisco Systems - Original Message - From: hepppy To: [EMAIL PROTECTED] Sent: Sunday, March 02, 2003 8:11 PM Subject: Help making a frame relay switch [7:64224] Hi all, Sorry for being Naive. I am interested in creating a lab with some 10 X 26xx routers. I need to create a frame realy switch. I am not sure what to use. I have seen a Lab a couple of months back which had 8 DB60 serial cables connected to the 26xx router. Now I don;t have one of those with me, hence was searching on the net to purchase one. And I found a Description of 8 port Asynch/Synch and 2 port serial. The question is Is Asynch port the same as serial ports. Can I connect DB60 back to back cables to Asynch ports. Any other suggestions or help to make this Frame realy switch will be appreciated Thanks to all... regds hepppy [GroupStudy removed an attachment of type image/gif which had a name of seral_d2.gif] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=64233&t=64224 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Help making a frame relay switch [7:64224]
""Mark W. Odette II"" wrote in message news:[EMAIL PROTECTED] > If I recall correctly, Asynch ports run at 115Kbps line rate (referred > to as 'low-speed serial ports'). can still use that setup as a frame switch. A certain rack rental place used a router with a bunch of async ports - maybe a 2522? just be sure to use a matching clock rate on the DCE side. > > The idea behind using such a piece of hardware in the 2600/3600 routers > is to make that specific router the "Terminal Server" to console into > all the other routers. > > You could also connect back-to-back asynchs, I suppose, but I've never > done it myself. > > > > -Original Message- > From: hepppy [mailto:[EMAIL PROTECTED] > Sent: Sunday, March 02, 2003 10:11 PM > To: [EMAIL PROTECTED] > Subject: Help making a frame relay switch [7:64224] > > Hi all, > > Sorry for being Naive. I am interested in creating a lab with some 10 X > 26xx > routers. I need to create a frame realy switch. I am not sure what to > use. I > have seen a Lab a couple of months back which had 8 DB60 serial cables > connected to the 26xx router. Now I don;t have one of those with me, > hence > was > searching on the net to purchase one. And I found a Description of 8 > port > Asynch/Synch and 2 port serial. The question is Is Asynch port the same > as > serial ports. Can I connect DB60 back to back cables to Asynch ports. > > Any other suggestions or help to make this Frame realy switch will be > appreciated > > Thanks to all... > > regds > hepppy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=64237&t=64224 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Help making a frame relay switch [7:64224]
If I recall correctly, Asynch ports run at 115Kbps line rate (referred to as 'low-speed serial ports'). The idea behind using such a piece of hardware in the 2600/3600 routers is to make that specific router the "Terminal Server" to console into all the other routers. You could also connect back-to-back asynchs, I suppose, but I've never done it myself. -Original Message- From: hepppy [mailto:[EMAIL PROTECTED] Sent: Sunday, March 02, 2003 10:11 PM To: [EMAIL PROTECTED] Subject: Help making a frame relay switch [7:64224] Hi all, Sorry for being Naive. I am interested in creating a lab with some 10 X 26xx routers. I need to create a frame realy switch. I am not sure what to use. I have seen a Lab a couple of months back which had 8 DB60 serial cables connected to the 26xx router. Now I don;t have one of those with me, hence was searching on the net to purchase one. And I found a Description of 8 port Asynch/Synch and 2 port serial. The question is Is Asynch port the same as serial ports. Can I connect DB60 back to back cables to Asynch ports. Any other suggestions or help to make this Frame realy switch will be appreciated Thanks to all... regds hepppy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=64234&t=64224 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Help making a frame relay switch [7:64224]
Hi all, Sorry for being Naive. I am interested in creating a lab with some 10 X 26xx routers. I need to create a frame realy switch. I am not sure what to use. I have seen a Lab a couple of months back which had 8 DB60 serial cables connected to the 26xx router. Now I don;t have one of those with me, hence was searching on the net to purchase one. And I found a Description of 8 port Asynch/Synch and 2 port serial. The question is Is Asynch port the same as serial ports. Can I connect DB60 back to back cables to Asynch ports. Any other suggestions or help to make this Frame realy switch will be appreciated Thanks to all... regds hepppy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=64224&t=64224 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
OT: Router as Frame Relay Switch - PVC types [7:53870]
anyone familiar with any nerd knobs when using a Cisco router as a frame-relay switch? My liberal use of the "?" has not revealed what I am looking for - to whit whether PVC type can be configured. I'm looking into frame relay QoS options, and my reading talks about PVC types ( FRF 3.1 or FRF 11 ) as if these are configurable. thanks. Chuck -- www.chuckslongroad.info like my web site? take the survey! Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=53870&t=53870 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: IPX EIGRP and Frame Relay switch [7:46626]
Realised that I needed to define the 'same' IPX network (7) on DTE Router E(DLCI 101) and DTE Router B (DLCI 102) They had different IPX network numbers. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=46692&t=46626 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: IPX EIGRP and Frame Relay switch [7:46626]
don't keep us in suspense. which error solved the problem? the missing clock rate on one of the serial interfaces? the network protocols on the frame relay interfaces? the no frame inverse NOVEL? all of the above? fair's fair. netiquette requires you fill us in. your realization will help others to learn. much appreciated. Chuck ""Karen Menpes"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Hi this issue has now been solved ! Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=46686&t=46626 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: IPX EIGRP and Frame Relay switch [7:46626]
Hi this issue has now been solved ! Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=46678&t=46626 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: IPX EIGRP and Frame Relay switch [7:46626]
The exact configs for the 3 routers are pasted in below. They are a little 'untidy'. FR Switch --- version 12.0 service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname A ! enable password 7 0458 ! ip subnet-zero clns net 01.0010.7b3c.0b38.00 clns routing ipx routing 000a.000a.000a ipx internal-network 10 frame-relay switching ! ! ! ! ! interface Loopback0 ip address 192.168.0.3 255.255.255.255 no ip directed-broadcast ! interface Loopback1 ip address 180.24.3.1 255.255.255.0 no ip directed-broadcast ! interface Loopback2 ip address 175.1.2.1 255.255.255.0 no ip directed-broadcast ! interface Loopback3 ip address 174.1.0.1 255.255.0.0 no ip directed-broadcast ! interface Loopback4 no ip address no ip directed-broadcast ! interface Loopback6 ip address 111.0.0.1 255.255.255.255 no ip directed-broadcast ! interface Loopback7 ip address 112.0.0.1 255.255.255.255 no ip directed-broadcast ! interface Loopback20 ip address 90.1.5.1 255.255.255.252 no ip directed-broadcast ! interface Loopback25 ip address 91.9.3.7 255.255.255.240 no ip directed-broadcast ! interface Loopback33 ip address 141.1.5.1 255.255.255.252 no ip directed-broadcast ! interface Loopback44 ip address 196.0.0.1 255.255.255.0 no ip directed-broadcast ! interface Loopback56 ip address 181.3.0.1 255.255.255.255 no ip directed-broadcast ! interface Loopback77 ip address 135.0.3.60 255.255.255.255 no ip directed-broadcast ! interface Ethernet0 ip address 192.168.4.2 255.255.255.0 no ip directed-broadcast ip ospf network broadcast ip ospf interface-retry 0 ! interface Ethernet1 no ip address no ip directed-broadcast shutdown ! interface Serial0 ip address 130.24.1.2 255.255.255.0 no ip directed-broadcast encapsulation frame-relay no ip mroute-cache ipx network 7 ipx update interval rip 120 ipx update interval sap 120 no fair-queue clockrate 64000 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 102 interface Serial1 101 ! interface Serial1 bandwidth 64000 ip address 129.64.2.2 255.255.255.0 no ip directed-broadcast encapsulation frame-relay ipx network 9 clockrate 64000 no frame-relay inverse-arp NOVELL 102 no frame-relay inverse-arp NOVELL 201 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 101 interface Serial0 102 ! interface Dialer1 no ip address no ip directed-broadcast no cdp enable ! autonomous-system 55 ! router rip network 112.0.0.0 network 130.24.0.0 network 141.0.0.0 network 141.1.0.0 distance 40 ! router igrp 1 network 90.0.0.0 network 111.0.0.0 network 130.24.0.0 network 131.64.0.0 network 175.1.0.0 network 196.0.0.0 ! router bgp 2 no synchronization network 180.24.3.0 mask 255.255.255.0 network 192.168.0.2 mask 255.255.255.255 network 192.168.0.3 mask 255.255.255.255 neighbor LOCAL peer-group neighbor LOCAL update-source Loopback0 neighbor 192.168.4.4 remote-as 2 ! ip classless ip route 90.0.0.0 255.0.0.0 Null0 200 ip route 90.0.0.0 255.0.0.0 Loopback0 200 ip route 90.1.5.1 255.255.255.255 Null0 200 ip route 192.168.0.4 255.255.255.255 Serial1 ip route 192.168.4.4 255.255.255.255 Serial1 ! access-list 3 permit 23.0.0.0 access-list 3 permit 27.0.0.0 access-list 3 permit 180.24.0.0 ! ! ! ipx router rip no network 7 no network 9 ! ! ipx sap 4 FSGETOUT FEED..7656.9862 451 1 ipx sap 4 FSKAREN FACE..6790.4598 451 1 ! tftp-server flash tftp-server flash: tftp-server flash:c2500-jos56i-l.120-9.bin ! line con 0 exec-timeout 0 0 transport input none line aux 0 exec-timeout 0 0 modem InOut modem autoconfigure discovery transport input all speed 1200 flowcontrol hardware line vty 0 4 password 7 0605 login ! end DTE Switch B Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime service password-encryption ! hostname B ! logging buffered 1 debugging enable password 7 121A ! ip subnet-zero clns routing ipx routing 000b.000b.000b ipx internal-network 20 ! ! ! ! ! interface Loopback0 ip address 192.168.0.1 255.255.255.255 no ip directed-broadcast ! interface Loopback1 ip address 160.5.128.129 255.255.255.128 no ip directed-broadcast ipx network 1 ! interface Loopback2 ip address 165.4.0.1 255.255.0.0 no ip directed-broadcast ! interface Loopback3 ip address 161.3.0.1 255.255.0.0 no ip directed-broadcast ! interface Loopback4 ip address 162.4.192.193 255.255.255.192 no ip directed-broadcast ! interface Loopback5 ip address 27.0.0.1 255.0.0.0 no ip directed-broadcast ! interface Loopback6 ip address 23.0.0.1 255.0.0.0 no ip directed-broadcast ! interface Loopback20 ip address 103.0.0.2 255.255.255.255 no ip directed-broadcast ! interface Loopback21 ip address 135.0.3.60 255.255.255.255 no ip directed-broadcast ip ospf interface-retry 0 ! interface Loopback30 no ip address no ip directed-broadcast ! interface Loopback56 ip address 190.50.1.2 255.255.255.252 no ip directed-br
Re: IPX EIGRP and Frame Relay switch [7:46626]
perhaps you have some configs you are willing to share? ""Karen Menpes"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Hi, > > I've seemed to have found a stange issue with IPX Eigrp when running it over > a Frame Relay setup. > > Using ver 12.0(9) of IOS. > > I can see the other router's IPX network when typing in the 'show > frame-relay map' command but can't get IPX Eigrp to establish an adjacency > at all. > > I've typed in all the necessary IPX networks into the IPX EIGRP router > config and subseqently taken those networks out of the IPX router setup. > > Also, on this 'exact' same frame relay network I never had an issue with > picking up IPX/RIP routes between the DTE routers about 10 mins prior to > setting up IPX EIGRP. I run debugs and it appears that there's very little > activity from IPX EIGRP. It also seems as the IPX EIGRP if it's totally dead > but is defintely configured ! Disabled and enabled IPX Routing and > re-established the IPX ROUTING identifier but no luck at all. > > It's a very simple Frame relay setup with 3 router's and one is the FR > switch. Each connection into the switch has it's own separate serial > interface so I wouldn't expect a split-horizon issue to be the cause of the > problem. > > > Any ideas as to why IPX EIGRP does not like Frame Relay but loves HDLC ? > > Karen Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=46628&t=46626 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
IPX EIGRP and Frame Relay switch [7:46626]
Hi, I've seemed to have found a stange issue with IPX Eigrp when running it over a Frame Relay setup. Using ver 12.0(9) of IOS. I can see the other router's IPX network when typing in the 'show frame-relay map' command but can't get IPX Eigrp to establish an adjacency at all. I've typed in all the necessary IPX networks into the IPX EIGRP router config and subseqently taken those networks out of the IPX router setup. Also, on this 'exact' same frame relay network I never had an issue with picking up IPX/RIP routes between the DTE routers about 10 mins prior to setting up IPX EIGRP. I run debugs and it appears that there's very little activity from IPX EIGRP. It also seems as the IPX EIGRP if it's totally dead but is defintely configured ! Disabled and enabled IPX Routing and re-established the IPX ROUTING identifier but no luck at all. It's a very simple Frame relay setup with 3 router's and one is the FR switch. Each connection into the switch has it's own separate serial interface so I wouldn't expect a split-horizon issue to be the cause of the problem. Any ideas as to why IPX EIGRP does not like Frame Relay but loves HDLC ? Karen Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=46626&t=46626 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: frame-relay switch [7:41899]
Very simple. You will need 3 routers, one router acting as the Frame-switch with atleast 2 serial/interfaces, and the other 2 routers are the remote sites, they need to have atleast 1 serial/interface each. You will also need two serial crossover cables DTE-DCE ends. Here is a basic configuration FRAMEswitch-router / Using serial 0 and serial 2 interfaces No service udp-small-servers no service tcp-small-servers frame-relay swithing DCE-end cable connects here frame-relay route 100 interface serial 2 101 interface serial 2 no ip address encapsulation frame-relay clock rate 19200 frame-relay lim-type ansi frame-relay intf-type DCE frame-relay route 101 interface serial 0 100 Router-A - DCE-end connects to the Frameswitch-router interface Serial1 ip address 192.1.1.1 255.255.255.0 encapsulation frame-relay frame-relay lmi-type ansi router rip network 192.1.1.0 Note: Commands to check frame-relay map and LMA signaling Show frame pvc show frame map show frame lmi Router-B DCE-end connects to the frameswitch-router interface Serial1 ip address 192.1.1.3 255.255.255.0 encapsulation frame-relay no ip mroute-cache frame-relay lmi-type ansi ip routing router rip network 192.1.1.0 Note: Again , Commands to check the frame-relay DLCI maps, and LMI signaling and PVC statuts Show frame pvc show frame map show frame lmi Ping your remote sites Hope this helps Jorge Rodriguez CCNA/CCNP/ CCIE Candidate [EMAIL PROTECTED] [EMAIL PROTECTED] [EMAIL PROTECTED] wrote: > Does anyone know how to connect and configure two (2) 2513 as a frame-relay > switch? Please send me the config file. > > mike > > > > - > Do You Yahoo!? > Yahoo! Tax Center - online filing with TurboTax Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=42061&t=41899 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: frame-relay switch [7:41899]
Very simple. You will need 3 routers, one router acting as the Frame-switch with atleast 2 serial/interfaces, and the other 2 routers are the remote sites, they need to have atleast 1 serial/interface each. You will also need two serial crossover cables DTE-DCE ends. Here is a basic configuration FRAMEswitch-router / Using serial 0 and serial 2 interfaces No service udp-small-servers no service tcp-small-servers frame-relay swithing DCE-end cable connects here frame-relay route 100 interface serial 2 101 interface serial 2 no ip address encapsulation frame-relay clock rate 19200 frame-relay lim-type ansi frame-relay intf-type DCE frame-relay route 101 interface serial 0 100 Router-A - DCE-end connects to the Frameswitch-router interface Serial1 ip address 192.1.1.1 255.255.255.0 encapsulation frame-relay frame-relay lmi-type ansi router rip network 192.1.1.0 Note: Commands to check frame-relay map and LMA signaling Show frame pvc show frame map show frame lmi Router-B DCE-end connects to the frameswitch-router interface Serial1 ip address 192.1.1.3 255.255.255.0 encapsulation frame-relay no ip mroute-cache frame-relay lmi-type ansi ip routing router rip network 192.1.1.0 Note: Again , Commands to check the frame-relay DLCI maps, and LMI signaling and PVC statuts Show frame pvc show frame map show frame lmi Ping your remote sites Hope this helps Jorge Rodriguez CCNA/CCNP/ CCIE Candidate [EMAIL PROTECTED] [EMAIL PROTECTED] [EMAIL PROTECTED] wrote: > Does anyone know how to connect and configure two (2) 2513 as a frame-relay > switch? Please send me the config file. > > mike > > > > - > Do You Yahoo!? > Yahoo! Tax Center - online filing with TurboTax Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=42059&t=41899 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: frame-relay switch [7:41899]
Very simple. You will need 3 routers, one router acting as the Frame-switch with atleast 2 serial/interfaces, and the other 2 routers are the remote sites, they need to have atleast 1 serial/interface each. You will also need two serial crossover cables DTE-DCE ends. Here is a basic configuration FRAMEswitch-router / Using serial 0 and serial 2 interfaces No service udp-small-servers no service tcp-small-servers frame-relay swithing DCE-end cable connects here frame-relay route 100 interface serial 2 101 interface serial 2 no ip address encapsulation frame-relay clock rate 19200 frame-relay lim-type ansi frame-relay intf-type DCE frame-relay route 101 interface serial 0 100 Router-A - DCE-end connects to the Frameswitch-router interface Serial1 ip address 192.1.1.1 255.255.255.0 encapsulation frame-relay frame-relay lmi-type ansi router rip network 192.1.1.0 Note: Commands to check frame-relay map and LMA signaling Show frame pvc show frame map show frame lmi Router-B DCE-end connects to the frameswitch-router interface Serial1 ip address 192.1.1.3 255.255.255.0 encapsulation frame-relay no ip mroute-cache frame-relay lmi-type ansi ip routing router rip network 192.1.1.0 Note: Again , Commands to check the frame-relay DLCI maps, and LMI signaling and PVC statuts Show frame pvc show frame map show frame lmi Ping your remote sites Hope this helps Jorge Rodriguez CCNA/CCNP/ CCIE Candidate [EMAIL PROTECTED] [EMAIL PROTECTED] [EMAIL PROTECTED] wrote: > Does anyone know how to connect and configure two (2) 2513 as a frame-relay > switch? Please send me the config file. > > mike > > > > - > Do You Yahoo!? > Yahoo! Tax Center - online filing with TurboTax Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=42058&t=41899 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: frame-relay switch [7:41899]
Very simple. You will need 3 routers, one router acting as the Frame-switch with atleast 2 serial/interfaces, and the other 2 routers are the remote sites, they need to have atleast 1 serial/interface each. You will also need two serial crossover cables DTE-DCE ends. Here is a basic configuration FRAMEswitch-router / Using serial 0 and serial 2 interfaces No service udp-small-servers no service tcp-small-servers frame-relay swithing DCE-end cable connects here frame-relay route 100 interface serial 2 101 interface serial 2 no ip address encapsulation frame-relay clock rate 19200 frame-relay lim-type ansi frame-relay intf-type DCE frame-relay route 101 interface serial 0 100 Router-A - DCE-end connects to the Frameswitch-router interface Serial1 ip address 192.1.1.1 255.255.255.0 encapsulation frame-relay frame-relay lmi-type ansi router rip network 192.1.1.0 Note: Commands to check frame-relay map and LMA signaling Show frame pvc show frame map show frame lmi Router-B DCE-end connects to the frameswitch-router interface Serial1 ip address 192.1.1.3 255.255.255.0 encapsulation frame-relay no ip mroute-cache frame-relay lmi-type ansi ip routing router rip network 192.1.1.0 Note: Again , Commands to check the frame-relay DLCI maps, and LMI signaling and PVC statuts Show frame pvc show frame map show frame lmi Ping your remote sites Hope this helps Jorge Rodriguez CCNA/CCNP/ CCIE Candidate [EMAIL PROTECTED] [EMAIL PROTECTED] [EMAIL PROTECTED] wrote: > Does anyone know how to connect and configure two (2) 2513 as a frame-relay > switch? Please send me the config file. > > mike > > > > - > Do You Yahoo!? > Yahoo! Tax Center - online filing with TurboTax Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=42057&t=41899 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: frame-relay switch [7:41899]
The Mc-Graw Hill BCRAN book has got step-by-step on this. Looks like Simer Mayo's post. -Sean. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=41961&t=41899 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: frame-relay switch [7:41899]
Hope this helps: On the Switch: FRswitch(config)#frame-relay switching FRswitch(config)#interface serial 0/0 FRswitch(config-if)#encapsulation frame-relay FRswitch(config-if)#frame-relay interface-type dce !---Frame Relay switches identify inbound frames by their DLCI. The DLCI is then referenced in a switching table to determine the outbound port. !---Configure a static route for each serial interface to define an end-to-end PVC: FRswitch(config)#interface serial 0/0 FRswitch(config-if)#frame-relay route 18 interface serial 0/1 17 FRswitch(config-if)#interface serial 0/1 FRswitch(config-if)#frame-relay route 16 interface serial 0/0 19 On router 1: RTR1(config)#interface serial 0/0 RTR1(config-if)#encapsulation frame-relay RTR1(config-if)#ip address 192.168.192.1 255.255.255.0 RTR1(config-if)#exit Specify the DLCI number on both routers. Simer -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] Sent: Thursday, April 18, 2002 5:17 PM To: [EMAIL PROTECTED] Subject: frame-relay switch [7:41899] Does anyone know how to connect and configure two (2) 2513 as a frame-relay switch? Please send me the config file. mike - Do You Yahoo!? Yahoo! Tax Center - online filing with TurboTax Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=41900&t=41899 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
frame-relay switch [7:41899]
Does anyone know how to connect and configure two (2) 2513 as a frame-relay switch? Please send me the config file. mike - Do You Yahoo!? Yahoo! Tax Center - online filing with TurboTax Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=41899&t=41899 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
aux - aux 2501-2501 frame relay switch [7:40026]
Hi group Someone posted sometime ago how to configure two 2501 to act as a frame relay switch by connecting them via the aux ports can someone please post the configuration again please. Thanks Steve Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=40026&t=40026 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: router to use as frame relay switch [7:32348]
Here is a snapshot of a 2600 running as a frame switch, you can do this with pretty much any router with multiple serial interfaces. Go to www.fatkid.com, they have some sample configs for frame relay switching on a router. You can also do a lookup on CCO for it. If you have trouble let us know. frame-relay switching ! ! voice-port 1/0/0 ! voice-port 1/0/1 ! voice-port 1/1/0 ! voice-port 1/1/1 ! ! ! ! interface FastEthernet0/0 no ip address no ip mroute-cache shutdown duplex auto speed auto ! interface Serial0/0 no ip address encapsulation frame-relay no ip mroute-cache no fair-queue clockrate 130 frame-relay intf-type dce frame-relay route 306 interface Serial0/3 603 ! interface FastEthernet0/1 no ip address no ip mroute-cache shutdown duplex auto speed auto ! interface Serial0/1 no ip address encapsulation frame-relay no ip mroute-cache clockrate 130 frame-relay intf-type dce frame-relay route 302 interface Serial0/3 203 ! interface Serial0/2 no ip address no ip mroute-cache shutdown ! interface Serial0/3 no ip address encapsulation frame-relay no ip mroute-cache clockrate 130 frame-relay intf-type dce frame-relay route 203 interface Serial0/1 302 frame-relay route 603 interface Serial0/0 306 ! ip default-gateway 10.51.1.3 ip classless no ip http server ! ! line con 0 line aux 0 line vty 0 4 login ! end -Original Message- From: sam sneed [mailto:[EMAIL PROTECTED]] Sent: Thursday, January 17, 2002 3:56 PM To: [EMAIL PROTECTED] Subject: router to use as frame relay switch [7:32348] I here there is a Cisco 2600 series router that can be used to simulate a frame relay switch. Anyone know what exact model or what is required to this. If you could explain how it works or the setup I'd appreciate it. Thnaks. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32360&t=32348 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: router to use as frame relay switch [7:32348]
Any 2600 with serial ports can act as a frame relay switch. Go to www.cisco.com and search for 'configuring frame relay switching' and you'll find all the configuration details. HTH, John >>> "sam sneed" 1/17/02 1:55:40 PM >>> I here there is a Cisco 2600 series router that can be used to simulate a frame relay switch. Anyone know what exact model or what is required to this. If you could explain how it works or the setup I'd appreciate it. Thnaks. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32359&t=32348 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: router to use as frame relay switch [7:32348]
Well you need 2 routers with WIC cards then all you have to do is configure it as a clock&switch. this url shows as a back to back config but it should give you a good idea of what's involved. You need 2 routers if you plan on doing this at home. 1 as the Data clock and the other the Data termination point. DCE / DTE http://www.cisco.com/warp/public/125/frbacktoback_hybrid.html#diagram hope this helpssam sneed wrote: > > I here there is a Cisco 2600 series router that can be used to > simulate a > frame relay switch. Anyone know what exact model or what is > required to > this. If you could explain how it works or the setup I'd > appreciate it. > Thnaks. > > Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32358&t=32348 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
router to use as frame relay switch [7:32348]
I here there is a Cisco 2600 series router that can be used to simulate a frame relay switch. Anyone know what exact model or what is required to this. If you could explain how it works or the setup I'd appreciate it. Thnaks. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32348&t=32348 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco 4000 Router as Frame-Relay Switch [7:24450]
I did read some Cisco document saying that if you setup a frame connection on a serial interface you couldn't ping the ip of that interface (probably can if you use a MAP command). However, if you setup the frame on a subinterface (S0.1, etc) then you CAN ping it. I have no idea why it's like that tho. Mike W. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=24519&t=24450 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco 4000 Router as Frame-Relay Switch [7:24450]
You can if you map the local L3 addr to the local L2 addr. For example frame-relay map ip x.x.x.x dlci# -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of McHugh Randy Sent: Monday, October 29, 2001 5:08 AM To: [EMAIL PROTECTED] Subject: Re: Cisco 4000 Router as Frame-Relay Switch [7:24450] I dont think you can ping a serial interface on the same router your on. Serial interfaces are not able to be pinged from the same device. _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=24515&t=24450 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco 4000 Router as Frame-Relay Switch [7:24450]
Encapsulation failed means that the router knows how to get to the destination, i.e. it has a directly connected interface, but doesn't know how to send the packet. Check your interfaces and make sure they are mapped and physically connected correctly. Check out the link below: http://www.cisco.com/warp/public/63/ping_traceroute.html -Original Message- From: Tim Bowyer [mailto:[EMAIL PROTECTED]] Sent: Sunday, October 28, 2001 9:30 PM To: [EMAIL PROTECTED] Subject: Cisco 4000 Router as Frame-Relay Switch [7:24450] I have configured 4000 router (FR_ROUTER) as a FR Switch. It is connected to 3 other 2500 routers (A,B,C)on serial interface. FR is working fine and I am able to ping B &C from A. But I am not able to ping the Serial Interface of A from router A itself. Same thing is happening on the other routers. I am receiving this error message : Serial0:Encaps failed--no map entry link 7(IP) IP: s=10.0.0.3 (local), d=10.0.0.3 (Serial0), len 100, encapsulation failed Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=24499&t=24450 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Cisco 4000 Router as Frame-Relay Switch [7:24450]
I dont think you can ping a serial interface on the same router your on. Serial interfaces are not able to be pinged from the same device. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=24493&t=24450 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Cisco 4000 Router as Frame-Relay Switch [7:24450]
> I have configured 4000 router (FR_ROUTER) as a FR Switch. It is connected to > 3 > other 2500 routers (A,B,C)on serial interface. FR is working fine and I am > able to ping B &C from A. But I am not able to ping the Serial Interface of A > from router A itself. Same thing is happening on the other routers. > I am receiving this error message : > > Serial0:Encaps failed--no map entry link 7(IP) > IP: s=10.0.0.3 (local), d=10.0.0.3 (Serial0), len 100, encapsulation failed Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=24492&t=24450 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Cisco 4000 Router as Frame-Relay Switch [7:24450]
I have configured 4000 router (FR_ROUTER) as a FR Switch. It is connected to 3 other 2500 routers (A,B,C)on serial interface. FR is working fine and I am able to ping B &C from A. But I am not able to ping the Serial Interface of A from router A itself. Same thing is happening on the other routers. I am receiving this error message : Serial0:Encaps failed--no map entry link 7(IP) IP: s=10.0.0.3 (local), d=10.0.0.3 (Serial0), len 100, encapsulation failed Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=24450&t=24450 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Frame relay switch question [7:18318]
On R3, Global config command of - frame-relay switching then on each serial interface of the frame switch, you need to configure some parameters. For example : interface Serial0 no ip address encapsulation frame-relay clockrate 64000 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 101 interface Serial1 111 These statement basically states that this interface is now working as a frame relays switch interface (DCE) and that it will propagate DLCI 101 towards the router. Any info coming is to this DLCI will be switched out to serial 1 and DLCI 111 on that Serial 1 interface and some other basic stuff as clockrate on this interface and such... FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Frame relay switch question [7:18318]
On Mon, Sep 03, 2001 at 02:27:26PM -0400, Lance wrote: > If the DCE interfaces are on the end routers you must use the frame-relay > switch and the frame-relay intf-type dce as well as the clockrate " " > command. Which ever router is connected to the DCE end of the cables must > have these commands entered on their serial interface. Wrong. The concepts of "DCE" and "DTE" in Frame Relay have nothing to do with DCE and DTE physical-layer connectors. In the Frame Relay world, the DCE is the network (switch) side of the UNI, and the DTE is the user side. It's a logical distinction, not a physical one. Please make sure you understand specifics like this before trying to explain them to others. -- Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=18334&t=18318 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Frame relay switch question [7:18318]
If the DCE interfaces are on the end routers you must use the frame-relay switch and the frame-relay intf-type dce as well as the clockrate " " command. Which ever router is connected to the DCE end of the cables must have these commands entered on their serial interface. It really does not matter which is the frame switch and which is the frame router. Lance ""Arun Upadhyay"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Hi Group > I want to configure frame relay switch. Here is > the thing I want to do: > I have three routers ( say R1, R2 and R3 )and two > serial cross over cable that has dte and dce > interfaces. > I want to configure router R3 as frame relay switch . > The DTE interfaces of cables I want to connect to > Router R3 and DCE interfaces to Router R1 and R2. > > R1---R3-R2 > ( dce) (DTE) (DTE) (DCE) > > Can somebody please tell me , HOW can I configure > this ? > > Thanks. > Arun > > = > Arun Upadhyay > SE Engineering > MCSE CCNA CNA > > __ > Do You Yahoo!? > Get email alerts & NEW webcam video instant messaging with Yahoo! Messenger > http://im.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=18327&t=18318 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Frame relay switch question [7:18318]
Arun- your just a handful of commands away. Have you researched this ??? The field of commands you are looking for is "Frame-Relay Switching," which makes your router into a layer 2 device. http://www.cisco.com/warp/public/125/12.html Let us know if you get stuck... All the best !!! Phil - Original Message - From: "Arun Upadhyay" To: Sent: Monday, September 03, 2001 11:43 AM Subject: Frame relay switch question [7:18318] > Hi Group > I want to configure frame relay switch. Here is > the thing I want to do: > I have three routers ( say R1, R2 and R3 )and two > serial cross over cable that has dte and dce > interfaces. > I want to configure router R3 as frame relay switch . > The DTE interfaces of cables I want to connect to > Router R3 and DCE interfaces to Router R1 and R2. > > R1---R3-R2 > ( dce) (DTE) (DTE) (DCE) > > Can somebody please tell me , HOW can I configure > this ? > > Thanks. > Arun > > = > Arun Upadhyay > SE Engineering > MCSE CCNA CNA > > __ > Do You Yahoo!? > Get email alerts & NEW webcam video instant messaging with Yahoo! Messenger > http://im.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=18325&t=18318 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Frame relay switch question [7:18318]
Hi Phil That link does not have any examples like this. All these examples assuming dce interface. I know switch configuration if it has dce interface. But I don't how to do it if it has dte interface like the one had written. Can you please write the configuration for Switch , let's say R1 is using DLCI 103 and R2 is using 203. Thanks. Arun --- Circusnuts wrote: > Arun- your just a handful of commands away. Have > you researched this ??? > The field of commands you are looking for is > "Frame-Relay Switching," which > makes your router into a layer 2 device. > > http://www.cisco.com/warp/public/125/12.html > > Let us know if you get stuck... > > All the best !!! > Phil > > - Original Message - > From: "Arun Upadhyay" > To: > Sent: Monday, September 03, 2001 11:43 AM > Subject: Frame relay switch question [7:18318] > > > > Hi Group > > I want to configure frame relay switch. Here > is > > the thing I want to do: > > I have three routers ( say R1, R2 and R3 )and two > > serial cross over cable that has dte and dce > > interfaces. > > I want to configure router R3 as frame relay > switch . > > The DTE interfaces of cables I want to connect to > > Router R3 and DCE interfaces to Router R1 and R2. > > > > R1---R3-R2 > > ( dce) (DTE) (DTE) (DCE) > > > > Can somebody please tell me , HOW can I configure > > this ? > > > > Thanks. > > Arun > > > > = > > Arun Upadhyay > > SE Engineering > > MCSE CCNA CNA > > > > __ > > Do You Yahoo!? > > Get email alerts & NEW webcam video instant > messaging with Yahoo! > Messenger > > http://im.yahoo.com > [EMAIL PROTECTED] > > > = Arun Upadhyay SE Engineering MCSE CCNA CNA __ Do You Yahoo!? Get email alerts & NEW webcam video instant messaging with Yahoo! Messenger http://im.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=18321&t=18318 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Frame relay switch question [7:18318]
Try this out: http://www.cisco.com/warp/public/125/fr_switching.html ""Arun Upadhyay"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Hi Group > I want to configure frame relay switch. Here is > the thing I want to do: > I have three routers ( say R1, R2 and R3 )and two > serial cross over cable that has dte and dce > interfaces. > I want to configure router R3 as frame relay switch . > The DTE interfaces of cables I want to connect to > Router R3 and DCE interfaces to Router R1 and R2. > > R1---R3-R2 > ( dce) (DTE) (DTE) (DCE) > > Can somebody please tell me , HOW can I configure > this ? > > Thanks. > Arun > > = > Arun Upadhyay > SE Engineering > MCSE CCNA CNA > > __ > Do You Yahoo!? > Get email alerts & NEW webcam video instant messaging with Yahoo! Messenger > http://im.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=18319&t=18318 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Frame relay switch question [7:18318]
Hi Group I want to configure frame relay switch. Here is the thing I want to do: I have three routers ( say R1, R2 and R3 )and two serial cross over cable that has dte and dce interfaces. I want to configure router R3 as frame relay switch . The DTE interfaces of cables I want to connect to Router R3 and DCE interfaces to Router R1 and R2. R1---R3-R2 ( dce) (DTE) (DTE) (DCE) Can somebody please tell me , HOW can I configure this ? Thanks. Arun = Arun Upadhyay SE Engineering MCSE CCNA CNA __ Do You Yahoo!? Get email alerts & NEW webcam video instant messaging with Yahoo! Messenger http://im.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=18318&t=18318 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Frame-Relay Switch intf-type DCE/DTE [7:14434]
common misunderstanding. clock rate should be configured on the router where the DCE end of the cable resides. this can be different than the port that is the frame relay interface-type DCE a frame switch is a DCE device with respect to a router. It can be a DTE type with regard to another frame switch. different animals, osi layers, logical versus physical connections, whatever. HTH Chuck -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Roger Sohn Sent: Tuesday, July 31, 2001 7:28 PM To: [EMAIL PROTECTED] Subject: Frame-Relay Switch intf-type DCE/DTE [7:14434] I have a hub and spoke combination going without any problems. But the only weird thing happening is that on my Frame-Relay switch (2522), I have to set the "frame-relay intf-type" to DCE for all the serial interfaces I'm using, otherwise the layer 2 connections won't come up on the hub and spoke routers. Should this be happening? I have 3 DTE ends and 1 DCE end of cables plugging into my switch. I thought if I had the DTE side of the cable plugged into my S0 of my frame relay switch, then on the interface configuration mode for "S0", I would specify the intf-type to be DTE. And vice versa if the DCE side of the cable is plugged into my switch. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=14441&t=14434 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Frame-Relay Switch intf-type DCE/DTE [7:14434]
I have a hub and spoke combination going without any problems. But the only weird thing happening is that on my Frame-Relay switch (2522), I have to set the "frame-relay intf-type" to DCE for all the serial interfaces I'm using, otherwise the layer 2 connections won't come up on the hub and spoke routers. Should this be happening? I have 3 DTE ends and 1 DCE end of cables plugging into my switch. I thought if I had the DTE side of the cable plugged into my S0 of my frame relay switch, then on the interface configuration mode for "S0", I would specify the intf-type to be DTE. And vice versa if the DCE side of the cable is plugged into my switch. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=14434&t=14434 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: AGS+ as a frame-relay switch [7:13133]
In the context of a Frame Relay switch there are two uses of DCE. On the physical layer DCE refers to the end that requires clocking. On the layer two or Frame Relay area of the config the FR Switch needs to be identified as acting as DCE equipment. So a router acting as a Frame Relay Switch can use either DTE or DCE cables. It must identify itself as DCE as Ejay gave before "frame-relay intf-type dce" Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=13147&t=13133 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: AGS+ as a frame-relay switch [7:13133]
This is exactly the same problem I was seeing before I switched the jumper on the CSC card for DTe. -Ejay -Original Message- From: Charles Ryan [mailto:[EMAIL PROTECTED]] Sent: Friday, July 20, 2001 5:28 PM To: Hire, Ejay; [EMAIL PROTECTED] Subject: Re: AGS+ as a frame-relay switch [7:13133] I'm getting this from "debug frame-relay lmi": Serial0(in): Unexpected StEnq, clock 1535608 Serial0(out): StEnq, clock 1542300, myseq 13, yourseen 0, DTE down datagramstart = 0x558B18, datagramsize = 14 FR encap = 0x00010308 00 75 95 01 01 00 03 02 0D 00 Serial0(in): Unexpected StEnq, clock 1545608 Serial0(out): StEnq, clock 1552300, myseq 14, yourseen 0, DTE down datagramstart = 0x558B18, datagramsize = 14 FR encap = 0x00010308 00 75 95 01 01 00 03 02 0E 00 Serial0(in): Unexpected StEnq, clock 1555608 Serial0(out): StEnq, clock 1562300, myseq 15, yourseen 0, DTE down datagramstart = 0x558B18, datagramsize = 14 FR encap = 0x00010308 00 75 95 01 01 00 03 02 0F 00 Serial0(in): Unexpected StEnq, clock 1565608 Serial0(out): StEnq, clock 1572300, myseq 16, yourseen 0, DTE down datagramstart = 0x558B18, datagramsize = 14 FR encap = 0x00010308 00 75 95 01 01 00 03 02 10 00 Serial0(in): Unexpected StEnq, clock 1575608 Serial0(out): StEnq, clock 1582300, myseq 17, yourseen 0, DTE down datagramstart = 0x558B18, datagramsize = 14 It's almost like it's confused that it's receiving clock source from the other end of the connection, and is trying to provide clocking on it's own. In looking at the "show controllers mci" command, it shows that the ports are setup for DTE, so now I'm really confused. Swapping cables didn't work, line protocol comes up, then goes down. I'll keep digging.. - Original Message - From: "Hire, Ejay" To: Sent: Friday, July 20, 2001 5:22 PM Subject: RE: AGS+ as a frame-relay switch [7:13133] > It doesn't matter which end of the cable is dce, as long as you are using a > dte-dce cable and the dce end is configured with a clock rate. > > I have an AGS configured as a frame-relay switch with a csc/4t serial card > and HDv.35 dce to Cisco HD60 Dte cables. I also had difficulty getting the > confuration to work until I RTFM and discovered that I had to change a > jumper on the CSC/4t serial card to place the ags ports in DCE mode. > > Here is a my config > version 10.2 > > service config > > ! > > enable secret 5 $1$1uBB$Tg1x6HtEuWjLJCsVgGEp11 > > enable password passwor > > ! > > frame-relay switching > > ! > > interface Ethernet0 > > no ip address > > shutdown > > > ... > > > interface Ethernet11 > > no ip address > > shutdown > > ! > > interface Serial0 > > ip address 10.1.0.2 255.255.255.0 > > encapsulation frame-relay > > clockrate 64000 > > frame-relay intf-type dce > > frame-relay route 16 interface Serial1 17 > > ! > > interface Serial1 > > ip address 10.2.0.1 255.255.255.0 > > encapsulation frame-relay > > clockrate 64000 > > frame-relay intf-type dce > > frame-relay route 17 interface Serial0 16 > > ! > > > ... > ! > > line con 0 > > exec-timeout 0 0 > > line aux 0 > > line vty 0 4 > > password password > > login > > ! > > end > > > > -Original Message- > From: Charles Ryan [mailto:[EMAIL PROTECTED]] > Sent: Friday, July 20, 2001 4:04 PM > To: [EMAIL PROTECTED] > Subject: AGS+ as a frame-relay switch [7:13133] > > > Apologies if this has already been covered once before. > > Quick question regarding setting up an AGS+ as a frame switch. > > Do the cables connecting to the AGS+ have to be DCE in order to get the > frame-relay switching to work, or can it still work if the cables are DTE? I > currently have DTE cables into the AGS+ and am not getting line protocol to > come up, even though the other ends are DCE and I have "clock rate 64000" > configured on the other ends. > > I also have encap frame-realy ietf on both sides, frame-relay lmi-type ansi > as well. > > I'll search the archives while I await an answer. > > Thanks! > > -Chuck > > > > _ > Do You Yahoo!? > Get your free @yahoo.com address at http://mail.yahoo.com _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=13146&t=13133 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: AGS+ as a frame-relay switch [7:13133]
Did you check the jumper the applique on the AGS+ serial interface to make it DCE? It was on the webpage that was presented in a previous email. -e- - Original Message - From: Charles Ryan To: Sent: Friday, July 20, 2001 2:44 PM Subject: Re: AGS+ as a frame-relay switch [7:13133] > I'm getting this from "debug frame-relay lmi": > > > Serial0(in): Unexpected StEnq, clock 1535608 > Serial0(out): StEnq, clock 1542300, myseq 13, yourseen 0, DTE down > datagramstart = 0x558B18, datagramsize = 14 > > FR encap = 0x00010308 > 00 75 95 01 01 00 03 02 0D 00 > > Serial0(in): Unexpected StEnq, clock 1545608 > Serial0(out): StEnq, clock 1552300, myseq 14, yourseen 0, DTE down > datagramstart = 0x558B18, datagramsize = 14 > > FR encap = 0x00010308 > 00 75 95 01 01 00 03 02 0E 00 > > Serial0(in): Unexpected StEnq, clock 1555608 > Serial0(out): StEnq, clock 1562300, myseq 15, yourseen 0, DTE down > datagramstart = 0x558B18, datagramsize = 14 > > FR encap = 0x00010308 > 00 75 95 01 01 00 03 02 0F 00 > > Serial0(in): Unexpected StEnq, clock 1565608 > Serial0(out): StEnq, clock 1572300, myseq 16, yourseen 0, DTE down > datagramstart = 0x558B18, datagramsize = 14 > > FR encap = 0x00010308 > 00 75 95 01 01 00 03 02 10 00 > > Serial0(in): Unexpected StEnq, clock 1575608 > Serial0(out): StEnq, clock 1582300, myseq 17, yourseen 0, DTE down > datagramstart = 0x558B18, datagramsize = 14 > > It's almost like it's confused that it's receiving clock source from the > other end of the connection, and is trying to provide clocking on it's own. > > In looking at the "show controllers mci" command, it shows that the ports > are setup for DTE, so now I'm really confused. Swapping cables didn't work, > line protocol comes up, then goes down. > > I'll keep digging.. > > - Original Message - > From: "Hire, Ejay" > To: > Sent: Friday, July 20, 2001 5:22 PM > Subject: RE: AGS+ as a frame-relay switch [7:13133] > > > > It doesn't matter which end of the cable is dce, as long as you are using > a > > dte-dce cable and the dce end is configured with a clock rate. > > > > I have an AGS configured as a frame-relay switch with a csc/4t serial card > > and HDv.35 dce to Cisco HD60 Dte cables. I also had difficulty getting > the > > confuration to work until I RTFM and discovered that I had to change a > > jumper on the CSC/4t serial card to place the ags ports in DCE mode. > > > > Here is a my config > > version 10.2 > > > > service config > > > > ! > > > > enable secret 5 $1$1uBB$Tg1x6HtEuWjLJCsVgGEp11 > > > > enable password passwor > > > > ! > > > > frame-relay switching > > > > ! > > > > interface Ethernet0 > > > > no ip address > > > > shutdown > > > > > > ... > > > > > > interface Ethernet11 > > > > no ip address > > > > shutdown > > > > ! > > > > interface Serial0 > > > > ip address 10.1.0.2 255.255.255.0 > > > > encapsulation frame-relay > > > > clockrate 64000 > > > > frame-relay intf-type dce > > > > frame-relay route 16 interface Serial1 17 > > > > ! > > > > interface Serial1 > > > > ip address 10.2.0.1 255.255.255.0 > > > > encapsulation frame-relay > > > > clockrate 64000 > > > > frame-relay intf-type dce > > > > frame-relay route 17 interface Serial0 16 > > > > ! > > > > > > ... > > ! > > > > line con 0 > > > > exec-timeout 0 0 > > > > line aux 0 > > > > line vty 0 4 > > > > password password > > > > login > > > > ! > > > > end > > > > > > > > -Original Message- > > From: Charles Ryan [mailto:[EMAIL PROTECTED]] > > Sent: Friday, July 20, 2001 4:04 PM > > To: [EMAIL PROTECTED] > > Subject: AGS+ as a frame-relay switch [7:13133] > > > > > > Apologies if this has already been covered once before. > > > > Quick question regarding setting up an AGS+ as a frame switch. > > > > Do the cables connecting to the AGS+ have to be DCE in order to get the > > frame-relay switching to work, or can it still work if the cables are DTE? > I > > currently have DTE cables into the AGS+ and am not getting line protocol > to > > come up, even though the other ends are DCE and I have "clock rate 64000" > > configured o
Re: AGS+ as a frame-relay switch [7:13133]
I'm getting this from "debug frame-relay lmi": Serial0(in): Unexpected StEnq, clock 1535608 Serial0(out): StEnq, clock 1542300, myseq 13, yourseen 0, DTE down datagramstart = 0x558B18, datagramsize = 14 FR encap = 0x00010308 00 75 95 01 01 00 03 02 0D 00 Serial0(in): Unexpected StEnq, clock 1545608 Serial0(out): StEnq, clock 1552300, myseq 14, yourseen 0, DTE down datagramstart = 0x558B18, datagramsize = 14 FR encap = 0x00010308 00 75 95 01 01 00 03 02 0E 00 Serial0(in): Unexpected StEnq, clock 1555608 Serial0(out): StEnq, clock 1562300, myseq 15, yourseen 0, DTE down datagramstart = 0x558B18, datagramsize = 14 FR encap = 0x00010308 00 75 95 01 01 00 03 02 0F 00 Serial0(in): Unexpected StEnq, clock 1565608 Serial0(out): StEnq, clock 1572300, myseq 16, yourseen 0, DTE down datagramstart = 0x558B18, datagramsize = 14 FR encap = 0x00010308 00 75 95 01 01 00 03 02 10 00 Serial0(in): Unexpected StEnq, clock 1575608 Serial0(out): StEnq, clock 1582300, myseq 17, yourseen 0, DTE down datagramstart = 0x558B18, datagramsize = 14 It's almost like it's confused that it's receiving clock source from the other end of the connection, and is trying to provide clocking on it's own. In looking at the "show controllers mci" command, it shows that the ports are setup for DTE, so now I'm really confused. Swapping cables didn't work, line protocol comes up, then goes down. I'll keep digging.. - Original Message - From: "Hire, Ejay" To: Sent: Friday, July 20, 2001 5:22 PM Subject: RE: AGS+ as a frame-relay switch [7:13133] > It doesn't matter which end of the cable is dce, as long as you are using a > dte-dce cable and the dce end is configured with a clock rate. > > I have an AGS configured as a frame-relay switch with a csc/4t serial card > and HDv.35 dce to Cisco HD60 Dte cables. I also had difficulty getting the > confuration to work until I RTFM and discovered that I had to change a > jumper on the CSC/4t serial card to place the ags ports in DCE mode. > > Here is a my config > version 10.2 > > service config > > ! > > enable secret 5 $1$1uBB$Tg1x6HtEuWjLJCsVgGEp11 > > enable password passwor > > ! > > frame-relay switching > > ! > > interface Ethernet0 > > no ip address > > shutdown > > > ... > > > interface Ethernet11 > > no ip address > > shutdown > > ! > > interface Serial0 > > ip address 10.1.0.2 255.255.255.0 > > encapsulation frame-relay > > clockrate 64000 > > frame-relay intf-type dce > > frame-relay route 16 interface Serial1 17 > > ! > > interface Serial1 > > ip address 10.2.0.1 255.255.255.0 > > encapsulation frame-relay > > clockrate 64000 > > frame-relay intf-type dce > > frame-relay route 17 interface Serial0 16 > > ! > > > ... > ! > > line con 0 > > exec-timeout 0 0 > > line aux 0 > > line vty 0 4 > > password password > > login > > ! > > end > > > > -Original Message- > From: Charles Ryan [mailto:[EMAIL PROTECTED]] > Sent: Friday, July 20, 2001 4:04 PM > To: [EMAIL PROTECTED] > Subject: AGS+ as a frame-relay switch [7:13133] > > > Apologies if this has already been covered once before. > > Quick question regarding setting up an AGS+ as a frame switch. > > Do the cables connecting to the AGS+ have to be DCE in order to get the > frame-relay switching to work, or can it still work if the cables are DTE? I > currently have DTE cables into the AGS+ and am not getting line protocol to > come up, even though the other ends are DCE and I have "clock rate 64000" > configured on the other ends. > > I also have encap frame-realy ietf on both sides, frame-relay lmi-type ansi > as well. > > I'll search the archives while I await an answer. > > Thanks! > > -Chuck > > > > _ > Do You Yahoo!? > Get your free @yahoo.com address at http://mail.yahoo.com _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=13143&t=13133 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: AGS+ as a frame-relay switch [7:13133]
So what am I looking for within this web page? I was actually looking for a "yes" or "no" answer, and hopefully some insight as to what else I may need to configure on the AGS+. Odd thing is, when I have it configured for normal back-to-back operations via HDLC, it works just fine. No problems whatsoever. It appears that the router is configured as DTE, as best that I can tell from the "show controllers mci" command: AGS+#sh controllers mci MCI 1, controller type 1.1, microcode version 1.11 128 Kbytes of main memory, 4 Kbytes cache memory 23 system TX buffers, largest buffer size 1520 Restarts: 0 line down, 0 hung output, 0 controller error Interface 1 is Serial0, electrical interface is V.35 DTE 14 total RX buffers, 11 buffer TX queue limit, buffer size 1520 Tx buffer in-use count is 0 Transmitter delay is 0 microseconds High speed synchronous serial interface Interface 3 is Serial1, electrical interface is V.35 DTE 14 total RX buffers, 11 buffer TX queue limit, buffer size 1520 Tx buffer in-use count is 0 Transmitter delay is 0 microseconds High speed synchronous serial interface MCI 2, controller type 1.1, microcode version 1.11 128 Kbytes of main memory, 4 Kbytes cache memory 23 system TX buffers, largest buffer size 1520 Restarts: 0 line down, 0 hung output, 0 controller error Interface 1 is Serial2, electrical interface is V.35 DTE 14 total RX buffers, 11 buffer TX queue limit, buffer size 1520 Tx buffer in-use count is 0 Transmitter delay is 0 microseconds High speed synchronous serial interface Interface 3 is Serial3, electrical interface is V.35 DTE 14 total RX buffers, 11 buffer TX queue limit, buffer size 1520 Tx buffer in-use count is 0 Transmitter delay is 0 microseconds High speed synchronous serial interface MCI 3, controller type 1.1, microcode version 1.11 128 Kbytes of main memory, 4 Kbytes cache memory 23 system TX buffers, largest buffer size 1520 Restarts: 0 line down, 0 hung output, 0 controller error Interface 1 is Serial4, electrical interface is V.35 DTE 14 total RX buffers, 11 buffer TX queue limit, buffer size 1520 Tx buffer in-use count is 0 Transmitter delay is 0 microseconds High speed synchronous serial interface Interface 3 is Serial5, electrical interface is V.35 DTE 14 total RX buffers, 11 buffer TX queue limit, buffer size 1520 Tx buffer in-use count is 0 Transmitter delay is 0 microseconds High speed synchronous serial interface MCI 4, controller type 1.1, microcode version 1.11 128 Kbytes of main memory, 4 Kbytes cache memory 23 system TX buffers, largest buffer size 1520 Restarts: 0 line down, 0 hung output, 0 controller error Interface 1 is Serial6, electrical interface is RS-232 DTE 14 total RX buffers, 11 buffer TX queue limit, buffer size 1520 Tx buffer in-use count is 0 Transmitter delay is 0 microseconds High speed synchronous serial interface Interface 3 is Serial7, electrical interface is RS-232 DTE 14 total RX buffers, 11 buffer TX queue limit, buffer size 1520 Tx buffer in-use count is 0 Transmitter delay is 0 microseconds High speed synchronous serial interface I currently have cables plugged into Serial ports 0,1,2, & 3. Serial ports 4 & 5 have no cables plugged in at the moment, and it appears that they are currently setup for DTE. Any other ideas? I'm gonna try and swap cables to see if that makes any difference. - Original Message - From: "Farhan Ahmed" To: "'Charles Ryan'" ; Sent: Friday, July 20, 2001 4:10 PM Subject: RE: AGS+ as a frame-relay switch [7:13133] > > > > > > > > http://www.cisco.com/univercd/cc/td/doc/product/core/cisagspl/agshim/69679.h > tm > > > > > > -Original Message- > From: Charles Ryan [mailto:[EMAIL PROTECTED]] > Sent: Saturday, July 21, 2001 12:04 AM > To: [EMAIL PROTECTED] > Subject: AGS+ as a frame-relay switch [7:13133] > > > Apologies if this has already been covered once before. > > Quick question regarding setting up an AGS+ as a frame switch. > > Do the cables connecting to the AGS+ have to be DCE in order to get the > frame-relay switching to work, or can it still work if the cables are DTE? I > currently have DTE cables into the AGS+ and am not getting line protocol to > come up, even though the other ends are DCE and I have "clock rate 64000" > configured on the other ends. > > I also have encap frame-realy ietf on both sides, frame-relay lmi-type ansi > as well. > > I'll search the archives while I await an answer. > > Thanks! > > -Chuck > > > > _ > Do You Yahoo!? > Get your free @yahoo.com address at http://mail.
RE: AGS+ as a frame-relay switch [7:13133]
It doesn't matter which end of the cable is dce, as long as you are using a dte-dce cable and the dce end is configured with a clock rate. I have an AGS configured as a frame-relay switch with a csc/4t serial card and HDv.35 dce to Cisco HD60 Dte cables. I also had difficulty getting the confuration to work until I RTFM and discovered that I had to change a jumper on the CSC/4t serial card to place the ags ports in DCE mode. Here is a my config version 10.2 service config ! enable secret 5 $1$1uBB$Tg1x6HtEuWjLJCsVgGEp11 enable password passwor ! frame-relay switching ! interface Ethernet0 no ip address shutdown ... interface Ethernet11 no ip address shutdown ! interface Serial0 ip address 10.1.0.2 255.255.255.0 encapsulation frame-relay clockrate 64000 frame-relay intf-type dce frame-relay route 16 interface Serial1 17 ! interface Serial1 ip address 10.2.0.1 255.255.255.0 encapsulation frame-relay clockrate 64000 frame-relay intf-type dce frame-relay route 17 interface Serial0 16 ! ... ! line con 0 exec-timeout 0 0 line aux 0 line vty 0 4 password password login ! end -Original Message- From: Charles Ryan [mailto:[EMAIL PROTECTED]] Sent: Friday, July 20, 2001 4:04 PM To: [EMAIL PROTECTED] Subject: AGS+ as a frame-relay switch [7:13133] Apologies if this has already been covered once before. Quick question regarding setting up an AGS+ as a frame switch. Do the cables connecting to the AGS+ have to be DCE in order to get the frame-relay switching to work, or can it still work if the cables are DTE? I currently have DTE cables into the AGS+ and am not getting line protocol to come up, even though the other ends are DCE and I have "clock rate 64000" configured on the other ends. I also have encap frame-realy ietf on both sides, frame-relay lmi-type ansi as well. I'll search the archives while I await an answer. Thanks! -Chuck _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=13140&t=13133 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: AGS+ as a frame-relay switch [7:13133]
tm -Original Message- From: Charles Ryan [mailto:[EMAIL PROTECTED]] Sent: Saturday, July 21, 2001 12:04 AM To: [EMAIL PROTECTED] Subject: AGS+ as a frame-relay switch [7:13133] Apologies if this has already been covered once before. Quick question regarding setting up an AGS+ as a frame switch. Do the cables connecting to the AGS+ have to be DCE in order to get the frame-relay switching to work, or can it still work if the cables are DTE? I currently have DTE cables into the AGS+ and am not getting line protocol to come up, even though the other ends are DCE and I have "clock rate 64000" configured on the other ends. I also have encap frame-realy ietf on both sides, frame-relay lmi-type ansi as well. I'll search the archives while I await an answer. Thanks! -Chuck _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=13134&t=13133 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
AGS+ as a frame-relay switch [7:13133]
Apologies if this has already been covered once before. Quick question regarding setting up an AGS+ as a frame switch. Do the cables connecting to the AGS+ have to be DCE in order to get the frame-relay switching to work, or can it still work if the cables are DTE? I currently have DTE cables into the AGS+ and am not getting line protocol to come up, even though the other ends are DCE and I have "clock rate 64000" configured on the other ends. I also have encap frame-realy ietf on both sides, frame-relay lmi-type ansi as well. I'll search the archives while I await an answer. Thanks! -Chuck _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=13133&t=13133 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: DTE interface on Frame Relay switch [7:4256]
>From what I know you could configure BACK TO BACK FRAME-RELAY WITH two routers with LMI turn off regards, Jason Yee --- Fischer Reinhold wrote: > Hi Thomas, > > i think it is not possible what you are trying to > accomplish. > You need one Router with at least two serial > interfaces dedicated > as the frame relay switch. So you need at least 3 > Routers with > serial interfaces to practice frame relay. > > Others please correct me if there is a trick to do > it with two routers. > > Greetings > > Reinhold > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] __ Do You Yahoo!? Yahoo! Auctions - buy the things you want at great prices http://auctions.yahoo.com/ Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=6189&t=4256 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: How to setup a frame relay switch for hub and spoke of [7:5176]
hi thomas try this link: http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/12cgcr/wan_c /wcfrelay.htm#xtocid2427348 right from the Cisco documentation - I searched on "frame relay switch configuration" at www.cisco.com try this one for a good example of a configuration - you can take a few minutes to make it a hub-and-spoke environment http://www.fatkid.com/html/421_ipx_with_nlsp.html - click on the frame switch and the topology buttons on the left. -e- - Original Message - From: "Thomas" To: Sent: Sunday, May 20, 2001 12:33 AM Subject: How to setup a frame relay switch for hub and spoke of [7:5174] > Hi All - I am trying to setup my lab with point-to-point frame relay > enviroment. But I have difficulty setup the frame relay switch to I can > simulate my labs. Is there any good reference out there I can use? Please > help. Thanks! > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=5176&t=5176 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
How to setup a frame relay switch for hub and spoke of [7:5174]
Hi All - I am trying to setup my lab with point-to-point frame relay enviroment. But I have difficulty setup the frame relay switch to I can simulate my labs. Is there any good reference out there I can use? Please help. Thanks! Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=5174&t=5174 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: DTE interface on Frame Relay switch [7:4256]
it can be done, i had multiple people tell me that 2 routers couldnt perform frame relay, but if you search the cisco site for back-to-back frame relay they have a configuration. i have two 2501's working fine with frame relay between s0 and s0 on both routers. the only diffence between regular config and back to back is i think keepalives are dissabled. I think one if these pages shows the config: http://www.cisco.com/warp/public/125/frbacktoback.html http://www.cisco.com/warp/public/125/frbacktoback_hybrid.html Justin M. Clark MCSE 4/2000 CCNA, CCDA ""Shibu Pillai"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Hello , > It is possible . > Sbp > ""Thomas"" wrote in message > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > If I am using a 2522 as a frame relay switch, can its A/S serial ports be > > configured as DCE interfaces and be connected to other router DTE > interfaces > > using a 60pin-60pin crossover cables? I am trying to setup a fram relay > > switch with more than 2 routers participate (excluding the frame relay > > switch router itself) so that I can create a hub router Any other > > suggestion for this configuration? Thanks. > > > > > > > > > > > > > > > > ""Fischer Reinhold"" wrote in message > > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > > Hi Thomas, > > > > > > i think it is not possible what you are trying to accomplish. > > > You need one Router with at least two serial interfaces dedicated > > > as the frame relay switch. So you need at least 3 Routers with > > > serial interfaces to practice frame relay. > > > > > > Others please correct me if there is a trick to do it with two routers. > > > > > > Greetings > > > > > > Reinhold > > > FAQ, list archives, and subscription info: > > http://www.groupstudy.com/list/cisco.html > > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4300&t=4256 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: DTE interface on Frame Relay switch [7:4256]
Hello , It is possible . Sbp ""Thomas"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > If I am using a 2522 as a frame relay switch, can its A/S serial ports be > configured as DCE interfaces and be connected to other router DTE interfaces > using a 60pin-60pin crossover cables? I am trying to setup a fram relay > switch with more than 2 routers participate (excluding the frame relay > switch router itself) so that I can create a hub router Any other > suggestion for this configuration? Thanks. > > > > > > > > ""Fischer Reinhold"" wrote in message > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > Hi Thomas, > > > > i think it is not possible what you are trying to accomplish. > > You need one Router with at least two serial interfaces dedicated > > as the frame relay switch. So you need at least 3 Routers with > > serial interfaces to practice frame relay. > > > > Others please correct me if there is a trick to do it with two routers. > > > > Greetings > > > > Reinhold > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4292&t=4256 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: DTE interface on Frame Relay switch [7:4256]
If I am using a 2522 as a frame relay switch, can its A/S serial ports be configured as DCE interfaces and be connected to other router DTE interfaces using a 60pin-60pin crossover cables? I am trying to setup a fram relay switch with more than 2 routers participate (excluding the frame relay switch router itself) so that I can create a hub router Any other suggestion for this configuration? Thanks. ""Fischer Reinhold"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Hi Thomas, > > i think it is not possible what you are trying to accomplish. > You need one Router with at least two serial interfaces dedicated > as the frame relay switch. So you need at least 3 Routers with > serial interfaces to practice frame relay. > > Others please correct me if there is a trick to do it with two routers. > > Greetings > > Reinhold > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4285&t=4256 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: DTE interface on Frame Relay switch [7:4256]
Hi Thomas, i think it is not possible what you are trying to accomplish. You need one Router with at least two serial interfaces dedicated as the frame relay switch. So you need at least 3 Routers with serial interfaces to practice frame relay. Others please correct me if there is a trick to do it with two routers. Greetings Reinhold Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4266&t=4256 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: DTE interface on Frame Relay switch [7:4256]
Absolutely. Go to www.groupstudy.com and search the archives. There's a lot of pertinent information there regarding back-to-back configurations. Generally, you'd connect the DCE side of the cable (it should be labeled) to the FrameSwitch and the DTEs to the 'spokes' > Hi All - I have two 2501 routers. One of them is set as a Frame Relay > switch. I wonder if I can set a serial port of this router to be DTE > interface and assign an IP address to it, so that I can ping this interface > from the other router (using back-to-back crossover serial cable). Thanks. > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4263&t=4256 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
DTE interface on Frame Relay switch [7:4256]
Hi All - I have two 2501 routers. One of them is set as a Frame Relay switch. I wonder if I can set a serial port of this router to be DTE interface and assign an IP address to it, so that I can ping this interface from the other router (using back-to-back crossover serial cable). Thanks. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4256&t=4256 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Protocols on frame relay switch
The serial ports will 'see' each other, but if you're configuring the hub router as a frame relay switch you are no longer routing IP through the router, you are switching frame relay frames from one interface to the other. In that scenario, an IP routing protocol is unnecessary because you are not doing IP routing. The router is switching frames based on DLCI, so this is a layer-2 function. It is no more concerned with IP addresses than a provider's frame relay switch in a real frame relay cloud. They forward frames based on layer two information only. I know I keep repeating the same concept, but I just woke up and can't form thoughts very well. HTH, John > What does that mean? I thought 2 serial ports should see each other because > they are local... > > > > "EA LOUIE" <[EMAIL PROTECTED]> wrote in message > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > "John Neiberger" <[EMAIL PROTECTED]> wrote: > > > If you're using that router as just a frame relay switch and nothing > > > else, there's no reason to run a routing protocol because it won't be > > > routing! > > > > well, it WILL be routing, but not IP...frame-relay using static DLCI > routes. > > Actually, is there a way to configure dynamic frame-relay routing? Like > for > > frame-relay SVC's? Inquiring minds WANT TO KNOW! > > > > ;-) > > > > (guess you didn't go golfing, eh John? neither did I...) > > > > -e- > > > > > > > > HTH, > > > John > > > > > > >>> "Thomas" <[EMAIL PROTECTED]> 3/30/01 4:31:22 PM >>> > > > Hi All - I am setting my 2501 as a frame-relay switch. Its 2 serial > > > ports > > > will be set as DCE for providing clock. Since I am trying to test the > > > compatiability of between IGRP and EIGRP, does it matter if I don't run > > > any > > > protocol (such as RIP, IGRP, EIGRP...) on this 2501? Thanks All! [EMAIL PROTECTED] [EMAIL PROTECTED] > > > > > > > > Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Protocols on frame relay switch
Thanks All! "EA Louie" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > When you configure your 2 serial interfaces with DLCI information, you will > need to issue frame relay route statements from one interface to the other > interface, in this manner: > > frame-relay switching > ! > interface Serial1 > no ip address > encapsulation frame-relay > keepalive 15 > frame-relay lmi-type ansi > frame-relay intf-type dce > frame-relay route 100 interface Serial2 200 > clockrate 200 > ! > interface Serial2 > encapsulation frame-relay > keepalive 15 > frame-relay intf-type dce > frame-relay route 200 interface Serial1 100 > clockrate 64000 > > > At 08:52 PM 3/30/01 -0500, Thomas wrote: > >What does that mean? I thought 2 serial ports should see each other because > >they are local... > > > > > > > >"EA LOUIE" <[EMAIL PROTECTED]> wrote in message > >[EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > > "John Neiberger" <[EMAIL PROTECTED]> wrote: > > > > If you're using that router as just a frame relay switch and nothing > > > > else, there's no reason to run a routing protocol because it won't be > > > > routing! > > > > > > well, it WILL be routing, but not IP...frame-relay using static DLCI > >routes. > > > Actually, is there a way to configure dynamic frame-relay routing? Like > >for > > > frame-relay SVC's? Inquiring minds WANT TO KNOW! > > > > > > ;-) > > > > > > (guess you didn't go golfing, eh John? neither did I...) > > > > > > -e- > > > > > > > > > > > HTH, > > > > John > > > > > > > > >>> "Thomas" <[EMAIL PROTECTED]> 3/30/01 4:31:22 PM >>> > > > > Hi All - I am setting my 2501 as a frame-relay switch. Its 2 serial > > > > ports > > > > will be set as DCE for providing clock. Since I am trying to test the > > > > compatiability of between IGRP and EIGRP, does it matter if I don't run > > > > any > > > > protocol (such as RIP, IGRP, EIGRP...) on this 2501? Thanks All! > > > > > > > > > > > > _ > > > > FAQ, list archives, and subscription info: > > > > http://www.groupstudy.com/list/cisco.html > > > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > > > > > > > > > > > > _ > > > > FAQ, list archives, and subscription info: > > > http://www.groupstudy.com/list/cisco.html > > > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > > > > > > > > Get free email and a permanent address at http://www.netaddress.com/?N=1 > > > > > > _ > > > FAQ, list archives, and subscription info: > >http://www.groupstudy.com/list/cisco.html > > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > > > > >_ > >FAQ, list archives, and subscription info: > >http://www.groupstudy.com/list/cisco.html > >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Protocols on frame relay switch
When you configure your 2 serial interfaces with DLCI information, you will need to issue frame relay route statements from one interface to the other interface, in this manner: frame-relay switching ! interface Serial1 no ip address encapsulation frame-relay keepalive 15 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 100 interface Serial2 200 clockrate 200 ! interface Serial2 encapsulation frame-relay keepalive 15 frame-relay intf-type dce frame-relay route 200 interface Serial1 100 clockrate 64000 At 08:52 PM 3/30/01 -0500, Thomas wrote: >What does that mean? I thought 2 serial ports should see each other because >they are local... > > > >"EA LOUIE" <[EMAIL PROTECTED]> wrote in message >[EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > "John Neiberger" <[EMAIL PROTECTED]> wrote: > > > If you're using that router as just a frame relay switch and nothing > > > else, there's no reason to run a routing protocol because it won't be > > > routing! > > > > well, it WILL be routing, but not IP...frame-relay using static DLCI >routes. > > Actually, is there a way to configure dynamic frame-relay routing? Like >for > > frame-relay SVC's? Inquiring minds WANT TO KNOW! > > > > ;-) > > > > (guess you didn't go golfing, eh John? neither did I...) > > > > -e- > > > > > > > > HTH, > > > John > > > > > > >>> "Thomas" <[EMAIL PROTECTED]> 3/30/01 4:31:22 PM >>> > > > Hi All - I am setting my 2501 as a frame-relay switch. Its 2 serial > > > ports > > > will be set as DCE for providing clock. Since I am trying to test the > > > compatiability of between IGRP and EIGRP, does it matter if I don't run > > > any > > > protocol (such as RIP, IGRP, EIGRP...) on this 2501? Thanks All! > > > > > > > > > _ > > > FAQ, list archives, and subscription info: > > > http://www.groupstudy.com/list/cisco.html > > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > > > > > > > > _ > > > FAQ, list archives, and subscription info: > > http://www.groupstudy.com/list/cisco.html > > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > > > > Get free email and a permanent address at http://www.netaddress.com/?N=1 > > > > _ > > FAQ, list archives, and subscription info: >http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > >_ >FAQ, list archives, and subscription info: >http://www.groupstudy.com/list/cisco.html >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Protocols on frame relay switch
What does that mean? I thought 2 serial ports should see each other because they are local... "EA LOUIE" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > "John Neiberger" <[EMAIL PROTECTED]> wrote: > > If you're using that router as just a frame relay switch and nothing > > else, there's no reason to run a routing protocol because it won't be > > routing! > > well, it WILL be routing, but not IP...frame-relay using static DLCI routes. > Actually, is there a way to configure dynamic frame-relay routing? Like for > frame-relay SVC's? Inquiring minds WANT TO KNOW! > > ;-) > > (guess you didn't go golfing, eh John? neither did I...) > > -e- > > > > > HTH, > > John > > > > >>> "Thomas" <[EMAIL PROTECTED]> 3/30/01 4:31:22 PM >>> > > Hi All - I am setting my 2501 as a frame-relay switch. Its 2 serial > > ports > > will be set as DCE for providing clock. Since I am trying to test the > > compatiability of between IGRP and EIGRP, does it matter if I don't run > > any > > protocol (such as RIP, IGRP, EIGRP...) on this 2501? Thanks All! > > > > > > _ > > FAQ, list archives, and subscription info: > > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > Get free email and a permanent address at http://www.netaddress.com/?N=1 > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Protocols on frame relay switch
"John Neiberger" <[EMAIL PROTECTED]> wrote: > If you're using that router as just a frame relay switch and nothing > else, there's no reason to run a routing protocol because it won't be > routing! well, it WILL be routing, but not IP...frame-relay using static DLCI routes. Actually, is there a way to configure dynamic frame-relay routing? Like for frame-relay SVC's? Inquiring minds WANT TO KNOW! ;-) (guess you didn't go golfing, eh John? neither did I...) -e- > > HTH, > John > > >>> "Thomas" <[EMAIL PROTECTED]> 3/30/01 4:31:22 PM >>> > Hi All - I am setting my 2501 as a frame-relay switch. Its 2 serial > ports > will be set as DCE for providing clock. Since I am trying to test the > compatiability of between IGRP and EIGRP, does it matter if I don't run > any > protocol (such as RIP, IGRP, EIGRP...) on this 2501? Thanks All! > > > _ > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Get free email and a permanent address at http://www.netaddress.com/?N=1 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Protocols on frame relay switch
If you're using that router as just a frame relay switch and nothing else, there's no reason to run a routing protocol because it won't be routing! HTH, John >>> "Thomas" <[EMAIL PROTECTED]> 3/30/01 4:31:22 PM >>> Hi All - I am setting my 2501 as a frame-relay switch. Its 2 serial ports will be set as DCE for providing clock. Since I am trying to test the compatiability of between IGRP and EIGRP, does it matter if I don't run any protocol (such as RIP, IGRP, EIGRP...) on this 2501? Thanks All! _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Protocols on frame relay switch
Hi All - I am setting my 2501 as a frame-relay switch. Its 2 serial ports will be set as DCE for providing clock. Since I am trying to test the compatiability of between IGRP and EIGRP, does it matter if I don't run any protocol (such as RIP, IGRP, EIGRP...) on this 2501? Thanks All! _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Help with frame-relay switch configuration
I hope you meant int ser0 clockrate 56000 and that you added int ser3 frame-relay route 301 interface Serial1 101 clockrate 56000 -e- mtxpert <[EMAIL PROTECTED]> wrote in message 998tg6$8l4$[EMAIL PROTECTED]">news:998tg6$8l4$[EMAIL PROTECTED]... > I have a Cisco 4000 I just received and I can't get it to take clock on 2 > interfaces at once. > Here's a copy of the config after I just typed "lock rate 56000" at the > config-if mode for serial 0. > > Current configuration: > ! > version 11.1 > service udp-small-servers > service tcp-small-servers > ! > hostname R4000 > ! > enable secret 5 $1$1ETI$xqeVrzT8qlamhBz1pI4ZA/ > ! > frame-relay switching > ! > interface Serial0 > no ip address > encapsulation frame-relay > frame-relay intf-type dce > frame-relay route 301 interface Serial1 101 > ! > interface Serial1 > no ip address > encapsulation frame-relay > clockrate 56000 > frame-relay intf-type dce > frame-relay route 101 interface Serial3 301 > ! > interface Serial2 > no ip address > shutdown > ! > interface Serial3 > no ip address > encapsulation frame-relay > frame-relay intf-type dce > ! > no ip classless > ! > ! > line con 0 > password cisco > login > line aux 0 > modem InOut > line vty 0 4 > password cisco > login > ! > end > > > Without applying clock the router won't allow the dlci's to map. > This is my first attempt with a 4000 router. > Here's the version output > > Cisco Internetwork Operating System Software > IOS (tm) 4000 Software (XX-J-M), Version 11.1(14), RELEASE SOFTWARE (fc1) > Copyright (c) 1986-1997 by cisco Systems, Inc. > Compiled Thu 04-Sep-97 21:33 by tlane > Image text-base: 0x00012000, data-base: 0x0067166C > > ROM: System Bootstrap, Version 5.2(11a), RELEASE SOFTWARE > ROM: 4000 Bootstrap Software (XX-RXBOOT), Version 10.2(11a), RELEASE > SOFTWARE (f > c1) > > R4000 uptime is 24 minutes > System restarted by power-on > System image file is "flash:xx-j-mz.111-14", booted via flash > > cisco 4000 (68030) processor (revision 0xC0) with 16384K/4096K bytes of > memory. > Processor board ID 5032615 > G.703/E1 software, Version 1.0. > Bridging software. > SuperLAT software copyright 1990 by Meridian Technology Corp). > X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. > TN3270 Emulation software (copyright 1994 by TGV Inc). > 4 Serial network interfaces. > 128K bytes of non-volatile configuration memory. > 4096K bytes of processor board System flash (Read/Write) > > Configuration register is 0x2102 > > > Any body got any ideas? > > Mike Bambic > [EMAIL PROTECTED] > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Help with frame-relay switch configuration
Make sure the cable you are using a cable with the DCE end plugged in to the serial port. You cannot set the clock rate if the cable has the DTE end plugged in to the Serial port. Use the command: show controllers Louie -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of mtxpert Sent: Tuesday, March 20, 2001 5:39 PM To: [EMAIL PROTECTED] Subject: Help with frame-relay switch configuration I have a Cisco 4000 I just received and I can't get it to take clock on 2 interfaces at once. Here's a copy of the config after I just typed "lock rate 56000" at the config-if mode for serial 0. Current configuration: ! version 11.1 service udp-small-servers service tcp-small-servers ! hostname R4000 ! enable secret 5 $1$1ETI$xqeVrzT8qlamhBz1pI4ZA/ ! frame-relay switching ! interface Serial0 no ip address encapsulation frame-relay frame-relay intf-type dce frame-relay route 301 interface Serial1 101 ! interface Serial1 no ip address encapsulation frame-relay clockrate 56000 frame-relay intf-type dce frame-relay route 101 interface Serial3 301 ! interface Serial2 no ip address shutdown ! interface Serial3 no ip address encapsulation frame-relay frame-relay intf-type dce ! no ip classless ! ! line con 0 password cisco login line aux 0 modem InOut line vty 0 4 password cisco login ! end Without applying clock the router won't allow the dlci's to map. This is my first attempt with a 4000 router. Here's the version output Cisco Internetwork Operating System Software IOS (tm) 4000 Software (XX-J-M), Version 11.1(14), RELEASE SOFTWARE (fc1) Copyright (c) 1986-1997 by cisco Systems, Inc. Compiled Thu 04-Sep-97 21:33 by tlane Image text-base: 0x00012000, data-base: 0x0067166C ROM: System Bootstrap, Version 5.2(11a), RELEASE SOFTWARE ROM: 4000 Bootstrap Software (XX-RXBOOT), Version 10.2(11a), RELEASE SOFTWARE (f c1) R4000 uptime is 24 minutes System restarted by power-on System image file is "flash:xx-j-mz.111-14", booted via flash cisco 4000 (68030) processor (revision 0xC0) with 16384K/4096K bytes of memory. Processor board ID 5032615 G.703/E1 software, Version 1.0. Bridging software. SuperLAT software copyright 1990 by Meridian Technology Corp). X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. TN3270 Emulation software (copyright 1994 by TGV Inc). 4 Serial network interfaces. 128K bytes of non-volatile configuration memory. 4096K bytes of processor board System flash (Read/Write) Configuration register is 0x2102 Any body got any ideas? Mike Bambic [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Help with frame-relay switch configuration
I was moving the cable around between ports attempting to get the serial interfaces to stay up. I forgot about the LMI configuration on 11.1. I'm upgrading to 12.X tomorrow then I'll try again. Thanks Mike B. ""Neil Schneider"" <[EMAIL PROTECTED]> wrote in message 998v5d$hh9$[EMAIL PROTECTED]">news:998v5d$hh9$[EMAIL PROTECTED]... > Are you intending to use serial 0 and 1 as the switched ports? if so you > have a config error in that S1 points to S3 not S0. I know of no reason you > cannot put a clockrate command on S0 as well, is that the problem you are > having? I think you also need to set the LMI type for IOS 11.1 > > Neil Schneider > CCNP CCSI > > ""mtxpert"" <[EMAIL PROTECTED]> wrote in message > 998tg6$8l4$[EMAIL PROTECTED]">news:998tg6$8l4$[EMAIL PROTECTED]... > > I have a Cisco 4000 I just received and I can't get it to take clock on 2 > > interfaces at once. > > Here's a copy of the config after I just typed "lock rate 56000" at the > > config-if mode for serial 0. > > > > Current configuration: > > ! > > version 11.1 > > service udp-small-servers > > service tcp-small-servers > > ! > > hostname R4000 > > ! > > enable secret 5 $1$1ETI$xqeVrzT8qlamhBz1pI4ZA/ > > ! > > frame-relay switching > > ! > > interface Serial0 > > no ip address > > encapsulation frame-relay > > frame-relay intf-type dce > > frame-relay route 301 interface Serial1 101 > > ! > > interface Serial1 > > no ip address > > encapsulation frame-relay > > clockrate 56000 > > frame-relay intf-type dce > > frame-relay route 101 interface Serial3 301 > > ! > > interface Serial2 > > no ip address > > shutdown > > ! > > interface Serial3 > > no ip address > > encapsulation frame-relay > > frame-relay intf-type dce > > ! > > no ip classless > > ! > > ! > > line con 0 > > password cisco > > login > > line aux 0 > > modem InOut > > line vty 0 4 > > password cisco > > login > > ! > > end > > > > > > Without applying clock the router won't allow the dlci's to map. > > This is my first attempt with a 4000 router. > > Here's the version output > > > > Cisco Internetwork Operating System Software > > IOS (tm) 4000 Software (XX-J-M), Version 11.1(14), RELEASE SOFTWARE (fc1) > > Copyright (c) 1986-1997 by cisco Systems, Inc. > > Compiled Thu 04-Sep-97 21:33 by tlane > > Image text-base: 0x00012000, data-base: 0x0067166C > > > > ROM: System Bootstrap, Version 5.2(11a), RELEASE SOFTWARE > > ROM: 4000 Bootstrap Software (XX-RXBOOT), Version 10.2(11a), RELEASE > > SOFTWARE (f > > c1) > > > > R4000 uptime is 24 minutes > > System restarted by power-on > > System image file is "flash:xx-j-mz.111-14", booted via flash > > > > cisco 4000 (68030) processor (revision 0xC0) with 16384K/4096K bytes of > > memory. > > Processor board ID 5032615 > > G.703/E1 software, Version 1.0. > > Bridging software. > > SuperLAT software copyright 1990 by Meridian Technology Corp). > > X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. > > TN3270 Emulation software (copyright 1994 by TGV Inc). > > 4 Serial network interfaces. > > 128K bytes of non-volatile configuration memory. > > 4096K bytes of processor board System flash (Read/Write) > > > > Configuration register is 0x2102 > > > > > > Any body got any ideas? > > > > Mike Bambic > > [EMAIL PROTECTED] > > > > > > _ > > FAQ, list archives, and subscription info: > http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Help with frame-relay switch configuration
Are you intending to use serial 0 and 1 as the switched ports? if so you have a config error in that S1 points to S3 not S0. I know of no reason you cannot put a clockrate command on S0 as well, is that the problem you are having? I think you also need to set the LMI type for IOS 11.1 Neil Schneider CCNP CCSI ""mtxpert"" <[EMAIL PROTECTED]> wrote in message 998tg6$8l4$[EMAIL PROTECTED]">news:998tg6$8l4$[EMAIL PROTECTED]... > I have a Cisco 4000 I just received and I can't get it to take clock on 2 > interfaces at once. > Here's a copy of the config after I just typed "lock rate 56000" at the > config-if mode for serial 0. > > Current configuration: > ! > version 11.1 > service udp-small-servers > service tcp-small-servers > ! > hostname R4000 > ! > enable secret 5 $1$1ETI$xqeVrzT8qlamhBz1pI4ZA/ > ! > frame-relay switching > ! > interface Serial0 > no ip address > encapsulation frame-relay > frame-relay intf-type dce > frame-relay route 301 interface Serial1 101 > ! > interface Serial1 > no ip address > encapsulation frame-relay > clockrate 56000 > frame-relay intf-type dce > frame-relay route 101 interface Serial3 301 > ! > interface Serial2 > no ip address > shutdown > ! > interface Serial3 > no ip address > encapsulation frame-relay > frame-relay intf-type dce > ! > no ip classless > ! > ! > line con 0 > password cisco > login > line aux 0 > modem InOut > line vty 0 4 > password cisco > login > ! > end > > > Without applying clock the router won't allow the dlci's to map. > This is my first attempt with a 4000 router. > Here's the version output > > Cisco Internetwork Operating System Software > IOS (tm) 4000 Software (XX-J-M), Version 11.1(14), RELEASE SOFTWARE (fc1) > Copyright (c) 1986-1997 by cisco Systems, Inc. > Compiled Thu 04-Sep-97 21:33 by tlane > Image text-base: 0x00012000, data-base: 0x0067166C > > ROM: System Bootstrap, Version 5.2(11a), RELEASE SOFTWARE > ROM: 4000 Bootstrap Software (XX-RXBOOT), Version 10.2(11a), RELEASE > SOFTWARE (f > c1) > > R4000 uptime is 24 minutes > System restarted by power-on > System image file is "flash:xx-j-mz.111-14", booted via flash > > cisco 4000 (68030) processor (revision 0xC0) with 16384K/4096K bytes of > memory. > Processor board ID 5032615 > G.703/E1 software, Version 1.0. > Bridging software. > SuperLAT software copyright 1990 by Meridian Technology Corp). > X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. > TN3270 Emulation software (copyright 1994 by TGV Inc). > 4 Serial network interfaces. > 128K bytes of non-volatile configuration memory. > 4096K bytes of processor board System flash (Read/Write) > > Configuration register is 0x2102 > > > Any body got any ideas? > > Mike Bambic > [EMAIL PROTECTED] > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Help with frame-relay switch configuration
I have a Cisco 4000 I just received and I can't get it to take clock on 2 interfaces at once. Here's a copy of the config after I just typed "lock rate 56000" at the config-if mode for serial 0. Current configuration: ! version 11.1 service udp-small-servers service tcp-small-servers ! hostname R4000 ! enable secret 5 $1$1ETI$xqeVrzT8qlamhBz1pI4ZA/ ! frame-relay switching ! interface Serial0 no ip address encapsulation frame-relay frame-relay intf-type dce frame-relay route 301 interface Serial1 101 ! interface Serial1 no ip address encapsulation frame-relay clockrate 56000 frame-relay intf-type dce frame-relay route 101 interface Serial3 301 ! interface Serial2 no ip address shutdown ! interface Serial3 no ip address encapsulation frame-relay frame-relay intf-type dce ! no ip classless ! ! line con 0 password cisco login line aux 0 modem InOut line vty 0 4 password cisco login ! end Without applying clock the router won't allow the dlci's to map. This is my first attempt with a 4000 router. Here's the version output Cisco Internetwork Operating System Software IOS (tm) 4000 Software (XX-J-M), Version 11.1(14), RELEASE SOFTWARE (fc1) Copyright (c) 1986-1997 by cisco Systems, Inc. Compiled Thu 04-Sep-97 21:33 by tlane Image text-base: 0x00012000, data-base: 0x0067166C ROM: System Bootstrap, Version 5.2(11a), RELEASE SOFTWARE ROM: 4000 Bootstrap Software (XX-RXBOOT), Version 10.2(11a), RELEASE SOFTWARE (f c1) R4000 uptime is 24 minutes System restarted by power-on System image file is "flash:xx-j-mz.111-14", booted via flash cisco 4000 (68030) processor (revision 0xC0) with 16384K/4096K bytes of memory. Processor board ID 5032615 G.703/E1 software, Version 1.0. Bridging software. SuperLAT software copyright 1990 by Meridian Technology Corp). X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. TN3270 Emulation software (copyright 1994 by TGV Inc). 4 Serial network interfaces. 128K bytes of non-volatile configuration memory. 4096K bytes of processor board System flash (Read/Write) Configuration register is 0x2102 Any body got any ideas? Mike Bambic [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Setting up a frame relay switch in a lab
I have a 4500 with a 4-port serial card that I am setting up as a frame relay switch that will host connection for three other 4000Ms. I have setup back to back connections before. My question is...Should I configure the switch like I normally do - rolled serial cable and configure the 4500 interfaces individually as the dce with clock rate. Or should I set it up some other way? Thanks _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Setting up a frame relay switch in a lab
Timothy, Not that there is any one correct way to do it but heres how I configure mine for my lab... Cory hostname frameswitch ! ! frame-relay switching ! interface Ethernet0 no ip address shutdown ! interface Serial0 no ip address encapsulation frame-relay clockrate 56000 frame-relay intf-type dce frame-relay route 101 interface Serial1 200 frame-relay route 102 interface Serial2 300 frame-relay route 103 interface Serial3 400 ! interface Serial1 no ip address encapsulation frame-relay clockrate 56000 frame-relay intf-type dce frame-relay route 200 interface Serial0 101 frame-relay route 202 interface Serial2 301 frame-relay route 203 interface Serial3 401 ! interface Serial2 no ip address encapsulation frame-relay clockrate 56000 frame-relay intf-type dce frame-relay route 300 interface Serial0 102 frame-relay route 301 interface Serial1 202 frame-relay route 303 interface Serial3 402 ! interface Serial3 no ip address encapsulation frame-relay clockrate 56000 frame-relay intf-type dce frame-relay route 400 interface Serial0 103 frame-relay route 401 interface Serial1 203 frame-relay route 402 interface Serial2 303 ! interface TokenRing0 no ip address shutdown ! interface TokenRing1 no ip address shutdown ! no ip classless ! ! line con 0 line aux 0 line vty 0 4 login ! end -Original Message- From: Roberts, Timothy [mailto:[EMAIL PROTECTED]] Sent: Tuesday, February 20, 2001 11:15 AM To: '[EMAIL PROTECTED]' Subject: Setting up a frame relay switch in a lab I have a 4500 with a 4-port serial card that I am setting up as a frame relay switch that will host connection for three other 4000Ms. I have setup back to back connections before. My question is...Should I configure the switch like I normally do - rolled serial cable and configure the 4500 interfaces individually as the dce with clock rate. Or should I set it up some other way? Thanks _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: AGS+ as a Frame Relay Switch
John, First thing is you must identify what type of interface your serial port is emulating. The only two choices you have are DTE and DCE. DTE devices(normally the router) receives a clock from the DCE(normally the CSU/DSU or network equipment) provides the clock. On the AGS's I hope you've got the HD V.35, 26 pin Serial interfaces because those are the only one that support the cables to allow back-to-back router connections to the 2500 routers(HD60) interfaces. The other thing is to support the DCE function on the AGS side you must change the jumper settings on the card it self to make it a DCE capable device. The cards comes default with the jumper settings to DTE. Here is the link that should answer any other questions you may have... http://www.cisco.com/univercd/cc/td/doc/product/core/cisagspl/agscfig/34084. htm Also, don't forget the command "sh controller "to see what the ports are configured to. HTH Nigel.. - Original Message - From: John Michalek <[EMAIL PROTECTED]> Newsgroups: groupstudy.cisco To: <[EMAIL PROTECTED]> Sent: Thursday, December 21, 2000 6:57 AM Subject: AGS+ as a Frame Relay Switch > I have an AGS+ with 8 serial ports running IOS 10.3(6). I'd like to use it > as a frame relay switch. > When I go to a serial interface and try to set the clock rate I get the > following error: > "Setting clockrate for DTE's is not allowed" > Is there a particular version of IOS that I should use? > > Here's the config: > interface serial 0 > no ip address > encapsulation frame-relay > frame-realy intf-type dce > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
AGS+ as a Frame Relay Switch
I have an AGS+ with 8 serial ports running IOS 10.3(6). I'd like to use it as a frame relay switch. When I go to a serial interface and try to set the clock rate I get the following error: "Setting clockrate for DTE's is not allowed" Is there a particular version of IOS that I should use? Here's the config: interface serial 0 no ip address encapsulation frame-relay frame-realy intf-type dce _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: how to config a frame relay switch?
R1 is acting as the telco side of the frame-relay switch. It doesn't/shouldn't care about any layer 3 protocols, just it's DLCI mappings between interfaces. -- Jason Roysdon, CCNA, MCSE, CNA, Network+, A+ List email: [EMAIL PROTECTED] Homepage: http://jason.artoo.net/ Cisco resources: http://r2cisco.artoo.net/ ""Frank"" <[EMAIL PROTECTED]> wrote in message 8vvs0e$6kh$[EMAIL PROTECTED]">news:8vvs0e$6kh$[EMAIL PROTECTED]... > yeah ,i got a type mistake in config of int s1/1,i have corrected it. > the config on dte is quite simple ,i think. > It's as follows: > R2: > interface Serial1/1 > ip address 172.16.40.1 255.255.255.0 > encapsulation frame-relay > > router ospf 1 > network 172.16.0.0 0.0.255.255 area 0 > R3: > interface Serial1/1 > ip address 172.16.30.1 255.255.255.0 > encapsulation frame-relay > > router ospf 1 > network 172.16.0.0 0.0.255.255 area 0 > > from the following result ,the frame swith works ,i think. > and i found the dte routers got DLCI automatically. > > R1#sh frame pvc > > PVC Statistics for interface Serial1/0 (Frame Relay DCE) > > Active Inactive Deleted Static > Local 0000 > Switched 1000 > Unused 0000 > > DLCI = 110, DLCI USAGE = SWITCHED, PVC STATUS = ACTIVE, INTERFACE = > Serial1/0 > > input pkts 137 output pkts 132 in bytes 11442 > out bytes 10932 dropped pkts 0 in FECN pkts 0 > in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 > in DE pkts 0 out DE pkts 0 > out bcast pkts 0 out bcast bytes 0Num Pkts Switched > 137 > > pvc create time 02:32:06, last time pvc status changed 01:57:16 > > PVC Statistics for interface Serial1/1 (Frame Relay DCE) > > Active Inactive Deleted Static > Local 0000 > Switched 1000 > Unused 0000 > > DLCI = 100, DLCI USAGE = SWITCHED, PVC STATUS = ACTIVE, INTERFACE = > Serial1/1 > > input pkts 133 output pkts 137 in bytes 11000 > out bytes 11442 dropped pkts 0 in FECN pkts 0 > in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 > in DE pkts 0 out DE pkts 0 > out bcast pkts 0 out bcast bytes 0Num Pkts Switched > 133 > > pvc create time 02:28:35, last time pvc status changed 01:57:16 > > > but the ospf seems failed ,R2 and R3 couldn't find each other ,after i add > static route,they got connected. > i don't think we need to run ospf on R1 ,right? > another question is when i run ospf neighbor command ,i got such error,why? > "R2(config-router)#nei 172.16.30.1 > OSPF: Neighbor address does not map to an interface" > > Thanks. > > frank > > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: how to config a frame relay switch?
yeah ,i got a type mistake in config of int s1/1,i have corrected it. the config on dte is quite simple ,i think. It's as follows: R2: interface Serial1/1 ip address 172.16.40.1 255.255.255.0 encapsulation frame-relay router ospf 1 network 172.16.0.0 0.0.255.255 area 0 R3: interface Serial1/1 ip address 172.16.30.1 255.255.255.0 encapsulation frame-relay router ospf 1 network 172.16.0.0 0.0.255.255 area 0 from the following result ,the frame swith works ,i think. and i found the dte routers got DLCI automatically. R1#sh frame pvc PVC Statistics for interface Serial1/0 (Frame Relay DCE) Active Inactive Deleted Static Local 0000 Switched 1000 Unused 0000 DLCI = 110, DLCI USAGE = SWITCHED, PVC STATUS = ACTIVE, INTERFACE = Serial1/0 input pkts 137 output pkts 132 in bytes 11442 out bytes 10932 dropped pkts 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0Num Pkts Switched 137 pvc create time 02:32:06, last time pvc status changed 01:57:16 PVC Statistics for interface Serial1/1 (Frame Relay DCE) Active Inactive Deleted Static Local 0000 Switched 1000 Unused 0000 DLCI = 100, DLCI USAGE = SWITCHED, PVC STATUS = ACTIVE, INTERFACE = Serial1/1 input pkts 133 output pkts 137 in bytes 11000 out bytes 11442 dropped pkts 0 in FECN pkts 0 in BECN pkts 0 out FECN pkts 0 out BECN pkts 0 in DE pkts 0 out DE pkts 0 out bcast pkts 0 out bcast bytes 0Num Pkts Switched 133 pvc create time 02:28:35, last time pvc status changed 01:57:16 but the ospf seems failed ,R2 and R3 couldn't find each other ,after i add static route,they got connected. i don't think we need to run ospf on R1 ,right? another question is when i run ospf neighbor command ,i got such error,why? "R2(config-router)#nei 172.16.30.1 OSPF: Neighbor address does not map to an interface" Thanks. frank _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: how to config a frame relay switch?
In general, the frame switch config is correct. I believe you have a typo in your frame route statement under int s 1/1 On your other routers, the interface commands are just your encapsulation frame-relay and then optionally your lmi-type and interface-dlci commands Trick of the trade. Frame-relay interface-type DCE MAY be placed on an interface that does NOT have the DCE end of the cable, and therefore does not necessarily require a clockrate. The router interface to which is connected the DCE end of the cable is the one that requires the clockrate. The two do NOT have to be the same. Have fun! Chuck -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Frank Sent: Monday, November 27, 2000 6:10 PM To: [EMAIL PROTECTED] Subject:how to config a frame relay switch? i got 3 routers connected by R1 as a framerelay switch , using s1/0 on R1 to connect with s1/0 on R2,s1/1 on R1 to connect with s1/0 on R3. According to some materials, i should config such on R1: frame-relay switching int s1/0 no ip address encap frame clock rate 64000 frame intf-type dce frame route 110 int s1/1 100 int s1/1 no ip address encap frame clock rate 64000 frame intf-type dce frame route 100 int s1/1 110 could anyone tell me the config on r2 and R3 , do i need to config any routing protocol or static router on 3 routers ? I just want to construct a NBMA environment to make a test for ospf . Thanks. frank _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
how to config a frame relay switch?
i got 3 routers connected by R1 as a framerelay switch , using s1/0 on R1 to connect with s1/0 on R2,s1/1 on R1 to connect with s1/0 on R3. According to some materials, i should config such on R1: frame-relay switching int s1/0 no ip address encap frame clock rate 64000 frame intf-type dce frame route 110 int s1/1 100 int s1/1 no ip address encap frame clock rate 64000 frame intf-type dce frame route 100 int s1/1 110 could anyone tell me the config on r2 and R3 , do i need to config any routing protocol or static router on 3 routers ? I just want to construct a NBMA environment to make a test for ospf . Thanks. frank _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Cisco Frame Relay Switch and SVC's
Hi Friends Can we configure a Cisco Routers to act as a Frame Relay Switch which supports SVC's. I want to try configuring Frame Relay SVC's and am wondering if I can configure a Cisco Router to simulate Frame Relay SVC's. Please let me know if anyone has tried out such a scenario. Thanks SV _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: 2 2501's as a frame relay switch - Once and For All
I worked through some Frame Relay scenarios last weekend and used tunnel interfaces to switch frames between three routers on an Ethernet segment (representing a core). I had several PVC's up but ran into problems when I tried the following: R1(s0 dte)(s0 dce)R2(tun 0)(tun 0)R3(s0 nni)(s1 nni)R2(tun 1)(tun 1)R4(s0 dce)(s0 dte)R5 You can see the loop between R2 and R3. All of the DLCI's were unique on each router and everything looked like it should work, but no luck. Although PVC's across these devices that didn't create a loop like this worked fine. If DLCI's are locally significant, it shouldn't matter that the PVC crossed the same router twice. Tighe Chuck Larrieu wrote: > I've been saving this one for a while also. Originally I was going to write > this off as another one of those questions. Then I got to wondering about > the genesis of it. Did a bit of research. Interesting. > > http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/wan_ > c/wcdfrely.htm#xtocid15531103 > watch this word wrap... > > the short answer to Mr. Ozbourne's question is yes it can be done. The > question itself indicates a bit of uncertainty. I know when I was > considering it, and poking around CCO, my thought was that tunnels are layer > three and frame relay is layer two and therefore no it can't be done. > > But Cisco continues to be full of surprises. The IOS is very rich in > features that allow one to do a wide variety of things in any number of > ways. Sometimes I'm too dense to understand the reasons behind the > possibilities. > > So > > 1) One may use Cisco routers as frame relay switches. > 2) One may use Cisco routers as X.25 switches > 3) One may tunnel frame relay and X.25 and SNA and any number of other > things over IP networks. > > For example, if one were migrating an enterprise to an IP only backbone, but > one had an extensive embedded base of whatever, one would take advantage of > the rich Cisco feature set to make this possible. So I have a New York > office, a Los Angeles office, and Fargo office. I want a high speed core, > using DS3. Can't do X.25 over DS3, so I have to fake out my existing X.25 > network by making my Cisco edge routers X.25 switches and tunnelingX.25 > across the backbone. OK I understand the theory. Same for SNA. But for > frame-relay I'm scratching my head. > > Network-frame_relayrouter--IP_Core_Networkrouter-fra > me-relay-network > > Possibly there might be some advantage to create such tunnels so that > routers are but one hop away from eachother? Possibly I am looking at this > the wrong way, and the issue is one of a large organization with a bunch of > Stratacom switches in various locations, and wanting to take advantage of a > high speed core somehow? I get the feeling that this feature exists as a > means of helping transition from one structure to another. I just don't > understand the structures involved. > > Chuck > > P.S. Yes Dave, your configurations will work. They are almost identical to > configurations found in the link above. > > -Original Message- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Dave > Ozbourne > Sent: Thursday, July 13, 2000 8:48 PM > To: [EMAIL PROTECTED] > Subject:2 2501's as a frame relay switch - Once and For All > > Searched the archives on Groupstudy and found varying answers on the > follwoing config, for 2 2501's connecting through a tunnel to simulate > a frame relay switch. > Does it work yes or no? > Thanks > > Cisco 2501 # 1 > ! > version 11.2 > service udp-small-servers > service tcp-small-servers > ! > hostname r1 > ! > ! > frame-relay switching > ! > interface Tunnel0 > no ip address > tunnel source Ethernet0 > tunnel destination 192.168.1.1 > ! > interface Ethernet0 > ip address 192.168.1.2 255.255.255.0 > ! > interface Serial0 > no ip address > encapsulation frame-relay > clockrate 100 > frame-relay lmi-type ansi > frame-relay intf-type dce > frame-relay route 112 interface Serial1 211 > frame-relay route 113 interface Tunnel0 311 > frame-relay route 114 interface Tunnel0 411 > ! > interface Serial1 > no ip address > encapsulation frame-relay > clockrate 100 > frame-relay lmi-type ansi > frame-relay intf-type dce > frame-relay route 211 interface Serial0 112 > ! > no ip classless > ! > line con 0 > line aux 0 > line vty 0 4 > login > ! > end > > Cisco 2501 # 2 > ! > version 11.2 > no service password-encryption > no service udp-small-servers > no service tcp-small-servers > !
frame-relay switch problem
can frame relay switches do bandwidth management on aper-IP basis even if we're on a single carrier?(satellite carrier) any help will be appreciated? thanks b4 hand Jason Yee ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: 2 2501's as a frame relay switch - Once and For All
I've been saving this one for a while also. Originally I was going to write this off as another one of those questions. Then I got to wondering about the genesis of it. Did a bit of research. Interesting. http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121cgcr/wan_ c/wcdfrely.htm#xtocid15531103 watch this word wrap... the short answer to Mr. Ozbourne's question is yes it can be done. The question itself indicates a bit of uncertainty. I know when I was considering it, and poking around CCO, my thought was that tunnels are layer three and frame relay is layer two and therefore no it can't be done. But Cisco continues to be full of surprises. The IOS is very rich in features that allow one to do a wide variety of things in any number of ways. Sometimes I'm too dense to understand the reasons behind the possibilities. So 1) One may use Cisco routers as frame relay switches. 2) One may use Cisco routers as X.25 switches 3) One may tunnel frame relay and X.25 and SNA and any number of other things over IP networks. For example, if one were migrating an enterprise to an IP only backbone, but one had an extensive embedded base of whatever, one would take advantage of the rich Cisco feature set to make this possible. So I have a New York office, a Los Angeles office, and Fargo office. I want a high speed core, using DS3. Can't do X.25 over DS3, so I have to fake out my existing X.25 network by making my Cisco edge routers X.25 switches and tunnelingX.25 across the backbone. OK I understand the theory. Same for SNA. But for frame-relay I'm scratching my head. Network-frame_relayrouter--IP_Core_Networkrouter-fra me-relay-network Possibly there might be some advantage to create such tunnels so that routers are but one hop away from eachother? Possibly I am looking at this the wrong way, and the issue is one of a large organization with a bunch of Stratacom switches in various locations, and wanting to take advantage of a high speed core somehow? I get the feeling that this feature exists as a means of helping transition from one structure to another. I just don't understand the structures involved. Chuck P.S. Yes Dave, your configurations will work. They are almost identical to configurations found in the link above. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Dave Ozbourne Sent: Thursday, July 13, 2000 8:48 PM To: [EMAIL PROTECTED] Subject: 2 2501's as a frame relay switch - Once and For All Searched the archives on Groupstudy and found varying answers on the follwoing config, for 2 2501's connecting through a tunnel to simulate a frame relay switch. Does it work yes or no? Thanks Cisco 2501 # 1 ! version 11.2 service udp-small-servers service tcp-small-servers ! hostname r1 ! ! frame-relay switching ! interface Tunnel0 no ip address tunnel source Ethernet0 tunnel destination 192.168.1.1 ! interface Ethernet0 ip address 192.168.1.2 255.255.255.0 ! interface Serial0 no ip address encapsulation frame-relay clockrate 100 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 112 interface Serial1 211 frame-relay route 113 interface Tunnel0 311 frame-relay route 114 interface Tunnel0 411 ! interface Serial1 no ip address encapsulation frame-relay clockrate 100 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 211 interface Serial0 112 ! no ip classless ! line con 0 line aux 0 line vty 0 4 login ! end Cisco 2501 # 2 ! version 11.2 no service password-encryption no service udp-small-servers no service tcp-small-servers ! hostname r2 ! ! frame-relay switching ! interface Tunnel0 no ip address tunnel source Ethernet0 tunnel destination 192.168.1.2 ! interface Ethernet0 ip address 192.168.1.1 255.255.255.0 ! interface Serial0 no ip address encapsulation frame-relay clockrate 100 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 311 interface Tunnel0 113 ! interface Serial1 no ip address encapsulation frame-relay clockrate 100 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 411 interface Tunnel0 114 ! no ip classless ! ! line con 0 line aux 0 line vty 0 4 login ! end Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Frame-relay switch for your lab
hey gang! somehow I wound up with a few too many 2520s. they've got 4 ports of serial, 1 isdn, 1 ethernet. they have 8 megs of dram and 8 megs of flash. I'll let them go at $1200+S/H. I can take Visa/MC/Amex. -Brad Ellis CCIE#5796 for more routers and switches: www.optsys.net ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: no ip address for frame-relay switch?
As usual, your knowledge astounds me!! Thank you very much for the explanation. >From: Priscilla Oppenheimer <[EMAIL PROTECTED]> >Reply-To: Priscilla Oppenheimer <[EMAIL PROTECTED]> >To: [EMAIL PROTECTED] >Subject: Re: no ip address for frame-relay switch? >Date: Fri, 14 Jul 2000 14:05:41 -0700 > >At 04:15 PM 7/14/00, Niraj Palikhey wrote: >>Hi, >>I am trying to understand as to why an ip address is not assigned to the >>serial interfaces of a router that is configured as a frame relay switch. >>Is this only for a lab environment or is this how it is also done in the >>real world? >>Also each interface is assigned as a dce interface. Why does the router >>need this to support switching? > >When I teach basic Cisco router configuration, I have the student in the >middle who is configuring the Frame Relay switch remove ip addresses to >bring home the fact that the switch is a data-link-layer device. All it has >to know is that when a frame comes in on port x with DLCI x, it should go >out port y with DLCI y. > >The router serial ports on either side of the switch should have IP >addresses and be in the same subnet. > >On the other hand, it wouldn't really hurt to have IP addresses on the >switch. With addresses, you could ping and use SNMP for troubleshooting. I >think removing the addresses is just a good pedagogical technique so that >you understand what's really going on. In the real world, I believe service >providers give switch interfaces IP addresses to facilitate >troubleshooting. > >Regarding DCE, one side of the link must use the command "frame-relay >intf-type dce." It makes most sense to put that on the switch, but in >actuality it doesn't matter which side has the command. It doesn't >necessarily have to be the side that has the DCE end of the cable connected >and the "clockrate" command configured, but once again for pedagogical >reasons I always do it on that side. So my "frame-relay switch" ends us >with the following config. (There are other ways to do it, but I like this >one): > >frame-relay switching >interface serial 0 >no ip address >clockrate 56000 >encapsulation frame-relay >frame-relay intf-type dce >frame-relay route 100 interface Serial1 200 >interface serial 1 >no ip address >clockrate 56000 >encapsulation frame-relay >frame-relay intf-type dce >frame-relay route 200 interface Serial0 100 > >Priscilla > >>Can someone help? >>Thank you. >>Kind regards, >>[EMAIL PROTECTED] >> >>Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com >> >>___ >>UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html >>FAQ, list archives, and subscription info: http://www.groupstudy.com >>Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > >Priscilla Oppenheimer >http://www.priscilla.com > >___ >UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html >FAQ, list archives, and subscription info: http://www.groupstudy.com >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: no ip address for frame-relay switch?
At 04:15 PM 7/14/00, Niraj Palikhey wrote: >Hi, >I am trying to understand as to why an ip address is not assigned to the >serial interfaces of a router that is configured as a frame relay switch. >Is this only for a lab environment or is this how it is also done in the >real world? >Also each interface is assigned as a dce interface. Why does the router >need this to support switching? When I teach basic Cisco router configuration, I have the student in the middle who is configuring the Frame Relay switch remove ip addresses to bring home the fact that the switch is a data-link-layer device. All it has to know is that when a frame comes in on port x with DLCI x, it should go out port y with DLCI y. The router serial ports on either side of the switch should have IP addresses and be in the same subnet. On the other hand, it wouldn't really hurt to have IP addresses on the switch. With addresses, you could ping and use SNMP for troubleshooting. I think removing the addresses is just a good pedagogical technique so that you understand what's really going on. In the real world, I believe service providers give switch interfaces IP addresses to facilitate troubleshooting. Regarding DCE, one side of the link must use the command "frame-relay intf-type dce." It makes most sense to put that on the switch, but in actuality it doesn't matter which side has the command. It doesn't necessarily have to be the side that has the DCE end of the cable connected and the "clockrate" command configured, but once again for pedagogical reasons I always do it on that side. So my "frame-relay switch" ends us with the following config. (There are other ways to do it, but I like this one): frame-relay switching interface serial 0 no ip address clockrate 56000 encapsulation frame-relay frame-relay intf-type dce frame-relay route 100 interface Serial1 200 interface serial 1 no ip address clockrate 56000 encapsulation frame-relay frame-relay intf-type dce frame-relay route 200 interface Serial0 100 Priscilla >Can someone help? >Thank you. >Kind regards, >[EMAIL PROTECTED] > >Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com > >___ >UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html >FAQ, list archives, and subscription info: http://www.groupstudy.com >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Priscilla Oppenheimer http://www.priscilla.com ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: no ip address for frame-relay switch?
There is no need to configure an IP address on those interfaces because you are not routing, you're switching! The router switches packets based on DLCI, nothing else. That really is how it is in the real world. In frame relay switching, as in just about everything else, there must be a DTE and a DCE. The switch can act as DCE while other connecting routers play DTE by default. I hope that makes sense, I just had lunch a while ago and I need a nap. :-) John Neiberger > Hi, > I am trying to understand as to why an ip address is not assigned to the > serial interfaces of a router that is configured as a frame relay switch. Is > this only for a lab environment or is this how it is also done in the real > world? > Also each interface is assigned as a dce interface. Why does the router need > this to support switching? > Can someone help? > Thank you. > Kind regards, > [EMAIL PROTECTED] > > Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com > > ___ > UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html > FAQ, list archives, and subscription info: http://www.groupstudy.com > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] ___ Say Bye to Slow Internet! http://www.home.com/xinbox/signup.html ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: no ip address for frame-relay switch?
A frame relay switch is a layer 2 device, it does not look at Layer 3 information. irwin -Original Message- From: Niraj Palikhey [mailto:[EMAIL PROTECTED]] Sent: Friday, July 14, 2000 4:15 PM To: [EMAIL PROTECTED] Subject: no ip address for frame-relay switch? Hi, I am trying to understand as to why an ip address is not assigned to the serial interfaces of a router that is configured as a frame relay switch. Is this only for a lab environment or is this how it is also done in the real world? Also each interface is assigned as a dce interface. Why does the router need this to support switching? Can someone help? Thank you. Kind regards, [EMAIL PROTECTED] Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
no ip address for frame-relay switch?
Hi, I am trying to understand as to why an ip address is not assigned to the serial interfaces of a router that is configured as a frame relay switch. Is this only for a lab environment or is this how it is also done in the real world? Also each interface is assigned as a dce interface. Why does the router need this to support switching? Can someone help? Thank you. Kind regards, [EMAIL PROTECTED] Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
2 2501's as a frame relay switch - Once and For All
Searched the archives on Groupstudy and found varying answers on the follwoing config, for 2 2501's connecting through a tunnel to simulate a frame relay switch. Does it work yes or no? Thanks Cisco 2501 # 1 ! version 11.2 service udp-small-servers service tcp-small-servers ! hostname r1 ! ! frame-relay switching ! interface Tunnel0 no ip address tunnel source Ethernet0 tunnel destination 192.168.1.1 ! interface Ethernet0 ip address 192.168.1.2 255.255.255.0 ! interface Serial0 no ip address encapsulation frame-relay clockrate 100 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 112 interface Serial1 211 frame-relay route 113 interface Tunnel0 311 frame-relay route 114 interface Tunnel0 411 ! interface Serial1 no ip address encapsulation frame-relay clockrate 100 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 211 interface Serial0 112 ! no ip classless ! line con 0 line aux 0 line vty 0 4 login ! end Cisco 2501 # 2 ! version 11.2 no service password-encryption no service udp-small-servers no service tcp-small-servers ! hostname r2 ! ! frame-relay switching ! interface Tunnel0 no ip address tunnel source Ethernet0 tunnel destination 192.168.1.2 ! interface Ethernet0 ip address 192.168.1.1 255.255.255.0 ! interface Serial0 no ip address encapsulation frame-relay clockrate 100 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 311 interface Tunnel0 113 ! interface Serial1 no ip address encapsulation frame-relay clockrate 100 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 411 interface Tunnel0 114 ! no ip classless ! ! line con 0 line aux 0 line vty 0 4 login ! end Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Frame Relay switch
The "DCE" that is referenced in setting up a router to use as a frame relay switch is different than the physical layer DCE reference that requires that a clock rate be defined. Connie -Original Message- From: Nigel Taylor [mailto:[EMAIL PROTECTED]] Sent: Wednesday, June 14, 2000 6:47 PM To: [EMAIL PROTECTED]; M Z Cc: Bryant Andrews Subject: Re: Frame Relay switch Taking into account that the router you have does meet all the requirements for a FR switch all that is really needed is the command; Frame_switch(config)#frame-relay switching since your frame switch is normally considered the DCE you'll also want to enable you clock rate on the connecting serial interfaces. As well you could use the following interface commands. Frame_switch(config-if)#encapsulation frame-relay Frame_switch(config-if)#clock rate 64000 Frame_switch(config-if)#frame-relay intf-type dce these are some of you basic commands for the frame switch. My $0.02 HTH Nigel - Original Message - From: M Z <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Thursday, June 15, 2000 4:14 AM Subject: Frame Relay switch > Would anyone kindly share how to config a Cisco router to act as a FR > switch. > > Thanks in advance. > > Mz > > > Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com > > ___ > UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html > FAQ, list archives, and subscription info: http://www.groupstudy.com > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Frame Relay switch
you can use lmi type cisco... -Original Message- From: ALI SHEERAZ [mailto:[EMAIL PROTECTED]] Sent: Thursday, June 15, 2000 9:17 AM To: [EMAIL PROTECTED] Subject: Re: Frame Relay switch You can configure a FR switch by using the following set of commands ..for example .a cisco router acting as a FR_Switch have its S0 and S1 configured as, interface Serial0 no ip address encapsulation frame-relay no ip mroute-cache clockrate 64000 frame-relay interface-dlci 20 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 40 interface Serial1 20 ! interface Serial1 no ip address encapsulation frame-relay clockrate 64000 frame-relay interface-dlci 40 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 20 interface Serial0 40 ALI SHEERAZ MCSE+I, MCDBA, CCNA >From: "M Z" <[EMAIL PROTECTED]> >Reply-To: "M Z" <[EMAIL PROTECTED]> >To: [EMAIL PROTECTED] >Subject: Frame Relay switch >Date: Wed, 14 Jun 2000 20:14:42 MST > >Would anyone kindly share how to config a Cisco router to act as a FR >switch. > >Thanks in advance. > >Mz > > >Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com > >___ >UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html >FAQ, list archives, and subscription info: http://www.groupstudy.com >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Frame Relay switch
goto http://www.fatkid.com/html/frame_relay_intro.html this will explain how it works and sample configs "M Z" <[EMAIL PROTECTED]> wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Would anyone kindly share how to config a Cisco router to act as a FR > switch. > > Thanks in advance. > > Mz > > > Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com > > ___ > UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html > FAQ, list archives, and subscription info: http://www.groupstudy.com > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > --- ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Frame Relay switch
You can configure a FR switch by using the following set of commands ..for example .a cisco router acting as a FR_Switch have its S0 and S1 configured as, interface Serial0 no ip address encapsulation frame-relay no ip mroute-cache clockrate 64000 frame-relay interface-dlci 20 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 40 interface Serial1 20 ! interface Serial1 no ip address encapsulation frame-relay clockrate 64000 frame-relay interface-dlci 40 frame-relay lmi-type ansi frame-relay intf-type dce frame-relay route 20 interface Serial0 40 ALI SHEERAZ MCSE+I, MCDBA, CCNA >From: "M Z" <[EMAIL PROTECTED]> >Reply-To: "M Z" <[EMAIL PROTECTED]> >To: [EMAIL PROTECTED] >Subject: Frame Relay switch >Date: Wed, 14 Jun 2000 20:14:42 MST > >Would anyone kindly share how to config a Cisco router to act as a FR >switch. > >Thanks in advance. > >Mz > > >Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com > >___ >UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html >FAQ, list archives, and subscription info: http://www.groupstudy.com >Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Frame Relay switch
1) Auto-sensing is a feature of the router IOS. IOS versios 11.2 and later support LMI auto sensing. 2) Yeah 100 and 200 are the DLCIs and this command establishes a PVC. Regards Atif Awan - Original Message - From: M Z <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> Sent: Thursday, June 15, 2000 11:12 AM Subject: Re: Frame Relay switch > Thanks Atef and Nigel for your responses, > the two other questions I have are > 1)how do you make the switch auto-sense the LMI type, or is that a function > of the router? > 2)in the command frame-relay route 100 interface serial 2 200 > are the 100 , 200 refer to the DLCI's and that is the command I need to map > a PVC between DLCI 100 and DLCI 200. > > Thanks so much. > > > > >From: "Atif Awan" <[EMAIL PROTECTED]> > >To: "M Z" <[EMAIL PROTECTED]>, <[EMAIL PROTECTED]> > >Subject: Re: Frame Relay switch > >Date: Thu, 15 Jun 2000 09:39:14 +0500 > > > >Here is a sample configuration : > > > >frame-relay switching > >! > >interface ethernet 0 > > no ip address > > shutdown > >! > >interface ethernet 1 > > no ip address > > shutdown > >! > >interface ethernet 2 > > no ip address > > shutdown > >! > >interface ethernet 3 > > no ip address > > shutdown > >! > >interface serial 0 > > ip address 131.108.178.48 255.255.255.0 > > shutdown > >! > >interface serial 1 > > no ip address > > encapsulation frame-relay > > frame-relay intf-type dce > > frame-relay lmi-type ansi > > frame-relay route 100 interface serial 2 200 > >! > >interface serial 2 > > no ip address > > encapsulation frame-relay > > frame-relay intf-type nni > > frame-relay lmi-type q933a > > frame-relay route 200 interface serial 1 100 > > clockrate 2048000 > >! > >interface serial 3 > > no ip address > > shutdown > > > >If you need any further explanation please refer to this URL : > > > >http://www.cisco.com/univercd/cc/td/doc/product/software/ios113ed/113ed_cr/ w > >an_c/wcfrelay.htm#11076 > > > > > > > >Regards > >Atif Awan > > > > > >- Original Message - > >From: M Z <[EMAIL PROTECTED]> > >To: <[EMAIL PROTECTED]> > >Sent: Thursday, June 15, 2000 8:14 AM > >Subject: Frame Relay switch > > > > > > > Would anyone kindly share how to config a Cisco router to act as a FR > > > switch. > > > > > > Thanks in advance. > > > > > > Mz > > > > > > > > > Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com > > > > > > ___ > > > UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html > > > FAQ, list archives, and subscription info: http://www.groupstudy.com > > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > > > > > > Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com > > ___ UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html FAQ, list archives, and subscription info: http://www.groupstudy.com Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
